Search Documents

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,' which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,' as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By W. S. Owen, T. Bell

The variation ox the M, temperature with nitrogen concentration has been determined experinzentally. The free-energy difference between martensite and the parent y Phase at the M, temperature,is computed for Fe-C and Fe-N alloys using recent solubility data fm the Fe-N system and new data for the variatim of the activity of the interstitial solute in the y phase with concentration. The "geometric model" is considered also, and the importance of Zener ordering is noted. It is shown that, although at any chosen concentration the M, temperature and the activity are significantly different in the two alloy systems, the free-energy duference is the same within the limits of experimental error, thus Providing further evidence of the very close similarity between the martensite transformations in Fe-C and Fe-N alloys. TO estimate the free-energy change accompanying the martensite transformation in binary interstitial alloys it is necessary to know the variation of the Ms temperature with interstitial solute concentration and some thermodynamic data. To date, only the Fe-C system has been discussed because this was the only system for which relevant experimental measurements had been made, but even in this case the data available are insufficient to permit the free-energy change to be calculated without the assumption of a thermodynamic model for the y and a solid solutions. The last comprehensive discussion of the topic was by Kaufman, Radcliffe, and Cohen in 1.960.' Since that time Ellis, Davidson, and Bodsworth2 have redeter mined the activity of carbon in y iron as a function of carbon content and Atkinson3 has measured the activity of nitrogen in Fe-N austenite. The M, temperature of Fe-N is reported in the present paper. Thus, it is now possible to assess the free-energy change accompanying the martensite transformation in Fe-N alloys on the same basis as that used to assess the change in Fe-C alloys. This comparison is of interest because it has been shown recently4 that the structure of the martensite formed in Fe-N alloys changes with nitrogen content in a manner exactly parallel to the changes in structure in the Fe-C series and that the strain associated with the distortion of the iron lattice in either the y or the a phase by a nitrogen atom is the same as that produced by a carbon atom. The work to be described tests whether or not this close similarity between the two systems extends to the thermodynamics of the martensitic transformations. THE Ms TEMPERATURES FOR Fe-N MARTENSITE Bose and Hawkes5 found the M, temperature of a eutectoid Fe-N alloy (2.35 wt pct N) to be 35°C. This single determination appears to be the only reported measurement of the M, temperature of an Fe-N alloy. In the present work a series of more than fifteen different specimens containing between 0 and 2.7 wt pct N were prepared by controlled nitriding of pure iron wire 0.010 in. diam. The iron was supplied by B.I.S.R.A. and was designated ACN2. The nitriding procedure, all aspects of which are critical, has been described in detail elsewhere.' Each specimen was quenched from the austenitizing temperature into brine at 20°C without removing the specimen from the ammonia-hydrogen atmosphere in which it was ni-trided. Alloys containing up to 0.7 wt pct N were fully martensitic. More concentrated alloys contained progressively more retained austenite. At 2.34 wt pct N the specimen was completely austenitic after quenching to 20°C. The M, temperature of specimens with M, temperature above 20°C (those containing less than 2.35 wt pct N) was determined by a thermal arrest technique. For the more concentrated alloys (2.35 to 2.70 wt pct N) the variation of electrical resistance with temperature down to -196°C was used. Unlike Fe-C alloys, Fe-N alloys cannot be reaus-tenitized in vacuum or in an inert atmosphere because excessive loss of nitrogen occurs, even in short times, at high temperatures. Consequently, the alloys were reaustenitized in the ammonia-hydrogen mixture corresponding to nitrogen equilibrium at the temperatures used. The specimens were quenched in a blast of cold hydrogen gas and the temperature, measured by a thermocouple welded to the 2.5-in.-long specimen, was recorded on a high-speed recorder. In the first experiments 0.002-in.-diam chromel-alumel wire thermocouples were used but it was found that these gave erroneous readings due to contamination by nitrogen pickup. Pt-Pt 13 pct Rh wires of 0.002 in. diam were found to be satisfactory. Further details of the experiments are available in the original thesis.7 The cooling rate was controlled between 400° and 4000°C per sec by adjusting the hydrogen pressure. At least three cooling curves were obtained for each composition. Each specimen was analyzed for nitrogen after quenching. To aid in the accurate location of the martensite arrest points a series of cooling curves of 0.010-in.-diam platinum wire were recorded and these, which did not contain an arrest, were used as comparison standards. Four specimens, each in the form of a 3-in. loop, were prepared from each of the four alloys containing more than 2.35 wt pct N. One specimen was used for nitrogen analysis, one for X-ray diffraction, and two for resistance measurements below 20°C. The latter specimens were quenched from 20°C into constant-temperature baths at selected lower temperatures.

Jan 1, 1968

By F. E. Rizzo, L. R. Bidwell, D. F. Frank

THE poor high-temperature oxidation resistance of the refractory metals becomes an important problem as higher operating temperatures are sought. A meaningful analysis of their oxidation behavior requires a knowledge of the phases that can appear during oxidation as well as their relative stability. Although several extensive investigations have been carried out to obtain this information for the W-0 system,1-10 serious inconsistencies still remain. First, the standard free energies of formation (AG°) determined in recent studies which used the solid electrolyte galvanic cell technique6,7,9 differ significantly from those obtained primarily from gas equilibration measurements.1,3,4,10 The disagreement is especially large for the highest oxides. These data have been used to predict the decomposition temperatures of WO2. 72 and WO2.90.1 A considerable extrapolation is required, resulting in a large uncertainty in the decomposition temperatures. Second, Bousquet and perachon3 have presented convincing evidence, ob- tained by gas equilibration measurements, in support of the long-contested existence of W30. Phillips and chang,ll on the other hand, were not able to observe this phase under similar experimental conditions. The purposes of this work, which is part of a continuing investigation of the W-Mo system, were to resolve the discrepancies between the AGO measured by gas equilibration and solid electrolyte galvanic cell techniques, to extend the latter measurements to lower temperatures, to redetermine the WO2.72 and WO2.90 decomposition temperatures, and to apply the more sensitive electromotive-force method to the question of the existence of W3O. I) EXPERIMENTAL PROCEDURE The measurement of ?G° of reaction by the use of calcia-stabilized zirconia solid electrolyte galvanic cells has been described previously.12 The method is based on the measurement of the difference in chemical potential of oxygen between an electrode containing the two oxides of interest and a reference electrode of known oxygen activity. Two different types of cell holders were used in this study. The first type of apparatus has been described earlier." It consisted of two solid electrodes separated by a disc of electrolyte. Both electrodes were exposed to the same stream of purified helium. With this design a gaseous transport of oxygen between the two electrodes is possible. The second type of apparatus, which has also been described earlier,14 effectively separated the two electrode atmospheres. It utilized a closed-end impervious, calcia-stabilized zirconia tube that was open to the atmosphere. The tube served as an electrolyte for the cell and provided a means for separating the anode compartment, which was held under a static vacuum, from an air reference cathode. The cells and reactions of interest are described in Table I. High-purity tungsten metal was obtained from the Fansteel Metallurgical Corp. and the Allied Chemical Corp. Table II contains an analysis of each material. WO3 was prepared by oxidizing the metal in air at approximately 600°C in high-purity recrystallized alumina boats and by the dehydration of reagent-grade tungstic acid in alundum boats. The two methods of preparing WO3 resulted in slightly different purities.

Jan 1, 1968

By M. J. Salkind

In order for fiber composite materials to find extensive use in structures, it is necessary to develop techniques for joining these materials. Riveting and adhesive bonding are two possible techniques which have been investigated although the former is less desirable because the low shear strength of most matrices makes this type of joint subject to bearing failure. Welding is an effective means of joining, especially for high-temperature applications where ad-hesives are weak; however, there are significant limitations placed on welding composite materials. The commonly used fusion welding techniques will find less use for joining composites because the two phases are often unable to stand exposure to such a stringent environment. In the case of eutectic composites, fusion welding will completely destroy the controlled microstructure. Solid-state techniques such as diffusion bonding offer potential success with certain design requirements placed on such joints. Since the primary mechanism of load transfer from matrix to fiber is shear parallel to the fibers, little load can be transferred across a butt-welded interface perpendicular to the aligned fibers. Successful joint designs must have a component parallel to the fibers to allow a shear area for load transfer. Configurations such as lap and scarf welds are likely to be successful. This note describes some results of experiments with diffusion-bonded joints in A13Ni whisker-reinforced aluminum. The composite material, prepared by unidirectional solidification of the A1-A13Ni eutectic, is described elsewhere.'-' It consists of aligned micron size whiskers in a matrix of aluminum. Since it has been shown that the microstructure of

Jan 1, 1969

By Ben-Zion Weiss, Melvin R. Meyerson

FATIGUE crack propagation in some aspects can be viewed as being a result of localized plastic deformation concentrated near the tip of the crack.' Deformation is influenced by microstructure which in turn can affect the fatigue crack growth significantly. To study the effect of localized microstructural changes on fatigue crack propagation, cantilever-type notched specimens were subjected to cyclic bending at constant load amplitude. The extent of fatigue crack propagation was obtained by measuring the length of the crack by periodic observation with a microscope on the polished side of the sample,2"4 and these data were used in preparing the curves in the figures which follow. Figs. 1 (solid lines) and 2 show experimental results obtained in austenitic type 302 stainless steel containing higher than standard carbon (0.24 pct C) and 310 stainless steel. Both steels were homogenized for 8 hr at 1120°C and then water-quenched in order to prevent the precipitation of carbides. Fig. 3 shows experimental results obtained on 9440 low alloy steel in the normalized condition and in the quenched and tempered (580°C) condition. Indications of microstructural influence can be seen in scattering of the experimental data. The degree of scattering depends on both the microstructure and the amount of cyclic stress applied to the sample. For microstructures which are more easily deformed plastically, e.g., normalized or annealed as compared with hardened and tempered structures, the scattering is greater. Similarly, higher stresses produce greater scattering in the results, regardless of whether the cause of the stress increase is due to initial loading conditions or the growth in crack length. Scattering is believed to be a result of partial redistribution in the stress field around the tip caused by plastic deformation. This opinion is borne out by much smaller scattering of experimental results in the austenitic 302 high-carbon (0.24 pct C) steel. In this steel, plastic deformation in the neighborhood of the crack causes partial mar-tensitic transformation of metastable austenite,5 which in turn restrains further plastic deformation. As a result, the stress redistribution around The tip is reduced. Partial martensitic transformation was confirmed

Jan 1, 1969

By R. W. Armstrong, P. C. Jindal

WE should like to point out that Hu and cline.1 in their study of the recrystallization of titanium, have obtained data which appear very important for accurately determining the dependence of hardness on grain size for this material. It has been proposed2,3 that the macrohardness. H. of a poly crystalline material should depend on its average grain diameter, l. in accordance with the relationship: H =H0 + kHl-1/2 [1] where Ho and kH are experimental constants. This relationship follows from the hardness dependence on yield stress or flow stress4 and. thence. the Hall-Petch stress-grain size relations.5'6 Fig. 1 shows the Diamond Pyramid Hardness. Dph. values vs the reciprocal square root of the average diameter of the recrystallized grains, taken from the titanium data reported by Hu and Cline. The data in this figure give a linear relationship for the hardness over a wider range of grain diameters than anyone has previously measured. The data are not linear, for example. on an I-1 or l-1/3 scale. At the very large grain sizes the data are in reasonable agreement with measurements earlier reported by Holden, Ogden, and Jaffee.7 For the grain sizes smaller than 1 µ, which correspond in Fig. 1 to hardness values greater than 150, the material was reported as not being completely recrystallized and, therefore, these data appear less meaningful as far as the hardness dependence on grain size is concerned. However. it has been suggested by other investigators that deformed materials exhibit strengthening due to an effective grain size refinement even in the unrecrys-tallized condition.8-10 Also. Hu and Cline have shown that a change in texture occurs for titanium during the recrystallization process and. especially. following it. The influence of this texture change on the hardness-grain size relation would be expected to be less than that reflected in the unidirectional stress-strain behavior, even for an hcp material. because of the actual combined stress system which applies for the hardness test. For, at least, certain combined stresses, average values of the orientation factors should still occur in the stress-grain size analysis of a material exhibiting a preferred orientation.' We previously suggested3 that the experimental constants. H0 and kH. from the Meyer hardness-grain size relation should be correlated with the Hall-Petch constants, uoy and ky.5,6 Our recent study" of the Hall-Petch relation and the hardness-grain size results which obtain for a number of polycrystalline materials shows that: The inequality [2] is explained by noting that the hardness should be correlated. perhaps, with the flow stress at some value of strain, as suggested by Dugdale,12 and. also, that the influence of strain on the Hall-Petch relation is to increase uo and not change k very much." Normally. Dph values and Brinell hardness values are nearly equivalent to each other and to the Meyer hardness number. For the case of titanium, then. the inequality [2] may be evaluated using the experimental values of ao = 8.0 kg per sq mm and ky = 1.3 kg per mm3/2 obtained from the experiment of Guard.6,13 Thus, (Ho/uo) = 12 and (kH/k3) = 1.3. This research has been supported at the University of Maryland through the Center of Materials Research by the Advanced Research Projects Agency of the U.S. Government.

Jan 1, 1969

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By B. Trentini

In the spectacular development of pure oxygen steel-making, the process using the vertical lance converter LD, is at the present time the most widely employed. Proper control of slag composition during the steel-making process appears to be essential in achieving satisfactory blowing from both the metallic yield and metallurgical points of view. The paper illustrates the primary importance of the presence of a large quantity of metal droplets in the slag during the process. In the case of both phosphorus and hematite pig iron, it can be deduced from the phase diagrams and confirmed by experimentation that nonhomogeneous slags are one of the causes of slag overflowing during the blow. The problem is however a complex one and further physicochemical studies appear necessary. Finally, the new continuous steelmakingprocess developed by IRSID is described. PEOPLE who knew Henri Marion Howe have said that he took great pleasure in speculating on the future of metallurgical processes. It is therefore not inappropriate to devote, in his memory, some description and discussion to processes unknown to the world of his time, in particular oxygen steelmaking and continuous steelmaking. The first industrial application to steelmaking of tonnage oxygen produced by air liquefaction was made in Germany just before the war and consisted in enriching the air blown through the bottom of a basic Begsemer converter in order to melt a higher proportion of scrap and to produce steels with lower nitrogen content than is achieved with conventional practice. While this process was being developed after the war, mostly in Western Europe, steelmakers were becoming increasingly familiar with the technique of blowing pure oxygen from the top, first by means of consumable steel pipes, with or without refractory shielding, and later by water-cooled lances, designed for the purpose and affording longer life. The field was then open for the wide use of pure oxygen in steelmaking, either in existing processes such as open-hearth or electric furnace, or in new processes. These new processes can be broadly classified according to the category of furnace employed. In the case of the vertical converter taken as the first category, bottom-blowing of pure oxygen causes extremely rapid wear of the refractory tuyeres, and although various expedients have been tried to overcome this drawback (such as mixing oxygen with CO2 or H2O or using high pressure oxygen), they have had to be abandoned. The solution for vertical converters has been found in top-blowing with a vertical water-cooled lance; this is known as the LD process or basic oxygen converter process.

Jan 1, 1969

By A. U. Seybolt, V. A. Phillips

Binary iron alloys containing 1 pct of Al, Cr, Mn, Mo, Si, Ti, or V, and 0.4 pct C, 1 pct Cr steels with and without 1.2 pct A1 or 2.0 pct Ti additions, were ion-nilrided at 550° to 600° in N-H mixtures. Nitriding increased the inicrohardne ss of all the binary alloys except those containing manganese or molybdenutn, and also hardened the heat-treated steels if aluminum or titanium urns present. Transmission electron microscopy revealed particle formation in all casts where hardening occurred. Electron diffraction gare positive identifications for ALN, CrN, and a, Si3N4 in the binary alloys, and AlN and CrN in the aluminum- cold chromium-bearing steels, respectil&apos;uly. Cubic VN with a, = 4.13A was tentatively identified. Particles, apparently of CrN, also formed in the base steel but did not increase the hardness very much. Chromium and vanadium formed nitride platelets on {001}° matrix planes, while titanium gave clusters <15A diam. Aluminum nitride precipitated at grain and subgrain boundaries, and within the grains. Silicon gave profuse precipitates of several Morphologies at grain boundaries and cubical particles within the grains. No effect of the alloy carbides on nitride precipitation was observed in the heat-treated steels. THE nitriding of steel has been a well-established commercial process for about 40 years, but in spite of this comparatively long period of use there have been few studies aimed at understanding the process. Most studies, like the early but very competent work of Jones and organ&apos; and nones.&apos; were concerned with establishing the pertinent engineering variables of steel composition, gas composition, temperature, and time. As far as the present authors are aware, there have been no studies of the composition, size, shape, or distribution of the nitrides formed in the nitriding of steel. Noren and Kindbom3 did, however, examine a few nitrided steels by surface replica electron microscopy, and were able to show the presence of car-bonitrides and AlN and TiN nitrides. pitsch4,5 and Hrivnak6 examined nitrided pure iron by transmission electron microscopy. Baird7 found manganese nitrides in Fe-1.6 pct Mn when nitrided at 650°C, using the same technique. In the present work, emphasis was placed on transmission electron microscopy because of its inherently better resolution, using principally binary alloys of iron containing 1 pct of alloying element. In addition, a few simple 0.4 pct C steel compositions were examined to investigate possible carbonitride formation. It was not anticipated that all of the added elements would form nitrides under the conditions used, but it was considered desirable to obtain direct experimental evidence on this point. It would be considerably easier to ascertain the presence of alloy nitrides by examining appropriate binary alloys in preference to relatively complex steels. The work reported here could have been done using orthodox ammonia-nitriding procedures, but an operating ion-nitriding equipment was available, and was therefore used for specimen preparation. EXPERIMENTAL DETAILS 1) Materials. Binary alloys were made up from vacuum-melted electrolytic iron with 1 wt pct additions of Cr, Ti, V, Al, Mn, Mo, and Si of about 99.9 pct purity. In addition, three steels were similarly made up—a basis steel with 1 wt pct Cr and 0.4 wt pct C and two steels with further additions of 1.2 wt pct A1 or 2.0 wt pct Ti, respectively. The materials were vacuum-melted and cast as 11-lb heats into tapered square molds of about 2 by 2 in. average cross section. The castings were forged and hot-rolled to 11/4 in. rounds. Discs of 4 in. thickness by about 1 in. diam were machined from the rods. Some of these discs were hot-forged and hot-rolled to about 0.020 in. thick, sand-blasted, and then cold-rolled to about 0.003 in. thick. At this point, the surface was cleaned by light etching with HC1, then washed, dried, and vapor-degreased prior to nitriding. 2) Ion-Nitriding Procedure. The type of ion-nitriding equipment used here is similar to that described by Jones and Martin.8 Briefly, a mixture of nitrogen and hydrogen at 5 mm total pressure is placed in a vacuum chamber with a dc potential of 450 to 500 v applied between the work (cathode) and the grounded metal vacuum enclosure (anode). Nitrogen ions are accelerated to the work where a thin layer of Fe4N forms on the surface and thus sets up a nitrogen concentration gradient. This causes nitrogen atoms to diffuse into the surface layers of the alloy forming a finely divided dispersion of alloy nitrides, causing hardening of the surface. In the work to be reported here. the nitriding was carried out at 550° to 600°C to be consistent with commercial nitriding practice. The temperatures cited are those measured by a thermocouple located under a platform on which the work was sitting. Except where otherwise stated, the mixture used in nitriding the binary alloys contained -2.0 pct N, balance hydrogen. The nitrogen concentration in the nitriding gas mixture used for the binary alloys was purposely kept lower than normally used in nitriding steels. 10 to 20 pct, in order to minimize Fe4N formation. In this way only the alloy nitrides would be present as a second phase. However, in the case of steels which would contain a- carbide phase along with as

Jan 1, 1969

By M. I. Jacobson, A. S. Yue, A. E. Vidoz, F. W. Crossman

An equation governing the concept of constitutional supercooling under the combined effect of concentration and temperature gradients was used to produce platelike Al-CuAl2 eutectic composites for mechanical properties studies. Compression specimens were prepared from a single-colony Al-CuA12 eutectic composite ingot, 2 in. in diam and 12 in. long. The specirrzens were cut such that the platelets were oriented parallel, 45 deg, and perpendicular to the compression direction. Since the ingot was of eutectic composition, The aluminum-rich matrix could dissolve 5. 7 wt pct Cu in solid solution, and therefore could be strengthened by precipitation hardening. Specimens were tested at room temperature and elevated temperatures in the unidirectionally solidified, solution-treated, and solution-treated plus aged conditions. The results were compared with those for the conventionally cast and extruded specimens. For the controlled material, the highest strengths were obtained with platelets oriented parallel to the compression axis. In the unidirectionally solidified condition, 0.2 pct offset yield strength was 32,000 psi; however, this was increased to 59,000 psi by solution treatment, and further increased to 90,500 psi by solution treatment and aging. The attainment of high compressive strengths in the Al-CuAl2 eutectic composites was interpreted in terms of the buckling of elastic CuAl2 platelets in the plastically deformed a aluminum matrix. SINCE the discovery of high-strength whiskers,&apos; scientists and engineers have made significant progress toward incorporating these whiskers into metallic matrices, forming composites for basic studies and structural application. The general procedure is to produce the whiskers first and then to bind them together with a ductile matrix. The production of whisker-reinforced composites requires tedious handling techniques,, particularly when it is desired to align the whiskers unidirectionally. Furthermore, the interfacial bond between the whisker and the matrix is frequently poor3 so that the resulting composite has strengths lower than expected. These disadvantages are generally true for any metallic composite produced by physically mixing the components. It is possible to eliminate these shortcomings by growing whiskers directly in the matrix material by eutectic solidification.4-8 In eutectic solidification, the matrix phase and a whisker phase are grown approximately simultaneously from a liquid of the same overall composition at the eutectic temperature. If the solidification process is controlled by varying the freezing rate, the temperature gradient, and the impurity content, platelike or filamentlike whiskers are produced parallel to the growth direction. The morphology of the grown-in reinforcement, i.e.. plates or rods, generally depends on the volume fraction9 of the dispersed phase present in the eutectic mixture. Since the unidirectional eutectic solidification is a one-step process, i.e., the liquid-solid transformation process, an excellent interfacial bond between the matrix and whisker is obtained. An additional advantage is that no special handling technique for whiskers is needed. In recent years, many investigators10-13 have studied the effects of growth variables on the micromorpholo-gies of binary eutectic alloys produced by controlled solidification. The study of their mechanical properties was initiated by Kraft and coworkers14-16 who found that the strength of cast A1-CuA12 eutectic alloy can be increased threefold by unidirectional solidification. In the A1-AL3Ni system, a strength of 50,000 lb per sq in, was reported for the unidirectionally solidified eutectic alloy, a value five times higher than for conventionally cast material. Thus, the unidirectionally solidified eutectics can be used as fiber-reinforced composite materials. In this paper, we shall first use an equation17 as a guide for the production of eutectic composites in general and the Al-33 wt pct Cu eutectic in particular. Experimental data supporting the theoretical prediction are given. Second, the compressive properties of the grown A1-33 wt pct Cu eutectic were thoroughly investigated in terms of platelet orientations, thermo-mechanical treatment, and temperature. The experimental data are interpreted in terms of a buckling model of fibers in elastic fiber-plastic matrix metallic composites. EXPERIMENTAL PROCEDURE Crystal Growth. The following experimental procedure was adopted for the production of controlled microstructures in the A1-33 wt pct Cu eutectic alloy. The controlled solidification was accomplished with a movable resistance-wound radiation furnace. Fig. 1 is a schematic drawing of the solidification apparatus. A water-cooled chiller was placed into a degassed high-purity graphite crucible containing the charge. Rubber stoppers wrapped with aluminum foil were used to seal both ends of the quartz tube through which a dried argon atmosphere was passed under a slight positive pressure. At both ends of the quartz tube, radiation shields were used to minimize heat loss. The quartz tube was held in place by two steel clamps and the furnace was drawn vertically by means of a steel cable against the steel truss which permits the furnace to move without touching the tube. The drive mechanism consisted of two pulleys, a counter weight.

Jan 1, 1969

By D. F. Kaufman, V. V. Damiano, G. J. London, L. R. Aronin

Beryllium bicrystals were Prepared by a seeding and floating zone-melting technique from high-purity beryllium single-crystal material. The starting material was given six floating zone purification passes prior to producing the bicrystals. Symmetric, asymmetric, and antisymmetric bicrystals were tested in tension. Included were bicrystals with boundaries both parallel and perpendicular to the tension axis. Modified symmetric bicrystals were also examined in detail. In these cases, the angles made by the slip planes with the boundary were not equal. Failure by (0001) cleavage, (1180) cleavage, and boundary separation were all observed depending on the orientation of these cleavage planes and the boundary with respect to the tension axis. Failure occurred on whichever system experienced the greatest normal stress. The origin of the fractures observed and the operative dislocation mechanisms were investigated by frac-tography and transmission electron microscopy. The results indicate that low-angle boundaries form in close proximity to the bicrystal boundary and act as sites for crack nucleation. It has been concluded that, although macroscopic compatibility was satisfied in many of the bicrystals examined, the bicrysta1 boundary was effective in Producing "early" failure by local bend plane formation as plastic deformation proceeded, followed by cleavage initiation and crack propagation. SINGLE crystals of high-purity beryllium oriented with the basal plane inclined 45 deg to the tension axis exhibit a critical resolved shear stress of about 300 psi and 200 pct extension by slipping only on the basal plane before failure by cleavage on that plane. Single crystals, oriented with the basal plane parallel to the tension axis, deform by prism slip at a critical resolved shear stress of 9000 psi and exhibit an extension of over 100 pct before failure in a ductile manner.&apos; In contrast to the behavior of single crystals, poly-crystalline beryllium deformed in tension or bending exhibits little or no ductility at room temperature. Beryllium&apos;s lack of ductility at room temperature has been attributed to its lack of a sufficient number of independent slip systems. Beryllium has only four independent slip modes at room temperature and according to the Taylor2 and von Mises3 criteria at least five independent shear modes are necessary to completely satisfy the strain compatibility conditions at all the boundaries in a random polycrystalline sample. Studies of beryllium bicrystals thus appear to provide a convenient way in which to determine whether the condition of strain compatibility is a necessary and sufficient condition to prevent failure and whether obviously incompatible boundary conditions result in boundary separation. Bicrystal studies, although not providing all of the constraints encountered in polycrystalline samples, do allow one to select very specific orientation relation-

Jan 1, 1969

By M. J. Marcinkowski, A. S. Sastri

A detailed compressive stress-strain analysis and transmission electron microscopy investigation has been made of the deformation behavior occurring in a 50 at. pct Ni-Ti (hypoeutectoid) alloy and a 54.5 at. pct Ni-Ti (hypereutectoid) alloy. In the case of the hypoeutectoid alloy, three stages of work hardening are observed. Stage I occurs at a very low stress and is associated with plastic deformation via martensite formation. Stage 11 is characterized by very rapid work hardening and is due to difficulties in causing further deformation in the fine martensite aggregate produced in Stage I. Stage III which occurs at very high stress levels is characterized by smaller work hardening rates and is due to the plastic deformation arising from alternate reconversions of the original martensites to martensites of varying orientation. Rapid quenching of the hypereutectoid alloy leads to very high yield strengths and is related to a fine precipitate dispersion that such treatment brings about. The present investigation represents the final phase of a three-part study directed toward an understanding of the solid-state transformations in near equi-atomic Ni-Ti alloys as well as the deformation mechanisms associated with these alloys. In the first part,"2 to be henceforth referred to as I, it was found that alternate simple shears on {112} planes and in (111) directions convert the parent B2 structure in the equiatomic NiTi alloy into two distinct close-packed monoclinic martensites. All of the marten-sites were of this type, whether they were formed by cooling or by plastic deformation, whether induced to form in bulk samples or in thin foils, or whether examined in the electron microscope at room temperature or below. On the other hand, in the second part of this investigation,3 to be reffered to as 11, it was shown that upon slow cooling to about 640°C. alloys in the neighborhood of NiTi which possess the B2 structure transform eutectoidally into their equilibrium phases Ti2Ni and TiNi3. However, preceding the formation of these equilibrium phases a series of metastable intermediate phases are formed. This paper will set as its goal the elucidation of the remarkable deformation behavior exhibited by NiTi. In particular, Buehler and Wiley4 have found equiatomic NiTi to be surprisingly soft, while Buehler et al.5 have shown this alloy to possess a memory effect: i.e., upon bending at room temperature it will revert to its original shape when heated to above about 50°C. In I it was shown that NiTi was soft in the sense that the yield stress was low; nevertheless, the alloy work-hardened at an extremely rapid rate to very high stress levels. On the other hand, the hypereutectoid alloys with somewhat higher nickel, say 54.5 at. pct (60 wt pct) have enormously increased yield strengths compared to those of the equiatomic alloys. In order to determine the atomistic processes giving rise to the above behavior, it was decided to examine samples that were wafered from bulk specimens deformed in compression to various strains using the techniques of transmission electron microscopy. EXPERIMENTAL TECHNIQUE All of the alloys used in the present investigation contained either 50 at. pct Ni (55.06 wt pct) or 54.5 at. pct Ni (60 wt pct) and were arc-melted in the form of a finger using the same techniques described in I and II. The finger was capsulated in a stainless-steel jacket and swaged at 850°C into rods. Compression specimens 0.300 in, long and 0.200 in. in diam were machined from these rods. In order to completely re-crystallize the samples and remove residual stresses, all of them were capsulated in evacuated quartz, annealed for 1/2 at 1050°C. and then furnace-cooled. Compression tests were carried out in an Instron tensile testing machine covering a range of temperatures from —196° to 200°C using procedures described previously.6&apos;7 In all cases crosshead speed was 0.02 in. per min. Wafers 0.015 in. thick were spark-cut from the cylindrical samples at 45 deg to the compression axes after they had been deformed to the desired strain. These specimens were then spark-planed to about 0.005 in. and then electrochemically thinned for examination by transmission electron microscopy as described in I.

Jan 1, 1969

By E. R. Russell, N. E. Richards

The current ejyiciency of aluminum cells was derived from the metal produced over a period of time and the theoretical faradaic yield. The difference in the actual amount of aluminum in the cathode at the beginning and end of the period must be determined. The weight of aluminum in the cathode was calculated from the dilution of an added quantity of impurity metal. Use of multiple indicator metals, copper, manganese, and titanium, demonstrated that the weight of aluminum in cells can be determined to within 1 pct with routine but careful chemical analyses. Over intervals of the order of 30 days, current efficiencies reliable to within 1 pct can be obtained. INVESTIGATIONS beginning with those of Pearson and waddington ,&apos; through the most recent published work of Georgievskii,9-11 illustrate the direct relationship between the composition of the anode gas and the applicability of analysis of anode gases to the control of alumina reduction cells. McMinn12 noted the lack of an independent method for measuring cell production efficiency over the short term. There is no doubt that changes in the current efficiency are immediately reflected in the composition of anode gases. However, the accuracy of faradaic yields calculated from gas analyses depends upon the degree of interaction between primary anode gas and Carbon.6 A conventional industrial practice of obtaining long-term current efficiency for production units from mass balances and quantity of electricity is generally insensitive to the impact of planned control of any one or more of the influential reduction cell parameters such as temperature, alumina concentration, and mean interelectrode distance. Consequently, there is a real need in the aluminum industry for a procedure to obtain the absolute cell current efficiency over a short term—10 to 30 days—both for the calibration of values obtained from gas analysis6 and for evaluating the effect of controlling specific parameters in the reduction process. The amount of aluminum produced may be determined by considering the cathode pool as a reduction of an impurity metal in aluminum. Analyses over a period will show a decreasing concentration of the impurity due to the accumulation of aluminum solvent. The increase in aluminum inferred from analyses is the amount produced by the cell during the period. Combining weights of the cell aluminum in the cathode at the beginning and end of a specific period, weights of aluminum tapped and the quantity of electricity passed during the interval will yield the current efficiency. Smart,I3 Lange;4 Rempel,15 Beletskii and Mashovets,16 and winkhaus17 have used dilution techniques to determine aluminum inventory in alumina reduction cells. A technique for determining the weight of aluminum in production cells by addition of small amounts of copper to the aluminum cathode was described by smart.13 The precision in values of the aluminum reservoir through dilution of copper in the cathode ranged from about 1 to 3 pct depending upon the quantity of copper added in the range 0.2 to 0.01 wt pct, respectively. Because the method appears so direct and apparently simple, one would not anticipate difficulties in application to industrial cells. The objective of this study was to resolve this problem associated with the trace metal dilution technique for determining the amount of aluminum in a cell. The approach in evaluating trace metal dilution as a basic factor in determining the weight of aluminum in the cell reservoir, and the absolute current efficiency of the Hall-Heroult cell, was to dilute more than one trace metal in the aluminum cathode so that we could discriminate among complications arising from physical mixing, the possibility of separation of intermetallic compounds, loss of the added elements, and chemical detection. EXPERIMENTAL METHODS These experiments are not complex but require standardized procedures. The technique involves addition of the trace metals to the cathode, knowing when these metals are homogeneously distributed in the liquid cathode, timing of the sampling, employing accurate and precise analytical methods, using reliable procedures for monitoring the amount of electricity passed through the cell, and accurate weighing of aluminum removed from the cell during the particular period. More accurate results might be obtained if the increment in concentration of the added indicator metals were of the order of 0.1 to 0.2 wt pct. The method must be applicable to production units and, hence, the contamination of the aluminum minimized. For this reason, the concentration of trace metals in the cathode was kept below 0.07 wt pct and generally at 0.04 wt pct level. Trace quantities of copper, manganese, titanium, and silicon are already present in virgin aluminum and are suitable as additives from electrochemical and analytical points of view. Concentration of silicon is quite dependent upon the characteristics of the raw materials and was not used extensively in this work. Chemical Analyses. All instrumental analyses require calibration against an absolute technique such as a gravimetric, volumetric, or spectrophotometric method which represents the ultimate in sensitivity, precision, and accuracy. On review, the best methods for copper appeared to be optical absorption without

Jan 1, 1969

By Charles M. Packer, Oleg D. Sherby, Roy H. Johnson

Originally round tensile specimens of a eutectic Zn-A1 alloy develop elliptical cross sections during superplastic deformation. This observation, coupled with a detailed study of the microstructure and preferred orieniation, suggests that crystallographic slip and continuous grain boundary migration or re-crystallization are important processes during super-plastic deformation. In spite of the extensive activity in superplasticity1-15 and the numerous explanations proposed, no single model has had universal acceptance. It has been established, however, that the general requirements for superplastic extension of two-phase alloys include an extremely fine, stabilized grain size of the order of a few microns, a temperature about equal to or greater than one-half the melting point, a critical range of strain rate, and a similarity in the mechanical strength of the major phases. The proposed models can perhaps best be characterized in terms of the important phenomena associated with them. These phenomena include: phase instability,1 diffusional creep by volume diffusion3 or grain boundary diffusion4,5 slip and continuous grain boundary migration or recrystalliza-tion,= grain boundary Sliding,7-9,13,14 and dislocation glide.&apos;5 In this paper, experimental observations will be reported which support a model involving slip and continuous grain boundary migration or recrystalliza-tion. Specifically, a correlation will be made between this model and the development of elliptical cross sections as originally round specimens are superplas-tically deformed. For the most part, superplasticity studies have been conducted with eutectic or eutectoid alloys. Probably the most thoroughly studied material has been the monotectoid Zn-A1 alloy.1,2,6,12,13,15 No attention to the eutectic Zn-A1 alloy has previously been reported, and the results discussed in this paper represent part of a general study of the superplastic properties of this alloy. MATERIALS The alloys used in this investigation were prepared by melting appropriate quantities of 99.99+ pct A1 and 99.999 pct Zn in air, mixing, and pouring into a water- cooled stainless-steel mold. Wet-chemical analysis was conducted with each heat of alloy prepared, using the procedure of Fish and smith.16 The composition of the eutectic alloy was 95.1 wt pct Zn. Ingots about 2 in. thick were rolled to 0.4-in. plate at about 300°C with a reduction of 5 to 10 pct per pass. Specimens were machined from the plate with the tensile axis parallel to the rolling direction. The specimens were round, with 0.150-in.-diam, 1.25-in.-long gage length, and 0.25-in.-diam threaded grip sections. EXPERIMENTAL PROCEDURE Specimens were mounted inside a uniform-temperature quartz tube which was surrounded by a double elliptical radiant furnace with a 12-in.-long uniform-temperature hot zone and a low thermal capacity. The tube extended through the top and bottom of the furnace and permitted rapid quenching of the loaded specimens when quickly filled with cold water at the conclusion of the test. The quench precluded any effects on specimen microstructure from a normal, slow cool. Constant stress was applied to test specimens by suspending a load on a constant stress cam of the type described by Hopkin.17 The design of this cam permitted application of a constant stress for elongations up to 200 pct. For greater elongation, approximately constant stress conditions were maintained by systematically reducing the load manually. RESULTS As part of an investigation of the superplastic properties of the eutectic Zn-A1 alloy, evidence was obtained for the development of elliptically shaped cross sections as originally round specimens were extended. For example, after an elongation of about 100 pct, a round specimen with an initial diameter of 0.150 in. became elliptical with major and minor axis of 0.128 and 0.88 in., respectively. Photographs are presented to illustrate the ellipticity developed during superplastic deformation, Fig. 1. The specimen shown was deformed at a stress of 500 psi, at a temperature of 285°C, and a strain rate of 2.28 x 10-2 min-1. The strain-rate sensitivity exponent* was measured at *The strain-rate sensitivity exponent, m, is defined as d In o/d In c where o is the steady-state flow stress and E is the strain rate. this temperature and in the strain rate range 10"3 to 10-1 min-1 was found to be about 0.5. This value is typical of those observed with superplastic materials. The material studied exhibited negligible strain hardening during superplastic deformation, the creep rate remaining constant under constant stress and temper-

Jan 1, 1969

By William C. Harrigan, William D. Nix

Dynamic measurements of Young&apos;s modulus have been made for poly crystalline Ni-W alloys from room temperature to 800°C. The alloys studied range in composition from pure nickel to Ni-10 at. pct W. The results indicate that Young&apos;s modulus decreases linearly with temperature above the Curie temperature. The rate of change of Young&apos;s Modulus with temperature mas found to range from 104 psi per "C for pure nickel to 0.82 x 104 psi per °C for Mi-10 pct W. At all temperatures the elastic modulus decreases with increcrsing tungsten content up to 1 at. pct W, and increases as the tungsten content is increased above that level. Young&apos;s modulus decreases slightly as the carbon content is increased from 0.002 to 0.09 wt pct C THE knowledge of the elastic modulus of metals and alloys is important for a number of reasons. The first and most obvious reason comes from the need to predict elastic deflections under given loading conditions. A second and somewhat more subtle reason comes from the fact that the elastic properties of an alloy must be known before a proper account of the mechanisms of plastic deformation can be made. This is especially true for high-temperature creep of crystalline solids. Sherby and his coworkers have shown that the high-temperature steady-state creep rates of crystalline solids are inversely related to the elastic modulus1,2 and that the temperature dependence of the elastic modulus must be taken into account if reliable determinations of the activation energy for creep are to be made. In addition, measurements of the elastic constants of solid solutions are needed to allow one to assess the modulus interaction contribution to solid-solution Strengthening.3-5 Pelloux and Grant6 have demonstrated that substantial solid-solution strengthening at room temperature and elevated temperatures occurs when refractory metal solute atoms are added to nickel. While the high-temperature elastic properties of pure nickel have been measured by a number of authors,7-10 the elastic properties of nickel-based refractory metal alloys have not been determined. The purpose of this paper is to report on measurements of Young&apos;s modulus of polycrystalline Ni-W alloys at elevated temperatures. It is expected that these measurements will be valuable to studies of the mechanical properties of nickel-based refractory metal solid solutions. I) EXPERIMENTAL Young&apos;s moduli of polycrystalline samples were determined by a dynamic method in order to reduce high- temperature anelastic and plastic relaxations. The samples were forced in transverse free-free vibration; that is, both ends of the sample were unrestrained and the vibration was transverse to the long axis. The fundamental resonant frequency was determined by the Forster method.11 The analysis of this type of vibration which was formulated by Rayleigh,12 Timo-chenko,13 and pickett,14 and reviewed by Fine," leads where fn is the resonant frequency of the nth mode, r is the radius of the circular cross section. L is the specimen length, ßn is 1.5056 for free-free vibration in the fundamental mode of vibration, 6 is the mass density, and E is Young&apos;s modulus in the axial direction. This equation can be transformed into: E = 9.17605 x 10-6(L/D)E/Lf2 [2] where E is Young&apos;s modulus in psi, L is the length in inches, d is the diameter in inches, W is the weight in grams, and f is the resonance frequency in cps. Eq. [2] was further modified in order to take account of the thermal expansion of the samples. The resulting correct term is: where the thermal expansion coefficients for nickel and tungsten, respectively. Xw is the atom fraction of tungsten in the sample and T is the temperature in "C. The treatment of the thermal expansion coefficient as a linear function of composition seems sufficiently accurate since an error of 25 pct in the expansion coefficient will result in only a 0.3 pct error in the modulus at 1000°C. A) Apparatus. The equipment for this investigation has been described by Lytton et al.16 Several modifications of the equipment have been made. The most significant change involved replacing the detector crystal transducer with a magnetic transducer. A phonographic magnetic transducer was employed as a sensing device since the contact pressure necessary to produce a stable signal is much less than that for a crystal transducer. This magnetic transducer is also not affected by conditions of high temperature and vacuum which are present in these experiments. The vacuum was 10-5 torr at room temperature and about 5 x 10-4 torr at 900°C. This was sufficient to prevent surface contamination of the samples during the tests. The samples were heated in an elliptical furnace with a quartz lamp at one focal line and the sample at the other, as described by Lytton et a1.16 The temperature of the sample was measured by monitoring the

Jan 1, 1969

By Robert D. Pehlke, Robert G. Blossey

The solubility of nitrogen in liquid iron alloys containing chromium and nickel has been measured in the temperature range 1550° to 1700°C at nitrogen pressures to 1 ah. The solubility surface has been determined for the iron corner of the liquid metallic ternary to 21 pct Cr and 11 pct Ni. The nitrogen solubility increases markedly with increasing chromium concentration. The effect of nickel and the bilinear effect of chromium and nickel are less pronounced. The solubility data are presented, and interaction coefficients are determined from them. THE solubility of nitrogen has been determined in liquid Fe-Cr-Ni binary and ternary alloys. The work in this laboratory has been directed toward a relatively limited composition range, that is to 20 pct Cr and 10 pct Ni. Humbert and Elliott1 studied the entire ternary; but their investigation was, understandably, limited in this region. The region considered here is of the greatest commercial interest. Knowledge of the solubility in these alloys is important for accurate control of the nitrogen levels in various stainless alloys. Also, the solution behavior is of theoretical interest because of its deviations from ideal dilute solution rules at moderate chromium levels. The nitrogen solubility in the iron binaries has been reviewed extensively by Pehlke and Elliott,2 particularly with respect to the dilute solution interaction parameters. More recently, there has been some interest in accurate descriptions of solute interactions in non-dilute solutions. Most of the investigators have adopted a power series fit to accommodate any non-linearity of the data. The Taylor series expansion is adopted here, using Scimar&apos;s notation3 for the interaction coefficients. An alternate method, instead of requiring higher-order expansions, is to restrict the range of the composition variables. A planar solubility surface may be fitted to the data and its range of validity determined. If the axes of this region are displaced from the usual origin—the solvent pure iron—a change in standard state is required for the solution reaction. The standard state for nitrogen in iron is commonly taken as the hypothetical 1 wt pct solution of nitrogen in pure iron. However, for an alloy of appreciable solute concentration, e.g., 13 pct Cr or 18 pct Cr-8 pct Ni, it would be convenient to use that base composition as the solvent and redefine the solution reaction in terms of that particular solvent. A brief derivation follows, defining the free energy of solution in an alloy solvent. Following the treatment by Darken and Gurry,4 for a nitrogen pressure of 1 atm: N (pure component) = N (1 wt pct in solvent) [l] AG=RT ln100/ wt pct N in solvent Taking this reaction for an alloy solvent less the same reaction for a pure iron solvent the relation between nitrogen in pure iron and an alloy is: N (1 wt pct in Fe) = N (1 wt pct in alloy) [2] AG = RT[ln(wt pct N in Fe) - ln(wt pct N in alloy)] Adding ½ N2(g) to each side and subtracting N (1 wt pct in Fe) = ½N2(g), the total free energy for solution of nitrogen in an alloy, referred to nitrogen at infinite dilution, is given by: ½N2 (g) = N (wt pct in alloy) L3] AG°3 = -RT ln(wt pct N in alloy )PN =1 atm Interaction parameters have their usual meaning when ?G°/RT is differentiated with respect to the proper composition coordinate. If desired, the dilute alloy treatment may be utilized with the new reference composition as the solvent. This has. indeed, been done by Small and pehlke5 in their analysis of nitrogen solution in liquid 18-8 alloys. The Sieverts&apos; technique was used for this investigation on an apparatus previously described.6 The materials used in this program were: Ferrovac-E iron, 99.95 pct, Crucible Steel Co.: chromium, 99.95 pct, Union Carbide Metals Co.; nickel, 99.9 pct, International Nickel Co. Recrystallized alumina crucibles were used with no evidence of crucible-melt reaction. RESULTS The locations of the ternary compositions investigated are shown in Fig. 1. The data of Turnock7 and small8 have been alluded to in other papers.5&apos;6 There were no departures from Sieverts&apos; law observed for

Jan 1, 1969

By J. C. Williams, M. J. Blackburn

Several of the decomposition processes that can occur in supersaturated phases in a Ti:11.6 wt pct Mo and a Ti:20 wt pct V alloy have been studied by transmission electron microscopy. The deformation induced "marternsitic phase" in the Ti:Mo alloy has been found to have a bcc or bct structure rather than the previously reported hexagonal structure. The morphology of&apos; the transformed region is a rather complex asserrlblage of twins, twinning occurring in one or more systems; this internal twinning has been found to occur on (112). The w phase is formed in both alloys on aging and is present in the Ti:Mo alloy after quenching. The structure of this phase has been confirmed as hexagonal in both systems, however, differences in morphology and stability are found between the two alloys. Thus in the Ti-Mo alloy the w phase has an ellipsoidal morphology with the major axis lying parallel to <111>ß or [0001]w while in the Ti-V alloy the phase forms as cubes, the cube faces lying parallel to {100}ß or {2021}w Some observations on the particle sizes, volume fraction, and composition of the w phase in the Ti-Mo alloy are listed. The mode of formation of The a phase from the (ß + w) structures is also different in the two alloys. In the Ti-Mo alloy the a phase is formed by either a cellular reaction or by the growth of isolated needles, whereas in the Ti-V alloy the a phase is nucleated at an w:ß interface and grow to consume the w phase. Some of the difjerences in behavior of the w phase are attributed to the mismatch between it and the solute enriched ß matrix in which it forms. MaNY transition elements tend to stabilize the bcc or ß-phase when added to titanium. In general two types of phase diagrams are produced, either a ß-stabilized (ß-isomorphous) system, e.g., Ti:Mo, -Ti:V, Ti:Nb, or a ß-eutectoid system, e.g., Ti:Cr, Ti:Fe, Ti:Mn. In previous papers&apos;-4 the phase transformations in the a-phase and (a + ß)-phase alloys have been described and this work has been extended to ß-stabilized systems. Specifically, transformations in the alloys Ti:20 wt pct V and Ti:11.6 wt pct Mo have been studied; in both of these alloys the ß phase is retained at room temperature when quenched from the ß-phase field. A number of phase transformations can occur in such metastable ß phases and the two alloys were chosen to include most of the transformations reported for ß-stabilized systems. We list these possible phase transformations below. Ti:11.6 Mo quenched from >780°C to retain the ß phase: a) The w phase can form on quenching.5 b) Martensite can be produced by subzero cooling or deformation. Two martensite habit planes have been reported in Ti:Mo alloys; (334)ß and (344)ß=6 c) On aging at temperatures <-550° C the w phase is formed before the a-phase.5,7 d) On aging at temperatures >550°C the a phase is formed.7 e) The martensite can be tempered. It has been reported that the a phase rather than the ß phase is precipitated during tempering.&apos; Ti:20V quenched from >660°C to retain the ß phase:9 a) At aging temperatures <260°C separation into two bcc phases occurs. b) The w-phase is produced prior to the a phase on aging at temperatures <-400°C. c) At temperatures 2400°C the a phase is formed directly. T-T-T diagrams describing the temperature and time regimes for the formation of these phases have been published7,9 for a Ti:12 pct Mo and a Ti:20 pct V alloy. We have attempted to investigate these transformations using transmission electron microscopy, however thin foils undergo a spontaneous transformation in all conditions except the equilibrium (a + ß) structure. This transformation has been reported previ0usly10,11 and we will comment on its morphology and nature in the various sections of experimental results. EXPERIMENTAL The compositions in wt pct of the two alloys investigated were: Ti:11.6 Mo, 0.100 02, 0.006 N2, 0.0015 H2 Ti:20V, 0.0574 O2, 0.0111 N2, 0.005 H2 These alloys were cold-rolled to 0.020 in. thick sheet. Specimens were heat treated in vacuum or in inert gas at temperatures >500°C and in a circulating air furnace at temperatures <500°C. Thin foils were prepared using standard techniques, described in detail previously." Dark field micrographs were obtained using high resolution technique. RESULTS Martensitic Transformation in Ti:11.6 pct Mo. Detailed study of the deformation induced martensite is not possible due to a spontaneous transformation which occurs near the edge of thin foils as shown in Fig. 1. Similar transformations have been observed in iron-" and copper-base13 alloys as well as other titanium alloys, but some observations specific to the Ti:1l.6 Mo alloy are listed below. a) The boundaries of these transformed regions are glissile and move under the influence of the electron beam during examination. b) Selected area diffraction indicates the transformed regions have the same structure as the matrix, being separated by tilt boundaries. The misori-

Jan 1, 1969

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By C. G. Bieber, J. R. Mihalisin, R. T. Grant

A growing demand for longer service life of gas turbines has placed increasingly rigorous requiret~rents upon superalloys employed for that application. Long-titne testing at high temperature has revealed that phase transformations occur in all superalloys. A common one of particular interest is o formation. Presented here are studies made to identify a and to characterize its formation and effect on properties in three cast nickel-base superalloys—IN 100 alloy, alloy 713C, and alloy 713LC. Methods are discussed by which o can be eliminated or inhibited in IN 100 alloy and alloy 713C. Evidence was obtained to indicate that some types of o may be more detrimental than others. Limitations in the electron vacancy approach to o prevention are pointed out, and it is shown how alternative approaches, such as reducing a complex superalloy matrix to the form of a pseudo-ternary system permitting equilibrium diagram treatment, lead to additional insights into the formation of in these alloys. AROUND 1960. Beiber1 developed IN 100 alloy, which still remains one of the strongest commercially available nickel-base superalloys. The principle used in the design of this alloy was to produce large quantities of y&apos; phase in a y matrix through the use of copious amounts of aluminum and titanium. In 1963, ROSS&apos; showed that when certain heats of this alloy were held for a long time at 1650°F they formed an acicular phase, subsequently identified as a.3 a is a hard and brittle phase first discovered in the Fe-Cr system by Bain and Griffiths.4 They termed it the "B" constituent. Subsequently this same phase was found in other systems, primarily those of the transition elements, and acquired the name "a" by which it is now known. The crystal structure of the a phase was first determined in the Fe-Cr system in 1950.5 It was shown to be tetragonal with a c/a ratio of about 0.52. as is the case with a found in other systems. This characteristic crystal structure is now the means by which a is identified. In superalloys, such as IN 100 alloy. large amounts of o impair the high-temperature creep strength and drastically reduce room-temperature tensile ductility. Discovery of o phase in some heats of IN 100 alloy quickly led to investigations of other superalloys for similar transformations. It was found that many of the stronger, more highly alloyed. super-alloys were indeed susceptible to o formation. This investigation has been concentrated on three commercial alloys: IN 100 alloy, alloy 713C, and alloy 713LC. J.R.MIHALISIN,MemberAIME, and C.G.BIEBER are with The International Nickel Co., Inc., Paul D. Merica Research Laboratory, Sterling Forest, Suffern, N. Y. R. T. GRANT, Member AIME, is with The International Nickel Co., Inc., Pittsburgh, Pa. Manuscript submitted May 22. 1968. IMD A detailed study has been made of the phase transformations and their relation to a formation along with a consideration of electron vacancy approaches for predicting a-forming propensity in these alloys. EXPERIMENTAL PROCEDURE Phase transformations were studied by light and electron microscopy, electron diffraction, microprobe investigations, and X-ray diffraction. Specimens for light micrographic examination were prepared by conventional grinding and polishing followed by etching with glyceregia (2:l HC1/HNO3 + 3 glycerine by volume). Photomicrographs of stress-rupture specimens were taken adjacent to the fracture unless otherwise noted in the text. Negative replicas for electron microscopy were taken from surfaces electropolished with a solution of 15 pct H2SO4 in methanol. For carbon extraction replication, a solution of 10 pct HC1 in methanol was used. A Siemens Elmiskop I was used for all electron microscopy. Selected-area diffraction studies were made at 80 kv using evaporated aluminum for standardizing the patterns. A nondispersive electron microprobe attachment was used to analyze the extracted precipitates chemically. The fluorescent X-rays were recorded using a flow counter containing P10 gas (90 pct Ar-10 pct methane) with a beryllium window and a single-channel pulse-height analyzer. The pulses from the analyzer were passed to a scaler-ratemeter and differential curves of counting rate vs pulse amplitude were obtained. The base line of the analyzer was driven with a synchronous motor at 0.5 v per min and a channel width of 0.5 v. The time for 105 counts was printed out for each 0.5-v increment. The microscope was operated at 80 kv with beam currents of 1 to 20 pa. This equipment detects elements from atomic number 13 to 40. X-ray diffraction studies were usually made on residues electrolytically extracted in 10 pct HC1 in H2O, although in one case a pattern was obtained from an etched surface of a metallographic specimen. A Siemens Crystalloflex IV was used with iron-filtered CoKa radiation. X-ray patterns were recorded using a goniometer speed of : deg per min. The scintillation counter and pulse-height analyzer operated at a channel height of 10 v and a channel width of 12 v. The equipment was calibrated with a powdered gold standard. The residues usually contained a number of phases. several of which could not be found in the ASTM card file. In addition, as is shown for the case of a phase in IN 100 alloy, other phases had a somewhat different lattice parameter from that reported in the ASTM card file, making it difficult to separate and identify constituents by comparison with ASTM d spacings. For these reasons, phases were identified on the basis of the lattice parameter obtained by indexing the ob-

Jan 1, 1969