Search Documents

By C. T. Wei, A. Kelly

USING a recently developed X-ray method, reported by Schulz,2 it is possible to make a rapid survey of the perfection of a single crystal at a particular surface. This technique has the advantage of allowing a large surface of a specimen to be examined by taking a single photograph and it compares well with other X-ray methods in regard to sensitivity of detection of small angle boundaries. During the course of a survey of the perfection of large crystals of aluminum produced by a number of methods, an examination has been made of a number of single crystals produced from the melt using a soft mold (levigated alumina)." Crystals grown by this method are known, from an X-ray study carried out by Noggle and Koehler,3 to contain regions where they are highly perfect. In the present work, it has been possible to obtain photographs showing directly the distribution of low angle boundaries at a particular surface of these crystals. single crystals were grown from the melt using the modified Bridgman method with a speed of furnace travel of -1 mm per min. These were about 1/10 in. thick, 1 in. wide, and several inches long. The metal was 99.99 pct pure aluminum supplied by the Aluminum co. of America. The crystals were examined by placing them at an angle of about 25° to the X-ray beam issuing from a fine focus X-ray tube of the type described by Ehrenberg and Spear4 and constructed by A. Kelly at the University of Illinois. A photographic film was placed SO as to record the X-ray reflection from the lattice planes most nearly parallel to the crystal surface. The size of the focal spot on the X-ray tube was between 25 and 40 u, and the distance from the X-ray tube focus to the specimen (approximately equal to the specimen to film distance) was -15 cm. White X-radiation was used from a tungsten target with not more than 35 kv in order to reduce the penetration of the X-rays into the specimen. Exposure times were approximately 1 hr with tube currents between 150 and 250 microamp. The type of photograph obtained from these crystals is illustrated in Fig. 1, which shows a number of overlapping reflections from the same crystal. The large uniform central reflection is traversed by sets of horizontal white and dark lines. These two sets run mainly parallel to one another. Lines of one color are wavy in nature and often branch and run together. Large areas of the crystal surface show no evidence of these lines whatsoever. The lines are interpreted as being due to low angle boundaries in the crystal, separating regions which are tilted with respect to one another. A white line is formed when the relative tilt forms a ridge at the interface and a black line is found when a valley is formed. In a number of cases, the lines stop and start within the area of the reflection and often run into the reflection from the edge, corresponding to a low angle boundary starting from the edge of the crystal. The prominent lines run roughly parallel to the direction of growth of the crystal although narrow bands can run in a direction perpendicular to this; see Fig. 2. Although they may change their appearance slightly, the lines tend to occur in the slightly,Same place in the X-ray image and to maintain their rough parallelism when the crystals are reduced in thickness by etching. Thus the low angle boundaries can occur at any depth within the crystal. The appearance of the lines is unaffected by subjecting the crystal to rapid temperature changes, such as plunging into liquid nitrogen or rapid quenching from 620°C. From the width of the lines on the x-ray reflection, values can be found for the angular misorienta-tion of the two parts of the crystal on either side of a boundary. The values found run from 1' to 10' of arc, but values of UP to 20' have sometimes been found, e.g., the widest lines on Fig. 2. These mis-orientations are much less than those commonly found in crystals possessing a lineage structure. When a number of a and white lines occur, running in a roughly parallel direction across the image of a Crystal, the total misorientation corresponding to lines of one color is approximately equal to that corresponding to lines of the other color. The interpretation of the lines as due to low angle boundaries has been checked in a number of ways. Photographs taken with different specimen-to-film distances distinguish lines due to low angle boundaries from effects due to surface relief of the specimen. Normal Laue back-reflection photographs, taken with the beam irradiating an area of the surface showing a number of the lines, show white lines running through each Laue spot. Black lines are set to see by this method. X-ray photographs were also taken, using the set-up described by Lam-one et al.5 when the beam straddles regions giving rise to lines in the Schulz pattern, split reflections are observed within the Bragg spot. The misorienta-tions calculated from the separation of these reflections and that found from the widths of the lines on the schulz technique patterns show good agreement. An exposure was made with Lambot technique of an area of the crystal showing no evidence of low angle

Jan 1, 1956

By M. R. J. Wyllie, F. Morgan, P. F. Fulton

The importance of formation factor, F, not only in electric logging but as a fundamental rock parameter has recently been stressed.',: The desirability of investigating the range of variation of the resistivity index exponent, n, in the relationship I = S ;", where I is the resistivity index and Sw the water saturation as a fraction of the void volume of a porous medium, has also been urged.3 The magnitude and variation of n with saturation and rock texture is a subject not only of theoretical interest but also one of prime importance in the interpretation of electric logs. A simple technique has recently been developed which enables both F and u to he measured with high accuracy and which may also find acceptance as a convenient method for the determination of irreducible saturation attainment in the restored state method of core analysis. Experience has taught that reproducible measurements of F are possible only if the resistance measuring electrodes are so arranged with respect to a plane face on a porous medium that they are able to make electrical contact with substantially all entry pores in that plane. In practice this may be achieved by using a platinized-platinum gauze electrode backed by some absorbent material (such as felt) which has been saturated with a fluid identical with that used to saturate the porous medium. Applicatiorl of pressure to the electrode and absorbent material then forces the gauze against the plane face of the porous medium and simultaneously squeezes saline solution through the meshes of the gauze. By this means the electrode is in continuous aqueous contact with all pores and satisfactory and reproducible low resistance contact with the porous medium is achieved. Clearly this method, although satisfactory for measurements of F, cannot be applied to the making of continuous resistance measurements on a porous medium while capillary pressure desaturation is being carried out. However, accepting the principle that for satisfactory results electrical contact must be made between a measuring electrode and all pores adja- cent to that electrude, methods of bringing electrodes into intimate contact with the surfaces of porous media were investigated. Two methods were ultimately found to be satisfactory: in the one, the metal electrode is formed on the required portion of the porous medium by the use of a metal spray gun, while in the second the electrode is painted on with an ordinary camel's hair brush. The first method has the advantage of permitting the use of any metal which can be sprayed, but has the disadvantage of requiring rather elaborate and expensive equipment. The second method is presently limited to silver electrodes although in principle other metals, e.g. platinum or gold, could be used. Moreover, the method is so simple and cheap, and has been found to be so satisfactory that it will be described in some detail. The core being investigated is cut into a right circular cylinder and is extracted and dried in the usual manner. The ends are then lightly painted with silver conducting paint* of the type used in printed electrical circuits. The quantity of paint used is not critical but the recommended, minimum compatible with entirely coating the core ends is recommended, particularly on the end that contacts the barrier. The core is then dried at atmospheric temperature for one hour or for shorter periods at any suitable elevated temperature up to about 110°C. It will be found that silver coatings so prepared are not only strongly adherent but also permeable and the core may be the core may be desaturated by the ordinary capillary pressure technique through one of the coated faces. The same permeability is characteristic also of thin metal coatings formed using the spray-gun technique. An ordinary Lucite capillary pressure desaturation cell has been adapted to a form suitable for measuring the resistivity of the saturated silver faced cores both at 100 per cent saturation (i.e., F) and at intermediate saturations down to the irreducible minimum. This has been achieved as follows: A Coors porcelain barrier, having a displacement pressure of c 30 psi was grooved across a diameter. Dimensions of this groove were c 1 mm deep and 1 mm wide at the top. The groove was then painted thickly with silver conducting paint, the paint in the groove being extended lightly over the edges of the groove for a distance of c 1 mm on each side. A 30 gauge silver wire was then arranged in the groove in a form of a spring bow, each end of the silver being held at diamet~ically opposite ends of the groove by means of plastic cement. The arc of the bow at its highest point was arranged to be a millimeter or so above the face of the barrier, while one end of the bow wire was led by means of a pressure-tight connection through the wall of the capillary pressure cell. The groove in the barrier was then Surrounded by suitably cut portions of Kleenex in the conventional manner so as to ensure capillary continuity from core to barrier, and the core placed on the barrier. The weight of the core distorted the silver spring bow and good electrical contact was thereby made between the outside of the cell and the lower painted silver electrode. Electrical connection to tile top painted silver

Jan 1, 1951

By M. R. J. Wyllie, F. Morgan, P. F. Fulton

The importance of formation factor, F, not only in electric logging but as a fundamental rock parameter has recently been stressed.',: The desirability of investigating the range of variation of the resistivity index exponent, n, in the relationship I = S ;", where I is the resistivity index and Sw the water saturation as a fraction of the void volume of a porous medium, has also been urged.3 The magnitude and variation of n with saturation and rock texture is a subject not only of theoretical interest but also one of prime importance in the interpretation of electric logs. A simple technique has recently been developed which enables both F and u to he measured with high accuracy and which may also find acceptance as a convenient method for the determination of irreducible saturation attainment in the restored state method of core analysis. Experience has taught that reproducible measurements of F are possible only if the resistance measuring electrodes are so arranged with respect to a plane face on a porous medium that they are able to make electrical contact with substantially all entry pores in that plane. In practice this may be achieved by using a platinized-platinum gauze electrode backed by some absorbent material (such as felt) which has been saturated with a fluid identical with that used to saturate the porous medium. Applicatiorl of pressure to the electrode and absorbent material then forces the gauze against the plane face of the porous medium and simultaneously squeezes saline solution through the meshes of the gauze. By this means the electrode is in continuous aqueous contact with all pores and satisfactory and reproducible low resistance contact with the porous medium is achieved. Clearly this method, although satisfactory for measurements of F, cannot be applied to the making of continuous resistance measurements on a porous medium while capillary pressure desaturation is being carried out. However, accepting the principle that for satisfactory results electrical contact must be made between a measuring electrode and all pores adja- cent to that electrude, methods of bringing electrodes into intimate contact with the surfaces of porous media were investigated. Two methods were ultimately found to be satisfactory: in the one, the metal electrode is formed on the required portion of the porous medium by the use of a metal spray gun, while in the second the electrode is painted on with an ordinary camel's hair brush. The first method has the advantage of permitting the use of any metal which can be sprayed, but has the disadvantage of requiring rather elaborate and expensive equipment. The second method is presently limited to silver electrodes although in principle other metals, e.g. platinum or gold, could be used. Moreover, the method is so simple and cheap, and has been found to be so satisfactory that it will be described in some detail. The core being investigated is cut into a right circular cylinder and is extracted and dried in the usual manner. The ends are then lightly painted with silver conducting paint* of the type used in printed electrical circuits. The quantity of paint used is not critical but the recommended, minimum compatible with entirely coating the core ends is recommended, particularly on the end that contacts the barrier. The core is then dried at atmospheric temperature for one hour or for shorter periods at any suitable elevated temperature up to about 110°C. It will be found that silver coatings so prepared are not only strongly adherent but also permeable and the core may be the core may be desaturated by the ordinary capillary pressure technique through one of the coated faces. The same permeability is characteristic also of thin metal coatings formed using the spray-gun technique. An ordinary Lucite capillary pressure desaturation cell has been adapted to a form suitable for measuring the resistivity of the saturated silver faced cores both at 100 per cent saturation (i.e., F) and at intermediate saturations down to the irreducible minimum. This has been achieved as follows: A Coors porcelain barrier, having a displacement pressure of c 30 psi was grooved across a diameter. Dimensions of this groove were c 1 mm deep and 1 mm wide at the top. The groove was then painted thickly with silver conducting paint, the paint in the groove being extended lightly over the edges of the groove for a distance of c 1 mm on each side. A 30 gauge silver wire was then arranged in the groove in a form of a spring bow, each end of the silver being held at diamet~ically opposite ends of the groove by means of plastic cement. The arc of the bow at its highest point was arranged to be a millimeter or so above the face of the barrier, while one end of the bow wire was led by means of a pressure-tight connection through the wall of the capillary pressure cell. The groove in the barrier was then Surrounded by suitably cut portions of Kleenex in the conventional manner so as to ensure capillary continuity from core to barrier, and the core placed on the barrier. The weight of the core distorted the silver spring bow and good electrical contact was thereby made between the outside of the cell and the lower painted silver electrode. Electrical connection to tile top painted silver

Jan 1, 1951

By J. Lewis, J. Harper, M. F. Ashby

A grain boundary in a metal interacts with second-phase particles, which exert a pinning force (first estimated by Zener) on the boundary opposing its motion. We have computed the shape of boundaries which interact with more or less spherical second-phase particles and have constructed a soap-film model to reproduce the shape of the boundary surface. An important result is that measurement of this shape allows the pressure, or driving force, on the boundary to be measured. We hare applied this technique to grain boundaries in two alloys and hate measured the pinning force exerted by single second-phase jwrticles on the boundaries. It is in good agreement with Zener's estimate. J\. boundary between two grains, or two bulk phases, interacts with small inclusions or particles of a second phase, whether they are gas or solid. This interaction means that the boundary, forced to migrate by a difference in free energy between the material of the two grains or phases which it separates, exerts a force on a particle which it touches, tending to drag it forward. (The movement of inclusions through metals under the influence of this force, has, in fact, been observed. 1-3) Equally, the particle can be thought of as exerting a pinning force on the boundary, tending to hold it back. Zener (in a celebrated private communication4) first realized that this interaction, and the resulting pinning force, existed. His calculation of its magnitude was crude but adequate: a spherical inclusion of radius r blanks off an area nr2 of the boundary on which it sits; since the boundary has an energy of rMM x per unit area, the blanlung-olf decreases the energy of the system by MM: this energy is returned to the system if the boundary is pulled free from the inclusion— a forward movement of the boundary by a distance r will do this—so that the maximum pinning force is Trrym.M- A similar argument can be made for inter-phase boundaries. The nature of the particle itself did not enter this, or two subsequent treatments.5,6 When it is considered, tic leifthe energyoftheb a) The boundary may enter and pass through the particle if the energy of the boundary is lower within the particle than in the matrix. Fig. l(r/). Certain coherent precipitate particles behave like this. h) More usually, the boundary will bend round the particle, enveloping and bypassing it. Fig. l(b). In doing so, it changes the structure and energy of the interface between the particle and its matrix. This means that the boundary does not touch the particle surface at right angles, as early treatments assumed,5'9 but at some angle a which depends on this change in surface energy of the particle, and can be calculated from the equilibrium of surface tensions. Most precipitate particles and inclusions behave like this. Gas bubbles or liquid drops can be regarded as belonging to either group. The progress of bypassing is conveniently measured by the angle shown in Fig. 1. When the nature of the particle is ignored, its maximum pinning force is exerted when - 45 deg. When it is considered, this critical value of is found to depend on a and thus on the nature of the particle. The maximum pinning force lies between nryMM and 2jtjMM (Appendix 1). not very different from Zener's result. In reality, a boundary between crystals has a specific energy and tension which varies with the orientation of the boundary. Furthermore, recent experiments7 indicate that such a boundary is not atom-ically smooth, but has steps on it: migration of the boundary corresponds to the sweeping of these steps across the boundary surface, like the Frank model of crystal growth from the vapor. This means that the interaction of a boundary with particles should really be considered in terms of the way in which particles hinder the movement of these steps. To suppose a grain boundary or interphase boundary to be smooth, and to ignore the variation of its energy with orientation, is to liken it to a soap film. The advantage of this soap film approximation, which we have used throughout this paper, is that interaction energies and boundary shapes can be calculated easily. We have done this by numerical computation and by using a soap film model, and have compared the results with grain boundaries in an aluminum-based and a copper-based alloy. It turns out that the shape of the boundary which bulges between particles allows the pressure an it to be calculated; that is, the local driving force an the boundary can be measured. This has allowed us to check the Zener relationship experimentally.

Jan 1, 1970

By H. W. Meyer, H. N. Lander, F. D. Delve

A method of calculating the changes in blast-furnace performance brought about by burden and/or blast modifications is presented. Essentially the method consists of three simultaneous equutions derived from materials and heat balances. These equations can be used not only to evaluate quantitatively the effect of changes in process operating variables on furnace performance, but also to provide a useful means of evaluating changes in process variables which cannot be measured directly. It has been customary for a number of years to use simple heat and materials balances as a basis for assessing blast-furnace practice. A good example of the method used to set up these balances is that proposed by Joseph and Neustatter.1 This approach to process assessment has limited utility, however, in that it cannot be used to predict the furnace coke rate or production under new operating conditions. Using an approach based on multiple correlation of blast-furnace variables, R V. Flint2 has developed an equation which may be used to predict the change in coke rate that will result from some changes in operating conditions with a reasonable degree of accuracy. Although this equation has useful applications in production planning, it cannot be used to study the relationships between the operating variables and the fundamental thermochemi-cal characteristics of the process. In attempting to analyze the blast-furnace process quantitatively, the idea of dividing the furnace into zones3 may at first appear attractive. In our present state of knowledge, however, it is not possible to define with any accuracy the physical limits of such zones in relationship to their temperatures or to the reactions which may occur in them. Although its application is restricted, the zonal approach to blast-furnace analysis is useful in some instances. For example, the change in the calculated flame temperature in the "combustion zone" caused by injecting steam constitutes information which is helpful in understanding why the addition of steam to the blast is best accompanied by an increase in blast temperature. The zonal approach cannot, at the present time, be used to establish the relationships between process variables and process performance if the whole process rather than part of it is to be considered. One of the earliest approaches to the problem of relating blast-furnace operating variables to pro- duction and coke rate was that developed by Marshall.4 Essentially Marshall's work showed that it was possible to estimate the performance of a furnace by solving three simultaneous equations which consisted of rudimentary carbon and heat balances plus a further equation relating the production, wind rate, and the carbon burned at the tuyeres. Although these equations did not include all of the chemical and thermal variables of the process, their derivation and application seems to be the earliest attempt which achieved any success in relating prior furnace operating data to the calculation of furnace performance under different blast conditions. Work carried out in Germany has been directed mainly towards prediction of coke rates using material and thermal balances rather than statistical methods. wesemann5 used prior furnace operating data as part of the basis for predicting the change in coke rate accompanying a change in burden composition. This author employed a method of successive approximations to estimate the secondary changes in slag volume and stone rate brought about by the change in coke rate. The most recent analysis, which seems to have been developed concurrently with the thermochemical model presented in this paper, has been described by Georgen.6 This author has succeeded in improving on Wesemann's approach by expressing the total changes in the slag volume and stone rate in terms of the change in coke rate itself. This is accomplished in a manner similar to that used in the thermochemical model described in this paper. Although Georgen makes use of a calculated furnace heat loss, he does not relate the heat loss per unit of hot metal to the production rate as is done in the present work. Georgen's approach may be used to calculate the changes in materials requirements accompanying changes in furnace operation; it cannot be used to assess the resulting changes in production. The fact that blast-furnace behavior can be interpreted by consideration of the heat requirements of the process was demonstrated by Dancy, Sadler, and Lander.7 In the analysis of blast-furnace operation with oxygen and steam injection these authors showed that it was possible to account for the changes in production and coke rate

Jan 1, 1962

By G. E. Perry, J. F. Bruskotter, D. G. Russell, J. H. Goodrich

The depletion performance of gas wells has been investigated by mathematical simulation techniques. The gas well model which was studied consisted of a single well located in the center of a bounded, cylindrical, homogeneous reservoir. Dependency of gas compressibility and viscosity on pressure was considered in studies of well performance at both constant mass flow rate and constant flowing pressure conditions. To carry out the investigation, the nonlinear, second-order, partial differential equation which describes Darcy flow of a nonideal gas through porous media was solved numerically. Some of the previous investigations of gas well performance have been of limited general use, because assumptions were introduced to simplify either the gas properties or the basic differential equation. Other studies have been rigorous in these respects but have presented a very limited set of calculated results. The present study was attempted to present a rigorous theoretical model and sufficient numerical results to permit meaningful conclusions to be drawn. It was found that all terms must be retained in the partial differential equation to make accurate predictions. The neglect of higher-order terms, e.g., terms of the order of the "gradient squared", leads to serious material balance errors at large times and to conservative estimates of gas well performance. The higher the gas flow rate and/or the lower the permeability-thickness product of the formation, the more pronounced are these deviations. For example, in a well draining 640 acres in a 25-md-ft formation (8,120 MMcf gas in place) at a constant rate of 993 Mcf/D, the rigorous solution predicts a bottom-hole pressure decline from 4,000 to 1,000 psia in 8.7 years. If higher-order terms are neglected in the differential equation, this decline in pressure is predicted to occur in 5.3 years. With the results of the numerical solution of the differential equation as a basis, simple, easy-to-use approximations for predicting gas well performance for Darcy flow conditions have been developed. These simple approximations are based on the familiar equations for flow of a single, slightly compressible fluid. The approximate methods possess a high degree of accuracy and enable the prediction of long-term gas well performance to be made quickly and accurately without the use of a digital computer. Both transient and stable flow period approximations were developed. INTRODUCTION In recent years income from the sale of natural gas and associated products has represented an ever-incre as ing fraction of the industry's total revenue from operations. To meet the surge in demand for natural gas, the industry has depended heavily upon established reserves and has actively pursued development of new reserves. The search has progressively led to reservoirs which yesterday were too tight and/or deep to yield the desired return on invested capital. More than ever before, evaluation accuracy is now required to forecast the criteria upon which engineering recommendations and management decisions are based. Considerable effort has been expended by both research and operations personnel on the development and application of methods for analyzing and predicting the performance of gas wells. Fundamentally, the problem is the familiar one of extracting data during the drilling, testing and early production life of a well and applying these data within an accurate simulation model to predict long-term behavior. During the past 30 or more years a voluminous literature dealing specifically with gas field problems has been generated. A recent book' lists a comprehensive bibliography of published material through 1959. Over 1,200 references are cited. Since then 39 additional articles on natural gas technology have been published in Transactions volumes of the Society of Petroleum Engineers of AIME. Most existing theory for predicting gas well performance requires that one or more idealizations (e.g., steady-state flow, ideal gas of constant viscosity, small and constant compressibility and constant-viscosity fluid) be applied. Although existing theory may apply directly or be adapted by various artifices to describe specific gas well and reservoir behavior, no widely applicable method is available, and existing methods appear to be subject to appreciable error unless better limits of applicability are defined. The objectives of this paper are (1) to present numerical solutions to the partial differential equation describing gas flow under conditions of general interest in gas well performance prediction work, (2) to present solutions which possess a high order of accuracy for both transient and stabilized flow periods of a well producing at constant rate or constant pressure, and (3) to develop and present simplified relationships which can be used as high-order approximations to the exact numerical results for fast and accurate predictions of gas well performance at the operating level. Combined, these objectives are designed gen-

Jan 1, 1967

By P. Douglas, G. M. Leak, B. Mills

The sinusoidal surface relaxation technique has been used to measure the surface self-diffusion coefficient of spectroscopically pure nickel over a wide temperature range under a hydrogen atmosphere. A kink in the Arrhenius plot has been observed. In the temperature range T/T 0.98 to 0.80 (T in O K and T, is the melting temperature) the average self diffusion coefficient is given by Below the temperature T/T,- 0.80a decrease in the slope of the log Ds us 1/T plot is observed. This is associated with a diffusion process characterized by a lower activation energy (-20,000 cal mole'') and smaller preexponential term (-10- sq cm sec"). A series of experiments were carried out at T/Tm = 0.61 under a hydrogen atmosphere of higher oxygen partial pressure than for the rest of the experiments. It was found that Ds was significantly depressed due to oxygen adsorption. This evidence supports the opinion that the low temperature process (activation energy -20,000 cal mole-') is unlikely to be due to oxygen adsorption. An interesting feature of the present data is that the transition temperature (T/Tm - 0.80) is a function of orientation. For a small number of crystals of measured orientation the transition temperature was observed to be higher towards the low index (100) pole. Theories of surface diffusion are briefly reviewed and it is concluded that the present reszuts are best explained by invoking a surface roughening process. GJOSTEIN has recently analyzed available surface diffusion data for a wide range of metals. He suggested that two mechanisms were operative for fcc metals, an adatom process at high temperatures and a vacancy process at low temperatures. Results for nickel can be summarized as follows. At low temperatures (T/T, - 0.3 to 0.44) under ultra high vacuum conditions, Melmed2 measured an activation energy Q of 21 kcal mole-' using field electron emission microscopy. At higher temperatures (T/T - 0.7 to 0.9) under a vacuum of 10- ' torr, Maiya and lakel measured y as 39 kcal mole-' using the multiple scratch smoothing technique. The present work was undertaken to try to find out if two distinct processes could be observed. High temperature results give Q about 47 kcal mole-': there is evidence also for a low temperature value of about 20 kcal mole-'. These measurements were all made under a hydrogen atmosphere, in the temperature range 860" to 1412°C. Concurrent with the present study Bonze1 and jostein> have also observed a break in the Arrhenius plot for the (110) surface of nickel. These measure- ments under ultrahigh vacuum conditions using the laser diffraction technique are in excellent agreement with the work reported here under hydrogen annealing conditions. THEORY The available surface relaxation techniques include single and multiple scratch smoothing and grain boundary grooving. The processes have been compared in detail by Gjostein for conditions where surface diffusion dominates6 and Mills et al? where volume diffusion dominates. In summary the relevant points are as follows. Grain boundary grooving gives an average Ds for the two surfaces adjacent to the boundary and this can, to some extent, be simplified by using symmetrical bicrystals. This technique has been used to study the effect of environment on Ds for silver and copper.'-'' Scratch techniques yield Ds values for the small orientation range exposed by the scratches (-2 deg). The multiple scratch process is preferable because the profile rapidly becomes sinusoidal and can then be interpreted theoretically in a relatively simple way. Also corrections for mass transport processes other than surface diffusion can be introduced easily. Mullins" considered a sinusoidal profile described the wavelength of the profile. After time t the profile can be described by the equation The terms A, A', C, and B which account, respectively, for contributions due to evaporation-condensation, diffusion through the gas phase, volume diffusion through the lattice, and surface diffusion are defined as: where Ds = the surface self diffusion coefficient ys = the surface energy per unit area p = the equilibrium vapor pressure over a flat surface pa = the equilibrium vapor density over a flat surface DG= the diffusion coefficient of vapor molecules in the inert gas DM = the mass transfer diffusion coefficient which for a pure cubic metal is Dv/f where Dv is the radiotracer diffusion coefficient and f is the correlation factor H = the molecular volume V = the surface density of atoms, il2'3 M = mass of an evaporating molecule

Jan 1, 1970

By Lee Hillard Meltzer, Ralph E. Davis

INTRODUCTION During the past few years emphasis has been placed upon methods of estimating the future expectancy of gas production from natural gas fields. Before technical methods were applied, the production expectancy over future years was based upon the knowledge of gas well behavior, learned through long experience and embedded in the "know-how" of men long in the gas producing business. It is doubtful that a technical study of future expectancy of a gas field or a group of fields was ever prepared for the preliminary planning of a natural gas pipe line system built prior to about five years ago. The decline in well production capacity was naturally recognized by all familiar with the business since its earliest beginnings more than 75 years ago. In 1953, the Bureau of Mines published Monograph Number 7, "Back-Pressure Data on Natural Gas Wells and Their Application to Production Practices," which gave to the industry the first technical analysis of the decline in production of individual gas wells. This method affords a means of estimating the future production in relation to decline in reservoir pressure. The demand for technical determination of expectancy of future gas productivity from fields or a group of fields led technical men to the application of the knowledge of well behavior to the problems. The decline in a well's ability to produce as pressures declined could be estimated by the use of the curve known as the "back-pressure potential curve" as developed by the Bureau of Mines. A field containing few, or even numerous, wells could be analyzed on the basis of the sum of potentials of all wells. In most studies of this nature, the problem is to estimate the rate of production that can be expected, not only from present wells but also, from wells that will in the future have to be drilled into the reservoir being studied. The "back-pressure potential" method requires that the following data be known or estimated: (1) Proved gas reserves. (2) Current shut-in pressures and rate at which shut-in pressures change with production. (3) Back pressure potential data on wells in the source of supply. (4) Ultimate number of wells which will supply gas, and their potential. (5) Limitations on productivity such as line pressures against which the wells will produce, friction drop in the producing string, and so forth. It is evident that the resulting estimate of gas available in each year for a future of say, 20 years, contains many uncertainties. While the method may have considerable merit for a field that is fully developed, it cannot be completely dependable in fields that are only partially developed. In such cases, some of the data upon which it is based can only be estimated or assumed. In the study of this problem during the past few years, a method has been developed which we believe has great merit, especially when applied to fields subject to substantial future drilling, and when applied to the study of fields which, on the average, appear to have characteristics similar, in general, to the average of the fields used in the development of the "yardstick" outlined herein. From an analysis of the production history of 49 reservoirs which are depleted, or nearly depleted, a curve has been constructed which shows the average performance of the reservoirs during the declining stages of production. When properly applied, this "average performance curve" can be used to determine the stage of depletion at which a reservoir or group of reservoirs will no longer be able to yield a given percentage of the original reserves. "AVAILABILITY" AND "AVAILABILITY STUDIES" The rate at which. a reservoir will yield its gas depends basically upon physical factors, such as the thickness and permeability of the sand, the effect of water drive, if any, and other conditions, and upon economic factors, such as the number of wells drilled. Within the ranges set by the physical conditions, a rate of delivery tends finally to become established. The rate (or range of rates) represents a balance between the interests of the operator, who desires the maximum return from his property and of the pipe line owner, who desires to maintain a firm supply for his market. This balance, which is influenced by the terms of the contract, determines the capacity which will be developed by the operator, and the time and rate at which the decline in production is permitted to occur. Thus the "availability" of gas

Jan 1, 1953

By P. Greenfield, C. C. Smith, A. M. Taylor

The Mg-Zr alloy ZA and Mg-Mn alloy AM503(S) are shown to have a markedly improved resistance to creep deformation after suitable heat treatments. This improvement makes them suitable for certain stress-bearing fuel element components in nuclear reactors. The extent of strengthening is described and an explanation of the behavior of both materials is given, based on a combination of strain-aging and grain growth. The increase in operating temperatures of fuel element components in Calder Hall type nuclear reactors has necessitated the development of magnesium base alloys with a very high resistance to creep at temperatures up to 500°C. Such alloys are not required for fuel element cans, which require high-creep ductility rather than strength, but for can supporting and stabilizing components, which are needed to support the imposed loads without deforming more than about 1 pct in times of up to 40,000 hr. The amount and type of alloying addition made to magnesium for these parts is limited by the necessity of keeping the cross-section to thermal neutrons as low as possible. The alloys must also possess a high resistance to oxidation in CO2. Alloys which have been developed for this application include ZA, an alloy of magnesium with 0.5 to 0.7 pct Zr and AM503(S), an alloy of magnesium with 0.5 to 0.75 pct Mn. In the as-extruded condition these alloys are very weak and ductile in creep but it has been found that they can be strengthened to a significant extent by heat treatment. This paper describes the method of developing a high-creep resistance in ZA and AM503(S), the extent of the strengthening produced and discusses the probable mechanisms of strengthening. TEST MATERIALS Specimens were taken from typical casts of ZA and AM503(S) alloys extruded into 2 1/4-in.-diam bars, supplied by Magnesium Elektron Ltd. Typical analyses of the bars were as follows: The as-extruded mean grain diameter was 0.001 to 0.002 in. for the ZA alloy and 0.003 in. for the AM503(S) alloy. EXPERIMENTAL METHODS Extruded bars of ZA alloy, 2 1/4 in. in diameter and 9 in. long, were heat treated in electrical resistance furnaces in an atmosphere of flowing CO2 containing 50 to 300 ppm water, thereby reducing the extent of oxidation compared with that which would have occurred in air. Heat treatments were carried out at 600oc for times of 8, 24, 48, 72, and 96 hr and material was subsequently both furnace cooled and water quenched. In order to measure the effect of time of heat treatment, specimens were creep tested at 400°C and 336 psi for about 1000 hr. Subsequently, the behavior of material heat treated for 96 hr at 600°C and furnace cooled was tested at a variety of stresses from 200° to 500°C. Tests were also conducted at 200o and 400°C on material in the as-extruded condition for comparative purposes. With the AM503(S) alloy, only the effect of heat treatment at 565°C for 4 hr was examined. It has been shown1 that such a heat treatment produces marked strengthening in this alloy. Tests on this material were conducted at a variety of stresses at 200°, 300°, and 400oc with comparative tests on as-extruded material at 200o and 400°C. The creep tests were carried out on machines using dead-weight loading and direct micrometer strain measurements on specimens 5 in. long and 0.357 in. diameter. At temperatures of 400° C and below, the creep tests were conducted in air, but at higher temperatures an atmosphere of CO2 was used. Grain size measurements were made on ZA in the extruded and heat treated states and on each specimen after creep testing. This was done by a line count of a minimum of 20 grains in two or three random fields in the longitudinal and transverse directions. The same method was used for measuring the grain size of as-extruded AM503(S), but the grain size of the heat treated material was so large that this method could not be employed. For heat-treated AM503(S) the large grained characteristics (between 0.1 and 1 in.) were confirmed by the measurement of individual grains. In the case of the ZA alloy, specimens taken from various stages in the program were analysed for hydrogen by a combustion method. Material in various states was also analysed for the soluble and insoluble zirconium content by dissolving in dilute hydrochloric acid. This technique has been useda for the determination of amounts of zirconium present

Jan 1, 1962

By E. T. Turkdogan, P. Grieveson

Experimental results are presented for the rate of solution of nitrogen in a iron in the temperature range 750° to 873°C and in 6 iron in the temperature range 1410° to 1470°C. It is shown that the rate controlling process is diffusion of nitrogen into the iron. The diffusiting of nitrogen in a and 6 iron is derived from the results, and the temperature dependence of the diffusivity is represented by the equation D = 7.8 x e- 18,900/RT sq cm per sec. The solubility of nitrogen in a and 6 iron, in equilibrium with 1 atm pressure of nitrogen, has been measured. Using these results and other available data, it is found that the variation of the logarithm of nitrogen solubility with the reciprocal of absolute temperature is nonlinear. In an Appendix, some results of Darken and Smith are presented for the rate of solution of nitrogen in iron using ammonia + hyidrogen mixtures. These data also support the view that diffudsion of nitrogen in iron is the rate-controlling process when ammonia + hydrogen mixtures are used. A considerable effort has been made to obtain data on the solubility1-5 and diffusivity of nitrogen in a iron6-l2 because an understanding of the effect of nitrogen on the properties of steel must be based on an accurate knowledge of the properties of nitrogen in pure iron. However, no information is available concerning the kinetics of solution of nitrogen in a and 6 iron. Recently the authors13 have investigated the rate-controlling mechanism operating in the kinetics of solution of nitrogen in y iron. This study was directed to determine the rate-controlling processes for similar reactions with a and 6 iron as well as to establish values for the solubility of nitrogen in equilibrium with nitrogen gas in a and a iron. EXPERIMENTAL The procedure used in experiments to determine the rate of solution in cylindrical iron rods was the same as that described in a previous communication.13 Ferrovac E grade iron used in all experiments contained the following impurities in weight percent: C, 0.005; Mn, 0.001; P, 0.002; S, 0.006; Si, 0.006; Ni, 0.025; Cr, 0.002; V, 0.004; W, 0.02; Mo, 0.01; Cu, 0.001; Co, 0.01; 0, 0.007. After cleaning the surface, the iron rods were treated in an atmosphere of purified hydrogen for 17 hr before the reacting gas was introduced for known experimental times. After quenching, the samples were sectioned radially and analyzed for nitrogen. In addition to experiments using rods, iron foils were used in the measurements of solution rates of nitrogen in a iron. The foils of two different thicknesses were prepared by cold rolling Ferrovac E grade iron cylindrical rod to 0.051 and 0.152 cm. Foil samples were used in a rectangular form 5 cm long and 1.25 cm wide. The specimens were thoroughly cleaned of surface oxide with fine emery cloth and degreased with carbon tetrachloride immediately before entry into the furnace. The experimental procedure was the same as that used in the study with rods. At the completion of an experiment, the foil samples of the nitrogenized iron were analyzed for nitrogen after discarding 0.3 cm from the perimeter of the specimen. Iron foils were nitrogenized and denitrogenized in the a and 6 range with a gas mixture of 95 pct N and 5 pct H for times varying from 5 min to 2 hr. Results obtained for the average composition of nitrogen in iron for these experiments are presented in Fig. 1. Prior to the denitrogenization experiments, the samples were saturated with nitrogen at 1000°C and 0.67 atm N, giving a uniform nitrogen concentration of 0.0204 pct. According to the known a-y phase boundary in the Fe-N system,14 this composition lies within the ferrite region at temperatures 750" to 850°C. Use of this initial nitrogen content insured that reaction occurred between the gas and a single solid phase, a iron. Examples of the results for the mean concentrations of nitrogen in cylindrical iron rods, 0.356 cm radius for both the a and 6 ranges are given in Fig. 2. Typical examples of the results obtained for the radial distributions of nitrogen in rods are presented in Fig. 3. It appears that the results for radial distributions can be extrapolated to constant surface compositions which agree with the equi-

Jan 1, 1964

By L. A. Wilson, P. J. Root

The relative costs of heating a reservoir by steam injection and by combustion have been examined. The comparison was based on a model similar to that proposed by Chu.' The cost of boiler feed water, the price of fuel, pressure and plant capacity were parameters in determin-ing the costs of air compression and steam generation. The analyses compare the cost of heating to the same radius by the two methods. Results suggest that the two primary factors for comparison are the price of fuel and the amount of crude burned during underground combustion. The cost of fuel has a greater effect on the cost of heat from steam than it does on its cost by combustion. As a result, analyses indicate that when the price of fuel is low, steam may be unequivocally cheaper than air. The influence of heat loss is such, however, that as the heated radius increases combustion becomes relatively more competitive depending upon the amount of crude burned. This implies that steam may be cheaper for small stimulation jobs (huff and puff) but combustion may be more economically attractive for heating large areas (flooding). INTRODUCTION Use of thermal methods of recovery is an accepted fact today. After an induction period of several years, processes are being widely used that involve reservoir heating to augment recovery. Of the several techniques, steam injection and forward combustion appear to be destined to dominate the field. Although the objectives of both are the same, the basic differences between generating heat in situ and injecting heat after surface generation influence the cost in different ways. This study compares the cost of heating a reservoir either by steam injection or by forward combustion. There has been no consideration of recovery. Presumably, recovery from the swept region would be high in either case. The sole consideration was the cost of heating to the same radial distance by either process. PROCEDURE THE MODEL The basis for comparison was a mathematical model similar to that used by Chu' for combustion. The model simulates a radial heat wave in two-dimensional cylindricaI coordinates. It includes heat generation, conduction and convection within the reservoir and conduction in the bounding formations. Thus, heat losses from the formation are considered. Three significant modifications were made. 1. Equal logarithmic increments rather than equal increments were used for the mesh spacing in the r direction. By this technique large distances were simulated with relatively few mesh spaces. 2. A backward difference approximation to the convection term was used to avoid troublesome oscillations which result from a central difference approximation when the convection term is large. 3. The radial increments of the combustion zone motion were not necessarily uniquely related to the mesh configuration. The cumbersome step function introduced by the heat of vaporization of steam was circumvented by assuming the enthalpy of the steam to be a linear function of temperature between reservoir temperature and steam temperature. This is equivalent to assuming an average heat capacity numerically equal to the difference between the enthalpy of saturated steam and the enthalpy of water at reservoir temperature divided by the difference between the two temperatures. Heat losses obtained by this model are in essential agreement with those obtained by the analytical solution of Rubenshtein.' A detailed description of the model is presented in the Appendix. Using the model, the times required to heat to particular radial distances were obtained as a function of injection rate and other physical parameters. For the steam case, injected fluid was assumed to be saturated steam at pressures of either 500, 1,000 or 1,500 psia. The corresponding temperatures are 467, 544 and 596F, respectively. Thickness ranged from 10 to 50 ft and injection rate ranged from 100,000 to 1 million Ib/D. Reservoir and overburden temperatures at the injection well were assumed to be that of saturated steam at the injection pressure. The effect of maintaining the overburden temperature at the well at a different temperature (initial reservoir temperature) was examined with no significant change in behavior. The influence of wellbore heat losses for the steam case was determined in the following manner. The rates of heat loss as a function of time were estimated using an approach similar to that suggested by Ramey." he data were based on injection through 2%-in. tubing in 7-in. casing. Integration of these data over the entire iniection period yielded the total heat loss. Total heat losses were then corrected to their equivalents in steam (this number resulted from dividing the total heat loss by the latent heat). This was considered additional steam required to accomplish the reservoir heating and the total cost was increased accordingly.

Jan 1, 1967

By F. M. d’Heurle

Films of molybdenum have been prepared by sputtering onto oxidized silicon substrates. The resistivity. lattice parameter, orientation, and grain size were studied as a function of substrate temperature and substrate bias. Under normal sputtering conditions, the resistivity of the films was found to be quite high (600 x 10 ohm-crn). However, with the use of the negative substrate bias of 100 v and a substrate temperature of 350°C, films weve produced with a resistivity of ahout twice that of bulk molybdenum. The lattice parameters measured in a direction nornzal to the surface of the films weve found to be gveatev than the bulk value. This was interpreted as being at least partly due to the presence of compressive stresses. The effects of annealing in an Ar-H atmosphere were studied in terms of diffraction line width, lattice parameter, and resistivity. BECAUSE of its relatively low bulk resistivity (5.6 x 106 ohm-cm)' molybdenum is potentially interesting as a thin-film conductor in integrated circuits. An additional feature which makes it attractive for this purpose is its low coefficient of expansion (5.6 x KT6 per "c),' which is fairly well matched to that of silicon (3.2 x 10 per c). It is possible to deposit molybdenum films by evaporation but generally films produced in this manner have a high resistivity. In order to achieve resistivities close to bulk value, Holmwood and Glang found it necessary to operate in a vacuum of about 107 Torr and to maintain the substrates at 600 C during film deposition. Sputtered molybdenum films have been examined by Belser et a1.7 and, recently, by Glang et al.' This paper describes the results of an attempt to extend some of that work and examine the effects of annealing and getter sputtering on the physical and structural properties of the films produced. SPUTTERING APPARATUS AND PROCEDURE The apparatus used for most of the film sputtering work described here consisted of two "fingers" serving as anode and cathode, respectively, which were mounted within an 18-in.-diam glass chamber. A liquid nitrogen-trapped 6-in. diffusion-pump system was used to achieve a vacuum of about 1 x 107 Torr within the chamber prior to sputtering. The essential features of the equipment are shown in Fig. 1. Cathode and anode fingers are stainless-steel tubes isolated from the top and bottom plates by Teflon collars. In order to limit the discharge to the space between anode and cathode, each finger is surrounded by an aluminum hield, at ground potential, having an internal diameter 18 in. larger than the outside diameter of the finger. The cathode and anode fingers are 6 and 4 in. in diam, respectively. A 116-in.-thick sheet of molybdenum is brazed with a 10 pct Pd, 58 pct Ag, 32 pct Cu alloy to a copper disc which is mounted by means of screws and a large 0 ring onto the lower end of the cathode finger. The disc is cooled during sputtering by water circulation inside the finger. The use of several feet of plastic tubing for the water input and outputg reduces leakage to ground to less than 1 ma when the cathode potential is raised to 5 kv. The upper end of the anode finger is terminated by a brazed-on copper block. A variety of specimen holders can be easily mounted on the upper face of this block. Substrate heating or cooling is achieved by use of an appropriate unit attached to the lower face of the same block. Heating is achieved by means of cartridge-type heaters and cooling by copper coils fed with forming gas under pressure. The inner chamber of the specimen finger constitutes a small vacuum chamber of its own which is evacuated by an auxiliary mechanical pump in order to limit heating element oxidation and heat transfer by convection currents. An advantage of the finger arrangement is the absence of cooling and heating coils and wires within the main chamber. The stain less-steel shutter is useful to establish a discharge for cleaning the cathode at the beginning of each sputtering run. Water cooling of the shutter reduces heating and the out-gassing of impurities which might condense on the nearby substrates. Unless otherwise specified, the substrates used in these experiments were 1-in.-diam oxidized silicon wafe:s, 0.007 in. thick, having an oxide thickness of 6000A. The substrate holders were large copper discs onto the surface of which a number of molybdenum discs, 116 in. thick and 78 in. in diam, were brazed. The wafers were clamped to the molybdenum discs

Jan 1, 1967

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to illustrate the application of the theory of extremes to this fore-casting problem. For example, it is customary for design purposes to determine the rupture strength of geologic materials. The theory of extremes is exceedingly useful in describing that portion of the frequency distribution of rupture strength which contains the least strengths. Parameters describing the distribution of the least strengths are more important to the designer of mining excavations than parameters describing the total distribution. The basic principles of the theory of extremes will be detailed and illustrated. Any person required to work in the laboratory of nature is aware that uncertainty is a salient feature of all mining enterprises. A mining engineer required to plan the most efficient, practicable, profitable, and safe mine finds himself face to face with numerous ill-understood and often unquantifiable states of nature. Basic information necessary for adequate planning is often lacking or derived from incomplete tests on samples or experience of doubtful validity. The planning procedure usually takes the form of determining a feasible layout with the intent of determining an optimal layout when and if the necessary details and information become available. The crux of the entire procedure is the choosing of numbers to put into the operational and structural models which encompass the plan. Many times these numbers must be assigned qualitatively from past experiences and are called the "most probable ones." At other times, load records, performance records and material tests provide a basis for extrapolation. In any event, the numbers are chosen from a distribution or set of all numbers. Since each number in the distribution represents a possible state, the choice of any particular value is based upon a decision rule. To illustrate, consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model various intensities of behavior are possible depending upon the load, deformation, and material characteristic spec-trums, respectively. Of particular interest to mining people is the failure behavior or condition, i.e., when there is a complete collapse of structural resistance by either structural instability or fracture. A necessary feature of the analysis is the "rupture strength" of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. The methodology used to overcome this variation is to construct a frequency distribution of rupture strengths, and then determine a measure of central tendency and variability. The main idea involved is that the central tendency number will be used in the failure calculations and the measure of dispersion will be used to estimate the probability of failure. In particular if the distribution of rupture strength is normal, the mean rupture strength is the central tendency number and the standard deviation of the rupture strength is the measure of variability. Suppose the mean value of rupture strength is 1000 psi and the standard deviation is 200 psi. Insertion of 1000 psi into the failure calculation produces results that are unsafe, hence a common decision rule is to reduce the mean value by a "factor of ignorance" so that the failure calculation will produce a "safe result." If two is chosen as a factor of ignorance, this means the value inserted in the calculation is 500 psi or 2.5 times the standard deviation. The next step is to determine the percentage chance that failure will occur from a design created on this basis. Tables on the normal distribution function show that this percentage chance is 0.621% or approximately 7 times out of 1000. In practice, however, the situation is more complicated than represented by the foregoing illustration. The laboratory or field testing program usually constitutes a pathetically small sample of the geologic universe of interest and not enough testing is carried out to determine the exact form of the distribution of the test results. The normal, Cauchy and Student's T distributions are strikingly similar, and it becomes a matter of mathematical convenience to assume the normal law for phenomena which follow other laws.

Jan 1, 1969

By D. L. Feucht, R. L. Longini

The semiconductor heterojunction is considered in terms of simple models which may lead to an understanding of move complex heterojunctions. Metallurgical and electrical properties of hetero-junctions aye discussed including the interface structure, energy -band diagram, and carrier transbovt across the interface. It is found that in a heterojunction all mechanisms such as injection, tunneling, and junction recombination found in simple junctions play modified voles. INTERFACES between materials (grain boundaries, the electrical junction between two differently doped materials in a single crystal, the oxide-metal interface, or metal-metal junctions) are of considerable importance in many situations. These various interfaces all have one very fundamental thing in common. Quantum mechanically speaking, the wave functions of the electrons in one material may penetrate the other material but, in general, only to the extent of angstroms. From an electrical point of view the conduction mechanism changes as a current passes through such junctions. In some cases the change is tremendous, in others almost negligible. The interface, then, is the locus of a change of conduction mechanisms. Some of these, particularly in semiconductors, are well-understood. The ordinary p-n junction in a single crystal can be the locus of an injection mechanism or a tunneling process, depending on conditions. The mechanisms are probably best understood in semiconductors because of the possible simplified view of particlelike conduction. The bands are either nearly filled or nearly empty and band overlap is seldom involved. The same fundamentals are probably important in other situations too but they are very difficult to look at naively. Although the simple look at the semiconductor case only gives us a relatively rough picture which must then be refined, the other systems, which involve a more complex situation, immediately are in many ways too difficult. There are too many initial choices of complex systems and therefore it is not possible to be even reasonably certain of any one model. Because of the relative simplicity of semiconductors, their good and controllable structure, and because of the ability to make many measurements on them not normally available to either metals or insulators! they are probably the best understood materials. It is therefore desirable to use them as a tool to further the understanding of interfaces in general. Semiconductor-heterojunction concepts were first proposed by kroemer1 in 1957. This was followed several years later by reports on the fabrication and experimental characteristics of heterojunction structures by Anderson2 and Diedrich and jotten.3 I) THE HETEROJUNCTION STRUCTURE To get down to hardware, when we refer to a semiconductor heterojunction we imply that there exists an intimate contact between different semiconductor materials. We could put two pieces of material together, complete with oxide layers, we could remove the oxides, or we could even melt the interface and hopefully get wetting and a good "bond" on solidifying. In fact we could by some means grow a crystal of one material using the other as a seed. Essentially we are interested only in the last two because they are the simplest to look at analytically. The degree of perfection of fit varies greatly and is reflected somewhat in the arc welder's joint strength. The lattice match of the two materials, their orientation, and so forth. is obviously necessary for a good bond but so is the continuity of any polar bonds which are involved such as in the III-V semiconductors. The mechanical misfit between two similar lattices can be described in terms of edge dislocations. The edge-type dislocations must be very close together for the usual misfit and there must be dislocations for each of several different Burger's vectors in order to produce a lattice match. The .'dangling bonds'' resulting will be involved in producing interface charge. Order of magnitude estimates of the charge density extrapolated from low densities of dislocations in homogeneous materials give 5 x 1013 cm-2 Ge-Si and 1 X 1012 cm-2 Ge-GaAs electronic charges. Edge dislocations also act as very active recombination centers between holes and electrons. One lattice "matching" difficulty usually exists even if two structures have essentially the same lattice constants as they will have different coefficients of therma1 expansion. Thus, on cooling from the usually high temperature of fabrication to room temperature, dislocations are produced, a good fit not existing at both temperatures. In brittle materials this shrinkage may even result in cracking. For the Ge-Si interface the mismatch is about 2 x 10 -6 per degree whereas it is less than 10"7 per degree between germanium and GaAs. The exact effect of the misfit is dependent on the thickness of the materials involved. For a very

Jan 1, 1965

By Nicholas J. Grant, John S. Benjamin

A series of composite alloys containing a high volume of NiAl, Ni3Ah or CoAl, bonded with 0 to 40 vol pct of a ductile metal phase, were prepared by powder blending and hot extrusion. The binder metals were of four types: pure nickel or cobalt, near saturated solid solutions of aluminum in nickel and cobalt, type 316 stainless steel, and niobium. Sound extrusions were obtained in almost all instances. Studied or measured were the following: interaction between the alunzinides and the binders, room-temperature modulus of rupture values, 1500° and 1800°F stress rupture properties, hardness, structure, and oxidation resistance. Stable structures can be produced for 1800°F exposure, with interesting high-temperature strength and good high-temperature ductility. Oxidation resistance was excellent. A large number of experimental investigations have been made of the role of structure on the properties of cermets and composite materials. Gurland,1 Kreimer et al.,2 and Gurland and Bardzil3 have indicated the preferred particle size in carbide base cermets to be about 1 µ, with a hard phase content of 60 to 80 vol pct. The optimum ductile binder thickness was noted to be 0.3 to 0.6 µ.1 Complete separation of the hard phase particles by the binder is important in reducing the severity of brittle fracture.' The purpose of the present study was to produce structures comparable to the conventional cermets, using a series of relatively close-packed intermetal-lic compounds rather than carbides as the refractory hard phase, and to study the effects of binder content and composition on both high- and low-temperature properties. The selected intermetallic compounds were particularly of interest because of the potential they offered in yielding room-temperature ductility. The highly symmetrical structures are known to possess high-temperature ductility and room-temperature toughness. Based on a ductile binder, the alloys were prepared by the powder-metallurgy route to avoid melting and subsequent alloying of the matrix, and were extruded at relatively low temperatures. It was expected that the composite alloy would retain useful ductility. In contrast, infiltration and high-temperature sintering led to alloying of the matrix and to decreased ductility. The systems Ni-A1 and Co-A1 were selected for this study. In the Ni-A1 system the compounds NiA1, having an ordered bcc B2 structure, and Ni3Al(?1), having an ordered fcc L12 structure, were chosen. In the system Co-A1 the intermetallic compound CoAl with an ordered bcc B2 structure was used. ALLOY PREPARATION The intermetallic compounds, see Table I, were prepared by using master alloys of Ni-A1 and CO-A1, with additions of either cobalt or nickel to achieve the desired compositions. The master alloy in crushed, homogenized form, was melted with pure nickel or cobalt in an inert atmosphere, cold copper crucible, nonconsumable tungsten arc furnace. The resultant intermetallic compounds were homogenized at 2192°C in argon, crushed, and dry ball-milled in a stainless mill to -100 and -325 mesh for the Ni-A1 compounds and to -325 mesh for the CoAl compound. Finer fractions were separated for some of the composite alloys. Several ductile binders were utilized. These included Inco B nickel, 5µ ; pure cobalt, 5 µ, from Sher-ritt Gordon Mines, Ltd.; fine (-325 mesh) niobium hydride powder; fine (15 µ) type 316 stainless-steel powder; and near-saturated Ni-A1 and Co-A1 solid-solution alloys, also in fine powder form. The niobium hydride was decomposed above about 700°C in processing of the compacts in vacuum to produce niobium powder. The Ni-7.1 pct A1 and the Co-5.3 pct A1 solid-solution alloys were prepared from pure nickel or cobalt and pure aluminum by nonconsumable tungsten arc melting under an inert atmosphere. The ingots were homogenized, lathe-turned to fine chips, and dry ball-milled in air to -325 mesh powder. These solid-solution alloys are designated NiSS and CoSS; see Table I. Subsequently the hard and ductile phases were dry ball-milled as a blend. Experiments clearly established the need to coat the hard particles with the ductile binder to optimize subsequent hot compaction by extrusion. Ordinary dry mixing usually resulted in nonhomogeneous alloys which were quite brittle. Conventional cermets are consolidated by liquid phase sinteiing or infiltration, which resulis in undesirable and uncontrolled alloying of the binder phase. For this study, a loose (unsintered) powder-extrusion process was emploved, minimizing reactions between binder and hard particle, thereby permitting much greater control of composition and structure. The constituent powders were first mixed in the desired

Jan 1, 1967

By L. Seigle, R. Resnick

An inert-marker movement experiment indicates that the ratio of the intrinsic diffusion coefficients DC:DTa = 80:l in TaC at 2500°C. Measurements of the diffmion coefficient of carbon in nonstoichiometric TaC at temperatures from 1700° to 2700°C reveal that Dc increases with decreasing carbon content, but much less than expected from the probable change in vacancy concentration with carbon content. A diffusion process involving two simultaneously operating mechanisms is postulated, and shown to be theoretically feasible. The average value of the carbon diffusion coefficient is given by DC = 0.18 exp[(-85,000 ± 3000)/RT] sq cm per sec over the composition range 46 to 49.5 at. pct C. BECAUSE of their high melting points and hardness, the carbides of the IV, V, and VI group transition metals, along with those of uranium, have attracted considerable interest for applications at high temperatures. In these applications the reactivity of the materials is important, and, since rates of diffusion within the compounds influence reactivity, a knowledge of diffusion kinetics and mechanisms is desirable. While many investigations of the mechanical and electrical properties of these compounds have been made, only two fundamental investigations of diffusion in the carbides are known. Chubb, Getz, and Townleyl measured the diffusivity of carbon and uranium in UC, and Gel'd and Liubimov2 measured the diffusivity of carbon and niobium in NbC. This paper describes an investigation of the diffusion of carbon in tantalum monocarbide and, in particular, the influence of carbon deficiency on this process. Tantalum carbide melts at approximately 3800°C, which makes it one of the highest melting materials known. The compound exists over a rather wide range of carbon Content.3-7 At the peritectic temperature, 3240°C, the phase extends from about 36 to 50 at. pct C. Although the compound can exist with a substantial carbon deficiency, the high carbon phase boundary remains near the stoichiometric composition over the entire temperature range; i.e., no carbon excess is observed. The structure of TaC is the NaCl type wherein carbon atoms normally occupy the octahedral sites in a somewhat expanded fcc lattice of tantalum. Decrease of the lattice parameter with decreasing carbon suggests that the removal of carbon introduces octahedral vacancies into the lattice. I) EXPERIMENTAL DETAILS AND RESULTS Inert-Marker Experiments. In a compound such as TaC the interstitial element would be expected to diffuse more rapidly than the metal. This was confirmed by an inert-marker experiment, following Srnigelskas and irkeendall.8 Ideally, the markers should be placed at the interface between a slab of low-carbon TaC and graphite, and their movement during subsequent inter-diffusion measured. Unfortunately, no solid could be found which is unreactive in contact with carbon at the high temperatures employed in these experiments. In order to circumvent this problem, a specimen was designed in which the markers consisted of several small canals running just below the surface of a tantalum slab. This specimen was prepared by machining grooves on the surface of the tantalum slab and then diffusion-bonding a thin plate of tantalum to the slab over the grooves. The surface of the plate was then ground down until the distance between the canals and surface was as small as possible (about 0.01 cm). Thus, the canals would lie entirely within the TaC phase after a short period of diffusion. The diffusion anneal consisted of immersing the metal sample in high-purity graphite powder and heating for approximately 10 hr at 2500°C under vacuum. At this temperature, the vapor pressure is sufficiently high and the transfer of carbon from graphite sufficiently rapid to allow the surface of the diffusion sample to attain the stoichiometric carbon concentration very quickly. Conclusions regarding the relative diffusion rates of carbon and tantalum in the compound layers (TaC and Ta2C) can be drawn from the location of the canals after the diffusion anneals. If the growth of the layers is governed mainly by the diffusion of carbon, as expected, the canals should remain close to the sample surface. If the diffusion of tantalum contributes appreciably to formation of the compound layers, the distance from the markers (canals) to the surface should increase. Fig. 1 shows, diagrammatically, the appearance of the specimens after diffusion, and Table I presents the depth below the surface at which the

Jan 1, 1967

By M. Schwartz, S. K. Nash, R. Zeman

Knoop hardness in the rolling plane and in the longitudinal plane of hot-rolled and cold-rolled sheets of sublimed magnesiu?w was measured as a function of the angle between the long axis of the indenter and the rolling direction. These measurements were correlated with similar data taken on the (0001) and (1010) planes of a single crystal of magnesium where the hardness was measured as a function of the angle between the long axis of the indenter and the [1120] direction. The results were analyzed for compliance with the hypothesis of Daniels and Dunm to account for slip, and with a similar hypothesis to account for twinning. Some hardness anisotropy data are also presented for magnesium-indium and magnesium-lithium solid solution alloys. It is well known that the hardness of a crystalline specimen is different for its different surfaces, and also that the hardness is a function of direction within a single surface. Variations in hardness for single crystals have been found to be much larger than those for polycrystalline materials. Also, materials having low crystal symmetry were found to have a greater anisotropy of hardness than those of high symmetry. 0'Neill1 and Pfeil,2 using a 1-mm Brine11 ball, studied single crystals of aluminum and iron, respectively; and they found a variation of hardness of about 10 pct between readings taken along the principal crystallographic faces. Daniels and Dunn3 found that the Knoop hardness number varied about 25 pct as the long axis of the indenter rotated on the basal plane of a zinc single crystal. The variation on the (1450) plane was about 100 pct, and the average hardness on this plane was about twice that of the basal plane. They also studied the variation of hardness within the (loo), (110), and (111) faces of a single crystal of silicon ferrite and found variations of about 25 pct although the average values for these planes were almost identical. Single crystals of zinc were also studied by Meincke.4 He found that the Vickers hardness numbers varied about 30 pct depending on whether the axis of the indenter was parallel or perpendicular to the (1010) and (1110) planes. Mott and Ford,5 using a Knoop indenter, found a 25 pct variation in hardness on the basal plane of zinc. Crow and Hinsley6 studied heavily cold-rolled bronze, steel, brass, copper, and other metals. They found that the difference in hardness numbers based on the difference in the length of the diagonals of the Vickers indenter was from 5 to 12 pct. Some minerals and synthetic stones show a very large anisotropy of hardness. Robertson and Van Meter7 found the Vickers hardness of arsenopyrite to vary from 633 to 1148 kg per mm2. stern8 using the double-cone method on synthetic corundum found the hardness number to vary from 950 to 2070. And winchell9 reported a variation of hardness number from 184 to 1205 in kyanite. The variation of hardness as a function of direction in a given crystallographic plane in single crystals possesses a periodicity which is related to the symmetry of the lattice. Daniels and Dunn3 found a six-fold periodicity of hardness in the (0001) plane of zinc. They found that the hardness curves of silicon ferrite had a four-fold symmetry in the (100) plane, a two-fold symmetry in the (110) plane, and a six-fold symmetry in the (111) plane. Mott and Ford5 also reported a six-fold symmetry of hardness in the basal plane of zinc. And vacher10 found two-, four-, and six-fold periodicities of hardness in copper on the (110), (100), and (111) planes, respectively. The purpose of this paper is to report the results of an investigation on the anisotropy of hardness as a function of orientation in single crystals of mannes-ium, and samples of rolled magnesium, magnesium-indium, and magnesium-lithium solid solution alloys. The anisotropy of hardness of pure magnesium which had been hot rolled, and then cold rolled various amounts to fracture, was studied by means of Knoop indentation hardness numbers; and the results were correlated with the preferred orientation as determined by quantitative X-ray pole-figure data. A comparison was made of the hardness data obtained from the rolled sheets and those of single crystals of magnesium. In order to obtain a more fundamental understanding of the variation of hardness and of Knoop hardness testing, the data were analyzed by

Jan 1, 1962

By H. R. Thresh

An oscillational vis cometer has been constructed to measure the viscosity of liquid metals and alloys to 800°C. An enclosed cylindrical interface surrounds the molten sample avoiding the free surface condition found in many previous measurements. Standardization of the apparatus with mercury has verified the use of Roscoe's formula in the calculation of the viscosity. Operation of the apparatus at higher temperatures was also checked using molten lead. Extensive measurements on five different samples of zinc, of not less than 99.99 pct purity, indicate i) impurities at this level do not influence the viscosity and ii) the apparatus is capable of giving reproducible data. The variation of the viscosity ? with absolute temperature T is adequately expressed by Andrade's exponential relationship ?V1/3 = AeC/VT , where A and C are constants and V is the specific volume of the liquid. The values of A and C are given as 2.485 x 10-3 and 20.78, 2.444 x 10-3 and 88.79, and 2.169 x 10-3 and 239.8, respectively, for mercury, lead, and zinc. The error of measurement is assessed to be about 1 pct. Prefreezing phenomena in the vicinity of the freezing point of the zinc samples were found to be absent. AS part of an over-all program of research on various phases of melting and casting nonferrous alloys, a systematic study of some physical properties of liquid metals and their alloys was undertaken in the laboratories of the Physical Metallurgy Division.1,2,3 The most recent phase of this work, on zinc and some zinc-base alloys, was carried out in cooperation with the Canadian Zinc and Lead Research Committee and the International Lead-Zinc Research Organization. One of the properties investigated was viscosity and the present paper gives results on pure zinc; the second part, on the viscosity of some zinc alloys, will be reported separately. Experimental interest in the viscosity of liquid metals has virtually been confined to the past 40 years. The capillary technique was already established as the primary method for the viscosity of fluids in the vicinity of room temperature; all relevant experimental corrections were known and an absolute accuracy of 1 to 2 pct was possible. Ap- plication of the capillary method to liquid metals creates a number of exacting requirements to manipulate a smooth flow of highly reactive liquid through a fine-bore tube. Consequently, the degree of precision usually achieved in the high-temperature field rarely compares with measurements on aqueous fluids near room temperature. However, the full potential of the capillary method has yet to be explored using modern experimental techniques. As an alternative, many investigators in this field have preferred to select the oscillational method. Unfortunately, the practical advantages are somewhat offset by the inability of the hydrodynamic theory to realize a rational working formula for the calculation of the viscosity. In attempting to overcome this restriction many investigators have employed calibrational procedures, even to the extent of selecting an arbitrary formula for use with a given shaped interface. However, where calibration cannot be founded on well-established techniques, the contribution of such experiments to the general field of viscometry is questionable. A critical appraisal of the viscosity data existing for pure liquid metals reveals a somewhat discordant situation where considerable effort is still required to establish reproducible and reliable values for the low-melting point metals. The means of rectifying this situation have gradually evolved in recent years. Here, the theory of the oscillational method has undergone major advances for both the spherical and cylindrical interfaces. The basic concepts of verschaffelt4 governing the oscillation of a solid sphere in an infinite liquid have been adequately expressed by Andrade and his coworkers.5,6 Employing a hollow spherical container and a formula, which had been extensively verified by experiments on water, absolute measurements on the liquid alkali metals were obtained. The extension of this approach to the more common liquid metals has been demonstrated by culpin7 and Rothwel18 where much ingenuity was used to surmount the problem of loading the sample into the delicate sphere. Because of the elegant technique required to construct a hollow sphere, the cylindrical interface holds recognition as virtually the ideal shape. On the other hand, loss of symmetry in one plane increases the complexity of deriving a calculation of the viscosity. The contributions of Hopkins and Toye9 and Roscoe10 have markedly improved the potential use of the cylindrical interface in liquid-metal viscometry. The relatively simple experi-

Jan 1, 1965

By P. H. Lindon, J. C. Billington

Fe-O melts containing 0.045 pct 0 were deoxidized with Mn-Si-A1 alloys. Product compositions were reluted to the melt and alloy compositions and were found to be most sensitive to the aluminum content of the alloy. Low residual oxygen contents could be obtained when aluminum oxide was present in the Products because of the reduction of silica and manganese oxide activities. Flotation of the Products from a quiescent melt was followed both by analysis of the oxygen content and metallographic measurement of inclusion concentration. MnO-SiO2-A12O3 products were found to float most rapidly when their composition was such that their viscosity may be expected to be low. Changes in the particle size distribution indicates that particle coalescence occurred and differences in the degree of coalescence are thought to be responsible for the different flotation rates observed between products 0f differing composition. Measured flotation rates were slower than those Predicted from a model based on Stoke's Law, although alumina flotation might be reasonably accounted for by this model. Interfacial effects between oxide particles and the melt are believed to be responsible for the discrepancy. It has been recognized that deoxidation products constitute a large proportion of the nonmetallic inclusions present in killed steel. The amount of oxide inclusions which originate as deoxidation products depends largely upon three factors. These may be summarized, according to P16ckinger1 as: 1) Amount of primary products remaining in the steel prior to cooling. 2) Residual dissolved oxygen content of the steel after deoxidation. 3) Amount of secondary products, formed during cooling and solidification, which remain entrapped in the solid steel. In a well-deoxidized steel containing residual aluminum and/or silicon, the equilibrium dissolved oxygen content is usually very low and so the maximum amount of oxide which may be produced as secondary deoxidation products is small in comparison with the amount of primary products. It may be seen, therefore, that the amount of indigenous nonmetallic inclusions may be minimized if a low dissolved oxygen content is achieved by deoxidation and if the primary deoxidation products are efficiently removed. Oxides which originate by reaction of the metal stream with the atmosphere during teeming are not considered in the present study. It is known that two or more deoxidizers may result in a lower equilibrium oxygen content when used in conjunction with one another than when any of the individual deoxidizers are used alone. Equilibrium studies by Hilty and crafts2 and by Bell3 have shown that manganese increases the effectiveness of silicon as a deoxidizer, and Walsh and Ramachandran4 relate this to a reduction in the activity of silica in the products as the manganese :silicon ratio in the steel increases. It was also shown by Herty's work on deoxidation of steel by silico manganese alloys,5 that there existed an optimum ratio of manganese to silicon which gave a minimum inclusion content. This ratio was in the range 4:l to 7:l and the (FeO-MnO-SiO2) products formed by such deoxidation practice were found to lie in a composition range having very low liquidus temperatures (1170 to 1250°C approx). The optimum manganese:silicon ratio was then explained by postulating that these fluid products were able to coalesce and that the larger particles formed floated out of the steel very quickly as predicted by Stoke's Law. The present work examines the effectiveness of various Mn-Si-A1 alloys as deoxidizers and their effects on the composition and removal of primary deoxidation products from a quiescent melt. EXPERIMENTAL TECHNIQUE Approximately 250 g of prepared Fe-O alloy, containing 0.045 to 0.055 pct O, were melted in an alumina crucible and deoxidized at 1550°C by plunging a thin steel cartridge containing the deoxidizer below the melt surface. A high frequency induction furnace supplying current at 8.5 kHz was used to heat a graphite susceptor, the interior of which had been machined to give a wall thickness of 0.85 in. to form a receptacle for the alumina crucible. The iron melt was essentially quiescent as the induced current was concentrated at the external surface of the graphite susceptor by the skin effect. A nonoxidizing atmosphere was maintained over the melt by passing a continuous stream of argon through the lid of the susceptor. The melt temperature was measured before deoxidation, and again at the end of an experiment by means

Jan 1, 1970

By J. L. Lehman, J. D. Sudbury, J. E. Landers, W. D. Greathouse

A full scale field experiment on cathodic protection of casing answers questions concerning (1) the proper criteria for determining current requirments, (2) the amount of protection provided by different currents, and (3) the transfer of current at the base of the surface pipe. Three dry holes in the Trico pool in Rooks County, Kans., were selected for cathodic protection tests. The three holes were in an area where casing failures opposite the Dakota water sand often accur in less than a year. Examination of the electric togs showed the wells to be similar to other wells in the field where casing in four of seven producing wells has failed. The three holes were cleaned out and cased with 75 joints of new 51/2-in. 14-tb J-55. Each joint was visually inspected and marked before it as run. The casing was bull plugged and floated in the hole 50 that the inside might remain dry and free of excessive attack. Also, if a leak occurred, a pressure increase could be observed on gawge at the surface. Extensive testing was done, including potential profiles, log current-potentid curves and electrode measurements from both surface and downhole connections. Based on these data, a current of 12 amps was applied to one well and 4 amps to mother. The third well was left to corrode. During the two-year period when the casing was in the ground, [he applied current was checked weekly, and reference electrode measurements were made about every two months. Three sets of casing potential profi1e.c were run. When the three strings were pulled, each joint was examined for type of scale formed, presence of sulfate-reducing bacteria, extent of corrosion nttnck and pit depth. Since the pipe was new when run, quantitative determination of the protection provided by current was possible. This is the first concrete field evidence to help resolve the many arguments about the proper method for selecting adequate current for cathodic protection of oilwell (-using. INTRODUCTION A casing string is run when a well is drilled. This pipe is supposed to protect this valuable "hole in the ground" for the life of the well. Often the casing does not last the life of the well; it is with these casing failures that this work is concerned. The cost of repairing a casing failure varies from field to field—from as much as a $30,000 per leak average in California to $5,000 per leak in Kansas. Additional costs other than actual repairs are also important. These include formation damage, lost production, etc. Casing damage caused by internal corrosion is important in some areas. Treatment normally consists of flushing inhibitor down the annulus, but further research is being done on control measures. The test described in this paper is concerned only with external corrosion. The problem of casing failure from external attack has appeared in several areas including western Kansas, California, Montana, Wyoming, Texas, Arkansas and Mississippi. Cathodic protection is currently being used in an attempt to control external corrosion. From reports in the NACE there are thousands of wells currently under cathodic protection. The quantity of current being applied ranges from 27 amps on some deep California wells to a few tenths of an amp being supplied from magnesium anodes on wells in Texas and Kansas. Considerable field and laboratory effort1,9,5,6 was exented on the problem of cathodic prctection of casing, and it became fairly obvious that this method could be used to protect wells. Early workers showed that current applied to a well distributed itself over the length of the casing and was not concentrated on the upper few hundred feet. Basic cathodic protection theory had shown that corrosion attack could be stopped by applying sufficient current. The problem resolved itself, then, into one of trying to decide just how much current was necessary. Various criteria were utilized in installing the many existing cathodic protection installations. These methods included the following. 1. Applying sufficient current to remove the anodic slope as shown by the potential profile." 7. Applying enough current to maintain all areas of the casing at a pipe-to-soil potential of .85 v.' 3. Applying the current indicated by a log current-potential (or E log I) curve." 4. Supplying the current necessary to shift the pipe to-soil potential .3 v." 5. Applying 2 or 3 milliamps of current per sq ft of casing."