Search Documents

By Masakazu Takano, Koji Suzuki, Naotoshi Shinkawa

"Cement deep mixing (CDM) method successfully applied to a marine construction project in northern Vietnam is reported. The method is classified as wet method, in which cement slurry is injected into the ground. Thickness of clayey deposit subjected to improvement is from 20 m to 28 m, and the total volume of CDM improvement exceeds 460,000 m3. This is the first massive application of CDM method in the region. Three CDM barges, each equipped with four mixing shafts, were brought to the site in order to finish CDM work within a period of seven months. Cement content used in the work was 180 kg/m3 and water-cement ratio of slurry was 100%. Unconfined compression strength of stabilized soil was 1,200 kPa to 1,600 kPa in average with coefficient of variation from 0.3 to 0.4. Statistics analysis of the strength with these values gave percentage of lower strength less than 10%. Trial use of needle penetration test performed to study strength profile of a CDM column is also reported.INTRODUCTIONThe site of Lack Huyen Port Infrastructure Construction Project is located in the sea adjacent to Cat Hai Island, offshore Hai Phong city which is around 100 km east of Hanoi, the capital of Vietnam. Left side of Fig. 1 shows the location of the site. The project contains development of container terminal, dredging of waterway, construction of sand protection dyke to prevent waterway from being buried, and bridge construction to connect the island to the mainland.Joint venture of Penta Ocean Construction and Toa Corporation was awarded Package 6 of the project, in which reclamation of container terminal area, retaining wall construction and terminal road construction were included. Plan of the site is presented in right side of Fig. 1. The site work has been started in June 2013 and is scheduled to finish within 4 years."

Jan 1, 2015

By Stephen Darmawan, Mahdi M. Disfani, Arul Arulrajah, Alireza Mohammadinia

Deep mixing using cementitious compounds is an in-situ method of ground improvement for improving the strength, compressibility of loose sand. Artificial light cementation can increase the stiffness of loose sands significantly and reduce the settlement of loose deposits. The increase in contact area between the particles with a thin layer of cementitious agent depends on the confinement and void ratio of the soil mass. Hence, the stiffening effect of cementation not only depends on the type and amount of cementing agent and inter-particular force chain of loose deposit but also depends on the stress level at the time of cementation. In addition, the cementation effect in loose deposits can be deteriorated at relatively low strain levels. Decementation softening can cause detrimental and irreversible impacts on the soil deposit. This study investigates the effect of initial confinement and subsequently the initial void ratio at the time of cementation on small strain behaviour and decementation softening of cemented loose sand under ko loading. The effect of inter-particular contact of sand particles based on the specific surface area and also soil density was also investigated by means of shear wave propagation. This study present insightful information on effect of primary consolidation stress levels, density of soil and cementation level on softening and collapse of loose deposits improved using deep soil mixing technique. Better understanding of soil-cement interaction by optimization of binder content for deep mixing activation can lead to increasing the level of confidence in using this technique in ground improvement applications.

Jan 1, 1900

By Nicolas Denies, Jeroen de Leeuw, Bart Lameire, Jan Maertens, André Vervoort, Flip Hoefsloot, Noël Huybrechts, Flor De Cock

"In recent years, the Deep Mixing Method has increasingly been applied for the construction of earth and water retaining structures. From practice, it has been experienced that there is a real need to develop execution and design rules adapted to the function of the soil mix wall (retaining wall, water barrier, foundation solution or a combination) including the temporary or permanent character of the application. Based on the results of the BBRI Soil Mix project (2009-2013), a design approach has been developed in collaboration with the SBRCURnet. The present paper briefly discusses the principles of this design approach which takes into account the function of the soil mix wall and the characteristics of the soil mix material. The interaction between the soil mix material and the steel reinforcement can be considered in the calculations depending on the function of the soil mix wall. Design and quality control requirements are given in function of the application and take the lifetime of the structure into account. Durability aspects of the soil mix material are therefore considered in the present design approach.INTRODUCTIONSince several decades, the deep mixing method is used for ground improvement works. A more recent application is the use of soil mix as structural elements such as in the case of the earth-water retaining soil mix walls. Since 2000, due to the economic and environmental advantages of the method, this particular application has shown an amazing growth in Belgium and in the Netherlands. A typical excavation (16 m depth), realized with CSM (Cutter Soil Mix) panels, is shown in Fig. 1. For temporary applications, the questions related to the mechanical characteristics of the material, its permeability and its adherence with steel have been investigated with success within the framework of the BBRI Soil Mix project (2009- 2013) (see Denies et al. 2012 for more details). The durability of the soil mix material remains a complex topic while permanent applications are more and more observed in practice. In order to define an obvious design approach, it was necessary to clarify the potential functions of soil mix walls and to establish the requirements related to their design and construction. The BBRI (in Belgium) and SBRCURnet (in the Netherlands) have therefore worked together to publish guidelines in the form of a handbook titled ‘Soil Mix Walls’ (publication foreseen in 2015). In this handbook, a methodology is proposed for the design of the soil mix walls for which the interaction between steel and soil mix can possibly be taken into account dependent upon the application. Each potential function of the soil mix wall is described (e.g. earth retaining wall, cut-off wall, etc.) and the temporary or permanent character of the application is always considered."

Jan 1, 2015

By Les R. Chernauskas

Driven pipe piles are commonly used for near and offshore structures due to their omni-directional bending resistance, large surface area, and ease of installation. However, these piles typically cannot be driven deep enough to develop significant and sustained uplift capacity, and in some cases do not generate enough end-bearing resistance before being overstressed during driving. When driven closed-ended, their relatively light weight to cross-sectional ratio, and when driven open-ended their tendency to prematurely plug, are some installation short comings. Spin Fin® piles are traditional pipe piles fitted with flat, steel plates (?fins?) attached at a slight angle over the lower few feet of the pipe. Their design development dates back several decades for projects associated with harsh, limited weather window, offshore Alaskan oil field work. These projects required a pile type that could generate high and sustained capacity in both compression and tension, at relatively shallow depth. During pile driving, a relatively short, high capacity pile translates into more rapid installations with smaller and more efficient equipment. In this type of environment, where pile capacities are large, cyclic loading is typical, and relatively high pile movement is tolerable, the Spin Fin® pile is a superior solution. This paper describes the experience of using Spin Fin® piles on several recently completed Massachusetts Steam Ship Authority projects.

Jan 1, 2011

By Peter Faust, Peter Hubbard, Kenichi Soga

The European Federation of Foundation Contractors (EFFC) and The Deep Foundations Institute (DFI) have set up a task group to compile a Guide for Working Platforms. The first edition of this Guide has been published in January 2020. The aim of the Guide is to provide reliable methods for design, testing and verification of working platforms for construction equipment, especially in the deep foundation industry where track loads can be excessive due to the nature of its operations. The Guide has identified areas where knowledge is limited. Actual track pressure and its distribution along the length of the tracks is still not well researched. Current recommendation provided in EN 16228-1 are believed to be overly simplified and may lead to conservative requirements for working platform thickness. This paper presents results of a series of field tests where the actual track pressure of a large drilling rig during operation was measured in real time together with the deformation of the working platform. Embedded, distributed fiber optic sensing (DFOS) at different depths throughout the platform allowed for a three-dimensional evaluation of the platform deformation throughout the entire operation. Results will help to develop more reliable recommendations for future safety requirements of working platforms for deep foundation equipment.

May 1, 2022

By Nick Hytiris, Mohammed Al Maadheedi, Slobodan B. Mickovski

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Mohammed Al Maadheedi

This paper explores the capacity effects of a square steel plate welded at the ground surface on a driven open-ended steel pile (i.e. the plate would touch the ground surface after the pile achieves the required penetration). A series of strain-controlled, 1-g laboratory tests were undertaken on piles with and without a square steel plate attached. The piles were driven in dry, loosely packed, uniform sand. Two plates were used, one with a breadth equal to two times the diameter of the pile (2D) and the other with a breadth equal to three times the diameter of the piles (3D). A 20% increase in capacity was recorded for the 2D plate, and a 110% increase in capacity was recorded for the 3D plate when compared to the pile without an attached steel plate. The back-analysis of the results allowed the derivation of a new expression to calculate the capacity of bearing plates, which accounted for the effects of sands compaction and dilation. By extrapolating the findings of these tests to a hypothetical scenario, a model design problem was described where the length of a pile can be reduced by 20% to 60% (depending on the load) by using a plate attached to the pile. The results of this study can help designers to minimise penetration depth; thus, achieving a more economical and sustainable design.

By Tsuyoshi Honda, Kazuhiro Kaneda, Masayuki Imai, Kazuo Konishi, Kunio Higashinaka

"In recent years, the demand for measures to control liquefaction of existing airport runways and harbor structures has increased. However, from the perspectives of constructability and cost, application of grid-form deep mixing walls to these types of structures requires the formation of wider grid spacing as compared with conventional designs. In this research, we focused on the extent of liquefaction and ground surface settling when grid spacing is made wider than conventional designs. We conducted centrifuge model tests, and confirmed the liquefaction suppression effect when grid-form modifications involving wide grid spacing are adopted under asphalt pavement. The tests were conducted under conditions that included changing the grid spacing and groundwater level. When the groundwater level was high, an increase in water pressure was observed, even within the grid. However, when the groundwater level was low, the increase in water pressure inside the grid was suppressed. We also found that if the generation of water pressure can be suppressed, the amount of settling due to liquefaction can also be controlled.INTRODUCTIONOne construction technique used as a countermeasure to liquefaction is grid-form deep mixing walls. Grid-form deep mixing walls are a construction technique for which improved grid-shaped wall bodies are built into the ground below the surface using a deep mixing method. This construction technique minimizes shear deformation by surrounding liquefied ground with improved wall bodies, thereby preventing liquefaction (Fig.1). With conventional designs, grid-form deep mixing walls determine the grid spacing that can deter liquefaction based on a ratio of the grid spacing L to the improved depth H (ratio = L/H). Ordinarily, designs are implemented with an L/H ratio of 0.8 or less (PWRI, 1999).In recent years, a demand for measures to control liquefaction of existing airport pavement and harbor structures has increased. However, when liquefaction countermeasures are implemented at these types of facilities and structures, the construction work must be implemented while the facilities and structures remain in service. Therefore, temporal and spatial constraints must be considered. In addition, unlike conventional liquefaction countermeasures, performance requirements are such that, even if some degree of liquefaction is allowed, the performance is acceptable as long as the amount of settlement is within a predetermined value. Therefore, if grid-form deep mixing walls are applied to these structures, grid spacing that is wider than conventional standards is desired."

Jan 1, 2015

By Karen Dawson

Pressure-grouted helical piles support a new seven-story homeless housing center in the Coney Island neighborhood of Brooklyn, New York. The project team instrumented and statically load tested piles to as much as 1,000 kips (4.4 MN) in advance of construction to obtain the approval of the New York City Building Code officials and to verify the design. Use of pressure-grouted helical piles required additional design effort and time risk because of New York City's Construction Code Determination (CCD1) process, which is required for non- standard deep foundation types. Despite

May 1, 2022

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By Kenton W. Braun

Concourse B at the Anchorage, Alaska International Airport is currently being renovated while retaining the original building structure and foundations. Part of the renovation includes the installation of a new, permanent baggage tunnel system beneath the existing building. Installation of this cast in place concrete tunnel, beneath the existing structure, required installation of a steel retaining wall to support footing loads above the base of the excavation. Construction of this retaining wall presented challenging and unconventional design and construction methods. Detailed discussions of the design and construction techniques utilized for this project are outlined.

Jan 1, 2008

By Walter Kaeck

In a recent upgrade of their system, Amtrak converted a bascule type draw bridge over the Thames River to a vertical lift structure supported by the existing piers. During the bridge replacement, significant settlement occurred on one of the piers and movement continued thereafter. Construction was stopped as Amtrak became concerned as to how much the subsequent construction activities would cause the pier to further settle and tilt, not only impacting the operation of the existing bridge, but also jeopardizing the new lift span. Mueser Rutledge was engaged at this time to help understand and solve the problem. A remedial grouting program was developed to arrest the settlement. As a subcontractor to Cianbro Corporation, Pittsfield, ME, The Judy Company was hired to perform the remedial grouting work. Work platforms were constructed around the pier for support of the drilling equipment. A dual string drilling system was used to install sleeve pipes at depths of up to 185? below the water level. Ultrafine cement grout stabilized with additives was placed at 2.5 foot intervals through the depth of the sand and gravel stratum below the bottom of the pier. Logistics were difficult and the schedule was severely impacted by the remedial work, necessitating working six 12-hour shifts per week and working in the river through the winter months. After four months of drilling and grouting, movement of the pier stopped. At the conclusion of the remedial work, more than a million gallons of ultrafine cement grout were placed. Confirmation borings recovered completely solidified material with compressive strengths ranging from 500 to 1500 psi. The bridge replacement was then completed and is functioning. Continued monitoring through July 2009 shows negligible movement.

Jan 1, 2009

By Lok M. Sharma

Development of brownfields is of great interest in these days. Such fields are not easily adaptable for foundations of structures. The uncertainties in ground behavior present challenges of unpredictable subsidence that could be detrimental to the build up facility. A desalination plant had to be located along the seashore, close to the needy population and the existing water supply infrastructure. The available site had been developed as a recreational park area over a dumped construction demolition debris landfill along the coastline. To construct a desalination plant comprised primarily of large concrete basin tanks on slab, founded on the debris fill had its challenges. A ground improvement system in the form of vibro replacement stone columns was designed and constructed. Approximately 5,000 stone columns were installed across the site. This paper describes the analysis process, the design, field load testing, and installation of stone columns. Difficulties during construction and monitoring aspects are briefly described. The plant started operations in the summer of 2008 and to date has performed satisfactorily. When properly designed, the development of brownfields is achievable at other sites.

Jan 1, 2009

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By Nick O’Riordan, Kaitlyn L. Fleming, Michael Riemer, Youssef M. A. Hashash, Stephen McLandrich, Mohamad Jammoul, Pierre Gouvin, Andrew Yeskoo

"To accommodate urbanization, cities are developing more underground space as a means to house public transportation systems and other entities. Underground developments often require construction of deep excavations in an environment dense with infrastructure. The success of such a project is related to the amount of impact imposed on adjacent structures and economic activity; impact should be limited to insignificant amounts in order to mitigate damage and disruption. Thus, large-scale urban construction projects require extensive monitoring of ground movements and installed support performance to facilitate informed decisions for adjustment of construction activities and support design when necessary.In downtown San Francisco, a unique large-scale excavation in saturated soft soils was constructed for the Transbay Transit Center (TTC). Construction of the excavation began in April 2012 and was completed almost two years later in February 2014. To monitor ground and structure response to construction, the project team used an extensive instrumentation network that included automatic inclinometers, piezometers, strain gages and total stations paired with survey markers. Innovative imaging techniques developed a record of construction in order to relate measured deformations to construction activity.Transbay Transit CenterThe Transbay Transit Center (TTC) is being constructed as a modern day transportation hub in downtown San Francisco to replace the former Transbay Terminal. The project is located in the South of Market area, less than half a mile from the San Francisco Bay. The final center will connect eight counties in the Bay Area through 11 different transportation systems, some of which will be housed in the TTC including Caltrain, Golden Gate Transit and California High Speed Rail. The aboveground structure will consist of two levels for retail and a third level with a bus terminal beneath a rooftop garden. There will be two subgrade levels to serve as a lower concourse and the train platforms. This structure required construction of a deep excavation closely surrounded by buildings and roads in an area thriving with economic activity."

Jan 1, 2015

By Dempsey S. Thieman

Innovative marine bulkhead design and construction techniques were used in the fast-track design and construction of a high-capacity, deep-water dock in the highly seismic region of Alaska?s Aleutian Islands. The geotechnical investigation and design through construction phases were completed in just eight months. The adaptable OPEN CELL® design, readily available standard flat sheet pile and an experienced contractor were integral to the successful completion of the project. The cost of the structure was determined to be approximately 50 percent of a comparable pile-supported platform dock structure, allowed higher load capacity, rapid construction, less maintenance, and provided substantially more uplands. This paper details the design and construction of this unique and challenging project. The OPEN CELL structure is a vertical flexible membrane system that offers significant advantages over other structure types: ? Its flexible membrane structure is not dependent on toe embedment for stability. ? Poor soil conditions, shallow bedrock, high seismic loads, deep water, scour, etc., can be accommodated due to its adaptable design. ? It has a very high load capacity?capable of several thousand pounds per square foot. ? Allows buried utilities which results in lower cost and reduces freezing conditions ? The sheet pile tail walls can be extended to provide increased global stability if needed. ? Standard sheet pile and connectors with traditional installation techniques allow accelerated construction schedules.

Jan 1, 2008

By Stephan A. Jefferis, Adrian H. Bath

"This paper draws together some themes on the durability of barrier systems, and particularly cementitious systems. For contaminated land and water retaining structures, durability can be poorly addressed at all stages of a project, from specification, to barrier material selection, barrier design including toe-in and through to performance assessment in operation. Permeability (hydraulic conductivity) is a dynamic property which will vary over time as reaction processes propagate through a barrier. However, laboratory testing, when undertaken, tends to be focused on short term tests with aggressive chemicals so that the effects of longer-term processes such as carbonation and leaching by permeating water are missed. For water retaining structures, carbonation and leaching actually may be the most significant processes affecting barrier performance as the groundwater adjacent to many water bodies can be otherwise rather benign (as regards bentonite and cementitious systems). These and other reaction processes have been modelled in the arena of nuclear waste repositories and procedures are well recognised. However, such procedures have yet to be widely adopted for the assessment of other barrier systems.INTRODUCTIONOver the last few decades there has been an enormous amount of laboratory research on the durability of barrier materials or more specifically papers reporting the results of permeability tests. Unfortunately there is a much smaller literature on scaling test results to barrier dimensions in the field or to required design lives. Although in the geotechnical industry durability research has been largely laboratory based, in the nuclear industry where relevant timescales are multi-millennia rather than decades, research has been heavily underpinned by geochemical modelling. A significant purpose of this paper is to examine the tools that may be used to analyse the results of tests on barrier materials used in geotechnical engineering, for example, for water retaining structures and contaminated land and draw the attention of the construction industry to the potential of the modelling procedures developed for nuclear repository assessments. Modelling can help to identify underlying processes and so augment information from laboratory testing focused on changes of physical properties such as permeability and strength."

Jan 1, 2016

By S. R. Nandargikar

Construction of open foundations for the Second Thane Creek Bridge was indeed a challenging task. Some major problems were encountered during the construction of foundations for pier No. P22 (S/N), P.6(S) and P.12(S) of this bridge. This paper describes these problems briefly and also highlights how they were solved.

Jan 1, 1996

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By Jeremy G. Kress

We propose the discrete element method (DEM) as a complimentary alternative to analytical solutions and FEM models for the analysis of pile response. DEM is a novel approach to the engineering design of deep foundations which can be used to provide insight into the mechanics of soil-soil and soil-structure interaction. It is common to use analytical, empirical, and semi-empirical methods to predict pile behavior, where if granular properties, pile length, or load orientation change, then significant adjustments are made in the design sequence. DEM provides a more uniform approach in granular soils. Based on constitutive force-displacement relationships and laws of motion in rigid and elastic bodies, few changes must be made for a wide variety grain types, pile types, embedment, and load orientation. Preliminary results for simulation of a single pile are qualitatively consistent with results from conventional design procedures and also provide significant information not available from other analyses (e.g., local information about interface failure during shear). Importantly, these analyses are portable to a variety of pile types and installation procedures, which may not be the case for empirical approaches. Given consistent increases in computing power and rapid advances in model speed and sophistication, the DEM should prove to be a robust method for design and the analysis of pile response in granular soils.

Jan 1, 2010