Search Documents

By Irving Fatt, R. M. Weinbrandt

Efforts have been made for many years to observe pore structure of sedimentary rocks on a microscopic scale. A better description of the pore structure in reservoir rock would aid in the development of relations between flow through tube network models and flow in consolidated reservoir rock. The unique qualities of the scanning electron miscroscope (SEM) make it the ideal tool to use in a study of pore structure. Previous methods of studying pore structure included plastic casts of pore space and optical microscopy.l-7 There is now available a new method to observe three-dimensional flow channels in reservoir rock: a scanning electron microscope having variable magnification from X20 to X20,000 and approximately 1000 times the depth of focus of the conventional light microscopes. This microscope also can obtain stereoscopic images and can measure and diagram flow channels so that it is possible to construct a network of tubes that will model consolidated reservoir rock. THEORY OF THE SCANNING ELECTRON MICROSCOPE The scanning electron microscope (SEM) functions by projecting a beam of electrons through magnetic focusing lenses at a specimen and recording secondary electrons excited by the primary beam. The amount of secondary electron emission portrays the topography of the specimen because more secondary electrons are emitted from high points than from low points. A schematic of the SEM is shown in Fig. 1. The property of the SEM that is of most importance in this study is its great depth of focus. The depth of focus results from using electrons

Jan 1, 1970

The Library of the above-named Societies is open from 9 A.M. to 10 P.M. on all week-days, except holidays, from September 1 to June 30, and from 9 A.M. to 6 P.M. during July and August. The-Library contains about 55,000 volumes, including sets of technical periodicals and the publications of scientific and technical societies. Members of the Institute, with few exceptions, are forced to spend .a portion of their time in localities isolated from sources of information. To these the Library can render valuable service through correspondence; letters requesting information will receive special attention. The Library is prepared to furnish references and copies of articles on mining and metallurgical subjects; to determine the existence of mining maps, and to furnish general information as to the geology and mineral resources of all countries. All communications should be made as definite as possible so that the information received may be what is desired and not include collateral matter which may not be of interest. The time spent in searching for such collateral matter will be saved, and the information will be sent more promptly and in more usable shape. The members of the Institute can be of service to the Library by forwarding copies of mining reports maps privately issued, and similar material, which will he classified, indexed, and made available to other members. Suggestions for additions to the Library, either by purchase or personal solicitation as gifts, will be welcomed. It is hoped that members while in the city will use the Library freely, and. assurance is given that most careful service will be rendered to them.

Jan 6, 1915

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

By Thomas F. McLoughlin, David K. Hylbert

A new method of satellite imagery analysis has been developed during underground mine roof research. Landsat positive film transparencies were projected onto topographic base maps to scale and lineaments enhanced with a Ronchi grating (method A). Thirty-five millimeter slides of video-enhanced scenes were also projected onto base maps (method B). Both methods permit direct plotting of lineaments to scale and direct correlation with surface and subsurface data wing transparent overlays.

Jan 1, 1981

By R. D. Pehlke, J. F. Elliott

The equilibrium pressure of nitrogen gas over pure silicon metal and silicon nitride has been measured in the temperature range 1400° to 1700°C. From the experimental data, the standard free energies and enthalpies of formation of Si3N4(a) have been calculated as functions of temperature over the above temperature range. Utilizing data in the literature and the results of this investigation, the specific heat, molar enthalpy, molar entropy, standard enthalpy of fornation, and standard free energy of fornation are estimated for the temperature range 298° to 1400°C. THE high-temperature thermodynamic properties of many metallic nitrides are not well established at present. This is a serious deficiency because nitrogen and nitride-forming metals are important alloying additions to steels, and knowledge of the interaction between nitrogen and these elements is essential to a better understanding of the behavior of steels. Metallic nitrides also are used as refractory materials. Consequently, the investigation reported here was undertaken to provide more complete information on the standard entropy and free energy of formation of silicon nitride. The experimental technique provided a direct measurement of the equilibrium pressure of nitrogen gas in the range of 1413 to 1700°C for the reaction: 3 Si(1) + 2N2 (g) = Si3N4 (a) [ 1 ] and below 1413oC for the reaction: 3Si(c) + 2N2(g) = Si3N4(a) [2] APPARATUS The experimental system consisted of a crucible assembly, a reaction chamber, and a gas supply and vacuum system. The Crucible Assembly which contained the equilibration specimen and molybdenum radiation shields with a susceptor for induction heating is shown in Fig. 1. Two covered, high-purity alumina crucibles, one nested within the other, contained the susceptor, shields and specimen. Central openings in the upper shield and crucible covers permitted on optical pyrometer to be sighted into the central cavity of the specimen. The specimen itself was a 5/8 OD by 1-in.

Jan 1, 1960

THE metal iron has physical and chemical properties which are somewhat different from those of steels, but a knowledge of the pure metal is a useful starting point in studying the behavior of steels. Solid iron exists in two different crystalline forms, called alpha (a) and gamma (?) iron, the former being the ordinary form at room temperature. When heated above the "A2 point," 768 C (1414 F), the metal becomes nonmagnetic, and at the "A, point," 910 C (1670 F), it undergoes a change in crystalline form to become gamma iron. In the range 768 to 910 C, it is sometimes called beta (ß) iron to distinguish it from the magnetic alpha, but the two are identical in crystal structure. When gamma iron is further heated to 1400 C (2552 E), it changes into delta (d) iron, which is identical with beta or non- magnetic alpha iron. Pure iron melts (in an inert atmosphere) at 1537 C (2800 F); the melting point is generally lowered by alloys or impurities. PROPERTIES OF IRON AT HIGH TEMPERATURES Many of the properties of iron undergo abrupt changes at the transition temperatures.1 For example, in heating through the A, point, a sudden shrinkage in volume occurs. Similarly, melting is attended by sharp physical changes such as an increase in volume. Table 16-1 contains a summary of the measured physical properties of pure iron at several temperatures. Usually the properties change smoothly within the range of stability of a given form, but this is not always true. For example, the specific heat reaches a sharp maximum at the A2 point although no trans- formation occurs. (See Fig 14-1.) Solvent Powers of Liquid Iron. Liquid iron is capable of dissolving most of the other metals and many nonmetallic elements as well. Of the metals that are liquid at the melting point of iron, only lead, silver, and bismuth refuse to dissolve to an ap-

Jan 1, 1951

New Products Equipment

Jan 11, 1950

By George Comstock

Results are given of scleroscope and Brinell tests on specimens of cast 10-per cent. aluminum bronze, quenched and reheated at various low temperatures. The scleroscope was not found as reliable as the Brinell machine for measuring the hardness, for the size of the piece tested seemed to affect the scleroscope results. The maximum hardness was obtained by quenching and reheating to between 315° and 370° C. Softening was produced by reheating above 370° or 400° C. A series of polished and etched microsections showed a more reddish color in those that had been reheated above 400° C., and a change in microstructure above 500° C. IT HAS been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10-per cent. aluminum bronze, quenched for maximum hardness, and subsequently annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10-per cent. aluminum bronze at 400° C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature was necessary to obtain any softening effect.

Jan 7, 1924

By Leland Russell van Wert

In 1888, Howard,1' working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200" to 350" C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.~ He described (for nonaustenitie steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300" C., or below 200" C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200" to 300" C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200' and 300" C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity, if nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931

By Günter Petzow, Siegfried Steeb

DURING an investigation of the U-Co-A1, U-Ir-A1, and U-Ni-A1 ternary systems, three previously unknown phases have been identified which correspond to the phases UCoA1, UIrA1, and UNiA1, and which be- long to the C22 (Fe2P) type (P 6 2m). In the following the structure determination of the new ternary phases is reported. The alloys have been prepared in an arc furnace under purified argon from 99.97 wt pct U, 99.83 wt pct Co, 99.99 wt pct Al, 99.95 wt pct Ni, and 99.97 wt pct Ir. The pellets obtained were bright and brittle; chemical analyses agreed with the nominal compositions. To obtain equilibrium, the samples were annealed in evacuated quartz capsules at 950°C for 30 hr and then quenched in water. Guinier photographs were processed and evaluated according to a method already described previously.1,2 The hkl's, measured and calculated sin2 6 values, and in the case of UCoAl only calculated and estimated intensities, are given in Tables I to 111. Lattice parameters refined according to the least-squares method and the respective mean-square variations are presented in Table IV. Lattice parameters, especially the c/a ratio, lead to the assumption that the three phases are crystallizing in the C22-type structure. For the calculation of the intensities given in Table I, the atomic positions recently reported by wyckoff3 have been accepted for the C22 (Fe2P) type. The uranium atoms were assumed to be in phosphorus sites; furthermore the scattering amplitudes of the boron atoms have been averaged in the stoichiometric formula UB2 according to atomic percentages; i.e., for these atoms a statistical distribution on the iron sites was assumed. The two smallest distances between a uranium and

Jan 1, 1967

By Leland Van Wert

IN 1888, Howard,1 working at the Watertown Arsenal on the tensile properties of ferrous materials at various temperatures, noted the curious fact that the stress-strain diagrams of low-carbon steels tested within a certain temperature range (200° to 350° C.) departed more or less from the normal regularity of such diagrams as secured by testing at either above or below these temperatures. This same jagged appearance of similar diagrams for steels has been observed by at least one other investigator, and de Forest2 has reported similar irregularities in the tensile testing of some nonferrous alloys. Recently again, this anomaly in diagram contour has been shown in a most striking fashion, apparently because of its accentuation by the method of testing employed, by Dr. Albert Sauveur.3 He described (for nonaustenitic steels) two quite distinct types of torsional stress-time diagrams: (1) those with a regular and smooth outline, derived normally by testing at temperatures above 300° C., or below 200° C. (as, for example, Figs. 4a or e); and (2) those presenting a decided "stepped" appearance, which are invariably produced when twisting is done within the 200° to 300° C. range (examples, Figs. 5a and b). The torsion test brings out so much more sharply (and convincingly) the irregularities occurring at 200° and 300° C. than does the tensile test that they can no longer be considered as resulting from simply idiosyncratic or accidental and inconsequential causes. Clearly, from the temperatures involved, the "stepped" type of diagram, or more accurately, the peculiar manner of response to torsional stress which manifests itself in the diagram, is an aspect of the "blue-heat" phenomenon. One's curiosity if, nothing else, prompts an inquiry as to the nature and significance of these "steps." What do they mean? What causes them? To these questions there are no completely satisfactory answers. The following experimental observations are offered as suggestions towards the solution of the problem.

Jan 1, 1931

Discussion of the paper of L. C. MORGANROTH, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 93, September, 1914, pp. 2345 to 2352. D. T. DAY, Washington, D. C.-I would like to hear some further detail as to the California deposits. L. C. MORGANROTH, Pittsburgh, Pa.-We have examined the California deposits at various times; I have been over practically all of them myself. These deposits are all of the massive variety. While it is possible that it could be mined and used for metallurgical purposes, it is not feasible because it costs too much. At the present time magnesite which is mined in California is used in the making of plaster, or by the paper trade. Careful figures show that if the California magnesite could be delivered to Atlantic seaports in the crude state at not over $4 a gross ton, and assuming that it would give the same results as the Austro-Hungarian magnesite, it would be cheaper to use the latter. It is also more difficult to dead-burn the massive magnesite, for while it starts to give up its gas readily, the difficulty consists in driving off the last few per cent., and unless this is driven off the magnesite will absorb C02 from the air, so that in a few months it may have 10 or 12 per cent. DAVID T. DAY.-How is the Austro-Hungarian supply at the present time ?

Jan 4, 1915

The following is an incomplete list of members and guests who called at Institute headquarters during the period Sept. 10, 1919, to Oct. 10, 1919. L. D. Anderson, Salt Lake City, Utah. P. S. Matthews, Newark, N. J. Ray J. Barber, New York City. A. Poole Maynard, Atlanta, Georgia. L. A. Barton, Major U. S. Engineers. L. J. Mayreis, Jamshedpur, India. J. A. Battle, Chicago, 111. Benj. L. Miller, Bethlehem, Pa. R. W. Bissell, New York City. Geo. D. Morgan, Bartlesville, Okla. Gilman E. Brown, Shanghai, China. A. C. Munroe, El Paso, Texas. Stanley Brown, Chuquicamata, Chile, Paul I. Norton, Jr., Columbus, Ohio. S. A. Walter G. Perkins, Stanford University, Norman Carmichael, Clifton, Arizona. Cal. Richard H. Catlett, Newark, N. J. Fred S. Porter, Seattle, Wash. Roderic Crandall Charles E. Prior, Cherry Creek, Nevada John J. Croston, Atlanta, Georgia. G. M. Richards I. N. Dally, Seattle, Wash. Gilbert Rigg, Melbourne, Australia. A. Faison Dixon, New York City. Pierre H. Sauvajol, Paris, France. Walter Dobbins, Springfield, Ill. Carl Scholz, Chicago, Ill. Foss E. Douglass, Rancagua, Chile. Ellsworth H. Shriver, Marysville, Ohio. H. S. Emlaw, Grand Haven, Mich. Harvey B. Small, Magangue, Colombia. R. S. Everet, Barre, Mass. Henry B. Smith, New Britain, Coma. H. W. Gipp, Melbourne, Australia. J. T. Smoody, Cornwall, Pa. F. A. Glass, Brainerd, Minn. S.. J. Speak, London, England. C. D. Grier, New York City. D. R. Thomas, New York City. James L. Head, Rancagua, Chile. Kirby Thomas, New York City. Geo. B. Holderer, New York City. R. M. F. Townsend, Washington, D. C. W. Spencer Hutchinson, Boston, Mass. Carl J. Trauerman, Helena, Mont. Henry Jequier, Paris, France. A. C. Veatch, London, Eng. L. W. Kemp, Chuquicamata, Chile. Myron R. Walker, Pittsburg, Pa. Herbert S. Kohlberg, El Paso, Texas. Curtis C. Webb, New York City. H. M. LaFollette, La Follette, Tenn. James Wilding, San Francisco, Cal. Richard Lamb, New York City. S. H. Zimmerman, New York City.

Jan 11, 1919

By A. U. Seybolt

A. U. Seybolt (General Electric Research Laboratory)— As pointed out in an earlier paper,41 it appears to be very difficult to nucleate Si3N4 in Si-Fe of silicon content up to around 5 pet. Therefore, one observes, as did Pearce, that equilibrations with nitrogen gas yield only nitrogen in solid solution at temperatures above about 700°C, or, as Pearce found, 770°C. Evidently, the free energy of formation of Si3N4 only becomes high enough at -770°C to overcome the reluctance of Si3N4 to nucleate. However, as mentioned in Ref. 41, if some Si3N4 is first formed by a mixture of ammonia and hydrogen, one can then replace this gas mixture by nitrogen gas, and either increase or decrease the amount of Si3N4 present at any temperature by suitable adjustment of nitrogen pressure: that is, to equilibrate with Si3N4. In the equilibration experiments cited in Ref. 41, equilibrium was approached from both sides, and it was found that samples up to 944oC, at least, were in equilibrium with Si3N4. Higher temperatures were not employed, as this would have necessitated a redesign of the apparatus for using nitrogen pressures in excess of 1 atm. To summarize, the results of Pearce's experiments and those of Ref. 41 cannot be directly compared because two quite different equilibria were studied. Therefore, the statement by Pearce on p. 1398 indicating apparent error in Ref. 41 is unjustified. M. L. Pearce (author's reply)— There was limited evidence obtained in the current investigation which would indicate that excessive "supercooling" did not occur. A small piece of the same resulting from heat treatment No. 5 in Table III was subsequently held at 800°C for 16 hr in 95 pet N-5 pet H. Isotope-

Jan 1, 1964

By Sir Robert Hadfield

Table 1 gives the composition of the specimens listed by the author. The details of test procedure and the results of the tests on mechanical, magnetic and electrical properties and cor-rodibility of the alloys are published in full in a paper by the same author, "Alloys of Iron and Manganese Containing Low Carbon," presented before the Iron and Steel Institute (of Great Britain) and published in full in their Proceedings for 1927, to which reference should be made. After reporting these tests the author gives the following discussion of results:] The studies here reported do not indicate that any of the series has really valuable or useful qualities for industrial applications, though the demands of industry are so varied that it is unsafe to prophesy that no special use will be found for a given material. The non-magnetic property of manganese steel is due to the association of Fe and Mn, but carbon has also an effect, enabling non-magnetic qualities to be obtained with a much lower percentage of Mn than would otherwise be the case; for example, 16 per cent. Mn is necessary for alloys practically free from carbon, while with 1 per cent. C nonmagnetic alloys may be obtained with as little as 7 per cent. Mn. Carbon, however, is the prime cause of the development of magnetic qualities by heat treatment. (Sec section 8 of the paper referred to above.) These Fe-Mn alloys show a resistance up to 87 microhms per c. c., but. as there are other alloys which have a resistance as high as 130 microhms per C. c., this does not provide any new feature of value. The most marked feature of the series studied is the brittleness in the range 3 to 10 per cent., with a maximum of brittleness at 7 per cent. Material with this percentage, while possessing quite appreciable hard-

Jan 1, 1927

By L. R. Raymond, J. L. Hudson

This paper proposes a comparatively short-term (8 to 10 hours) well test for detecting and characterizing well-bore damage and for measuring mean formation permeability. The proposed test is made by injecting fluid at constant pressure, recording injection rate as a function of injection time. After one to four hours of injection, the well is shut in and fall-off of bottom-hole pressure is obtained as a function of shut-in time. Formation permeability is estimated by an iterative technique. First, a value of formation permeability is assumed. Then, a plot of the recorded injection rate as a function of dimensionless time is made, using the assumed pertneability value. From the slope of the injection-rate curve. a new value of formation permeability is calculated. If the new value agrees with the original assumed value, the assumption was the correct formation permeability. If the values do not agree, the process is repeated using the new permeability value in the calculation. Convergence is rapid, and a reliable permeability value results. Pressure fall-off data are used to check the result. Graphs of pressure and injection rate us functions of time given in the paper show that changes in permeability of the formation in the neighborhood of the wellbore are disclosed by this technique. Thus, the short-term test can he used to detect formation damage. Also, a rough measure of the radial extent of damage can be inferred, which is helpful in designing stimulation treatments. The mathematical model used for this work was a single-zone, horizontal reservoir with a damaged zone in which permeability decreased continuously as radial distance to the wellbore decreased. This model is more realistic than the usual two-zone, discontinuous permeability model used in published works; calculations indicate the realistic model is valid. Vertical variations in horizontal permeability were studied with this model, and results indicate that the permeability measured by the short-term test is the mean horizontal permeability for the vertical interval tested. The proposed short-term test thus should be useful in detecting and characterizing formation damage and in measuring formation permeability needed in calculating reservoir transmissibility. INTRODUCTION To plan the most efficient production or injection schedule for a well and to design or evaluate the optimal stimu- lation treatment, it is necessary to know the properties of the reservoir adjacent to the well, particularly the reservoir transmissibility and characteristics of a damaged zone, if one exists. Several techniques for determining reservoir transmissi-bility from well tests have been presented in the literature. 1,2,3,4 All these techniques rely on conducting constant-rate well tests that often are difficult to execute. A constant-pressure well test is generally easier to carry Out. and this paper contains the first available method for the analysis of constant-pressure well tests. Determination of wellbore damage from transient well tests has been the subject of several papers."" From these studies it is apparent that information necessary for determination of the characteristics of a damaged zone is available shortly after the transient well test is initiated. Consequently, it may not be necessary to carry out an extensive well test (for example, a pressure build-up test) if the primary purpose of the test is to detect the existence of wellbore damage. All previous studies of well testing to determine wellbore damage have been based on the two-zone perrneability model. In this model the damaged zone has a permeability k,, extending to a radius r,,, and the formation permeability k obtains from r, to the drainage radius r,.. Consequently, there is a discontinuity in permeability at r = r,,. This discontinuity can be eliminated by assuming a continuous variation in permeability through the damaged zone. The effect of this assumption on transient well tests is discussed in following sections of this paper. In addition, all formations have within them vertical permeability variations associated with lithology changes throughout the zone of interest. This paper also considers the effect of these variations on transient well tests. ANALYSIS OF CONSTANT-PRESSURE WELL TESTS The mathematical analysis associated with the injection of fluid at constant wellbore pressure into a single-zone, horizontal reservoir completely filled with a fluid of small and constant compressibility and constant viscosity is given in Appendix A. In this analysis it is assumed that the well is located at the center of an undamaged, circular drainage area. From this analysis, the formation permeability can be obtained as follows. 1, Estimate a value for the formation permeability k. 2. Prepare a plot of injection rate q vs

Jan 1, 1967

By Hollis L. Caswell

The present status of integrated circuits utilizing. superconductive switching. elements is reviewed with special attention given to fabrication techniques, methods for interconnecting completed circuits, and refrigeration requirements. Cryoelectronics has been largely an "inte- grated-circuit" technology since its conception because the switching speed of superconductive devices is attractive only when these devices are fabricated with thin-film techniques. It is true that cryotron circuits can be constructed from wires of appropriate materials (as indeed was done by Dudley Buck 1 in his early investigations) but these circuits will switch in times characteristic of milliseconds whereas similar circuits fabricated by thin-film methods have potential switching times of nanoseconds. Furthermore, cryo-electronic devices such as the cryotron lend themselves readily to fabrication by thin-film techniques since these components may be made from polycrys-talline thin films and are relatively insensitive to the presence of impurities (as measured by semiconductor standards). Therefore, during the past decade considerable effort has been devoted to developing techniques for batch fabricating circuit arrays containing superconductive switching elements. Technology had developed to the point several years ago that fabrication of cryoelectronic arrays containing up to one hundred devices was rather straightforward. However, larger arrays containing between lo4 and 106 components which are required for commercial development of cryoelectronics still pose very severe yield problems. Thus in a sense cryoelectronics found itself in 1962 at the point semiconductor technology finds itself today; namely, individual devices and small groups of integrated devices could be fabricated with acceptable yield and the outlook for building larger integrated-circuit arrays was bright. Unfortunately, problems associated largely with yield have made fabrication of these larger arrays difficult. Unlike semiconductor technology, cryoelectronics had to solve the problems of large-scale integration before it could become economically attractive. This has proven to be a sizable burden to bear. Since several reviews exist on superconductivity,2 superconductive devices,3 and cryoelectronic technology, no attempt will be made in this paper to summarize these areas. Instead a few specific topics will be dealt with in more detail. First, a brief description is given of selected superconducting switching and storage devices with special attention to several metallurgical techniques which improve the performance of these devices. Second, techniques used to fabricate cryoelectronic devices are described with emphasis on problems affecting yield. Third, techniques for interconnecting a number of cryoelectronic planes are described. And last, refrigeration of cryoelectronic components is discussed briefly since the low operating temperature of superconductive devices is an important consideration in this technology. SUPERCONDUCTING STORAGE AND SWITCHING DEVICES The basic superconductive switching device is the thin-film cryotron. The geometry of this device is attractively simple, since it involves only the intersection of two lines that are electrically insulated from each other. The switching element (gate) and control element (control) of a crossed-film cryotron are arranged as illustrated in Fig. 1. The material for the gate is selected to permit the gate to be switched from the superconducting to the normal (resistive) state by the application of a control current. Tin, which has a critical temperature (T,) of 3.7°K, is commonly used for the gate and the cryotron is operated at a temperature just below T, (for example, 3.5°K). The control material (normally lead, with T, = 7.2°K) is chosen so that the control is never driven normal during circuit operation. To improve cryotron operation, a ground plane, also of lead, is placed under all of the circuitry to act as a diamagnetic shield and improve the current-density uniformity across the width of various thin-film elements. Normally, line widths vary from 0.005 to ^ 0.020 in. and film thicknesses from 300 to 10,000A, although new fabrication techniques make narrower lines feasible. In fabricating cryotrons it is important that the edges of the gate elements be geometrically sharp to avoid undesirable switching characteristics associated with a thinner edge region, Fig. 2. One technique which has been used extensively to form patterns consists of placing a physical mask containing the film pattern between the evaporation source and the substrate and depositing through the mask. Film strips formed in this manner possess a penumbra at the film edges due to shadowing of the evapor-ant under the mask. Several techniques have been proposed for minimizing effects due to this penumbra. One of the more promising metallurgical techniques

Jan 1, 1967

NEW MEMBERS. The following list comprises the names of those persons who became members during the month of September, 1913: Members. ANDERSON, ANDREW P., Min. Engr 908 Story Bldg., Los Angeles, Cal. ANDROS, STEPHEN 0., Min. Engr University of Illinois, Urbana, Ill. BECKETT, PERCY G., Min. Engr Globe, Ariz. BLAIR, THOMAS S., JR., Prest. Blair Engrg. Co 343 S. Dearborn St., Chicago, Ill. BOYLE, HARRY, Min. Engr S07 Lowman Bldg., Seattle, Wash. BRADEN, EUGENE B., Vice-Prest., Selby Smelting & Lead Co., Merchants Exchange Bldg., San Francisco, Cal. CHALMERS, JOHN W., Min. and Elec. Engr., Morro Velho, Villa Nova de Lima, Honorio Becalho Minas Geraes, Brazil, So. America.

Jan 10, 1913

By D. Turnbull, J. H. Hollomon, J. C. Fisher

Application of the concepts of nu-cleation and growth to the analysis of experimental transformation data has led to valuable descriptions of phase transformations, an outstanding example being the transformation austenite —* pearlite which has been examined with particular care by Mehl and co-workers.&apos;-5 In addition to the pearlite transformation, the proeutectoid fer-rite and proeutectoid carbide transformations are known to proceed by nucleation and growth. Martensite, on the contrary, until recently was thought to form by a mechanism involving neither nucleation nor growth; however, extension of standard nucleation theory6 suggests that martensite, bain-ite, and the other products of austenite decomposition all grow from nuclei in the parent phase. The theory that martensite forms by nucleation and growth is strongly supported by recent experimental work of Kurdjumov and Maksimova.7 The concepts of nucleatioli and growth have been fruitful also in providing a sound basis for quantitative theoretical treatments of the kinetics of phase transformations. For example, Volmer and Weber8 and Becker and Döring9 developed the theory of nucleation from fundamental considerations to a point where excellent agreement was obtained with the results of experiments on the condensation of supercooled vapors. As a result of their analysis, the kinetics of vapor-liquid transformations now can be predicted. It seems probable that application of the theories of nucleation and growth to a quantitative study of austenite decomposition similarly will clarify the nature of the individual transfor: mations involved, and will enable the calculation of austenite transformation kinetics. In the present paper, the theories of nucleation and growth are applied to the austenite ? martensite transformation in steels. The analysis begins with a discussion of nucleation in single component systems. Martensite appears to be coherent with the parent austenite, hence the nucleation theory is modified to include the effects of elastic distortion. Nucleation in the two component iron-carbon system then is discussed, for most steels are primarily alloys of these two elements. Finally, M. temperatures and martensite transformation curves are calculated for each of several alloy steels of varying carbon and chromium content, and are compared with those determined experimentally by Lyman and Troiano10 and Harris and Cohen.11 Nucleation Theory NUCLEATION IN SINGLE COMPONENT SYSTEMS6,12-14 The work required for reversible formation of a region of phase within the parent a phase is expressed conveniently as the sum of two terms: W1 = Aa, the product of the area of the interface and the interfacial free energy, and W2 = VAf, the product of the volume of the region and the free energy increase per unit volume associated with the transformation. The total work is therefore W = Aa + VAf. When a is more stable than ß, Af is positive and W increases without limit as the volume increases. The transformation a ?ß does not occur. It is nevertheless true that small regions of phase ß enjoy temporary existence here and there in the a. The equilibrium number of ß regions of given size is proportional to exp(— W/kT) per unit volume of a, assuring that larger (ß regions occur with diminishing probability. When a is less stable than ß, Af is negative and W passes through a maximum as V increases. Assuming for simplicity that regions of ß are spherical, as is true when the interfacial tension is isotropic and there are no elastic strains, W = 4r2a + (4/3)*r3Af The maximum value of W is W* = 16iro3/3Af2 [1] for regions with radius r* = -2o/Af. [2] For single component condensed systems it has been shown14 that the steady rate of nucleation of 0 per unit volume of untransformed a is nearly proportional to exp[- (W* + Q)/kT] where Q is the activation energy for the unit processes of adding or removing one atom from an embryo or nucleus. If To is the temperature at which a and ß are in equilibrium, the rate of nucleation is a maximum at a temperature 0 < T < To where (W* + Q)/kT is a minimum. P regions smaller than critical size are called embryos; they tend to grow smaller and disappear, only exceptionally growing larger. Regions equal to or larger than critical size are called nuclei. A critical size nucleus may grow indefinitely large or may shrink back to a, either process decreasing the free energy of the region.

Jan 1, 1950

L. C. UREn,* BerkelEy, Cal. (written discussion).—I heartily concur with Rlr. .Fobs concerning the need for advanced courses on various phases of Petroleum Engineering. I think that his criticism is probably true of most of the engineering schools that are specializing at all in Petroleum Engineering, that is, that most of their so-called graduate courses are not of graduate caliber but are merely more specialized aspects of undergraduate subjects. It would undoubtedly be to the advantage of the petroleum profession if more advanced work could be offered in a few of the leading engineering institutions so that there would be something substantial to offer graduate students wishing to return after a period of undergraduate work, for additional training. There is no doubt but that a better trained engineer, more useful to the oil industry, could be secured from schools offering such advanced training. The problem of adpting our instruction to fit the needs of engineers trained along other lines who wish, after completion of their undergraduate work, to enter thc petroleum engineering field, is a more difficult one. It has been my experience that such men are usually sadly deficient along certain lines and that they are really not prepared for the more advanced work in Petroleum Production Engineering until they have gone back over the work which they have missed in their undergraduate training. I note that Mr. Fohs suggests that other eastern and western colleges not now stressing Petrolelim Engineering, should be encouraged to take up advanced work of this character. With this, however, I cannot agree unless the institutions arc also prepared to offer a full sequence of undergraduate work on which the more advanced courses may be superimposed. Whether or not there is a need for additional engi-ncering colleges entering the petroleum engineering field is an open qucstion. I believe that we arc turning out enough petroleum engineers at the present time and that none of the six institutions now specializing in this field arc overcrowded. Morc-ovcr, they are fairly well distributed over the country, though there may be room for an additional school in the field in the eastcrn section of the United States. F. W. Padgett, Norman, Okla. (written tliscussion).—Assuming that the stnclcnt has the proper fundamentals, that is, general science and a knowledge of the technology of the industry, then the problem is: What courses should be offered from the graduate standpoint? (a) Course Work.—His knowledge of the technology of the industry can be extended advantagcously by means of one and two-hour courses, which consist in a more detailed survey of the various branches of the industry. (b) Lilerdure.—This work may, or may not, be connected directly with his research problem. The student should become familiar with methods of locating articles in the 1iterature; should also become familiar with all the important original

Jan 1, 1928