Search Documents

By Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems are less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIXTM) and fixed film biological reactor, Denite°. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1994

By K. A. McDonald

This paper will describe the experiences of Hibernia Holdings, Inc. in constructing a mineral processing facility in Mexico. It will attempt to set forth a guideline on what companies attempting to operate in Mexico can expect and what actions they can take. Ownership laws, import/export laws, labor laws, security, transportation and operating experiences will be discussed.

Jan 1, 1994

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By T. J. Fenner

Research conducted in South African mines has demonstrated the benefit of ground penetrating radar for the detection of geologic features and hazards. This is crucial for safety and production considerations in underground mines that are as much as 4 kilometers deep. This paper describes a new ground penetrating radar system designed specifically for high quality data acquisition, in the harsh conditions of deep underground environments, for use by operators with minimal geophysical experience. Design criteria included automated functions, intrinsic safety, light weight and minimal power requirements. Data is processed on the ground surface by geoscientists using a PC.

Jan 1, 1994

By Bhattacharyya A. K

A strata parameter is introduced to include the deformation characteristics of the undermined strata in the prediction of subsidence movement. By using the strata parameter and mining factors as parameters, a nomogram for predicting the maximu

Jan 1, 1994

By P. V. Avotins, D. R. Nagaraj, S. S. Wang

Xanthates and dithiophosphates are the most commonly used collectors in the flotation of sulfide minerals. Other reagents such as thionocarbamates, mercaptobenzothiazoles (MBT), mercaptans and xanthogen formates occupy niche positions in industrial collector use. Over the last ten years there has been much activity by chemical companies to develop new collector compositions. The new collectors are aimed at meeting specific process needs such as recovering an increment of valuable metals, improved sulfide separations, increased flotation kinetics, and reducing reagents costs. A review of the patent literature shows that American Cyanamid (Cytec), Dow Chemical, Phillips Petroleum, Sentrachem Ltd., Henkel, Montan Chemicals and Elf Aquitaine, among others, have been active in sulfide collector research. Several companies have achieved considerable success in laboratory and plant tests of the new collectors; however, commercial acceptance for plant usage has been slow. Those most advanced have been plant tested extensively and some are in day-to-day use. The new collector types in this category are: Modified thionocarbamates, dithiophosphinates, organic sulfides, trithiocarbonates, monothiophosphates, and modified thioureas. Others such as substituted mercaptobenzothiazoles and monothiophosphinates have been tested in the laboratory. The chemistry of collectors developed in the last 10 years, their preparation, physical properties and their potential for commercial use are reviewed in this paper.

Jan 1, 1994

By William E. Hill

The blasting program at the Valdez Creek Placer Mine must deal with challenging situations throughout the year. During the short summer, extreme water conditions must be confronted, while the winter months present problems of a different nature, where the overburden freezes to a depth of up to 18 feet. These obstacles require techniques borrowed from hardrock blasting combined with creative experimentation to overcome.

Jan 1, 1994

The types of risk to mining projects using environmental protection as justification are examined. In Australia, Governments, whether Federal or State, enforce environmental legislation. The way they do This has an impact on the risk to a project. This is discussed and examples are taken from the Northern Territory uranium industry. Special reference is made to mine closures where the roles are not yet entrenched.

Jan 1, 1994

By Harold R. Kokal, Madhu G. Ranade

A metallurgical/flux is a substance that is added to combine with gangue (unwanted minerals) during ore smelting, with impurities in a molten metal, or with other additives in metal refining processes to form a slag that can be separated from the metal. Because slags are immiscible with the metallic melt and are of lower density, a separation of the slag and metal occurs if the viscosity and surface tension are of the proper values. The chemistries of slags are adjusted to provide the proper melting point, viscosity, surface tension, conductivity, specific heat, density, or chemical properties to effect the desired task. In addition to absorbing impurities from the metal, the purposes of the slag are to thermally insulate the metal bath, protect the molten metal from the atmosphere, and control the chemical potential of the system. Several excellent references on slags and metallurgical fluxes are available (Boynton, 1980, Lankford, Jr., et al., 1985, Turkdogan, 1983, Rosenqvist, 1974, Fine and Gaskell, 1984). The function of the slag might vary at different stages within a process prior to final melting. For example, the slag composition and behavior will change as materials descend in the iron blast furnace, or as they melt in the early stages of formation of steel- making slags. Selection of the chemistry for a slag might be influenced by factors outside the primary function as when blast furnace slags are used to make cement, rock wool insulation, or fertilizer supplements. Sometimes slags contain a sufficient amount of valuable recoverable elements to be sold as raw materials for other processes. Fluxes are often referred to as acid, basic, or neutral. Acid fluxes are those that generally form acids in water and bases are those that would generally form bases in water. Typical acid fluxes are silica, alumina, and phosphorus, although alumina can function as either an acid or base. Typical basic fluxes are lime and magnesia. Fluorspar, or calcium fluoride, is a neutral substance because it can be viewed as the reaction product of a base and an acid. The degree of acidity (ratio of acids to bases) or basicity (ratio of bases to acids) is often specified to characterize the slag chemistry for a particular system. The system might also be referred to as acid or basic depending on the choice of slag, for example, basic steelmaking uses slags with more bases (lime and magnesia) than acids (silica and alumina). Many forms of minerals and compounds have been used as fluxes depending on the process requirements, availability, costs, requirements for recycling of intermediate products, and environmental concerns. Because slags are most often mixtures of oxides and silicates, fluxes are usually oxides, carbonates (which decompose to oxides) and silicates. Slags comprising phosphates, borates, sulfides, carbides, or halides have also been used (Rosenqvist, 1974, Moore, 1981, Szekely et al., 1989). In ironmaking and steelmaking, some acidic components are sometimes added. In nonferrous processes slags and fluxes are acidic with silica as the primary component, and although the use of basic flux such as limestone or lime is not extensive, some amount is used to modify slag properties and some refining slags are lime based. The production of iron is accomplished by smelting of ores, pellets, and sinter in blast furnaces with subsequent refining of molten iron and scrap in oxygen-blown processes. The electric furnace is used to make steel, stainless steels, ferroalloys, and special alloys, whereas ferromanganese is often made in blast furnaces. Fluxes are used in all of these processes, and either limestone or lime is the major flux component with some dolomite, dolomitic lime, silica, alumina, and fluorspar being used. In ironmaking, the flux is added either by direct charging or through sinter and fluxed pellets. In steel refining by the basic oxygen process, flux is added as lime and dolomitic lime that are either charged as lumps or injected as fines. Some small amount of limestone is sometimes used. Fluorspar is often added as lumps or mixed with other fine materials in briquettes. Alumina is sometimes added to blast furnaces either by direct charging of sized lumps or through sinter. Typical acid fluxes are sand, gravel, quartz rock, used silica brick, or raw siliceous ore (Lankford, Jr., et al., 1985). Olivine, which is a magnesium-silicate mineral, has been added to iron blast furnaces to enhance removal of alkalis (Lankford, Jr., et al., 1985). Alumina in the form of bauxite, aluminiferous clay, and recycled alumina brick has been used as flux. Alumina can function amphoterically as either an acid or base, for example it can form aluminum silicate in high silica slags or calcium aluminate in lime-bearing slags (Lankford, Jr., et al., 1985). Limestone (calcium carbonate) and dolomite (magnesium-calcium carbonate), or fluxstones as they are sometimes called (Boynton, 1980), and their calcined forms, lime and dolomitic lime are the major basic fluxes. In the latter cases, the carbonates are de- composed in a kiln-type process to drive off carbon dioxide that might otherwise interfere with the subsequent smelting or refining process or require expensive forms of energy to effect the decomposition (e.g., by combustion of coke in the iron blast furnace). Limestone is considerably less expensive than lime because it is not calcined; however, lime is far more difficult to handle and reacts readily with water. Dolomite and dolomitic lime are used for their magnesia content. Fluorspar is a neutral flux often used as an additive in steel- making slags to improve fluidity, but it has also been used in combination with lime as a primary slag in electroslag refining (Duckworth and Hoyle, 1969). Fluorspar is available in several grades, with the lowest grade often used for steelmaking. When the price of fluorspar has risen, substitutes including aluminum smelting dross, borax, manganese ore, titania, iron oxides, silica sand, and

Jan 1, 1994

By T. N. Moore, E. M. De Souza

Because jackleg rock drills are a potential source of hand vibration exposure, they can effectively produce Hand Arm Vibration (HAV) Syndrome in their operators. This will affect operator efficiency and mine productivity. As a result, a significant amount of work has focused on redesigning rock drill handles using new materials to minimize hand-transmitted vibration. In previous work developed by the authors (1991), a detailed study was undertaken to determine the effectiveness of using elastomer covered handles in place of the standard steel design. The results indicated that, for an elastomer-based handle design, the overall acceleration level experienced by the hand can be reduced by as much as a factor of three, relative to the steel handle. It was also shown that this reduction takes place predominantly in the frequency range above 500 Hz. This paper presents an investigation of the long-term effectiveness of an elastomer-cushioned handle under different conditions underground. In this study, sponsored by the Mining Industry Research Organization of Canada (MIROC), a number of cushioned handles were quantitatively and qualitatively tested in five operating mines. The vibration testing program has indicated that the cushioned handle can reduce overall vibration levels by as much as a factor of three. The qualitative assessment program of the cushioned handles by the drill operators has indicated some degree of preference for the cushioned handles over the steel handles, if certain design modifications are performed. This research program indicated that cushioned handles have the potential to become the dominant method with regard to vibration reduction and operator performance.

Jan 1, 1994

Studies of Theological effects in grinding hold promise for improving this energy-intensive process. Six surveys of the Hellyer ball mill were conducted. The stream and sizing data from these surveys were balanced by JKMbal to compare the mill

Jan 1, 1994

By J. R. Koehler

The U.S. Bureau of Mines (USBM) ground control research program includes several projects focused on developing design criteria for yielding-pillar-based longwall gate road systems. As part of this program, mining practices at the Sunnyside Mines, Sunnyside Reclamation and Salvage Co., Sunnyside, UT, are being documented to preserve the long history of yield pillar system evolution on the property. Published information describing the specific in-mine performance of the numerous gate road configurations utilized at the Sunnyside Mines is very limited. To overcome this deficit, USBM personnel interviewed 30 longtime mine employees representing nearly 700 years of mining experience at the Sunnyside operations. Mining conditions in 12 specific areas in the Nos. 1, 2, and 3 Mines were discussed in the interviews. Also, broad topics such as general mining practices, safety, and geology were often addressed during the discussions. Comprising the body of this report is an extensive record of the events and conditions experienced while mining the identified areas. In addition, eight significant conclusions were developed that accurately summarize the general opinions of the interviewed personnel regarding mining conditions and practices at Sunnyside.

Jan 1, 1994

One of the biggest drawbacks of deciding upon a heap leach method of treating gold ore is the risk associated with the full-scale production heaps not performing as predicted by the testwork. This paper examines the key decisions that are taken in the design of a heap leach project, and suggests ways in which exposure to these risks can be minimised. It also looks at monitoring techniques to give early warning of problems and possible remedial actions.

Jan 1, 1994

By J. H. Ahn, J. E. Gebhardt, W. K. Tolley

Color measurements were made for pure minerals, mineral mixtures and flolation froths loaded with different minerals. The research objective eras to correlate color with the composition of mineral streams. An industrially available system consisting of a fiber-optic-based illuminator and detector was used to measure color. The color values of binary mineral mixtures varied according to the type and proportion of minerals in the mixture. The measured color values of mineralized froths in the laboratory and in a commercial flotation circuit were dependent on the amount and type of minerals present.

Jan 1, 1994

By K. J. Stanaway

Environmental pressures on waste disposal are forcing pigment producers to use higher content TiO2 feedstocks with lower levels of trace elements. Despite this, 50% of the worlds TiO2 comes from ilmenite concentrates with only 37 -54 % TiO2 An industry growth rate of 25 % in the next ten years combined with trends to diminishing resources and lower grades for rutile (95 % TiO2) and leucoxenized ilmenite (55 to 90% TiO2) mean that unless new discoveries are made soon, the industry will become even more reliant on ilmenite. A hypothetical ideal feedstock is presented and strategies to obtain it are suggested. Reasons for some of the mineral specifications are given.

Jan 1, 1994

Provide the technology to remotely reset circuit breakers on continuous mining machines used in extended cuts.

Jan 1, 1994

By Theodore M. Gurr, James J. Bartels

Phosphate produced fertilizers provide the phosphorous nutrients required by plant life to sustain significant growth, thus improving the production of food for the world's population. Phosphorous replenishment of soil currently can be obtained efficiently by no other means than by direct application of phosphate fertilizer to the soil. Phosphate products are also utilized in animal feeds, detergent, and various industrial processes. Thirty-three countries are presently mining phosphate rock for the production of fertilizers, and its process byproducts. The major phosphate rock producers are the United States, the former Soviet Union, Morocco, and China [(Table 1)]. Phosphate rock is generally defined as a rock material that contains phosphate minerals which are sufficient for commercial usage. Phosphate minerals are found in sedimentary igneous and metamorphic rocks. Economic resources of phosphates are primarily developed from sedimentary rock sources. The apatite mineral family comprises the majority of phosphate constituents from both sedimentary and igneous rocks. Igneous phosphate rocks are generally composed of fluroapatite whereas sedimentary rocks are generally composed of carbonate fluroapatite, or chlorapatite. Phosphate rock is mined by a multitude of processes, including surface and underground mining. The mined rock requires mechanical and chemical processing to liberate the phosphate for utilization as fertilizer. Approximately 85% of the world's phosphate production uses sulfuric acid, with the remaining processes utilizing nitric and phosphoric acids. Ammonia is also introduced in the manufacture of liquid fertilizer, ammonium phosphate and ammonium polyphosphate. GEOLOGY Mineralogy and Chemical Properties Phosphate most commonly is derived from the mineral apatite, which is chemically described as CA5(F,Cl,OH)(PO4)3. Apatite is also broken up into the composite apatite minerals which are fluroapatite Ca5F(PO4)3, chlorapatite Ca5Cl (PO4)3 and hydroxyl-apatite Ca5(OH)(PO4)3. Carbonate CO3 can substitute for PO, forming carbonate apatite, called francolite. The guano phosphate (bird excrement) mineralogy commonly occurs as brushite CaHP04.2H20, monetite CaHPO4, whitlockite Ca3(PO4), and dahlite Ca10(PO4)6(OH)2. Apatite minerals form from igneous sources where they are developed deep in the earth's crust; and the cooling processes are slow, producing long, hexagonal prismatic to tabular crystals. The termination of the crystal can be basal plans or pyramids. In some instances, the crystals are bipyramids. Faster cooling, or sedimentary derived apatites are more commonly cryptocrystalline. Collophane is a name given to cryptocrystalline apatite found in phosphate rock in fossil form. Apatite minerals are relatively soft and are used to describe the 5 hardness on the Mohs scale. Cleavage is poor and develops along the C(0001). The color of apatite minerals varies from colorless, to violet, and blue, but are predominantly green or brown; luster is vitreous to subresinous. Collophane's physical appearance is often opaline, dense, with colloform structure and sometimes concretionary, nodular or pulverulent. Phosphate Bearing Materials Origins Phosphate deposits of igneous and metamorphic origins have been well defined. Sedimentary origins have been defined, but with a greater degree of uncertainty. Research in the 1980s proved out some of these processes through studies of real time deposition in Chile, Peru, and Australia. Igneous intrusive alkali rock and associated contact metamorphic rocks, provide approximately 20% of the world's phosphate. Fluorine containing apatite minerals are the most common materials containing phosphorous. Fluorapatite occurs in most igneous rocks. Fluorapatite and fluorine hydroxylapatite, together with carbonate varieties of these, are important members of the group. Where an essentially pure chlorapatite, carbonate apatite, and hydroxylapatite are rare and restricted in occurrence, the fluorine containing types occur in most all igneous rocks as early formed accessory mineral, usually in microscopic crystals, and may occur as extremely large bodies as magmatic segregations from alkalic igneous rocks. Apatite is also found crystallized in pegmatitic faces of both acidic and basic types of igneous rocks. More specifically, apatite is associated with magnetite deposits, in hydrothermal veins, especially those formed at relatively high temperatures, and in veins of the Alpine type. Apatite is common in both regionally and contact metamorphosed rocks, especially in the crystalline limestones where it is associated with sphene, zircon, pyroxine amphibole, spinel vesuvianite, phlogopite, talc, chloride schists, and as a contact metamorphic mineral.

Jan 1, 1994

By James C. Duchon

The use of extended workdays (regular shift lengths of 10 or 12 h (hour), while still maintaining a 4O-h workweek) in mining operations is attracting growing interest in the United States. There is very little doubt that extended workdays is a very popular alternative among the work force because of the significant increase in days off, including weekends, especially when compared with traditional rotation schedules of working seven straight shifts or having only one weekend off every 4 to 6 weeks. However, there are some serious concerns by management, workers, unions, and various governmental policymakers that working 10-or 12-h days may create an added risk of accidents and health problems. The U.S. Bureau of Mines reviewed the literature studies related to the safety and performance issues of extended workdays. This report presents a summary of those findings. The studies examined in this review are divided into three sections: (1) laboratory, (2) field, and (3) accident and injury analysis. In general, results are inconclusive. Studies have shown both positive and negative effects. It is concluded, therefore, that in industries such as mining where accidents are a serious concern, special measures and evaluation in the use of extended workdays be considered.

Jan 1, 1994

By D. Malhotra

Metallurgists are continuously striving to improve recovery. But optimization of profits and/or revenue dictates that recovery can be sacrificed at the expense of throughput. However, recently there has been significant interest in the concept of retreatment of tailings to enhance recovery and hence revenue while maintaining high throughput. The authors discuss the technical and economic factors that need to be considered in evaluation of the feasibility of retreatment of tailings including the potential feed streams (i.e., rougher tailings, cleaner tailings, etc.) and processing options (i.e., physical beneficiation, chemical processing, etc.). A case study for base metals is discussed.

Jan 1, 1994

By J. A. M. Cano

Pot Grate tests were carried out in the pilot plant at Samarco producing pellets containing SiO2 between 2.0% and 2.2% in a wide range of basicity to be used in blast furnace. These pellets were submitted to tests in Samarco's laboratory and another laboratory in Germany to evaluate the metallurgical properties. The pellets in the binary basicity range (CaO/SiO2) from 0,87 to 0,95 were those that presented the best results in the Pot Grate tests. Based on the results, these pellets are being routinely produced?on industrial-scale confirming the results observed in laboratory tests.?

Jan 1, 1994