Search Documents

By C. W. A. Newey

I would like to make the following points in connection with the studies of the deformation of NiAl reported in the recent paper by Wasilewski, Butler, and Hanlon. 1) Much of their paper is concerned with demonstrating that slip occurs on either {110)(001) or {100)(001) systems. In their discussion they state "the existence of (001) as the basic slip direction can thus be considered established." This fact was established by the earlier studies of Ball and Smallman.32 Ball and Smallman also concluded that the slip plane was of the type (110) and they showed that cross slip or pencil glide on orthogonal (110) planes could produce macroscopic slip on planes of the (001) zones, e.g., (100). Wasilewski et al. refer to this paper by Ball and Smallman but not in connection with the slip system determinations. 2) Wasilewski et a!. eliminate the possibility of (111) slip in NiAl on dubious grounds. Their statement that ('the very high yield strengths of the (100) oriented crystals", in which (001) slip is constrained, "immediately ruled out the possibility of {110)(111) slip" cannot be accepted unequivocably; it would be reasonable if the crystals were completely brittle but they are not, as Wasilewski et al. and others33734 have shown. Their elimination of the possibility of (111) slip in a crystal compressed along [227] is misleading since there is no obvious reason why (111) slip should occur in a crystal of this orientation. In fact, from an analysis of the macroscopic surface markings on deformed (100) stoichiometric crystals, Pascoe and Newey34 have deduced that slip occurs on systems of the type {211)(111) and {321)(111). 3) Polycrystalline NiAl is known to undergo general deformati~n.Having emphasized that general deformation is impossible if only (100) slip occurs, it is a pity that Wasilewski et al. do not attempt to account for the disagreement between theory and their experimental results. Of course, (111) slip can provide the additional independent systems required for general deformation.

Jan 1, 1969

By A. J. Barry

This report presents observations made by Bureau engineers regarding hydraulic-powered roof supports that are currently being used or have been used on nearly all operating longwalls in the United States, A comparative summary of specifications for various types of powered supports with a brief description of the mine conditions has been compiled to enable mining engineers and mine operators to readily evaluate the differences in design data. Some of the support data furnished in the field may vary from those listed in manufacturers' brochures because of the trend to customize various support components to meet specific mine conditions. A method of estimating support requirements for different assumed operating conditions is presented. Similar computations for specific mine conditions may be used to make preliminary estimates of support requirements.

Jan 1, 1969

The non-metallic minerals, excluding the construc- tions and fuel materials have for long been the "poor relations" of the Mining Industry of New South Wales. The State is self-sufficient in only a few of the industrial minerals and is almost completely lacking in any of the essential fertilizers. The deficiencies must be met by imports from overseas and interstate and in fact New South Wales imports some quantity of every one of the non-metallics. For the year 1967 the value of non-metallic mineral production amounted to only $9,390,000 or less than 3.5% of the States total of $275,900,000 for all classes of mining and quarrying. In roughly the same period, the 1967-68 financial year, New South Wales imported non- metallic materials, valued at well in excess of $22,000,000 from overseas and over $2,000,000 from interstate sources.

Jan 1, 1969

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

By D. Mills, G. B. Craig

The defortnaliotz of zirconicltt single crystals conlaining osygen in the range 740 to 6800 atom parts per nilllion was esanined oc7er the range 77" to 950°K. An anctlsis of the dqfarmaliotz parameters leads to the cotcllsiotr that the rale -cotzfrolling thermally activated dqivr,irrtion process oe-r /he range 77" to 560°K is oc.crco,ling osvgen alotns. A thermally actitaled defor,ilntion process is not found between 600" and 800", but does occur aboz%e 800°K. THE present investigation was undertaken to measure the effects of controlled amounts of oxygen on the deformation parameters of a zirconium single crystals over the temperature range 77" to 950°K and to determine the rate-controlling mechanisms. Although there is no doubt that the mechanical properties of the group IV metals, titanium, zirconium, and hafnium, are strongly influenced by the interstitial impurities oxygen, nitrogen, carbon, and hydrogen, there are many conflicting theories as to the role played by the interstitials during the deformation proess.'- There is general agreement that the mechanisms which control plastic flow in a metal impose characteristic values on such parameters as the flow stress and its temperature dependence, the activation volume, and the activation energies. These parameters will be used to analyze the deformation mechanisms. eltham,' Sargent,16 and ibbs' have shown that the stress relaxation technique allows the activation volume characteristic of the deformation process to be found during the course of a simple tension test. In many cases it is found that the relaxation of stress is logarithmic with time and obeys a relationship of the following form: T-T = AT =S logl0(qt + C) [I] where t, is the shear stress at the start of the relaxation test, t is the shear stress at time t, and S. q, and C are experimental constants, and S is the strain rate sensitivity of the stress t as shown in the appendix. The slope found from a semilogarithmic plot of At vs time is approximately equal to S. The activation volume u, association with the deformation process, is found from the following relationship: The theoretical treatment of thermally activated plastic flow due to schoeck18 shows that the activation volume when combined with the temperature dependence of the flow stress gives the activation energy for the process according to equations: seegerZ3 considers that the flow stress at lower temperatures ld is composed of two parts such that Tapplied = tinternal + Teffective , where Teffective 3 ff , is the stress necessary to overcome the local obstacles to deformation and Tinternal, ri, is the stress necessary to overcome the long-range elastic stress field of dislocations on other planes. ri is considered to be largely elastic in origin and can be estimated from the stress value at the temperature independent portion of the flow stress-temperature curve. EXPERIMENTAL The crystal bar zirconium used in this investigation was supplied by Wah Chang Corp. whose certified analysis gave the following impurity contents in parts per million by weight: oxygen, 150; nitrogen, 10; iron, 180. All others were less than 100 ppm. The oxygen and iron contents were confirmed by neutron activation and chemical analyses, respectively. Single crystals were grown in an electron beam furnace according to the method of Wilson and Pickle-simer'' and ills.'' The orientation of the crystals was such that the specimen axes were located in the lower third of the standard section of the basal plane stereographic projection for zirconium. This orienta-

Jan 1, 1969

By H. F. Feldmann

This Bureau of Mines report presents a method for the computer solution of the equilibrium compositions of any complex, multiphase, chemical system for which appropriate thermodynamic data are available. The method describes in detail the computation of systems in which solid or liquid species can form by heterogeneous chemical reactions where these species do not occur in any equilibrium equations. Also described are the calculation of phases formed by condensation (pure or solutions) and the inclusion of other system restrictions such as electroneutrality. The method is being used to compute the equilibrium composition of mixtures of an electrically conductive plasma and a liquid slag phase arising from the high-temperature combustion of coal for magnetohydrodynamic power generation. These mixtures can contain up to 65 species including gases, liquids, free electrons, and ions.

Jan 1, 1969

By K. H. Adams, T. Vreeland

The basal stress-strain behavior, dislocation density, and strain vale sensitivity of the flow stress uqere measured at room temperature on single crystals oj-zone-refined zinc , 99.999 pct Zn, and zinc containing 0.0025 and 0.02 wt pct Al. No significant change in the stvain rate sensitivity of the flow stress occurs with the addition of aluminum. Changes in dislocation substructure and nonbasal dislocation density were obserrled with the addition of aluminum. The effect of aluminum on the basal slress-strain behavior is explained in terms of changes in nonbasal dislocation density which determines the separation distance of junctions between basal and nonbasal dislocations. The onset of basal slip is associated with the breaking of attractive junctions. The chunge in basal dislocation density was found to be proportional to the one-third power of the plastic shear strain, indepedent of purity. THE effect of impurities in solid solution on the stress-strain behavior of single crystals has been the subject of many theoretical studies. These studies have generally concentrated on the interactions between impurities and dislocations to explain the hardening effeet of impurity additions. The theories that have been proposed include those of yott and Nabarro,&apos;l&apos; Cott-re11; Suzuki; and Fisher. In practice, it is generally difficult to predict the relative importance of the vari- ous effects due to impurities. In addition, secondary effects of impurity additions such as induced changes in dislocation density and substructure in the as-grown crystals have received little attention. Many experimental investigations have been conducted on the effect of impurities on the stress-strain behavior of fcc crystals. Hcp crystals have not received much attention except for the extensive work of Levine et a1.= on magnesium alloy crystals. Stuwe~&apos;&apos; has studied the effect of copper impurity on the critical shear stress of zinc crystals and has interpreted the results in terms of the impurity atmosphere model of Cottrell and Jaswon. This report presents the results of an experimental study of the effect of aluminum additions to zinc on the basal stress-strain curve and the strain rate sensitivity of the flow stress. Etch pit techniques were used to measure and characterize the dislocation density and substructure in the zinc alloy crystals. EXPERIMENTAL PROCEDURE Specimen Preparation. Compression test specimens of four different purities of zinc were prepared from CP grade zinc of 99.999 pct purity obtained from the New Jersey Zinc Co. An analysis of this material furnished by the supplier indicated the following impurities in wt ~ct: Pb = 0.0002; Fe = 0.0002; Cd = 0.00005; other <0.60011. A quantity of material of this grade was further purified by zone refining. Zone refining was carried out under a helium atmosphere by passing a double &apos;One furnace Over a 6-ft-10ng charge at the rate of 2 in. Per hr. * total of ten double zone passes were made before the charge was removed from the furnace. The first one third of each charge was used to grow single crystals. Quantities of two

Jan 1, 1969

By Tuncel M. Yegulalp, Malcolm T. Wane

In general, many problems relating to the exploitation of mineral deposits are probabilistic in nature. This derives from the fact that the geologic universe is inherently random. Probability theory and statistics have been found useful for forecasting the behavior of natural events that occur in the geologic universe. The objective of this paper is to illustrate the application of the theory of extremes to this fore-casting problem. For example, it is customary for design purposes to determine the rupture strength of geologic materials. The theory of extremes is exceedingly useful in describing that portion of the frequency distribution of rupture strength which contains the least strengths. Parameters describing the distribution of the least strengths are more important to the designer of mining excavations than parameters describing the total distribution. The basic principles of the theory of extremes will be detailed and illustrated. Any person required to work in the laboratory of nature is aware that uncertainty is a salient feature of all mining enterprises. A mining engineer required to plan the most efficient, practicable, profitable, and safe mine finds himself face to face with numerous ill-understood and often unquantifiable states of nature. Basic information necessary for adequate planning is often lacking or derived from incomplete tests on samples or experience of doubtful validity. The planning procedure usually takes the form of determining a feasible layout with the intent of determining an optimal layout when and if the necessary details and information become available. The crux of the entire procedure is the choosing of numbers to put into the operational and structural models which encompass the plan. Many times these numbers must be assigned qualitatively from past experiences and are called the "most probable ones." At other times, load records, performance records and material tests provide a basis for extrapolation. In any event, the numbers are chosen from a distribution or set of all numbers. Since each number in the distribution represents a possible state, the choice of any particular value is based upon a decision rule. To illustrate, consider the design of an underground structure or the design of a rock slope. The initial step is the formulation of the various possible structural actions which result from the geometry of the layout. For a given structural model various intensities of behavior are possible depending upon the load, deformation, and material characteristic spec-trums, respectively. Of particular interest to mining people is the failure behavior or condition, i.e., when there is a complete collapse of structural resistance by either structural instability or fracture. A necessary feature of the analysis is the "rupture strength" of the material. Information on the rupture strength is derived from testing either in situ or in the laboratory and the usual outcome is a variation in the test results. The methodology used to overcome this variation is to construct a frequency distribution of rupture strengths, and then determine a measure of central tendency and variability. The main idea involved is that the central tendency number will be used in the failure calculations and the measure of dispersion will be used to estimate the probability of failure. In particular if the distribution of rupture strength is normal, the mean rupture strength is the central tendency number and the standard deviation of the rupture strength is the measure of variability. Suppose the mean value of rupture strength is 1000 psi and the standard deviation is 200 psi. Insertion of 1000 psi into the failure calculation produces results that are unsafe, hence a common decision rule is to reduce the mean value by a "factor of ignorance" so that the failure calculation will produce a "safe result." If two is chosen as a factor of ignorance, this means the value inserted in the calculation is 500 psi or 2.5 times the standard deviation. The next step is to determine the percentage chance that failure will occur from a design created on this basis. Tables on the normal distribution function show that this percentage chance is 0.621% or approximately 7 times out of 1000. In practice, however, the situation is more complicated than represented by the foregoing illustration. The laboratory or field testing program usually constitutes a pathetically small sample of the geologic universe of interest and not enough testing is carried out to determine the exact form of the distribution of the test results. The normal, Cauchy and Student&apos;s T distributions are strikingly similar, and it becomes a matter of mathematical convenience to assume the normal law for phenomena which follow other laws.

Jan 1, 1969

By John W. Cahn

The spinodal has long been regarded as a limit beyond which a homogeneous phase could no longer be metastable. But only recently has it become apparent that a phase beyond the spinodal would decompose by simple diffusional clustering mechanism quite different from the nucleation and growth mechanisms encountered for metastable phases. The theory of spinodal decomposition, which is based on the diffusion equation modified by thermodynamic requirements , is phenomenological, and each parameter can be measured by independent thermodynamic or diffusion experiments. The details of the theory have been carefully verified in a number of simple systems. It appears that the spinodal mechanism is commonly encountered in clustering reactions in solids and glasses. HISTORICAL INTRODUCTION The understanding of the earliest stages of precipitation in alloys has been the subject of three prior Institute of Metals Lectures. In 1932 Paul ~erica&apos; reviewed the puzzling evidence that hardening of duralumin is completed before precipitation of CuAlz takes place and suggested that hardening occurs when the copper atoms "assemble in random groups on lattice positions of the duralumin, not of the CuAlz lattice". He called these random groups knots. This modification of his dispersion hardening theory seemed to fit all the facts, but Merica worried that the required diffusion "is just the reverse of what we deem normal; although quite spontaneous, it proceeds uphill, if you please". The reality of Merica&apos;s knots was quickly confirmed by Guinier&apos;s&apos; and preston&apos;s3 X-ray work and these knots are today known as G.P. zones in their honor. Theoretical justification for uphill diffusion was also quickly provided by Becker and Dehlinger~ who noted that the diffusion coefficient could be negative in certain regions of phase diagrams. The boundaries of such regions could be described by a 90-year-old thermodynamic concept first described by ~ibbs&apos; in 1877 as a limit of metastability for fluid phases, which by 1890 had received the name spinodal (see Appendix A). Spinodal in fluids is as old as nucleation theory. Both appear for the first time in the same paper by Gibbs who called the spinodal the limit of metastability. For the first 50 years, nucleation theory was forgotten and the spinodal was extensively treated in every good thermodynamics textbook.81Q The idea was simple and logical and it was accepted as part of a rigorous thermodynamic development of metastable phases, and for a while it was extensively investigated theoretically.

Jan 1, 1969

By P. Bolsaitis, L. Skolnick

A model of metallic solutions is postulated which explains the energy of formation of alloys on the basis of changes in electron density around solute and solvent atoms and changes in pairwise interactions between atoms. The model is based on the Wigner-Seitz cell model of metals, with the electronegativities of the metals as the parameter for the electron-attracting power of the constituent atoms. In contrast to models based on the description of cohesive energy in terms of pairwise interactions only, which require an empirical, adjustable correction parameter to the Berthe-lot relations in order to predict negative energies of formation, the electron cell model accounts for both negative and positive energies on the basis of parameters of the pure components. Calculated heats of mixing based on published parameters of the pure metals are found to compare favorably to experimental values, despite the absence of any adjustable parameters in the model. THE formulation of an "exact" quantum mechanical model for the energy of cohesion of metals reduces ultimately to the many-body problem and for a complete solution would require the knowledge of wave functions and energy levels of all the particles in the system. The case of alloys is further complicated by the fact that the potential fields around the constituent atoms are different and the matching of boundary conditions in terms of the resulting wave functions is still an unresolved mathematical problem. It appears that in spite of the numerous investigations that have led to an elucidation of many properties of the metallic state, the formulation of the Hume-Rothery rules in 1931 marks the lone accomplishment toward simple, qualitative prediction of the energy of formation of alloys. More recently Friedel&apos;&apos; and Arafa have utilized the modern concepts of the electronic structure in metals in combination with the Hume-Rothery rules to arrive at quantitative estimates of the energy of formation of alloys with low solute contents. The relative success of the Hume-Rothery rules and Friedel&apos;s and Arafa&apos;s studies encouraged broaching the subject of formulation of a model based on realistic physical parameters and of conceptual and mathematical simplicity that could be applied to alloys regardless of concentration. On the basis of the free-electron theory, the cohesive energy of pure metals can be expressed as a function of "valence" (number of free electrons per atom), lattice parameter (or density), and the ioniza-tion energy. In addition to the electronic contributions to cohesion, one has to consider the pairwise exchange interaction energy between neighboring ion cores and the contribution from van der Waals forces. The energy changes upon alloying are viewed as resulting primarily from a redistribution of electron densities around the ions (a simplification of the more basic concept of a change of the wave functions of the electrons in the presence of a perturbing potential field). In addition there is a change in the pairwise interactions between neighboring ions which is usually the only factor taken into account in commonly used adaptations of the quasichemical theory. The electronegativities of the metals forming the alloy are used as the measure of the electron-attracting power of the ions in the alloy and the difference in electronegativities as the driving force for changes in electron energy on alloying. The interplay of pairwise interactions and electronic forces results in positive or negative energies of formation of alloys. Results obtained for systems to which the free electron model is best applicable are in good agreement with experimental values. 1) COHESIVE ENERGY OF METALS IN TERMS OF THE ELECTRON CELL MODEL The simplest physical model of a metal is that of a lattice of positive charges immersed in a sea of uniform, negative charge distribution represented by the

Jan 1, 1969

A method for the detection and analysis of tin in cassiterite ores is discussed. An empirical relationship was established between the tin content of an ore sample and the percentage absorption that this sample produced in a Mossbauer experiment. The time taken to complete an assay with this method is much less than with any of the methods currently in use. The equipment can be adapted readily for use in the field.

Jan 1, 1969

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By J. M. Eldridge, P. Balk

Phosphosilicate glass films were formed, by reacting gaseous P2O5 with SiO2, over a large range of temperature (800° to 1200°C) and gas phase composition (nearly two orders of magnitude of effective P2Ospressure). The film compositions generally corresponded with the liquidus curve, delineating the maximum solubility of the tridymite Phase of SiO 2 in phosphosilicate liquid solution at the temperature of film formation. It is shown that the P2O5 concentration of the phosphosilicate liquid film tends to decrease by reaction with the underlying SiO 2 layer until the liquidus curve is reached. The validity of the thermodynamic argument used in this explanation is supported by the results of a determination of the composition of borosili-cute films, prepared by reacting gaseous B2O3 with SiO2 at different temperatures. The kinetics of phosphosilicate film formation were described by a model predicated on a steady-state diffusion of P2O5 through the film. UNDERSTANDING of the processes leading to formation of phosphosilicate and borosilicate glasses is of great importance for producing passivating layers on FET devices. Passivating films with optimum characteristics are preferably formed in a separate step, independent of the doping of the semiconductor.&apos; The results of an investigation carried out to gain improved insight into the mechanism of glass formation are presented in this paper. It would be expected that application of the known Pz05-Si02 and B 2 O 3-SiO2 phase diagrams should be useful in extending understanding of the glass-forming processes. However, the question of the propriety of treating thermally grown SiO2 in these binary oxide systems by the methods of equilibrium thermodynamics must be considered when this application is attempted. Although Sah et a1.&apos; and Allen et al. 3 investigated the kinetics of formation of phosphosilicate glass (PSG), they failed to adequately relate their diffusion models to the occurrence of experimentally observed phases in the PSG/SiO 2/Si system. Horuichi and yamaguchi4 investigated the diffusion of boron through an oxide layer and described their results in terms of a model similar to that of Sah and coworkers. More recently, Kooi 5 and Snow and Deal6 reported the compositions of PSG films formed by depositing P2 O 5 onto SiO2. These compositions apparently coincide with those at the liquidus curve delineating the maximum solubility of crystalline SiO2 in phosphosilicate liquid solutions. These authors did not discuss the thermodynamic implications of their results on the structure of thermally grown SiO2 films. The structure of thermally grown Sio2 films and that of vitreous silica are generally thought to be quite similar. Since the solubility of a substance depends on its structure, it is relevant that the solubility of vitreous silica in water7 is highly reproducible, like the solubility of thermally grown SiOz in phosphosilicate liquid. Furthermore, the vitreous silica-water system appears to be in true thermodynamic equilibrium (viz., the same solubility value can be approached from both supersaturated and under-saturated solutions). Sosman7 suggested that a type of two-dimensional lattice may form at the silica/solution interface, resulting in the observed solubility behavior that is characteristic of a crystalline solid. An alternative explanation may be that vitreous silica has a microcrystalline grain structure. Other investigators have suggested that vitreous silica has essentially the structure of B cristobalite,&apos; or is composed of microcrystals of p tridymite or cristobalite, or a mixture of both. Presumably the grain size would be sufficiently large to minimize any appreciable contribution of the grain boundaries to the solubility of the crystalline matrix. The present investigation was carried out to clarify the significance of the boundaries in the Pa,-SiO, and B2O3-SiO2 Systems in determining PSG and BSG (borosilicate) film compositions. Furthermore, the kinetic data for PSG film formation were extended, using a wider range of formation parameters than were previously reported. One model describing the kinetics of film formation will be presented that is compatible with the thermodynamics of the Pa5-Si02 system. EXPERIMENTAL PROCEDURE Glass Film Preparation. SiO2 films (1000 to 8000A thick) were obtained by oxidation of silicon substrates in dry O2 at 1100°C. PSG and BSG films were prepared by exposing these layers to gaseous oxides obtained by reacting high-purity POC13 and BBr3, respectively, with O2. A double-columned saturator was used to ensure complete saturation of the N 2 carrier

Jan 1, 1969

By G. R. Speich

The interlarnmelm spacing, growth rate, and degree of segregation that accompany cellular precipitation in four Fe-Zn alloys containing 9.7, 15.2, 23.5, and 30.5 at. pct Zn have been determined in the temperature range 400" to 600°C. The chemical free-energy change for the reaction was calculated from the available thermodynamic data and the known compositions of the phases. The fraction of the chemical free-energy change for equilibrium segregation that is converted into interfacial free energy decreases from 0.43 to 0.08 as the magnitude of this free-energy change increases from 35 to 270 cal per mole. At constant temperature the cellular growth rate is proportional to the cube of the dissipated free energy. At 600°C newly 100 pct of the equilibrium segregation is achieved during cellulm precipitation whereas at 400°C only 85 pct of the equilibrium segregation is attained. During cellular growth, mass transport of zinc occurs by grain boundary diffusion; excess zinc remaining in the a! phase after the completion of growth is removed slowly by volume diffusion. A modified Cahn theory of cellular precipitation predicts the observed interlamellar spacing within a factor of two. In cellular precipitation reactions such as pearlite formation or discontinuous precipitation, the basic problem is to predict the variation of growth rate G, interlamellar spacing S, and degree of segregation P with composition and temperature. To accomplish this we need three independent equations relating these quantities. One of these equations comes from the diffusion solution. To obtain two additional independent equations, some assumptions must be made. cahnl has suggested recently that two plausible assumptions are 1) that growth rate is proportional to the dissipated free energy and 2) that the spacing which occurs is that which maximizes the dissipated free energy. According to the first assumption, this spacing also maximizes the growth rate and the rate of decrease of free energy per unit area of cell boundary. The present work was undertaken to test these assumptions. To test the first assumption it is necessary to study a cellular reaction over a wide range of supersatura-tions to establish a relationship between G and the dissipated free energy at constant temperature. This is possible only in discontinuous precipitation reactions since in pearlite reactions constituents other than pearlite form if the composition of the parent phase deviates even slightly from the eutectoid composition. The Fe-Zn system was chosen for study because 1) discontinuous precipitation proceeds to completion over a wide temperature and concentration range, 2) the degree of segregation within the cell can be measured by lattice parameter measurements,2 and 3) the thermodynamics of this system have recently been determined by Wriedt.3 In this system the cells consisting d alternate lamellae of a and r phases form from supercooled iron-rich a phase. The a phase within the cells is bcc as is the original a phase, cia, but has a different orientation and a slightly lower zinc content than the original a phase. The r phase has a zinc content of about 70 at. pct and a crystal structure isomor-phous with T brass. EXPERIMENTAL PROCEDURE Four Fe-Zn alloys with 9.7, 15.2, 23.5, and 30.5 at. pct Zn were prepared from carbonyl-iron powder (400 mesh, 99.8 wt pct Fe) and zinc powder (200 mesh, 99.99 wt pct Zn). The powders were ball-milled together and cold-pressed under 60,000 psi to discs $ in. thick by $ in. diam. The cold-pressed discs of the alloys with 9.7 and 15.2 at. pct Zn were sealed in evacuated silica capsules and heated slowly to 1100°C over a period of 1 week (3 days at 600°C, then 3 days at 80O°C, then 1 day at 1100°C). The alloys with 23.5 and 30.5 at. pct Zn were treated similarly except that the final homogenization temperatures were 1000" and 85O°C, respectively, to prevent melting. The alloys were quenched in iced brine from the final homogenization temperature. Specimens of each alloy were subsequently aged in salt pots at temperatures of 400°, 450°, 500°, 550°, 600°, and 650°C for times that varied from a few minutes to several hundred hours. At a late stage of this work, an alloy containing 11.2 at. pct Zn was prepared by vapor-impregnation of iron foil with zinc vapor at 890°C. This alloy proved useful for electron microscope studies because it was free of porosity. The homogenization and aging conditions were based on the recent Fe-Zn phase diagram of Stadelmaier and Bridgers4 rather than the earlier diagram of ansen.5 They consist of a homogenization heat treatment in the homogeneous a field followed by an aging treatment in the two-phase a + r field. The aged specimens were metallographically polished and etched in 2 pct nital and the radius of the largest cell in the microstructure determined. This radius plotted vs time gave a straight line whose slope is the boundary migration rate or growth rate G of the cell. To determine the interlamellar spacing, specimens were examined by surface-replica and thin-section electron microscope techniques. Because of the irregular nature of the lamellae within the cell, the average interlamellar spacing S .of the cell was measured by the method of Cahn and Hagel,6 where S is defined by:

Jan 1, 1969

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By J. W. Martin, L. K. Singhal

Grain boundary M23CB precipitates have been shown to form by a process involving the migration of an austenite grain boundary, and each plate of precipitate is in parallel orientation with one of the austenite grains constituting the boundary. The carbide distribution and morphology appear to be sensitive to grain boundary mis orientation. Some areas of austenite grain bowzdary permit the development of an array of M,C, particles, some of which are in parallel orientation with one grain and some with the other grain constituting the boundary. Massive carbide at grain boundary triple points is also shown to be in parallel orientation with one constituent grain. PREFERENTIAL precipitation during aging of carbides of the type (Fe,Cr)23C6, usually written MZ3C6, in grain boundaries of quenched austenitic stainless steels has been widely recognized. M23C6 has a complex cubic crystal structure&apos; which contains ninety-two metal atoms and twenty-four carbon atoms per unit cell. Less energy is involved in forming grain boundary precipitates than in the formation of intragranular precipitates, and the process is further enhanced by the accelerated diffusion rates in the boundaries and by the probability of segregation of chromium atoms and carbon atoms to the region of the grain boundaries during prior solution heat treatment in order to reduce lattice strain. Early electron micrographic studies2, 3 involving either extraction replica or normal replica techniques established the geometric or dendritic form of the carbide particles, although this approach led to dis- pute as to whether the particles grew within the plane of the boundary or grew into the matrix.4-6 More recent thin-foil studies&apos; have claimed to identify a discontinuous precipitation process involving M23C6 at grain boundaries, and the object of the present work was to attempt to clarify the situation using modern electron micrographic and diffraction techniques. 1) EXPERIMENTAL 1.1) Material. The steel selected for this work had a base composition of 24 pct Ni-25 pct Cr-3 pct Ti and contained about 0.04 pct C. The full analysis if given in Table I. This alloy was in the form of strip which had been hot- and cold-rolled to a thickness of 0.6 mm. 1.2) Heat Treatment. Specimens 4 cm long by 1 cm wide were solution-heat-treated for 3 hr in argon at 1150°C, followed by water-quenching. Specimens were subsequently aged in vacuo at 750°C for periods up to 500 hr. 1.3) Preparation of Electron Microscope Specimens. The heat-treated strips were cut bv spark machining into discs of 3 mm diam and 0.6 mm thickness. he-discs were dished on both sides using an electrolytic jet of 15 pct HCl electrolyte at 80 v. Final electro-polishing of the discs was carried out using 10 pct perchloric acid, 20 pct glycerol, and 70 pct ethanol at 10 v. The current density was kept below 300 ma. cm"2 by cooling the electrolyte to 0" to 5°C. As soon as a small hole appeared, the electropolishing was stopped and the specimen was quickly washed with ethanol.

Jan 1, 1969

By I. R. Taylor

Vanadium has recently joined the growing list of mineral commodities being exploited by surface mining methods. Union Carbide Corp. controls several vanadium deposits in central Arkansas near the city of Hot Springs in Garland County and the community of Magnet in Hot Spring County (Fig. 1). Two open pit mines, located approximately five miles southeast of the city of Hot Springs in the Wilson Springs area, have been developed for production during the past two years. Adjacent to the mining area the company has recently completed a 1,600-ton-per-day (tpd) processing plant to treat the Wilson Springs and Magnet Cove ores (Fig. 2). Although this operation constitutes the largest vanadium mining project in the United States, the open pit mines are of moderate size. A number of small to medium-sized surface mines will be developed during the life of the operation. This chapter describes the methods and practices used to bring these recently discovered vanadium deposits into production. PRELIMINARY EXPLORATION The vanadium potential of the deposits near Hot Springs and Magnet Cove was first investigated by Union Carbide Corp. in 1960. These areas have long been of interest for their varied mineral content and were previously explored by government agencies and private interests for titanium, columbium, molybdenum, and uranium. No sustained operations resulted from this early work, although the rutile deposits of Magnet Cove were worked intermittently between 1911 and 1944.l Significant vanadium concentrations were reported in a U.S. Bureau of Mines publication describing the investigation of a titanium prospect

Jan 1, 1969

Jan 1, 1969

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.&apos; The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By J. D. Wood, J. T. Smith

ALLOYS with a dispersed second phase in a metallic matrix are generally much stronger than the matrix itself. Plastic deformation in dispersion-strengthened alloys is usually confined to the matrix phase when recovery processes are active, while in the absence of recovery both phases may yield.&apos; The alloy system studied in the present research was WC-12 wt pct Co and consisted of noncoherent WC particles dispersed in the cobalt matrix. Some particle-to-particle contact existed but not enough to produce a continuous WC skeleton. The microstruc-ture of the WC particles was characterized by very straight edges, forming a trapezoidal shape in any plane of polish. Previous investigations with WC-Co alloys at room temperature have shown that fracture of the WC particles occurs in transverse rupture testing.&apos; Room-temperature slip was reported for WC particles after indentation for hardness measurements.3 Elevated-temperature deformation of WC particles in a WC-12 pct Co alloy was suggested by recent electron microscope studies of specimens deformed at 900&apos; to 1000°C.4 In highly deformed alloys, the WC edges were serrated in contrast to the usual straight or smooth appearance. WC-12 pct Co and WC-15 pct Co alloys have been previously studied under elevated-temperature com-pressive-creep conditions by the present authors. Electron microscope studies of two-stage replicas from deformed specimens showed no evidence of slip or fracture of the WC particles. These specimens were brought to temperature and allowed to equilibrate prior to the application of the creep load. It was believed that the load-application rate, a crosshead speed of 0.005 in. per min on an Instron universal testing machine, was sufficiently low that recovery within the cobalt matrix was sufficient to limit the deformation to this matrix. A series of experiments was performed to evaluate the influence of loading rate on the deformation of WC-Co alloys. A WC-12 pct Co alloy was selected for these determinations. The average WC particle size was 4.45 p with an average linear separation between particles of 0.59 p. The selected temperature was 800°C and was monitored with a Chromel-Alumel thermocouple attached to the specimen. Testing was conducted in an argon-atmosphere chamber to prevent oxidation of the WC-Co specimens. This chamber was mounted on an Instron universal testing machine equipped to apply the load at a fixed rate. Each specimen was loaded to 110,000 psi compression stress at 0.05 and 0.5 in. per min. The loading rate was monitored prior to insertion of the test chamber and was found to be almost precisely the nominal rate selected. The specimens were raised to temperature and held to equilibrate with the surroundings, and then the load was applied and held for 4 hr to duplicate the exposure time utilized for the creep specimens. The time to reach full load at a crosshead speed of 0.005 in. per min was some 500 sec and was reduced to 50 and 5 sec as the loading rate was increased to 0.05 and 0.5 in, per min, respectively. The model developed by Ansell,&apos; when recovery processes do not occur, considers that fracture or deformation of the dispersed particles is necessary to relieve back stresses on dislocation sources and allow dislocations piled up against particles to sweep out in the matrix to cause plastic deformation; he further states that, even at elevated temperatures, the dispersed-particle deformation is necessary for yielding in the absence of recovery. For the case of straight dislocation segments piled up against a straight barrier, such as the straight-sided WC particles, the shear stress, 7 exerted on a particle is: where h is the spacing between particles (0.59 p), a is the applied stress (110,000 psi), p, is the shear modulus of the matrix (6.7 X lo6 psi at 80O°C), and b is the Burgers vector of the matrix dislocation. From Eq. [I], the shear stress, 7, exerted on the WC particles when no recovery occurs is of the order of 6 X lo6 psi at 800°C. The limiting stress, F, that will

Jan 1, 1969