Search Documents

By G. E. Tooker

This paper (1) presents new data on the use of horizontal curves to optimize the alignment of belt conveyors. The operating concept of a horizontal curve is simple. As an element of the belt passes through the curve, it is motivated to drift toward the center of the curve by unbalanced tension forces in the belt. This lateral drift is resisted by the forces of friction and gravity, which in turn can be stated as a function of drift. Resisting forces, as a function of drift, are stated in terms of variables such as the amount of load on the belt, and parameters such as the trough angle, tilt angle, and super elevation angle, and number of rolls in the idler. The trick is to determine that the belt will drift to a position of equilibrium within predictable limits, without physically constraining the edge of the belt. In practice this prediction is not easy to make without the aid of a computer. The motivating force is easy to calculate, but its value is continually changing throughout the angle subtended by the curve arc. The resisting forces are constant throughout the curve for a given drift and load condition, but the calculations are very complex. Data in this paper will assist the conveyor designer in making preliminary calculations for horizontal curves. Presented is the equation for calculating the motivating force, and a family of curves that show the resisting force as a function of lateral drift for some commonly encountered conveyor design criteria.

Jan 1, 1985

By Alfred Jr. Petrick, William A. Vogely

INTRODUCTION The scope of mineral finance extends beyond the economic aspects of property evaluation to all of those activities involving acquisition and utilization of funds with an objective to optimize the value of the firm. It must, therefore, en- compass consideration of the overall financial goals of the firm, decisions involving external versus internal growth and domestic versus foreign investments, management of working cap- ital, efforts to minimize the cost of capital, and decisions with regards to the instruments of long- term debt and equity financing. The scope of this section is limited to considerations of special interest to the mineral or petroleum engineer, which include the following aspects of mineral finance: (1) The technical aspects of mineral or coal property or oil and gas reservoir evaluation which provide the basis for estimation and forecasting of revenues and costs. (2) Estimation and forecasting of costs and prices in a inflationary economic environment. (3) Calculation of cash flows which model .. , the investment in minerals, coal or oil, and gas. Such models require assumptions as to the timing of cash flows, escalation of capital and operating costs, base prices, and escalation, the tax regime, royalties, division of profits and the economic aspects of loans. (4) The role of discount rate in the economic analysis of an investment which requires consideration of the opportunity costs of the firm, cost of capital, risk premiums. (5) Risk analysis including application of the concepts of conditional net present value, expected value, and risk preference as well as the application of the techniques of sensitivity and simulation. (6) Selection of application criteria for in- vestment decision making. (7) Capital structure with particular reference to the effect of debt financing. (8) Consideration of sources of funds utilized by the minerals industries. (9) Long-range planning including portfolio analysis. This section is limited to principles, methodologies, and trends in mineral investment, finance, and long-range planning in the United States with a perspective from the year 1984. Consideration of the key concepts is supplemented by case examples of investment risk analysis and financial structure. Important factors affecting mineral investment evaluation during the 1980s include volatile metals prices, cost inflation, and the introduction of techniques requiring the computer and its capacity for improved technical and economic analysis into the hands of those who know most about the industry. The personal computer is replacing the calculator on the desk of the individual analyst and is rapidly becoming a required tool for the study of engineering and economics. Examples of change brought about by the micro-computer include greatly improved techniques of cost estimation, wider application of the computer for project analysis, computer graphics, reserve estimation, geostatistical analysis, mine design and other techniques that capitalize on the ability of the computer to handle

Jan 1, 1985

By Keith G. Papke

Jan 1, 1985

By A. Sainato, S. J. Kravits, G. L. Finfinger

This Bureau of Mines report describes and compares the procedures, capital investments, and operating costs of rotary and in-hole motor drilling techniques used to drain methane gas from the Pittsburgh Coal- bed in an underground mine located in southwestern Pennsylvania. A timestudy was conducted during the drilling of each of two boreholes, and the data were collated to serve as a base for comparing drilling procedures and operating costs. Findings indicate that drilling with an in-hole motor offers four advantages over rotary drilling; namely, an increase in drilling productivity, fewer worker-hours required, ease of maintaining vertical and horizontal bit trajectory, and less expensive drilling cost per foot of borehole.

Jan 1, 1985

By A. K. Sinha

Modern mine ventilation systems have grown rapidly in recent years both in tern of its complexities as well as its value for human health and safety. Although computer models are now available to help the design and operation of mine ventilation systems, considerable differences often exist between the computer based predictions and practical results. Research conducted to compare computer result with practical measurements made in ventilation circuits simulated in a physical model seems to confirm such differences. It is concluded that although a mine ventilation computer model is a very powerful tool, it can be utilized to its full potential only after more reliable input data are developed.

Jan 1, 1985

By Robert J. Collins

Computer-aided design drafting systems have been employed in plant design for nearly ten years. Current and future systems will include computer-aided engineering as well. This paper will explore the history and development of such systems including computer and workstation hardware, graphics software, and plant design applications software. The paper will also address future systems and will present both the system vendor and the mine mill designer's view. Specific examples of particularly successful applications will be included.

Jan 1, 1985

By Malcolm Scoble

The estimation of digging, ripping and blasting requirements in advance of mine production is a difficult task. The characteristics of the superficials and rock mass govern the type and intensity of ground preparation required as a prelude to loading. The incentives for optimum planning of preparation are primarily economic but also relate to mining method and equipment selection, productivity and environmental impact.

Jan 1, 1985

By Douglas R. Cook

The discovery of the gold deposits of the Jerritt Canyon district, with proven recoverable reserves in excess of 67.6 Mg (2.4 million oz) of gold, has contributed greatly to the tremendous resurgence in exploration for disseminated gold deposits in Nevada and throughout the west. The Jerritt Canyon project, including the Bell mine, is a 70130 joint venture between Freeport Gold Co. and FMC Gold Corp., both of which are wholly owned affiliates of the respective parent companies, Freeport-McMoRan Inc. and FMC Corp. The Jerritt Canyon district is located in the center of the Independence Mountains in north-central Elko County, Nevada, approximately 48 km (30 miles) northeast of the Carlin gold mine and 68 km (42 miles) north of Elko. Although the discovery of a commercial gold mine at Jerritt resulted from Freeport's exploration activities, the initial identification of a gold prospect in this area was a consequence of a program by FMC in the search for antimony. Their program was, in part, based on data in the Nevada Bureau of Mines Bulletin 61, "Antimony Deposits in Nevada." Work on the property began in 197 1 with geologic mapping followed by sampling and geochemical analyses. FMC geologists, including Robert Hawkins, Russell Hayden, and Hal Hurst recognized the striking similarity of the area to the geologic environment of Newmont's nearby Carlin gold deposit and soon focused on the gold potential. Increases in the price of gold served to stimulate interest and support for the exploration program. Geochemical samples were collected and analyzed for gold and trace elements usually associated with gold. A strong gold anomaly was found on the North Fork of Jerritt Canyon, which was called the Alchem anomaly. Drill-testing of this anomaly in 1973 revealed significant grades and thicknesses of gold mineralization in the lower portion of the Roberts Mountain formation. This initial discovery and subsequent close-spaced drilling proved the existence of several small pods of low-grade, gold-bearing material which cropped out at their up-dip edges, causing the surface anomaly. The mineralization was very encouraging, but was not, by itself, of economic importance from the standpoint of either grade or tonnage. Freeport Exploration Co. established a district office in Reno in late 1974 with responsibilities for exploration of hard minerals in the Basin and Range Province. Emphasis of the program was directed to the discovery of precious metal deposits. Enfield Bell, as District Manager for this new office, was particularly interested in the Independence Mountains and when the opportunity for a joint venture with FMC became available in 1976, it was aggressively pursued. Enfield Bell and David Stevens evaluated the FMC data and with the support of management formulated a bid in competition with 23 other companies. Freeport was selected by FMC as partner and a joint venture agreement was successfully negotiated. In mid-summer of 1976, Freeport Exploration Co. began an expanded program of detailed mapping and geochemical sampling under the direction of Bell and Stevens that led to new interpretations of the structural and alteration patterns. Hawkins' contribution during this period must be recognized since he not only was one of the original geologists assigned to the antimony and subsequently the gold investigations, but shortly after the start of the joint venture exploration, he was hired by Freeport Exploration Co. as the project geologist for the venture. Hawkins had studied the central Independence Mountains for his thesis and his understanding of the regional geology provided an excellent background for the continued exploration of the gold de- posits. His interpretation of the structure in the vicinity of the Alchem anomaly was of significant help in the Freeport exploration program. Drilling, based on this new under- standing of the geology, revealed the edge of the Marlboro Canyon ore body, which is now being exploited in the Bell mine. Although a classic bullseye geochemical target led to the discovery of the Alchem mineralization, the bulk of the reserves known today in the Marlboro Canyon area lay

Jan 1, 1985

By Arel B. McMahan

The U.S. Bureau of Mines investigated mines, prospects, and mineralized areas in the Owlshead Mountains Wilderness Study Area (WSA) in 1982. Within the WSA, subeconomic manganese, iron, zinc, and lead resources were identified at two mines; sample analyses indicate five other mines and prospects may have gold, silver, iron, manganese, and copper resources. Three mines examined adjacent to the WSA have identified manganese and iron resources; and sample analyses indicate manganese, iron, and gypsum resources may exist at two prospects. Greatest likelihood for future identification of mineral reserves is for manganese at the Black Magic Mine in the southeast part of the WSA. The southern half of the WSA contains nearly all identified mineral resources, and properties at which sample analyses indicate additional resources. The most significant are manganese and iron resources at the Black Magic Mine in the southeastern part of the WSA; and the Ellie, New Deal, and Owl Hole Mines adjacent to that part of the area. Manganese and iron minerals filled fractures and replaced limestone in brecciated and faulted contacts with intrusive granitic rocks. In the southwest corner of the WSA, sample analyses indicate four prospects may have gold and silver resources. These precious metals are in gouge zones along contacts where diorite has intruded volcanic rocks. A small identified resource at the Kennedy Boys Lead Mine in the western part of the WSA consists of quartz veins with zinc and lead minerals along a brecciated contact between granite and limestone roof pendants.

Jan 1, 1985

By R. Blickensderfer

The laboratory wear testing capabilities of the Bureau of Mines are described, Wear tests are used to support the Bureau?s research efforts toward reducing the wear of equipment used for mining and minerals processing and any wear involving a loss of strategic or critical materials. The emphasis is on abrasive wear because it accounts for most of the wear losses that occur in mining and minerals processing equipment, Spalling wear, caused by repetitive impact in grinding equipment, also is included, Ten abrasive wear tests, including high- stress and low-stress and two-body and three-body conditions, are described: dry-sand, rubber-wheel abrasive wear; Taber Abraser; abrasion resistance of refractory materials; dry-particle erosive wear; elevated-temperature, dry-particle erosive wear; low-angle slurry pot; jaw crusher gouging wear; ball mill wear; pin-on-drum abrasive wear; and high-speed impact gouging. Two repetitive impact tests are described: ball-on-block impact-spalling and ball-on-ball impact-spalling. Test equipment, procedures, and specimens are described, and typical test results are presented and discussed.

Jan 1, 1985

By N. Cruickshank

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst-prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) micro-seismic activity. Geophysical and engineering methods for detecting these characterisitcs are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1985

By Jerome P. Downey

Treatment of tungsten ore at Anschutz Mining Company's Chicote Grande (Bolivia) operation results in a relatively high grade arsenopyrite byproduct stream. Laboratory and miniplant testwork have been performed at Colorado School of Mines Research Institute to examine the technical feasibility of recovering a marketable arsenic product fr an this source. Process selection was constrained by the remote location of the millsite, which demands an uncomplicated, low maintenance operation. As a result of the research effort, a two-stage roasting/condensing process was developed, featuring the use of an indirect heating method. Arsenic was efficiently extracted and the arsenic trioxide (As203) product consistently exceeded the industrial purity specification of 99.5%. Key process parameters have been secured for extrapolation of the process to pilot or small commercial scale.

Jan 1, 1985

By D. T. Couillard

Video technology is becoming an important tool for many designers of industrial training programs. This report describes how trainers at the Minntac Mine, Mt. Iron, MN, have developed videocassettes of safe job procedures (SJP's) for training miners assigned to perform unfamiliar work tasks. All steps necessary for videocassette production, from idea to finished product, as well as the required equipment and prices, are listed and/or briefly explained. Minntac officials believe that the SJP videocassettes have contributed significantly to a reduction in mine accidents.

Jan 1, 1985

By H. C. Siebert

According to the "Survey of Energy Resources 1980" (1)*, which was prepared by the Federal Institute for Geosciences and Raw Materials in Hannover (FRG)for the World Energy Conference 1980 in Munich, the world coal deposits are assessed at 775 billion tce proven reserves 448 billion tce of them recoverable and 6 161 billion tce additional resources. If one ignores growth rates, the current world coal output of 2,8 billion tpy gives our recoverable reserves a static life expectancy of 175 years. With an average increase in world output of 3,2 % like between 1973 and 1980 this range would be further shortened to an alarming degree. Furthermore, the criteria used to distinguish between workable and unworkable resources give rise to the suspicion that deposit characteristics are not always taken into account to a sufficient degree. For example, little attention is paid to major ?Bonitaet" - factors such as dip and seam thickness. There have been wide-ranging scientific discussions on the lower limit for workable coal resources, but no such limits have been set at the other end of the scale. Otherwise it is well known that performance and costs are badly affected den in level and moderately inclined seams the seam thickness is more than 4 to 5 m, because special mining methods have to be used beyond this limit. These are associated with significantly higher costs than with the winning of seams of ?normal? thickness.

Jan 1, 1985

By R. B. Prater

The Bureau of Mines conducted research to separate the F from byproduct Zn concentrates obtained from fluorspar (CaF2) production, as part of the Bureau's effort to devise efficient, environmentally acceptable technology for recovering Zn from resources considered undesirable by Zn producers. Sulfuric acid (H2SO4) was found to be effective in F removal, while ammonium carbonate [(NH4)2C031 was not. The most important variables for reducing the necessary residence time were found to be temperature and agitation. Optimum leaching conditions were 75° C and 500 r/min for 2 h at 40 pct solids with 0.2 g acid per gram of concentrate, which resulted in a 98.3-pct F extraction. Zinc losses during F removal were in the range of 2 to 3.3 pct. Other elements such as Fe, Cd, Ca, and Cu were also partially dissolved. About 93 pct of the F was removed from the leach solution by neutralization and precipitation with calcium hydroxide [Ca(OH)2]. Additional treatment might be necessary to limit the buildup of soluble elements in the recycled leach solution.

Jan 1, 1985

By M. Hodgson

The redox reactions that occur on pyrrhotite and pentlandite in contact with oxygenated deionized water were examined using voltammetry. Reactions were put forward in which both minerals were progressively hydroxylated to form thermodynamically metastable surface intermediate products. These intermediates were modelled as metal deficient sulphides where a sulphurous layer was coordinated onto the remaining metal sites via polysulphides. Prior to hydroxylation pentlandite exhibited changes in the surface stoichiometry which were not related to pH effects. The formation of polysuiphide-sulphur intermediates were believed to promote collectorless; flotability for the two minerals. Microflotation tests (0.3 g samples) verified that the surface potential and particle size affected the flotation response, excessive oxidation inhibiting the minerals' flotability. Larger scale tests using ore samples (30 g) confirmed that the extent of pulp oxidation, particle size distribution and the presence of frothers affected the flotation response, the findings being in accordance with the postulated model for the hydrophobic species generated on the pentlandite and pyrrhotite surfaces.

Jan 1, 1985

By J. H. Shillabeer

"Rational exploration requires the prior selection of areas possessing excellent geological potential and minimum hazards to commercial development . Within an over-all strategy of grass-roots exploration, two procedures for selecting areas for (i) coal and (ii) metals exploration are described. The procedures explicitly balance infrastructure requirements and environmental concerns for areas of geological merit not alienated in parks and reserves. Through consensus, priorities are attached to those areas meriting closer scrutiny and field reconnaissance.IntroductionMining companies need to know that having made a potentially economic discovery, they will be allowed to develop it with minimum delay and at reasonable cost. The environment for exploration in British Columbia is complex and recent experience suggests that conditions are not becoming any easier. Conflicts over land use issues, preservation and economic development are common. The high cost of exploration requires that the risks should be offset where possible by: (i) carefully selecting the areas in which to work (ii) conducting operations in a responsible manner, and (iii) working cooperatively with the community of interests. This paper concerns the first action: prior selection of areas.To aid exploration planning at Suncor, a procedure was developed to grade those areas of the province possessing favourable geology according to the ease with which a mine might be developed . This had to be done within the constraints of the company's over-all approach to exploration. This emphasizes ""grass-roots"" exploration of self-generated projects in British Columbia. In addition, having selected a favourable belt of rocks, it is intended to persevere there while steadily adding to the accumulated data base and local experience. Hence, it is intended to concentrate on an area. This implies a long-term commitment to an area which in turn increases the importance of the original selection.Suncor's search is directed to finding base and precious metals in intrusive and volcanic environments, and export quality coal."

Jan 1, 1985

By Kevin Connor

There was little change during 1988 in the production of minerals in Burundi. The Government of Burundi, which banned all commercial mining operations in the country in 1979, lifted the ban on mining of alluvial gold deposits and started a program of small-scale artisan gold mining in October. Along with the legal mining of gold, licensed gold trading counters were established. Other mineral commodities produced were kaolin clay, lime, and peat. In compliance with the Government ban, the only mineral wealth exploited for commercial sale and export was alluvial gold. Through financial assistance from the International Bank for Reconstruction and Development (World Bank) and the United Nations Development Program (UNDP), a study to inventory the country's mineral resources continued throughout the year. As part of this study, during the year, a West German company undertook a drilling program to further outline the nickel reserves of the Musongati area in central Burundi. Results of the work as of yearend were disappointing, with only 12 million tons of ore identified with better than 2% nickel content proven. Investigations also continued during the year regarding the centrally located deposits of vanadium-bearing titaniferous magnetite. A Norwegian company contracted to prepare a prefeasibility study for developing the deposit. The British Sulphur Corp. Ltd. was nearing completion of its $1.2 million2 study of the phosphatic limestone deposit at Matongo-Bandaga at yearend. Ore reserves of about 17 million tons grading 11% phosphorus pentoxide (P2O3) had been identified. The phosphate zone overlies a carbonatite rock, which could provide the basis for a cement industry. Additional drilling was planned for 1984. Exploration for gold was underway in 19S3 in northern Burundi through UNDP funding. Several primary deposits of shallow semimassive sulfides with gold values ranging from traces to 11 grams per ton had been discovered. With assistance from the Federal Republic of Germany, bastnasite reserves of 5,400 tons, with associated high europium oxide and cerium content, were verified, and the prospects for finding

Jan 1, 1985

The Bureau of Mines Minerals Information organization collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7. 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Minerals Information activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1985

By Jansen N

Production from the narrow, high grade silver-lead-zinc orebodies below 15 level commenced in mid 1985.Geological, mining research and recent mining experience determined that a mechanised drill, fire and muck cycle would be the most suitable method.Ground conditions are predicted to be worse than in other cut and fill (MICAF) areas at Isa Mine, owing to the increased depth, more variable dip of the orebodies and the increased effect of major geological structures.Mechanised ground support and tight filling techniques feature in controlling these expected adverse ground conditions.

Jan 1, 1985