Search Documents

By O. Worku, J. H. Masliyah, Z. A. Zhou

ABSTRACT The viscosity of concentrated kaolinite or illite clay in aqueous suspensions was measured in the presence and absence of a small amount of montmorillonite (<1 wt%). To avoid solids settling and to increase the sensitivity of the suspension viscosity measurements, solids concentrations higher than 38 wt% were used. The pH of the suspensions and the concentration of calcium and bicarbonate ions were found to significantly impact the viscosity of the clay suspensions. The results showed a significant increase in the viscosity of kaolinite suspensions with the addition of as low as 0.25 wt% of montmorillonite on a solids weight basis. In addition to illustrating the role of water chemistry in modifying slurry rheological properties, our study demonstrated that viscosity measurement could be a simple, yet sensitive technique for determining the content of smectite clays, such as montmorillonite, in a complex mix of various types of clay.

Jan 1, 2012

By Guillermo Turner-Saad

"Best practice in the economic evaluation of mining projects and operations is based on the integration of geological, mining, metallurgical, environmental, marketing, economic and corporate information and strategies. Fundamentally, the economic evaluation takes into account mining, blending, stockpiling, processing, smelting, refining and marketing ore resources with grades estimated by geostatistical methodologies.Nevertheless, a realistic economic evaluation consists of a concurrent and integrated optimization process that maximizes the concentrates or products of liberated and selected ore minerals from mineral deposits. The optimum solution is obtained through a trade-off among mining, blending, stockpiling and processing ore reserves with distinct mineralogy and texture characteristics. The concurrent optimization determines both the practical mining sequence of ore reserves and the dynamic and robust mineral processing flowsheet design over the expected life of mining projects and operations.A combined risk-adverse and concurrent optimization process takes into account the spatial uncertainty of the mineralogy and texture characteristics of ore reserves. Additionally, a variety of mineral processing linear, non-linear, additive and non-additive parameters modeled spatially. The spatial uncertainty of these ore reserves characteristics and parameters has a direct impact in the expected mining sequence, mineral processing flowsheet design, concentrates or products quantity and quality, and economic value of mining projects and operations.Geometallurgical domain constrained stochastic geostatistical methodologies and multivariate mathematical models are applied for spatial uncertainty modeling of ore reserves characteristics and parameters. These mathematical models correlate the mineral processing liberation and selectivity responses of the mineralogy and textures within each geometallurgical domain. These models, in turn, are defined based on results of mineral processing and environmental testwork of unbiased and representative samples chosen for their variability. These samples are selected within mutually exclusive spatial geometallurgical uncertainty domains with similar mineralogical and textural characteristics in mineral deposits.Geometallurgical domains are defined by applying and combining multivariate statistical analysis and implicit modeling methodologies. These involve determining and constraining mineral processing liberation and selectivity properties explicitly contained in the extensive and integrated exploration drillhole database."

Jan 1, 2010

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013

By Peter N. Calder

Long range mine planning involves developing a mining sequence that schedules the extraction of the ore and waste materials within a final pit limit. The objective is to define a sequence that best meets the defined strategic objectives. The main steps in the creation of an open pit mine plan are the final pit limit design, the design and sequencing of the mining phases, equipment selection and operating cost estimation. Flexibility is the key strategic element in developing a mine plan. Planning the extraction sequences and rates for the various mining areas is a challenging and demanding activity. It is often necessary to consider numerous alternative strategies and what if scenarios. The number of alternatives that can be studied with limited manpower and time resources is restricted. In order to investigate strategic aspects of mine planning, a system to generate workable mine plans rapidly is required. The concept of Visual Mine Planning is that the engineer can visualize the current plan, easily change a component of the plan, such as the annual cut-off grade schedule or the production rate within a particular Phase, and immediately see the effect on the mineralogical and cash flows. If the desired result is not achieved, a change is made and the effect is again immediately seen. This paper presents results of research in this area conducted at the Pontificia Universidad Católica de Chile. The work includes the examination of cut-off grade strategy, sequencing, blending, stockpiling and shovel-truck fleet requirements using simulation.

May 1, 2003

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By Wei Sun, Jaewon Choung, Zhenghe Xu, Zhangming Cui

"High intensity conditioning has been demonstrated in a number of cases to enhance fine particle flotation. The improvement could be attributed to the enhanced formation of particle aggregates. However, the understanding of aggregation mechanisms remains rather limited. Recently, an enhanced particle aggregation was observed by the formation of small air bubbles resulting from high intensity agitations (HIA). In this study, a novel visualization system is designed and constructed for characterizing the fine bubbles formed in an HIA cell. The new design allows determination of gas evolution and bubble size distribution. With this system, the effect of dissolved air on fine bubble generation by HIA is investigated. The results show that HIA creates a favorable environment for the formation of gas nuclei and small size bubbles due to hydrodynamic cavitation.INTRODUCTIONFlotation is a dominant separation technique employed by mineral industry to recover the valuable mineral particles. However, in general, particles finer than approximately 10 µm are not effectively recovered by conventional froth flotation technique due to their low inertia and high specific surface area (Fuerstenau, 1988). Therefore, the fine particle flotation has been considered as the central challenge of flotation research. Substantial advances have been made for fine particle flotation from both a theoretical and technological point of view (Fuerstenau et al., 1979; Song and Lu, 1990; Subrahmanyam and Forssberg, 1990; Sivamohan, 1990; Sedat and Barry, 1991; Matis, 1995). High intensity agitation (HIA), for example, has found some success to improve fine particle flotation kinetics in laboratory tests (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998; Rubio and De Brum, 1994).The effect of mechanical agitation on flotation kinetics has been recognized for many years. In mid-1970s, Warren (1975) reported that increasing the shear rate of the pulp could improve the efficiency of ultra fine particle flotation. He attributed this improvement in flotation to the formation of aggregates. This concept of aggregation has been extended by Rubio (1978), and Bulatovic and Salter (1989), who employed high intensity agitation (HIA) method to promote aggregation. They found that HIA with the addition of collectors, frothers and suitable modifiers significantly improved both the flotation recovery and selectivity of ultra fine sulphide minerals. The improvement was explained by warren’s shear flocculation theory. Till now, many studies (Chen et al., 1999a and 1999b; Valderrama and Rubio, 1998) have been undertaken to improve fine particle flotation by HIA. However, most of these studies were focused on the relation between energy input and flotation efficiency. Less information was available for describing how the aggregate formed during HIA process."

Jan 1, 2006

By D. C. Fraser

"Geophysical Engineering and Surveys Limited of the Keevil Mining Group have routinely conducted ground surveys with VLF-EM receivers for the past two years. Both Crone's Radem and Ronka's EM16 have been used.VLF-EM dip-angle data often yield complex patterns which require considerable study for a proper interpretation. A method was developed which allows field operators to transform the noncontourable dip angles into contourable data, producing conductor patterns which are immediately apparent to exploration personnel untrained in VLF-EM interpretation.VLF-EM contoured data generally peak very close to the top of a conductor, thereby allowing drill holes to be spotted accurately. However, the data generally should not be used alone to select drill targets because structures may be sufficiently conductive to yield strong anomalies. Thus, magnetic and/or vertical-loop EM correlations may be considered as necessary criteria for drilling.VLF-EM surveys can replace IP surveys in certain environments. For example, the Restigouche orebody in the Bathurst camp of New Brunswick yielded a VLF-EM anomaly as distinct as that obtained by IP, although the body did not respond to vertical-or horizontal-loop EM. However, the cupriferous breccia pipes of the Triba mine near Batchawana, Ontario yield strong IP anomalies but not VLF-EM anomalies, illustrating that disseminated ore targets should be sought with IP rather than with VLF-EM."

Jan 1, 1971

By Garnet T. Page

"ABSTRACTThese societies •can help in such aspects of a vocation.al guidance program in secondary schools as: provide vocational and technical information, and assist with vocational exploration, such .as plant visits, films, etc. -as .an aid to the student in making a self-inventory. Evidence is increasing that employers' needs for engineers and scientists will not be adequately met in the future. Therefore, the E.I.C., C.I.M., .and C.I:C. recently revised and extended the activities of the Canadian Counselling Committee on Engineering and Science. This co-•operative .action is to be integrated with the educational system, nationally .and locally, and with provincial associations •of engineers and other groups interested in the provision of vocational information in engineering and science.DEFINITIONTHE scientific treatment of any subject requires consistent use of carefully defined terms. The National Vocational Guidance Association of the United States studied the problem of the definition of vocational guidance for .about 16 years, and in 1937 finally arrived at:""Vocational guidance is the pro-cess of assisting the individual to choose an occupation, prepare for it, enter upon and progress in it. It is concerned primarily with helping individuals make decisions and choices involved in planning a future and building a career -decisions and choices necessary in effecting satisfactory vocational adjustment.""RANGEAs a school enterprise, vocational guidance begins at that point in the individual's life when he finds it necessary to make choices that have a definite significance for his future vocation."

Jan 1, 1952

By P. Simon, G. Falkinger, G. Angerer, B. Gerold

"This contribution presents an investigation of the evolution of shrinkage pores during hot rolling with a special focus on the microscopic mechanism. The reliable closure of pores, which inevitably occur during the casting process, is of crucial technological importance for high-quality hot rolled plate products. Therefore, lab-scale tests were carried out under different typical thermomechanical loadings. Extensive data from optical microscopy was collected before and after deformation. The analysis shows that the average volume of pores evolves similar to the volume of an idealized arrangement of voids in an ideally plastic matrix. The average shape of the shrinkage pores, however, was found to be almost constant during deformation. Even though individual pores exhibit complex morphologies far from any idealized geometries, the overall evolution of a large number of pores is well captured by simple assumptions. In addition to the quantitative analysis, a schematic representation of this counter-intuitive behavior is provided. A simple ‘Gurson’-type void evolution equation was implemented in a three-dimensional Finite-Element model of the industrial hot rolling process. With the help of this mechanism-based process simulation the thermomechanical closure of shrinkage pores during the rolling process has been optimized for a variety of plate products.INTRODUCTION Aluminum alloys of the 7xxx series are widely used in the aircraft industry. They have to meet high quality standards regarding microstructure as well as mechanical properties. For hot-rolled aircraft plates, one of the most important quality requirements is that they are free from pores. Pores, however, are inevitably created during the casting process either due to shrinkage or due to the dissolution of gas from the melt. The pores have to be closed mechanically during the hot-rolling process. Therefore, the mechanism of so-called pore closure or void closure has a high technological relevance for the production of aircraft plates. The behaviour of voids in a ductile matrix subjected to mechanical deformation has been extensively studied, especially in the context of damage mechanics. A recent review (Besson et al., 2010) on modeling methods for ductile damage gives a good impression on how much experimental as well as theoretical effort has been dedicated to the problem of void evolution under mechanical loadings. Although void closure has been studied to a far lesser degree, it obeys to the same general theoretical evolution laws as void growth. The most basic theoretical result is that hydrostatic pressure drives void closure, while hydrostatic tension leads to void growth. The mechanism of void closure depends on the void shape. This is illustrated by the example of a flat penny-shaped void, which under compression obviously closes much faster than a sphere with the same volume. Theoretical models have been developed for the evolution of simplified void geometries, such as spheres or cylinders (e.g. Gurson, 1977), spheroidal (Gologanu et al., 1997) and ellipsoidal voids (Ponte-Castaneda, 1994). In industrial cast ingots, however, the pores exhibit very complex morphologies, which are far from any idealized geometry. X-ray tomography revealed ‘tortuous’ voids in a 5xxx aluminium alloy (Chaijaruwanich et al., 2006)."

Jan 1, 2018

By Fathi Habashi

Teaching mining, metallurgy, and geology preceded that of the other engineering disciplines. The first School of Mines was founded in 1756 in Potosi (Fig. 1) in New Spain (now Bolivia), 38 years before the first Polytechnic School (École Polytechnique) was founded in Paris. The schools of mines were also pioneers in the teaching of chem- istry. The teaching staff at these schools cre- ated the basic literature on metallurgy, mining, and geology. They analyzed and dis- covered numerous minerals and discovered the metals tungsten, beryllium, chromium, uranium, zirconium, vanadium, indium, and germanium. The history of some of the first schools is given together with biographies of some of their distinguished teaching staff.

Nov 1, 1997

By Fathi Habashi

This Historical Metallurgy Note is the second part of a three-part series, the first of which appeared in the November- December issue of the Bulletin. Part III will be published in February, 1998. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940-1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of his Institute.

Jan 1, 1998

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998

By Fathi Habashi

Extraction by organic solvents is a chemical process in which metal species in the aqueous phase react with an organic reagent to form an organometallic com- plex, thus, the metal species leave the aqueous phase and enter the organic phase from which it can be stripped back in the aqueous phase to obtain a pure and a concentrated solution. The metal in the organic phase is not bound to carbon atoms as in organometallic compounds but to oxygen, nitrogen, sulphur, or hydrogen by a co-ordination (dative) bond (Habashi, 1999).Solvent extraction was used for the first time in hydrometallurgy in connec- tion with the special and urgent materials requirements of nuclear energy during World War II. A plant was constructed in the United States for the preparation of high-purity uranyl nitrate solution. In this plant, the yellow cake (a high-grade sodium or ammonium uranate) was dis- solved in HNO,, and uranium was selec- tively extracted by ether then stripped by water to give a concentrated solution of pure uranyl nitrate. This was gradually followed by developing methods for other high-priced metals such as plutonium, thorium, niobium, tantalum, zirconium, hafnium, boron, beryllium, and molybde num. The second step took place in the 1960s when solvent extraction was applied for the first time to extract a rela- tively cheap metal-copper. At present, solvent extraction technology is wide- spread, well accepted, and highly efficient. Solvent extraction had its origin in the discovery, by Christian Friedrich Bucholz (1770-1818) in 1805, that uranyl

Sep 1, 1999

By K. Sugawaral, W. Tongampl, K. Hiruta, Takasaki Y., A. Hosoi, T. Katol, A. Shibayamal

Printed circuit boards of discarded personal computers, televisions, mobile phones and so on contain a significant amount of valuable metals. For the recycle of valuable metals contained in the printed circuit board wastes (P CB W), the effect of temperature on chlorination-volatilization of metals under chlorine gas flow was studied. The experimental sample used was powder of two types: crushed PCBW (Sample 1) made from PC and industrial machines, and crushed-combusted PCBW (Sample 2) made from Sample 1. The principal element in Sample 1 and Sample 2 was copper, about 13 wt% and 20 wt% respectively. Sample 1 was composed of pure metals such as copper, tin and lead. In comparison, Sample 2 consisted of oxide metals such as copper oxide, tin dioxide and silicon dioxide. The two samples were heated at predefined temperatures (ranging from 300 °C to 900 °C) in chlorine gas. The chlorine gas flow into the furnace was set at a rate of 100 mL/min. As a result, copper in Sample 1 began to volatilize at 600 °C and completely vaporized at 700 °C. While in Sample 2, copper started to volatilize at 600 °C and reached 100% vaporization at 800 °C. For Sample 1, zinc finished volatilizing at 500 °C, while for Sample 2, zinc volatilization reached only about 80% (maximum). Also, lead, nickel and titanium showed similar results. Consequently the volatilization rate of Sample 1 is higher than Sample 2 and the temperature dependency was verified for copper, lead, zinc, nickel, antimony, titanium and chromium. In fact, the volatilization rate of these metals increased with the temperature. This result reflects the difference between pure metal and metal oxide, as Sample 2 was combusted before the chlorination-volatilization test. Moreover, the chlorination reaction may be accelerated by a reductive atmosphere because Sample 1 contains carbon. In this study, the volatilization behavior of some valuable metals in PCBW by chlorine gas was observed. Further improvement in the rate of volatilization can be achieved by optimizing the experimental conditions.

Jan 1, 2011

By Alan J. Wianwright

Introduction ??New world-class Upper Devonian porphyry Cu-Au system located in south Mongolia ??6.5 km NNE-trending mineralized corridor ? 4 discrete deposits ??Southern Oyu deposits: Chalcopyrite, deposits: bornite ??Hugo Dummett: Zone: Hypogene chalcocite in addition to chalcopyrite and bornite ??Total resource exceeds ~2 Gt@ >1% Cu, >0.25 g/t Au (0.6% Cu equivalent cut-off) (Ivanhoe Mines press release, 2005)

May 1, 2006

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By Marie-France Caille, Carl Caumartin

"Audrey Resources' Mobrun Mine is located in Dufresnoy Township some 30 km to the northeast of Rouyn-Noranda. The Mobrun tine deposits consist of two major massive sulphide lenses; the newly discovered 1100 lens located 450 m south of the Main zone, and one ntellite lens, the 850-870-930 complex.The 1100 lens is hosted in a large pyroclastic unit bounded to the mouth by rhyolite and andesite flows and by a thick rhyolite unit to the art h. stratigraphically belon the three lenses. It consists of approximately 15 Mt of massive sulphide, of which 10.4 Mt are of economic ade. The Main lens lies comformably above thick rhyolite flows, ecciated and pyritized by the sulphide horizon, and is overlain by ttercalated ash tuffs and rhyolites which host the over-lying satellite ns. The Main lens consists of 3,3 Mt of massive sulphide, of which 523 000 tgrade0.80% Cu, 2.44%Zn,30.19 g/t Ag, and2.2 g/t Au he richer satellite lens (180 000 t) is part of the same volcanic stem and resulted from a resurgence of hydrothermal activity. ructure played a role in the final geometry of the deposits but did not eatly affect the volcanogenic and stratabound nature of the lens. Total production since the start of operations in 1985 amounts to 58 000 t and is restricted to the Main lens. Production from the 100 will come onstream in 1992 as ore reserves from the Main and e satellite lenses are exhausted.RESUMELa Mine Mobrun de Ressources Audrey inc. est située dans le mton Dufresnoy, a quelque 30 km au nord-est de Rouyn-Noranda. lle comprend deux lentilles de sulfures massifs d’importance majeure ~i sont les lentilles 1100 et Principale, et une lentille satellite qui est complexe 850-870-930.La lentille 1100, la plus ancienne, est contenue dans une épaisse 1ite pyroclastique bordée, au sud, par des coulées de rhyolite et d’andésites, au nord, par une épaisse unité rhyolitique. Cette lentille contient environ 15 Mt de sulfures massifs dont 10,4 Mt à teneur économique. La lentille Principale repose sur d’épaisses coulées rhyolitiques brechifiees et pyritisees à proximité de l’horizon de sulfures; elle est recouverte de tufs a cendres et de rhyolites interlitees qui contiennent la lentille satellite. La lentille Principale est constitute de 3,3 M t de sulfures massifs dont 1 523 000 t sont économiques avec une teneur moyenne de 0,80% Cu, 2,44% Zn, 30,19 g/t Ag, et 2,2 glt Au. Faisant partie de ce second épisode volcanique, la riche lentille satellite (180 000 t) temoigne d’une recrudescence de l’activité hydrothermale. La structure joue un rôle important dans la géométrie finale des dépôts mais ellen' affecte pas, de fa~on significative, la nature volcan génique des lentilles. Depuis le début des opérations, en 1985, la production totale est d’environ 568 000 t, provenant essentiellement de la lentille Principale. La mise en production de la lentille 1100 est prévue pour 1992, alors que les réserves des lentilles Principale et Satellite seront probablement épuisés."

Jan 1, 1990

By A M. Goodwin

Detailed stratigraphic studies in the Birch-Uchi Lakes area have shown that the volcanic components are arranged in superimposed sequences, or cycles. Each cycle displays a progression from predominantly mafic effusives below to predominantly felsic extrusives above. Sedimentary rocks are preferentially associated with the felsic extrusives. Two volcanic cycles are represented. The average stratigraphic thickness of the volcanic rocks present is 31,000 feet. The original volcanic pile was probably in the order of 40,000 feet thick. The present lithologic composition is estimated to be: mafic volcanic rocks, 60 per cent; felsic volcanic rocks, 27 per cent; sedimentary rocks, 10 per cent; and others, 3 per cent. Gold occurrences are preferentially distributed with respect to the volcanic succession. Of fifty recorded occurrences, thirty-nine are located in the upper felsic division of the lower volcanic cycle; forty are associated with closely interbanded daciterhyolite pyroclastic rocks, andesitic lavas and siliceous sediments. The gold-bearing quartz veins either lie at the contacts of enclosing lithologic units or occupy cross-cutting fractures in one or more adjacent units.

Jan 1, 1965

By Harold L. Gibson, David H. Watkinson

"Volcanogenic massive sulphide deposits of the Noranda Camp cur throughout the Noranda Shield Volcano but are concentrated and along the margins of the Noranda Cauldron. The deposits are realized along synvolcanic faults that also accommodated subsince and controlled the location of eruptive centres. Deposits within e 3 000 m thick Mine Sequence formed during a period of active volcanism and subsidence coinciding with the onset of two cauldron subsidence cycles. The Noranda Cauldron was a restricted site of 10malously high heat flow and structural permeability that favoured e development of a high-temperature hydrothermal system. Metals may have been derived from leaching of aquifer rocks by convecting a water or directly from a shallow underlying magma chamber, now presented by the Plavrian Pluton, that was at its highest position !thin the crust during cauldron subsidence. The deposits formed rough a combination of sulphide precipitation from exhaled fluid td replacement at and below the seafloor in a manner analogous to ose on the modern seafloor.RESUMESi les dépôts de sulfures massifs volcano gènes du camp minier de ~uyn-Noranda sont présents dans les différentes parties du volcanluclier de Noranda, ils se trouvent concentres toutefois, en plus ·and nombre, sur le pourtour de la caldeira (cauldron) de Noranda. ~s dépôts sont localises le long des failles synvolcaniques qui ont cilite la subsidence et contrôle la position des centres d’éruption.~dépôts situes dans la séquence des mines (3 000 m d’épaisseur) sont formes durant un épisode d' activité volcanique et de subsiden qui coïncide avec l' amorce de deux cycles d' affaissement de la rldera (cauldron) de Noranda. Celle-ci Jut le site exclusif d’unflux : chaleur anormalement élevé et d’une perméabilité d’origine cucturale qui ont favorise le développement d’un système hydrothermal a haute température. Les métaux proviennent soit directement d’une chambre magmatique situee afaible profondeur, so it d’un lessivage des roches de l’aquifère par l’eau de mer circulant par convection. Cette chambre magmatique, représentée maintenant par le pluton de Flavrian, se trouvait à son niveau le plus élevé dans la croute au moment de l’affaissement de la caldeira (cauldron). Les dépôts se sont constitués par un mecanisme combinant remplacement et précipitation de sulfures à partir des fluides exhalatifs, au niveau ou au-dessous du plancher océanique, de la même manière que se forment de nos jours, les dépôts de sulfures massifs au fond des océans."

Jan 1, 1990