Search Documents

By Steven Wright

The reduction of a slag produced 6om the recycling of lead batteries was studied in a kilogram scale laboratory investigation by reacting with graphite at temperatures of 1180 and 1200°C. Simultaneous reduction of PbO, Fe203, Sb203 and As203 occurred with the Sb and As reporting to the metal while the lead content in the slag was above 2 wt%. The Sb and As distributions between metal and slag were strongly affected by temperature and slag oxidation state. The rates of reduction of PbO and Sb203 increased with increasing slag basicity and temperature and decreased as the PbO content in the slag decreased. The reduction rate of PbO from these slags was similar to other industrial lead slags at the same CaO/SiO2 ratio and temperature. The implications of the behavioural similarities of the antimonous slags during reduction with carbonaceous reductants and other lead slags are briefly discussed.

Jan 1, 1994

By C. R. Palmer

The Bureau of Mines investigated the use of ion-exchange technology for the recovery of precious metals from cyanide leach and spent electrolytic solutions. This research included adsorption of gold and silver on both weak-and strong-base anion-exchange resins. The effects of nickel, mercury. and iron on precious metal loading of strong-base resins were also determined. Due to the nonselectlvity of strong-base resins, selective elution also was investigated. Both commercially available and experimental weak-base anion-exchange resins were tested. None of the commercial weak-base resins tested were suitable for a caustic-cyanide system owing to their low recovery of precious metals at pH 10 or above; however, three experimental resins have possible application. Continuous tests conducted with mill cyanide solution in a multicompartmented ion-exchange column using strong-base anion-exchange resins adsorbed nearly 100 pct of the precious metals as well as the iron and nickel. During the elution of this loaded resin the iron was first removed with NaCI plus NaOH; then nickel with dilute H2S04 or HCl; finally gold and silver with thiourea in dilute HCl.

Jan 1, 1988

By Guo Xian Jian

In this paper, an alternative process to recover the value metals from polymetallic gold ore by FeCh leaching was proposed. In the process, gold was recovered by direct cyanidation from the leaching residue, the isolative electrolyte in chloride solution was selected to recover lead, the cementation with copper powder was used to recover silver and the solvent extracting was applied to recover copper and zinc. The total recovery of gold, lead, copper, silver and zinc in the process is 90.8%,96.05%,84.3%,81.98% and 54% to the bullion of gold, lead and silver and sulfate of copper and zinc, respectively. The process conditions selected for FeCh leaching are the temperature of 104°C, leaching time of 6 hours, Fe3+ content of 140 g/l and stoichiometry of FeCl3.

Jan 1, 1996

By Leonid M. Lerner

High temperature aluminum Alloy 8009 is a rapidly solidified/powder metallurgy aluminum-iron-vanadium-silicon alloy. This alloy in combination with hard oxide aluminum film has unique engineering properties which may recommend its use in compressors and impellers for aerospace applications. Various anodizing processes (including Sanford Low Voltage DC+AC Process) for these task will be evaluated and normal chemical composition, physical properties, and macrostructures of 8XXX aluminum alloys will be presented.

Jan 1, 2006

By Leiv Kolbeinsen, Stian Seim, In-ho Jung

"The current work presents new experimental data in the iron-unsaturated region of the FeTiO3-Ti2O3-TiO2 slag system. The samples are prepared by melting pure reactants in a high frequency induction furnace that employs a cold crucible. A similar experimental set-up has been described in literature and proven suitable to investigate high titania slags. The FeO content of the samples range from 3.7 to 21.8 wt% and the Ti2O3 content range from 3.6 to 30.1 wt%. The liquidus temperatures of the samples are measured in-situ by a spectropyrometer and range from 1450 to 1645 °C.In addition, an improved thermodynamic database for the FeO-Ti2O3-TiO2 system has been developed. Ternary parameters have been included and optimized to fit previously published experimental data. This optimization minimizes the discrepancy between experimental data and thermodynamic calculations as previously discussed in literature. New liquidus projection plots are proposed for the FeO-Ti2O3-TiO2 and the FeTiO3-Ti2O3-TiO2 systems.IntroductionIlmenite (FeTiOs) smelting is a relatively small industry world-wide. However, a reasonable focus on the process has been applied in Norway due to the location of one such smelter in Tyssedal, which is located in the western part of Norway. The process is essentially carbothermal reduction, where most of the iron in the ilmenite is reduced to its metallic state, and the titanium oxide is concentrated in the slag product. The metallic iron is sold as a high purity pig iron and finds applications in cast products. The slag concentrate is further processed for the production of TiOvpigment and/or titanium metal. This further processing can be performed through different routes according to the purity of the slag concentrate."

Jan 1, 2012

By Baozhong Zhao

In-situ vitrification (ISV) is a new technology used for treating radioactive, organic and inorganic contaminated soils. In this process, electricity is applied through electrodes buried in the contaminated soil to melt it and form an environmentally stable glass-like solid. The organic contaminants and volatile metals are vaporized during heating up, the non-volatile inorganic elements are dissolved and incorporated into the melt. In present full-scale operation, the ISV process can treat 4 to 6 tons of soil per hour at consumption of about 1000 kwh per ton of soil. In this study, various configurations of electrodes were examined in a mathematical model. The results may be used to optimize the ISV process.

Jan 1, 1994

By W. G. Davenport

H20 is present in many flash furnace inputs. Examples are: (a) moisture in concentrate and flux (b) humidity in blast (c) moisture in hydrocarbon fuel, particularly coal, Appendix IV. H20 may also leak into the furnace from damaged water-cooling jackets. H2O, especially that it be included H2O, exerts a strong cooling effect on the flash furnace. It is important our calculations. As will be seen from the calculations, gaseous and liquid H2O both increase flash furnace industrial oxygen and oil requirements. This is because gaseous H2O (humidity in blast) must be heated from its input temperature to the flash furnace off gas temperature. Liquid H2O must be evaporated and heated.

Jan 1, 2001

By G. R. Adams, N. Y. Tang, N. Qiang

"Aluminum is the most important alloy addition to Zn baths for controlling the reaction kinetics between the steel substrate and molten Zn in continuous galvanizing operations. Due to the complexity of the Zn-Fe-Al ternary system, the measurement and control of effective bath Al remains a challenge for modem galvanizers. The successful development of Al sensors has made the real-time measurements of bath Al contents possible. To facilitate their application, a computer interface and a palm-size data logger have been developed by Cominco. Plant applications indicated that the sensor possessed sufficient accuracy for process monitoring and control. The working mechanism of the Al sensors and Cominco's development work is described, and the results of sensor applications are presented.IntroductionControl of bath Al content is critical in modem continuous galvanizing because it has a strong influence on coating structure and properties and the overall product quality. The control of effective bath Al content (Al in liquid solution) is particularly critical for galvannealing where a high bath Al content may lead to incomplete alloying during post annealing, and a low bath Al content may result in other operation problems, such as excessive bottom dross accumulation and difficulties in coating thickness control. The desirable accuracy of the Al control is within ±50 ppm of target levels. In principle, such an accuracy is achievable for modem chemical analysis facilities, such as atomic absorption photospectrometer (AAS) and induction-coupled plasma (ICP). However, a recent study carried out by the International Lead and Zinc Research Organization (ILZRO) indicated that such an accuracy is rarely achieved in the zinc and steel industries.(1)"

Jan 1, 1997

By I. M. S. Moraes

Caraiba Metais has a plant for the purification and the cristallization of the crude nickel sulfate removed from its copper electrolyte purification system. In November 1994, an interdepartmental group was formed to study the Q.F.D. method, through its application on the improvement of the quality of the nickel sulphate hexahydrate. The team, formed with representatives of the following areas : production, technology, marketing, sales, maintenance, laboratory and TQC office, had also the task of checking the applicability of the method to other products of the comp any. This paper describes the main steps such as the survey of customer's demands, the preparation o1 the quality matrix, stablishing the planned quality matrix, the planned and the designed quality, and the consequent identification of the engineering bottlenecks. It is also shown how these bottllenecks were studied and solved. The application of the method allowed the team to identify means of increasing the production capacity by 40%, to improve the intrinsic quality of the product (including packaging), and to increase the reliability of the process.

Jan 1, 1997

By John M. Boyle

The use of high vacuum mercury retort recovery as a safe and effective means of removing mercury from mercury hazardous waste solids rendering them non-hazardous and recovering mercury suitable for recycling.

Jan 1, 1995

By R. Nilsson

In the present work the sulphide capacities of Ca0-Mn0-Si0, ternary slags have been measured in the temperature range 1798 - 1873 K by equilibrating the slag with a gas-mixture containing CO, CO,, SO, and Ar. The results are compared with the data reported in literature. A theoretical model has been developed in the present work where the sulphide capacity is expressed as a function of the slag composition and temperature. The model enables the estimation of sulphide capacities of complex slags with a knowledge of the capacities of simpler systems.

Jan 1, 1994

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re-melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Tullio Corsini

Scrap battery recovery process, developed by Engitec Impianti S.p.A., is improved transforming batches operations in continuous. Benefits expected: constant and better quality of the products; easier and more reliable control of the operating parameters, reduction of manpower requirements. Paste will content less sulfate, particularly in soluble form. Sodium sulphate is obtained with higher and constant purity.

Jan 1, 1993

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994

By Kenji Morinaga, Shigeru Fujino

"Preparation and vacuum ultraviolet (VUV) transmission spectra of aluminum fluoroberyllate glasses, MgF2-CaF2-SrF2-A1Fr BeF2 (MCSA-Be) and MgF2-CaF2-SrF2-AlFrYFrBeF2 (MCSAY-Be), were studied. The influence of YF3 and BeF2 on the thermal stabilization against crystallization and VUV transmittance was investigated. With increasing the BeF2 content, the crystallization tendency decreased and the absorption edge shifted to shorter wavelength in the MCSA-Be and MCSAY-Be glasses. The MCSA-20Be glass composition exhibited the shortest wavelength UV absorption edge (-147 nm) and the highest transmittance at 157 nm (60% for 2 mm sample thickness). The transmission values at 157 nm and the slope (steepness) of the absorption edge were found to be significantly influenced by the trace amount of Fe2+ derived from the BeF2 raw materials.IntroductionPure beryllium fluoride is known to be an only fluoride that forms one component glass on cooling from the molten state and is structurally similar to silica with [SiO4]4- tetrahedra. Molten BeF2 is highly viscous with a viscosity of about 106 poise near its liquidus temperature at 550""C[l]. The addition of modifying fluorides such as LiF, NaF or KF to BeF2 substantially decreases the viscosity[2]. Glass forming region of binary fluoroberyllate glasses has been mainly reported by several authors [3]. LiFBeF2 binary system is structually analogy for Mg0-Si02 system from their phase diagram and ratio of ionic radius for each cation and anion, respectively. LiF-BeF2 binary glasses seems to be promising candidates for the extreme deep vacuum ultraviolet (VUV) transmitting optical materials owing to their larger band gap. However, it is chemically unstable, and so, have no practical application for lens systems in micro lithography equipments and substrate materials for F2 (157nm) excimer laser[4]. There are also few reports on the VUV transparency of multicomponent aluminium fluoroberyllate glasses from the view point of their compositional dependencies. The purpose of this paper is to prepare deep VUV transmitting optical materials and determine the optimum glass compositions for aluminium fluoroberyllate glasses investigating their thermal stabilization against crystallization."

Jan 1, 2000

By Miaoyong Zhu, Sen Luo

"A two-dimensional CAFD model was developed for simulating the solute diffusion-controlled dentritic growth in the low Peclet number regime. Mass conservation and local equilibrium at the solid/liquid interface were solved to determine the growth velocity of interface with consideration of constitutional and curvature undercooling. The modified decentered square growth proposed by Wang et al was adopted to capture the first eight neighboring cells. The comparison between the classic Lipton-Glicksman-Kurz (LGK) analytical model for steady state tip variables and the simulated values showed that the present model was capable of quantitatively determining the dendritic growth, and the simulation tests demonstrated that the effects of the mesh anisotropy in growth kinetics and crystallographic orientation were eliminated. The numerical simulations were performed to the dendritic growth ofFe-0.6%C binary alloy in undercooled melt, and the results showed that the present model could predict the dendrite morphology with artificial growth orientation in acceptable level.IntroductionDuring the solidification of metals and alloys, the dendrite grows from the substance or the undercooling melt and solute redistributes between the dendrite and the interdendritic liquid. The solidification microstructure is close related to the phase and solute evenness and has a close linkage with the properties of final production.In the past few decades, various kinds of deterministic and stochastic models have been developed to predict the evolution of microstructures in solidification, with the fast development of computer power. Among these methods, Phase Field (PF) model [1, 2] has been known as one of the most adequate deterministic models for directly simulating the dendritic growth. However, there is a vital drawback that the PF method requires considerable computation time and is limited to simulate very small domains with a few dendrites [3]. On the other hand, stochastic models, such as Monte Carlo (MC) method [4, 5] and Cellular Automaton (CA) method [6-8], have been usually applied to predict the solidification microstructure evolution. Comparing with the MC method, the dendritic growth kinetics is explicitly integrated in the CA model, while the MC model doesn't. Therefore, the CA method is more reasonable to predict the dendritic growth during the solidification of melt."

Jan 1, 2013

By J. M. D. Wilson

An analytical program using a combination of SEM-based image analysis techniques is developed for automated modal analysis of ores containing silicate and other gangue minerals. Previous knowledge, gathered by means of either optical microscopy, X-ray diffraction, SEM, or electron microprobe analysis is used to establish discrimination criteria in the image analysis program. The program initially discriminates minerals on the basis of their relative grey values in a backscattered electron image. For those minerals which have overlapping grey levels the minerals are identified by the program using energy dispersive X-ray spectrometry with X-ray counting for twelve or more elements. This technique is useful to quantify ores in which the gangue minerals are numerous. Two cases of application are presented.

Jan 1, 1999

By Junji Shibata

Some fundamental studies were carried out in order to produce composite powders comprising of two or three metal salts by using liquid-liquid extraction and to develop the control technology of the particle size. The combination of samarium and cobalt was selected as the two component composite powders. Both stripping and crystallization occurred at the same time by emulsifying the organic phase loading the two metals extracted with Versa tic Acid 10 and the aqueous solution containing oxalic acid. The effect of aqueous pH, oxalic acid concentration and agitation speed was examined on some properties such as crystallization percent, particle size and shape of each metal oxalate powders obtained in this process. The analysis by using EDX showed that the two metal oxalates were distributed uniformly at the same ratio as the organic phase composition.

Jan 1, 2001

By J. B. Vander Sande, I. G. Solórzano, B. S. You, P. M. Jardim, W. W. Park

"Alloys with six different compositions in the system Mg-Ca-Zn were produced by melt spinning. The aging behavior of alloys was investigated by measuring the changes in microhardness after isochronal aging and the microstructure was analyzed by means of transmission electron microscopy (TEM), energy dispersive X-ray spectrometry (EDS), scanning transmission electron microscopy (STEM) and scanning electron microscopy (SEM). All six compositions in the as-solidified condition show a difference in microstructure between the wheel contact side (zone A) and the free surface side (zone B) as a result of the differences in the solidification rate across the ribbons. One of the alloys (Mg-l.5wt%Ca-6wt%Zn) was chosen to be more deeply investigated in this work as it exhibited grain boundary films and an age hardening behavior was produced in that alloy.IntroductionMagnesium is the lightest of all the commonly used metals, and very attractive for applications in transportation. It also has a number of other desirable features, including good ductility, better damping characteristics than aluminum, and excellent castability. However, there are some negative features, such as high reactivity in the molten state, inferior fatigue and creep resistance as compared to aluminum, poor corrosion resistance and high production cost.In recent years there has been a significant increase in magnesium use as a structural material. These structural applications include aerospace, automotive and nuclear industries as well as appliances and sporting goods (1 ). According to reports on Mg-Zn alloys, the addition of Zn (2) in magnesium increased strength. Also, since the maximum solubility of Zn in magnesium is 6.2wt%, a considerable amount of Zn can be retained in solid solution in magnesium alloys by rapid solidification. In addition, Ca is known (3) to be one of the most potent alloying elements for refining the microstructure and precipitates in magnesium alloys, and also to improve mechanical strength and corrosion resistance."

Jan 1, 2000

By Pascal Gardin

The purpose of the paper is the mathematical modelling of flows inside steel continuous casting mould. For CFD validation of flow oscillation prediction, unsteady calculations with a realizable k- model were performed in a billet caster with rectangular section. Self sustained and regular oscillations were obtained. Calculated flapping frequency is very close to what is mentioned in literature. For slab caster configuration, flow oscillation is influenced both by lower roll, which creates very small frequency oscillation (0.012 Hz for our water model), and upper roll, which creates slightly higher frequency oscillation (0.05 Hz). The two rolls interact and it is possible to detect both frequencies in the nozzle jet region. Numerical results are in good agreement with measurements for fluctuating velocity spectra and provide explanation for interaction of rolls. To improve flow stability inside the mould, it is established that gas injection in the nozzle has a very positive effect.

Jan 1, 2006