Search Documents

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By Shadia J. Ikhmayies

"Cadmium sulfide (CdS) in the form of thin films is an interesting material because it has a large variety of applications ranging from photovoltaic to luminescent devices. N-type CdS is usually used as a window layer in the heterojunction CdS/CdTe thin film solar cells. A review of the photoluminescence (PL) spectra ofn-type CdS thin films prepared by different techniques was performed. The effects of different dopants and impurities and the effects of temperature and deposition parameters on the PL spectra were discussed. Annealing in different atmospheres causes the changes in material structure and phase change from cubic to hexagonal phase which can be detected through the variations in the PL spectra. CdCh heat treatment improves the cystallinity of the films and enhances the exciton peaks and the green band in the PL spectra.IntroductionThin CdS films deserve attention because their expected gap emission lies very close to the highest sensitivity of the human eye. Thus, one might assume that thin CdS films are an appealing host for photonic devices [ l]. They have been used in a lot of applications including electronic and optoelectronic devices [2]. Thin films ofn-type CdS are widely used as a window layer in heterojunction solar cells such as CdS/CdTe solar cells. Doped and undoped CdS thin films can be obtained by different techniques such as; spray pyrolysis (SP) [3], chemical bath deposition (CBD) [2, 4], pulsed laser deposition [5, 6, 7], laser ablation [l], thermal evaporation [8].Several experimental techniques have been used in order to study semiconductor defects. In particular, photoluminescence (PL) has been shown as a powerful and sensitive tool in examining the crystal quality of polycrystalline thin films. PL can be used in the detection of defects which are radiative active. These defects can also act as traps in the transport of carriers [9]. The photoluminescence (PL) of thin film CdS is strongly influenced by the unbalanced stoichiometry, which is typical for CdS and is in general evoked by a Cd surplus. With increasing Cd content, the emission spectra move far below the gap to the red spectral range. Besides stoichiometry problems, independent of the material deposited, the PL properties of thin films depend on surface features and the influence of the interface between the film material and the substrate [10]."

Jan 1, 2013

By D. F. Liub, Z. Y. Liu, W. Y. Xue, Y. F. Shenb, Y. D. Wang

"The microstructure characteristics and deformation behavior of ultrafme grained (UFO) 304SS fabricated by accumulative rolling and armealing have been investigated by means of tensile tests, electron-backscatter-diffraction (EBSD) and transmission electron microscopy (TEM) techniques. The volume fraction of martensite phase decreases with increasing armealing temperature. In the grain sizes ranging from 300 nm to 10 µm, the strength held Hall-Petch relationship. The sample with an average grain size of 300 nm exhibited extra high yield strength of 1700 MPa and a tensile strength of 1780 MPa, while the elongation retains 12%. The limited uniform elongation in the UFO materials could be explained in terms of plastic instability. Very interestingly, for the bulk material with an average grain size of 1.200 µm, the high yield strength and uniform elongation were simultaneously achieved to be as 1000 MPa and 18%, respectively.IntroductionUltra-high strengths have been achieved in elemental metals by employing heavy plastic deformation, or by creating ultra-fine-grained (UFO) structure. Here UFO materials are defined as polycrystalline solids with property-controlling microstructural features below the 1 µm level. Typical processing routes include severe plastic deformation (SPD) [1, 2], which decomposes the grains through dislocation accumulation and reorganization (polygonization). Several different kinds of SPD process for bulk materials are typically as equal-charmel angular pressing (ECAP) [3], high-pressure torsion (HPT) [4] and accumulative roll-bonding (ARB) [5]. One of the main motivations for such a push for the very small grain sizes stems from the expectation of unprecedented mechanical strength, as predicted by the well-known Hall-Petch relationship that projects a continuous rise of strength with decreasing grain size [6]. However, these ultra-high strength metals no longer have the high ductility typical of their conventional coarse-grained counterparts, because the undesirable inhomogeneous deformation on the microstructure level can lead to the early onset of failure, severely limiting the useful ductility [2]. Recently, the interesting strategies have been performed to increasing simultaneously the ductility and strength ofUFG pure copper and nanostructured alloys by Zhao et al [7, 8]. In a pure copper, a high ductility has been achieved without sacrificing strength by introducing a high density of pre-existing twins and a large fraction of high-angle grain boundaries. Their encouraging results trigger our motivation to obtain high strength and ductility from the commercially bulk material."

Jan 1, 2013

By Riyad N. Ahmad-Bita, Shadia J. Ikhmayies

"SnO2:F/CdS:In structures were prepared by the spray pyrolysis technique on glass substrates at a substrate temperature Ts = 450°C. NH4F and HF were both tried as the sources of fluorine in the precursor solution of SnO2:F. A comparison between the properties of structures obtained by using the two doping compounds was performed. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to characterize the films. The structures prepared by using HF as a fluorine source were found to have more ordered crystal growth, larger grain size and sharper absorption edge. From the inspection of the first derivative of the absorbance it is expected that more interdiffusion on the SnO2:F/CdS:In interface takes place in the structures made by using HF. These results confirm that these films are better as forecontacts for CdS/CdTe solar cells.IntroductionThin film CdS/CdTe solar cells built in the superstrate geometry rely on transparent conducting oxides (TCOs) to make the front contact The investigation of combined CdS-TCO films has recently been developed owing to the great interest of better understanding the effect of these bilayers on the absorbers [1]. Usually SnO2 is utilized as a front contact for these solar cells. Optimizing the properties of the SnO2/CdS structures is an important step on the way to get high performance CdS/CdTe solar cells.There are different methods to prepare SnOz thin films, such as reactive sputtering [2], evaporation [3], chemical vapour deposition [3, 4], dip coating [5] and spray pyrolysis [6-9]. At the same time CdS thin films can be prepared by different techniques such as chemical bath deposition [10], thermal evaporation [11], screen printing [12] and spray pyrolysis [7, 13]. However, the spray pyrolysis technique is a very low cost and simple technique that enables intentional doping and getting large area and uniform thin films [14]. For these reasons it is choused to prepare SnOz and CdS thin films in this work. To improve the properties of these compound semiconductors, SnOz was doped with fluorine and CdS was doped with indium where such doping is well known for these compounds."

Jan 1, 2012

By Jari Aromaa, Antti Kekki, Olof Forsén

"The deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential depends on surface morphology, surface film resistance and additives on cathode surface. The effects of surface properties on copper nucleation and growth rates were studied for used stainless steel blanks from several tankhouses. The surfaces of the blanks were characterized with electrochemical and mechanical methods. Electrochemical deposition tests were done at current density of 300 A/m2 for 10, 30 and 60 seconds. The nucleation density and copper coverage were estimated using image analysis. The surface film resistance did not correlate with copper growth. Increasing surface roughness correlated with lower copper growth.IntroductionStainless steel cathode blanks in copper electrorefming are usually made of AISI 3 I6L type steel. They have a typical lifetime over 10 years. During use the surface will collect deposits and become rough due to wear and corrosion. These factors can affect the nucleation and growth of copper. The nucleation and deposition of copper on inert substrate depends on the number of active sites that will react at certain overpotential. The critical overpotential can depend on surface film resistance, surface morphology, and additives adsorbed on cathode surface.The deposition potential of metallic ions on a foreign substrate is usually higher than the deposition potential on the electrode made of the same metal due to crystallographic substrate/metal misfit [I]. If the substrate has traces of the depositing metal they will be preferential growth sites. For a smooth deposit a large number of simultaneous nuclei is necessary. However, excessive nucleation density can lead to porous deposits [2]. Surface films of good conductivity are needed for dense nucleation and small nuclei. On cathode blanks the number of active sites increases with increasing surface film conductivity [3-5] and/or surface film porosity [6]. On AISI 3 I6 L stainless steel a more resistive oxide has been found to limit favourable sites for copper nucleation and more conductive film promoted high-density copper nucleation [7]. Also Urda-Kiel et al. have concluded that thicker oxide layers on AISI 304 stainless steel resulted in lower nucleation [8]. Increase in overpotential or current density activates more and more of the potential nucleation sites and this can be seen as higher number of nuclei [9] or smaller average distance between nuclei [10]."

Jan 1, 2012

By Jamil M. Khalifeh, Shadia J. Ikhmayies, Bothina A. Hamad

"We computed the optical properties of the cubic niobium nitride (o-NbN) compound using the full potential linearized augmented plane wave (FL-LAPW) method within density functional theory (DFT). The complex dielectric function and optical constants, such as optical absorption coefficient, refractive index, extinction coefficient, energy-loss spectrum, and reflectivity, are all calculated and compared with experimental results. The behavior of the computed quantities is similar to that obtained experimentally, but the optical positions are shifted to lower energies. This shift was related to the strong interband transitions, which are located at energies higher than 5 eV for NbN- as they are for IV B transition-metal mononitrides- and they appear in the computed spectra and not in the experimental spectra. These interband transitions simply shift the position of the reflectivity edge or the screened plasma frequency to the longer wavelength side.IntroductionIn recent years, NbN, as a transition metal nitride, has become a very popular material due to its high hardness, melting point, wear resistance, chemical inertness and temperature stability, which makes it suitable for use as emission cathodes in microelectronics and sensors, optical films and micro-mechanics etc [l]. Niobium nitride has long been known as highly polymorphic material, for which several crystalline structures have been reported in the literature [2]. These structures include the well known super-conducting rock-salt (Fm-3m, or Bl) structure (o-NbN), the hexagonal structure with space group p63/mmc and prototype Fe2N (18fuN), the hexagonalstructure with space group p63/mmc and prototype NiAs ~-NbN) and others.There has been a lot of computational studies for the structural and electronic properties ofNbN [3, 4-7], but according to our knowledge there is not any computational work that has been devoted to study the optical properties of this transition metal compound. At the same time a number of authors had performed experimental work in this direction. For example, Xin-kang et. al [l] studied the microstructure and optical properties of magnetron sputtered NbN thin films. Torche et. al [8] studied the composition, structure, electrical and optical properties of nonstoichiometric niobium nitrides. Newport et. al [9] investigated the reflection and transmission spectra of cubic niobium nitride films, and Tanabe et. al [10] had investigated the optical parameters and reflectivity of reactively sputtered NbN thin films by using in situ ellipsometry."

Jan 1, 2013

By James B. Pfeiffer

TETRA Technologies, Inc., has applied its HDSIM metals precipitation system to treat a waste stream containing scrubber blowdown and process water from a smelter operation. The combined stream contained cadmium, lead, selenium, arsenic and zinc, plus some iron and copper. Treatment requirements included meeting stringent mass flow limitations for specific heavy metals. The HDS ? system can reduce the arsenic from 600 ppm to less than one ppm. The process generates a dense sludge that can be reprocessed in a smelter, eliminating the liability associated with landfilling. Flow diagrams and process details are discussed.

Jan 1, 1994

By P. Gray

Process and engineering development of the Warner Zinc Process over the past two decades has proceeded alongside the world-wide collection and analysis of operating and cost data of current processing practices from sulphide ores to refined metals. Study of these data shows that recoveries are dependent on mineralogical characteristics of the sulphide matrix and point to the inadequacy of differential flotation as a tool for preparing feed for smelters. The paid-for return at the mine on the combined metal values in zinc rich sulphide ores rarely exceeds 80% and increasingly runs as low as 50-60%. Surveying the possible alternative ways of improving these performances leads to the conclusion that the Warner Process is the only technology in sight that could meet a target of 90% paid-for recovery and that its development has now reached a point where it can be a fully practicable process for all mixed sulphide ores.

Jan 1, 2000

By Robert P. Stevens

It is important for a refractory supplier to make systematic petro-graphic examinations of products which have been in service in the furnaces and kilns of customers. The petrographic examination of refractory service samples involves the microscopic study of polished and/or thin sections, supplemented by electron probe microanalysis, as well as the bulk chemical and XRD analysis of zones in the samples. The evolution of the A. P. Green Refractories Company petrographic laboratory is described, and the application of petrographic methods is illustrated in the examination of service refractories from a Portland cement rotary kiln and an AOD stainless steel vessel. The objectives of such studies are to assist the customer in the solution of his refractory problems, and to accumulate data which are of use in the design of improved refractory products.

Jan 1, 1981

By Ayşe Ece Yıldızçelik, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg was used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques.

Jan 1, 2015

By E. B. Zanelato

The process of casting metals and alloys occurs through the fusion of this metal and its subsequent casting into a mold with the dimensions and geometry close to the final piece. Most foundries use sand casting molds for making you. This work aims to characterize and evaluate the foundry sand to allow its use in segments of Civil Engineering, creating a viable destination for a residue is that discarded. The following characterization tests were performer: particle size, chemical analysis, X-ray Diffraction and Density Real grain. For the execution of the test specimens was used to 1:3 cement and sand, and the incorporation of 10% and 20% of the total mass replacing the sand, and the trace reference. The results show that best results in compression and bending tests were obtained by replacing 10 % of common sand for sand casting.

Jan 1, 2015

By Sedef Pinar Basag, Onuralp Yucel, Ahmet Turan

Niederschlag process is commonly used to produce metallic antimony. The process is a metallothermic process which is conducted in one step for metallic antimony production. Using this method Sb2S3 is mixed with coal and metallic iron and subjected to reduction. During heating, antimony sulfide is decomposed and sulphur combines with iron to form the matte phase. Metallic antimony is collected at the bottom of the crucible. In this study, evaluation of Sb2S3 concentrate, extracted and obtained from West Anatolian Region of Turkey was investigated by using Niederschlag process. The reductant stoichiometry, reduction temperature and duration were carried out in the experiments. Chemical analysis methods by using atomic absorption spectrometry (AAS) and X-ray diffraction spectrometry (XRD) techniques were used for the characterization of the concentrate, metallic nuggets and matte phases.

Jan 1, 2016

By Hua-qing Li

Electromagnetic stirring process effectively improves the casting quality of metals. In this paper, the physical simulation experiment, in which the molten copper is displaced by mercury, was designed. The factory test parameters were determined according the simulated data. The flow behavior of the mercury to be stirred as well as the relations between the microstructure of plate blanks and the current parameters were analyzed. With an appropriate electromagnetic stirring, the inverse segregation of tin for C51900 alloy plant blank reduces from 15 % ~ 30 % to about 5 %, and the proportion of equiaxed grain rises to larger than 30%.

Jan 1, 2009

By Dong Liang, Honggang Zhong, Zhenxing Yin, Qijie Zhai

"2507 super duplex stainless steel (SDSS) has been widely applied in a marine environment, attributing to its excellent pitting corrosion resistance and mechanical properties which are particularly determined by the nitrogen precipitation behaviors and volume fraction of ferrite. In this paper, various cooling rates were obtained by applying four different moulds with the common gating system. By which the influence of cooling rates on nitrogen precipitation behaviors and the ferrite fraction in cast 2507 SDSS was comparatively investigated. The results showed that nitrogen porosity could easily precipitate in cast 2507 SDSS under standard atmospheric pressure. The number of nitrogen holes increased with decreasing the cooling rates, and the holes mainly distributed in three zones, i.e. the interface between the horizontal and vertical columnar grains, top vertical columnar grains and the final solidification region. Additionally, higher ferrite fraction was obtained with lower cooling rates.IntroductionDuplex stainless steels (DSS) have a dual-phase microstructure consisting of ferrite (d) and aus-tenite (?). Due to the combined advantageous properties of d and ? phase, their application rapid-ly increased in industry [1, 2]. Super duplex Stainless Steel (SDSS) is the third generation of du-plex stainless steels, of which the alloy elements Cr, Ni and N content are higher than the stand-ard 2205 DSS. Because it has high contents of alloy elements, the SDSS has better mechanical properties, and its pitting resistance equivalent number (PREN) reached a point 43. Hence SDSS has been used in petroleum chemical industry, the marine equipment and harsh corrosion environments [3]. SDSS contains ferrite stabilizing elements, such as Cr, Mo and Si, and austenite stabilizing elements like Ni, Mn and N [4]. Many researchers have studied the effects of these elements on the stabilization of d and ? phase and the ratio of the two phases. High nitrogen con-tent is another prominent feature of SDSS. Nitrogen addition to SDSS is very effective for improving its mechanical properties [5] and corrosion resistance [6], such as pitting resistance in NOx environment. To increase the nitrogen content in steels, a lot of work had been done. N. Nakamura and S. Takaki [7] examined the behavior of nitrogen absorption in Fe-23Cr alloy powder by sintering in nitrogen gas atmosphere, they found nitrogen content easily up to 1.0 wt. %. Using devised NH3 gas injection system, W. Park et al. [8] successfully produced austenitic Fe–23.5Cr alloys containing over 3 wt. % of nitrogen. Further-more, W.P. Tong et al. [9] stated that nitrogen percent was extraordinary high (about 10 wt. %) in pure iron plate. However, the above methods are difficult to be applied to large-scale industrial production."

Jan 1, 2012

By Zhenyang Wang, Xingle Liu, Xiangdong Xing, Shan Ren, Hongen Xie, Jianliang Zhang

"Non-isothermal combustion experiments of different additive amount of bituminous (0, 20, 40, 60, 80, 100 wt%) were conducted by synthesized thermogravimetry analyzer(STA409PC) from room temperature to 900°C in air. The changes of combustion characteristic parameters o f pulverized coals in different atmospheres are analyzed. The results show that DTG curves of coal combustion move to low temperature zones when the amount of bituminous increases. It indicates that both ignition and burnout temperature are lower, burnout time decreases, combustion characteristic index obviously increases, and combustion performance of blending coal are improved. The iso-conversional method involving Kissinger-Akah-Sunose (KAS) method was used for the kinetic analysis of the main combustion process. The results indicated that, when the additive amount of bituminous varied from 0 to 100 wt%, the value of activation energy which would sharply reduce if the additive amount of bituminous was under 60% increased from 133.94 kJ•mol-1 to 78.03 kJ•mol-1by using KAS method.IntroductionPulverized coal injection (PCI) to blast furnace (BF) is an important way for saving energy and reducing resource consumption during the ironmaking process. In order to acquire higher coal injection quantity, the relevant research topics in the field of pulverized coal combustion technology such as enhancing the efficiency of pulverized coal combustion, improving the combustion characteristics and reducing the harmful gas emissions and so on received extensive attention in recent years [1,2]. The combustion of blending coal when the appropriate proportion is selected for coal and also mixed well- distributed could give full play to the advantages of various types to make up the defects of single coal which is widely used throughout the world. So the blending coal injection to BF could produce a good impact on safety and economy for productive process. Therefore, a large amount of experimental researches on the combustion characteristic of blending coal for anthracite and bituminous were carried out by experts and scholars around the world [2-7].Nevertheless, the systematic research on the combustion behavior of anthracite with different content of bitumite in a thermogravimetric analyzer (TGA) is less. So in this paper, using the method of multiple scanning rate of conversion method, bituminous to promote the pulverized coal combustion reaction was studied to analyze its promotion mechanism of pulverized coal combustion reaction process, and the kinetic parameters of activation energy was also calculated, which to provide theoretical basis for the rationalization of resource utilization."

Jan 1, 2014

By Denise C. R. Espinosa

Rechargeable lithium batteries are one of the most promISIng technology in battery development. Although Li ion batteries have been used as an alternative to the more polluting and less performing Ni-Cd batteries, Li ion batteries have limited life and their disposal is uncertain. It is imperative that valuables from wastes, such as lithium, should be recovered. The main objective of the present work was to characterize secondary lithium batteries for cellular phones. This was done using unit operations of mining processing, x-ray diffraction (XRD), chemical analyses and the rmogravimetric analysis (TG). The unit operations were hammer mill grinding, knife mill grinding, size separation and magnetic separation. After the hammer grinding process, the plastic cases were almost intact, however, they have released the cylindrical lithium batteries themselves and these parts correspond to 70% of the total battery weight.

Jan 1, 2001

By Isıl Kerti, Sibel Daglılar, Sinem Yıldırım

In this study, effect of rolling and coiling temperature in thermo mechanical controlled process (TMCP), on the microstructure and mechanical properties of dual phase (DP) steel according to martensite volume fraction (MVF) rate was investigated. By using various finishing mill exit temperature and cooling conditions that is controlled laminar cooling system, the microstructural evolution of coil improves the mechanical properties with lower costs and higher productivities, in comparison to the heat treatment after rolling. The main part of the paper contains the result of tensile, yield and microstructure properties of DP600 steel produced on hot strip rolling plant and run- out table line. The results show that a higher MVF and an increasing cooling rate after the last deformation raised strength of the DP600 steel. The yield strength and ultimate tensile strength increase by decreasing coiling temperature.

Jan 1, 2015

By I. B. Scorzelli

The aim of this paper is to make a detailed mineralogical characterization of a typical brazilian xenotime and zircon from the Pitinga Mine using SEMIEDS techniques, On the other hand, superficial pretreatments with HCI, HN03 and HF were done to evaluate the modifications on surface compositions and the morphology of the particles for flotation purposes, The studies showed that both xenotime and zircon present very small inclusions of thorite; zircon is strongly metamictizated given rise to malacon. The HF pretreatment deeply affected the morphology of the particles as well as the surface properties in relation to flotation.

Jan 1, 1996

By A. V. Tarasov, A. D. Besser

A processing flowsheet has been developed for treating substandard lead-containing polymetallic bulk concentrates and intermediate flotation products containing precious metals, which comprises oxidizing roasting in a calcination kiln and electrothermic smelting generating low volumes of off-gas. The proposed flowsheet also incorporates a dust collection system and sulfur dioxide recovery from off-gas. It is proposed to implement this process by using a reaction smelting technique. For this purpose, the charge to be fed to the smelting furnace after its calcination in a drum-type rotary kiln must have a ratio of sulfide sulfur to sulfate sulfur of at least 1 :2. Electric smelting makes it possible to produce lead bullion that also collects the precious metals contained in the feed, as well as copper-lead matte and slag containing zinc. The recovery of lead into lead bullion and into matte is approximately 83% and 14%, respectively (thus the overall recovery is 97%); the total recovery of gold and silver into lead bullion and matte is 98%; th\lt of copper into matte is 89%; the recovery of zinc into slag is 96%; and that of sulfur into sulfuric acid or gypsum is 90%. After the recovery of zinc from slag, the latter can be utilized in the construction industry.

Jan 1, 2000

By Sne?ana Devi

Mineralogy is a significant scientific discipline, essential in establishing the nature and the character of raw materials, regardless of whether they are monomineral or polymineral. Mineralogical characterization is very important, because its results give valuable information on features and nature of examined materials. Information's on mineralogical nature of mineral raw materials influence directly the quality assessment of a raw material, and thus the possibility of its use. The possibility of use of mineralogy in different industrial branches confirms constant activity of this scientific discipline. By use of methods within mineralogical analysis (optical microscopy, x-ray diffraction and others) data on mineral raw materials can be obtained as support in mineral raw materials quality assessment. Short description of results of mineralogical analysis of some mineral materials (granodiorite, dolomites, clay, refractory materials, slags and casting powders) in this paper shows the importance of its support to quality assessment and determine the possibilities of their use.

Jan 1, 2009