Search Documents

By L. E. Kun, R. O. Oelofsen, E. J. J. van Vuuren

High-rate floc-blanket clarification of gold pregnant rotary filtrate was introduced at the Vaal Reefs South gold plant of the Anglo American Corporation during February 1978. A. daily 12 000 to 15 000 t of filtrate, with an average suspended-solids concentration of 350 mg/I, is continuously clarified to a concentration of less than 2S mg/I of suspended solids in a modified plant pachuca (10 m in diameter) at throughput rates of 7,7 to 8,5 ma/m2.h by the addition of 5 g/t of ferric chloride inorganic coagulant and 0,2 g/t of Superfloc NI00 flocculant. The pachuca overflow is then clarified further in seven Stellar candle pressure filters of 54,S m2 surface area to under 5 mg/I of suspended solids. The combined clarification cost when the hopper clarifier is used in conjunction with the Stellar filters is R0,0032 per ton of liquid treated, which is approximately 60 per cent lower than the cost of Stellar filtration on its own. The savings are mainly due to the reduced use of filter pre-coat, the consumption of which has dropped by 70 per cent since the introduction of hopper clarification.

Jan 1, 1979

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

By M. J. Santofimia

Multiphase microstructures in steel have been intensively studied in the past years, but combining non-equilibrium phases still offers a great potential for further development of these steel grades. Thus, improved combinations of mechanical properties can be obtained with microstructures formed by bainite or martensite, in combination with retained austenite. In particular, microstructures on the basis of carbon-depleted martensite and retained austenite can be produced by the very promising production process named quenching and partitioning (Q&P). Originally, the Q&P process aimed to avoid the formation of bainite during the heat treatment. However, the process does provide the possibility for (carbide-free) bainite formation during the partitioning step, i.e. in the presence of martensite. This article evaluates this approach, considering thatthe formation of bainite from austenite is strongly influenced by the preceding formation of martensite. Although the accelerating effect of the presence of martensite during bainite formation has been observed, it is not yet fully understood, and experimental and theoretical studies are being performed in order to come to a more effective exploitation of these processes for the formation of multiphase microstructures.

Jan 1, 2013

By A. Montini, M. H. Moys

A technique for the measurement of slurry consistency inside a grinding mil is described. The rate of slurry drainage from a sensing probe mounted through the mil shell is measured and correlated with the percentage solids of the slurry discharging from the mil. The response time of the measurement(obtained on a pilot bal mil) is compared with the response time of the viscosity of the mill discharge. It is shown that the new measurement should allow much tighter control of the mil behaviour, with concomitant savings in the consumption of power and steel.

Jan 1, 1988

By A. M. Thyer

Throughout the history of mining, underground fires or explosions have killed many hundreds or thousands of people. Fortunately, the safety record has gradually improved as a result of many people’s work on improving safety standards and work practices. However, fire and explosion still remains a threat in many situations. As a result the UK Mines Inspectorate commissioned a project to study materials used underground and to develop a fire/explosion risk assessment system. Such a system has been developed, following the study of incidents, specified fire resistance criteria, and fire safety practices. The final methodology uses a series of check sheets to identify potential fuels and ignition sources, preventative measures, fire/explosion mitigation systems, and items for inclusion in emergency plans.

Jan 1, 2003

By A. García-Gutiérrez, A. Aragón-Jerónimo, R. Salazar-Mendoza

A theoretical analysis of a two-region solid-liquid flow system in horizontal pipes is presented, which considers a stationary bed of drill cuttings as a porous medium (-region) below of a two-phase dispersed flow (-region).The method of volume averaging was applied in this study to derive a rigorous mathematical model in which each variable is precisely defined. This model includes the volume-averaged transport equations for both the two-phase dispersed flow and the porous medium regions and terms from a macroscopic forces balance. The solution of the two-region model allowed evaluation of the behaviour of pressure gradient as a function of velocity, total volume fraction of cuttings and the relationship of the height of the stationary bed and pipe diameter. The solution is based on a backward finite difference explicit scheme. The simulated physical system is a pipe of 4.135 m in horizontal length and 0.0508 m in diameter. A one-dimensional, mesh-centred grid, consisting of 100 nodes, is used. The numerical results were compared with experimental data on slurry flows and a good agreement was found. Keywords: two-phase, cuttings transport, solid-liquid flow, drilling modelling, volume averaging.

Jan 1, 2007

By W. A. Te Riele

The National Institute for Metallurgy was the venue for a one-day colloquium on 'The Chemistry of Processes for the Recovery of Gold on Activated Carbon'. Organized by the South African Chemical Institute (Southern Transvaal Section) in collaboration with the National Institute for Metallurgy (NIM) and the South African Institute of Mining and Metallurgy, the colloquium attracted tremendous interest from the mining industry. Some 300 metallurgists, engineers, and chemists were brought up to date on advances in this technology made by scientists of NIM and the Anglo American Research Laboratories (AARL).

Jan 1, 1980

By C. -I. Lee

Since the early 1970s, Korea has constructed many large-scale tunnels and underground storage caverns in response to the rapid industrial development. The rock mechanics engineers have accumulated valuable experiences in the area of underground space technologies. But they still face technical challenges in environmental and safety aspects. To discuss those challenges in Korea, a brief engineering description of underground space projects including oil and gas storage, food storage, pumped storage power plant, transportation tunnels, waterway tunnels, and radioactive waste disposal is presented. Mechanical and hydrological stability analyses of the storage caverns in Korea are also introduced. Depuis le début des années soixante-dix, le développement industriel rapide en Corée a entraîné la construction de nombreuses galeries et cavernes de stockage souterraines. Les ingénieurs de mécanique minière ont donc accumulé des expériences précieuses dans le domaine de la technologie de l’espace souterrain. Cependant, ils font toujours face à de nombreux défis techniques en ce qui concerne les aspects de l’environnement et de la sécurité. Pour présenter ces défis en Corée, l’étude présente décrit les projets d’espace souterrain, y compris le stockage de pétrole et de gaz, de nourriture, centrales de stockage pompé, tunnels de transport, tunnels navigables, et évacuation des déchets radioactifs. Des analyses de stabilité mécanique et hydrologique des cavernes de stockage en Corée sont aussi présentées. Seit Anfang der 70er-Jahre, baute Korea in Folge raschen Industriewachstums viele lange Tunnelsund unterirdische Lagerungsräume. Fachkräfte im Bereich Gesteinsmechanik sammeltenwertvolle Erfahrungen über unterirdische Raumtechnologien. Dennoch stehen sie auch heute nochvor technischen Herausforderungen im Bereich Umweltschutz und Sicherheit. Zur Erläuterungdieser Herausforderungen in Korea folgt eine kurze technische Beschreibung der Projekte zurSchaffung unterirdischen Raumes für beispielsweise Öl- und Gaslagerung,Nahrungsmittellagerung, Pumpspeicherwerke, Straßen- und Wasserstraßentunnels, als auchLagerung radioaktiven Mülls. Mechanische und hydrologische Stabilitätsanalysen derLagerungsräume in Korea werden ebenfalls dargestellt.

Jan 1, 2003

By F. L. D. Cloete

he above article by E. Barnea, which appeared in the January 1978 issue of the Journal (vol. 78, no. 6, pp. 143-145), calls for comment in view of the author's claims for the novelty of his proof. He states in his article that its main purpose is to give a mathematically acceptable proof by induction of the 'recently proposed' equation

Jan 1, 1978

By A. J. Van Rensburg, N. B. Strydom, C. H. Van Graan

The design, construction, and use of a practical ice-jacket for miners by N. B. STRYDOM, Ph.D. (Illinois) (Fellow), D. MITCHELL, Ph.D. (Rand) (Member), A. J. VAN RENSBURG, M.Sc (Poteh) (Visitor), and C. H. VAN GRAAN, M.Sc (Pretoria) (Visitor) Microclimate suits have been shown to be very effective in decreasing physiological strain in hot, wet environments, thus enabling men to work without risk in areas that would normally carry a high risk of heat stroke. In this paper, some design considerations in the development of the frozen jacket are described. Water complied with most of the desirable properties required of a coolant material for use In a microclimate suit. The Human Sciences Laboratory has developed a jacket in which ice is used as the coolant and which is designed according to the most acceptable anthropometrical characteristics. The jacket consists of an inner poncho-type waistcoat containing 28 water compartments. Over this is worn an insulating jacket, which minimizes warming of the coolant by the environment. Suitable refrigeration units have been developed to freeze the jackets underground. Laboratory tests have shown that these jackets are effective for about 2,5 hours, Irrespective of the wet-bulb environment, when men are working at a moderate rate. Jackets should, however, be used only in environments in which the wet-bulb temperature is in the range of 32,S0 to 35,S °C.

Jan 9, 1974

By F. Q. P. Leiding

SYNOPSIS A technique is described for measuring the change in volume in a borehole drilled in a rock mass subjected to stress and strain. It is shown that the volumetric strain or change in volume provides a practical estimate of the the stress in the rock.

A description is given of a simple, cheap device that enables the intact shear strength of rock to be determined quickly and inexpensively. Thin rock plates, prepared with a diamond saw, are tested in double shear by a linear punching action. By varying the direction of the diamond-saw cut in a number of specimens, the change in shear strength can be measured for different orientations relative to the rock fabric.

Jan 1, 1980

By P. A. Laxen, P. J. van Staden

Alternative procedures for the recovery of gold from old sand dumps are discussed, with emphasis on the use of heap leaching. The modification of material to improve its permeability prior to heap leaching is not currently receiving much attention in South Africa. The channeling of solutions through heaps and the high consumption of reagents sometimes ascribed to heap leaching can, as shown by the results described in this paper, be lessened by desliming of the sand prior to heap leaching and the treatment of the resulting slimes fraction by agitation leaching and carbon-in-pulp. This combined procedure results in a higher overal recovery of gold. Alternatively, the sand can be heap-leached as it is after agglomeration with lime and cement, which improves the mixing and neutralization of the material, as well as lessening the probability of channeling.

Jan 1, 1988

By A. J. S. Benade, A. J. A. Heyns, N. B. Strydom

The maximum oxygen intakes of samples of about 30 Bantu, weighing less than 50 kg from different tribal groups (Zulu, Xhosa, Sotho and Shangaan) were measured on a treadmill. The mean maximum oxygen intake of the 164 men was 2,12 litresjmin and only 18 men (11 per cent of the sample) had maximum oxygen intakes of 2,5 litres/min or above (the minimum requirement for such tasks as shovelling rocks and tramming it). The samples of the different tribes differ in age, but when the age effect is taken into account then there were no significant differences between tribes in maximum oxygen intakes. An incidental finding was that both age and body weight correlated significantly with the maximum oxygen intakes of these underweight subjects. Not one of the subjects who weighed less than 45 kg or who was older than 40 years had maximum oxygen intakes high enough to permit their being able to do strenuous work underground. It is clear therefore that Bantu who weigh less than 45 kg or are older than 40 years should not be employed on such strenuous tasks as shovelling rock and tramming it.

By P. S. Turner

After a brief account of the differences between the control of underground fires and those on the surface, the paper describes the analogue detection system used on the mines of the Anglo American Corporation of South Africa Limited. The system comprises Spanair gas analysers, Becon combustion-particle detectors, a telemetering system, a surface signal-recording and-processing system, and an alarm system. The use of the system is described and illustrated.

Jan 1, 1982

By J. E. Robinson, W. Pilkington, J. L. Taylor, B. J. Bluhm, E. B. Viljoen, P. Le Grange

The Chemwes uranium plant was designed and constructed within fifteen months; commissioning started during. June 1979, and the plant was producing at design capacity four months later. This account highlights the procedures and methods adopted to bring the plant Into production. The description of the various phases includes some details of the early evaluation, and the feasibility and optimization studies; of the financing, project management, design, construction, and commissioning of the plant; and of the training of personnel. Some of the mistakes made and the factors that contributed to the success are also listed.

Jan 1, 1981

By I. Zh. Bunin, M. V. Ryazantseva, V. A. Chanturiya

The paper proposes a new method for selective calciferous separation. The effect was achieved through the application of the combination of high-power electromagnetic pulses (HPEMP) and a specific reagent regime of the flotation. The combined application of HPEMP with the special reagent regime allowed for the improvement of the scheelite floatability: the recovery of CaWO4 rises from 41.2 % (untreated sample) to 58.5 (sample treated at 103 pulses). In contrast, the floatability of calcite decreases significantly: the recovery of calcite drops from 74.7% (untreated sample) to 41.1 % (sample treated at 103 pulses). The conditions were found for the selective separation of the minerals with very close flotation properties. Keywords: Calcite, scheelite, flotation, high-power electromagnetic pulses, DRIFT, XPS

Jan 1, 2020

By T. Orupold

This paper covers the commercial development of gravity separation of fine particles using a Lamella High Shear Rate REFLUX? Classifier (REFLUX? Classifier), focusing primarily on coal applications. The REFLUX? Classifier is a fluidized bed device that incorporates a system of closely spaced parallel inclined channels located above the fluidized bed. These channels make it possible to achieve a significant suppression of the effects of particle size, resulting in a highly effective separation on the basis of density. The improved gravity separation performance is shown to be remarkably high, with a significant reduction in the variation of separation density with particle size, and a significant reduction in the change in Ecart probable error (Ep) with size. The first full commercial-sized units of the REFLUX? Classifier were field-tested in late 2009 in coal applications. More recently, the technology has been applied in fine particle separation in minerals applications and there are a number of full-sized units operating in chrome applications in South Africa. Initially, pilot-scaled units (typically the RC?300) were trialled in iron ore, mineral sands, and manganese plants amongst other minerals, typically after other technologies failed to achieve the desired results. Currently a number of laboratories globally are carrying out more testing in minerals applications. More than 50 RC? units are now operating in coal and minerals applications. This paper introduces the REFLUX? Classifier technology, identifies commercial applications, and gives some commercial results.

Jan 1, 2014

By T. F. Muller

In recent years, a great deal has been written and spoken, both in our country and overseas, about the dangers posed to the environment and the ecology by mining operations. The object of this address is to put this problem, and it is a real problem, into reasonable perspective. I shall try to present the various facets that merit consideration as objectively as possible. In doing so, I shall examine the following factors: Book review National Coal Board. Gate belt conveyors. London, H.M.S.O. (Price 95p.) Although the preface of this handy little book states that it has been written for the guidance of miningoperation trainees, it will prove valuable to the practising engineer as well. NIM reports Report no. 1733 A mineralogical investigation of weathered carbonatite from Salpeterkop. (14th Apr., 1975; re-issued 28th Feb., 1978). Report no. 1823 The recovery of gold and pyrite from a residue dump at Crown Mines. (10th Jul., 1976; re-issued 28th Feb., 1976). Report no. 1829 An investigation of weathered carbonatite from Salpeterkop. (20th Jul., 1976; reissued 28th Feb., 1978). Report no. 1932 A BASIC computer programme for the evaluation of intensity data from the Telsec Lab-X-250 Analyser. (12th Jan., 1978). Report no. 1940 The extraction of the noble metals with n-octylaniline, and its application to the analysis of platinum-bearing materials. (30th Jan., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). Report no. 1945 Analyses of the NIMROC reference samples for minor and trace elements. (28th Feb., 1978). International futures conference A conference entitled 'The Road Ahead' is being organized by the 1820 Settlers National Monument Foundation to be held in Grahamstown from 3rd to 7th July, 1978. Conference of metallurgists The technical programme has been established for the 17th Annual Conference of Metallurgists sponsored by the Metallurgical Society of the Canadian Institute of Mining and Metallurgy. This year the Conference will be held in Montreal, Quebec, on 27th to 31st August, 1978, together with the 8th Hydrometallurgy Meeting.

Jan 1, 1978

By J. D. Austin, D. G. Kringe

Rates of return realized on investments in the gold mines of the newer goldfields outside the Witwatersrand were calculated and analysed over various time intervals and on various bases. It is shown that these rates of return are strongly correlated with changes in the gold price and cannot be equated with the returns that are expected when investments are made, and that the changes in gold price also affect the rates of return on the Johannesburg Stock Exchange as a whole. These correlations are used, together with a limited application of the Capital Asset Pricing Model, to suggest the expected levels of threshold returns in real terms for new mining projects, for projects on existing mines, and for share valuations.

Jan 1, 1980