Search Documents

By T. A. Chepushtanova, B. Mishra, E. O. Kilibayev, V. A. Luganov

"The paper contains the results of studying about modification of pyrite and arsenopyrite specific surface and porosity at their thermal decomposition. The studying of specific surface was carry out by B.E.T. – adsorption of nitrogen at his boiling-point. In our work were using the electron-microscopical, X-ray structure analysis and chemical analysis. There was established that the decomposition of pyrite and arsenopyrite accompany by increasing of pores volume from 0.303 · 10-3 to 1.23 · 10-3 at increasing of pyrite degree of decomposition about 41 % and then decrease about 0.131 · 10-3 m3/g at degree of decomposition near 100 %. The surface area of pores increase from 0.31 to 1.085 m2/g with following lowering due to enlargement and confluence of minor, small pores. Increasing of porosity accompany with increasing of particles windage that appear the result of heightened dust-furnace partially decomposing pyrite and arsenopyrite particles by air flow from furnace reaction zone. This explains heightened contention of sulfide sulfur in roast dust of sulfide concentrate. 1. INTRODUCTION As a result of ore base exhaustion of ferrous and nonferrous metallurgy at metallurgical treatment are involving more complicated and less qualitative ores. Magnetiting ores content considerable quantity of pyrite complicative the technology of iron extraction. At the same time the pyrite concentrates wining at dressing content different nonferrous metals in industrial quantities. Extracting ores of nonferrous metals are contenting considerable quantity of arsenic at the present time. Extraction of base metals from complicated raw materials demands new technologies. Arsenic contenting in ores is necessary to utilize (waste burial) in more ecological compatible form. Arsenic on acting metallurgical and chemical enterprises from technological cycle is withdrawing in the form of arsenate – arsenite cakes, burial of their may lead to seriously ecological problems as times goes by. In Kazakh National Technical University is carry out the cycle of researching by pyrite, arsenopyrite and arsenate – arsenite cakes treatment with the object of arsenic withdrawal in sulfide form – in more ecological and safe form and with the object of preparation of initial ore raw materials to following pyro- and hydrometallurgical treatment. As a result of sulfidizing of arsenate – arsenite cakes by pyrite are forming the volatile arsenic forms and pyrrhotite of variable structure."

Jan 1, 2008

By Antonio de Ita, Isaias Hilerio, Miguel Barron

"The influence of an unconventional lance with a central nozzle on the multiphase fluid flow in a steelmaking converter is studied in this work by means of computer simulations. The lance has four peripheral supersonic nozzles and a vertical central nozzle. Besides, the oxygen flow in the central nozzle is considered independent from the main oxygen supply. Transient two-dimensional numerical simulations were carried out considering just molten steel and gaseous oxygen as the existing phases. Numerical results show that bath agitation and droplet generation are enhanced as a result of the central nozzle. However, the performance of this lance strongly depends on the distance of the lance tip to the molten steel surface and the velocity of the oxygen jet.IntroductionCurrently, two thirds of the world crude steel is produced through the steelmaking oxygen converter [1]. Given the unquestionable economic importance of this technology, any improvement or optimization proposal is welcome. In the majority of current oxygen converters a top oxygen supersonic jet is blown onto the molten steel through a water-cooled lance to eliminate by oxidation some impurities such as carbon and phosphorus. Conventional lances have inclined peripheral nozzles whose number depends on the converter capacity. During the process, a large amount of gases evolves, forming metal droplets and a metal-slag-gas emulsion [2]. The droplets and the resultant emulsion increase the reaction interfacial area, promoting in this way carbon removal and dephosphorization of the molten steel bath [3]. However, during the blowing stage, the emulsion rises towards the lance and converter mouth and frequently forms layers which accumulate in the lance, reducing the life of the lance tip [4, 5]. It is possible that some freezing of the molten metal occurs due to the low oxygen injection temperature, however there are no reports on this. Besides, frequently undesirable operating phenomena such as spitting and slopping may arise as a result of inappropriate blowing practices or bad lance design. In the oxygen steelmaking industry, novel lances design are needed in order to enhance the decaburization rate and the slag formation and, at the same time, preventing operating practices that decrease productivity and move away the shop from safety standards."

Jan 1, 2012

By Wei-ling Wang, Ryosuke O. Suzuki, Xiang-ning Meng, Miao-yong Zhu

"A finite-element thermal-stress model of continuous casting mold is conducted to predict deformation of copper plates and its change with different cooling structure. The results show that deformation behavior of copper plates is mainly governed by cooling structure and thermal- mechanical conditions, deformation amount is related to structure geometry, and a small deformation mutation occurs in cooper-nickel boundary due to different properties. The maximum deformation of hot surface centricities of wide face locate at 100 mm below meniscus and that of narrow face locate at meniscus and terminal of water slots and significant curvature fluctuations on both sides of copper-nickel boundary. The maximum deformation of centricities is increased up to 0.05 mm with thickness increment 5 mm of copper plates, and maximum deformations are only depressed 0.01 mm and 0.02 mm with increments of 1 mm nickel layer thickness and 2 mm water slot depth respectively.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipate in primary cooling zone and make continuous casting mold under enormous heating load giving rise to thermal stress, deformation, high-temperature fatigue and creep not only depress mold life-span, but reduce casting stability [1] Many studies focused more on heat transfer, solidification and shrinkage of solidifying shell to provide inverse proposals for optimizing cooling system and even designing new taper of mold [2,3], but it is generally useless to those of having been manufactured or being put into production. Therefore, mold-related forward problems show necessity to be discussed deeply, and stress and deformation distributions based on special thermal conditions in mold should be analyzed in order to explore suitable cooling structure of mold directly. Samarasekera et al. [4] examined heat flow and distortion of two-dimensional longitudinal sections and investigated effect of cooling water velocity, copper plates thickness and carbon content on formation of rhomboidity and longitudinal comer cracks. O'Connor et al. [5] developed a three-dimensional mathematical model to compute thermo-mechanical state in thin-slab mold and calculated temperature and deformation of mold wall to assess roles of various process parameters on impacting mold life. Thomas et al. [6] predicted temperature, distortion and residual stress in mold and indicated increased distortion requires increased remachining, which reduces mold life and increased residual stress increases the probability of a catastrophic crack failure. Park et al. [7l determined heat-flux profiles in funnel-shaped and parallel thin-slab molds based on an inverse heat conduction model and thermocouple temperature measured in-plant and put them into three- dimensional finite-element thermal-stress model to predict temperature, distortion and residual stress of mold wall. Korie et al. [SJ focused on prediction of temperature, distortion and residual stress in mold and in particular to clarify that mold life is significantly affected by temperature and its rigidity, but little effect by mechanical including clamping force, bolt prestress, friction and ferrostatic pressure. Meng et al. [9l predicted temperature and thermal stress in a slab mold and analyzed effect by cooling system geometry and casting speed quantitatively. In present study, a three-dimensional finite-element thermo-mechanical model with type-switched element is transformed from previous heat-transfer finite-element model [9l, and mold deformation is simulated in order to shed light on thermo-mechanical behavior with special thermal conditions and different mold geometry at high casting speed."

Jan 1, 2013

By Biserka Lucheva, Tzonio Tzonev

"Recycling of aluminum scrap and dross is significant in the economic and energy saving, as well as in the environmental protection. Recovery of metal aluminum depends on many factors. The aim of this work is to investigate experimentally the metal recovery under different conditions. The processing of aluminum dross was carried out in DC electric arc rotary furnace. The optimal technological parameters are determined. It is turned out that the presence of crushing refractory bodies during the processing of the aluminum dross in the rotary furnace increases the degree of aluminum recovery with about 10 %.IntroductionCompact and granular aluminum dross are used for the fulfillment of the experiments, which were obtained by salt free melting of aluminum scrap. The only preliminary preparation of the compact dross is crushing them into proper size, in compliance with the size of the opening for furnace charging and removing of fraction – 1 mm. The granular dross is subjected to sieving also with the purpose to remove the fraction – 1 mm. In these conditions the content of the metal phase in the compact dross is 72 %, and in the granular – 77 %. The processing of aluminum dross was carried out in DC electric arc rotary furnace (Figure 1).The purpose of this research is to investigate experimentally the metal recovery under different conditions and to establish the dominant factors, which need to be controlled."

Jan 1, 2008

By F. L. Marley

Small and medium-sized flotation plants with no assaying instrumentation still depend much upon the art of the operator to produce acceptable and consistent results. Improved performance can be accomplished by the use of the simple microscope set up as a control device. The visual recognition of products in the circuit does much to eliminate uncertain shift operating decisions and is an easy technique to acquire. Mineral staining methods further assist in the determination of components within the mill products. Simple mounting upon scotch tape and other adhesives is rapid and convenient. The microscope also has a practical role for the plant metallurgist or laboratory technician when evaluating middling products, and their routing within the circuit. Examples are reviewed where the microscope has been used for operational control in both sulfide and nonmetallic mineral flotation plants.

Jan 1, 1981

By R. P. Rao

In rare earth (RE) based phosphors, high luminous efficiency is possible due to their restricted emission limited to specific narrow bands. In general, these phosphor materials consist of RE ions as activators/sensitizers and/or hosts. Development of various phosphor host matrices such as alkaline earth chlorophosphates, aluminates and silicates activated by Eu(2+) as blue component, borates and phosphates of lanthanides and alkaline earth aluminates doped, with Ce/Bi and Tb as green component and Eu(3+) activated yttrium oxide and vanadate as red component has been described. Luminescent characteristics, color coordinates and suitability of these phosphor materials in high efficiency new generation lamps are presented and discussed.

Jan 1, 1989

By Cui Wang, Kexin Jiao, Qiuye Cai, Jianliang Zhang

Prolonging the campaign life of the blast furnace has been an important task for iron makers, and it has been studied for decades. Adding titanium-bearing materials is a generally agreed and effective technique to protect the blast furnace hearth. Titanium from titania additions in the burden or tuyere injection react with carbon and nitrogen and form scaffolds on the hearth surface to protect the hearth from subsequent erosion. In this article, the progress on blast furnace hearth protection of titania additions in Chinese steel companies and research institutions is investigated, and the difficulties in the operation and production, such as little effect after adding titaniumbearing materials and the property deterioration of liquid iron and slags, are analyzed. The future research for protection in Chinese blast furnace is proposed, and a comprehensive process which combines protection of titanium bearing materials with reasonable thermal balance and slagmaking regimes should be established.

Jan 1, 2015

By Jouko Kallionen

Advanced Flotation Technology is the application driven design of flotation cells to achieve the optimum performance for each type and grind of flotation. This can be applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Standard, engineered, components are matched to provide mechanism design and cell dimensions for each case according to feed parameters and flotation type. Advances in process control have been achieved with high level controls and operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed. Excellent results of this Advanced Flotation Technology in large scale porphyric copper ore have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified.

Jan 1, 1999

By Toshihide Ito, Jie Liu, Takashi Nishiyama

"Human society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society. The increase pattern of supplemental energy is similar to that of mineral production throughout the world. Low positive and stable long-term increasing occurred before 1950, whereas they increased quickly after 1950, especially between 1950 and 1973. A substantial decline in· the growth of energy and mineral production began in 1973 and lasted until the early 1980s. Production of energy resources has recently begun to increase again at a high growth rate in the world. Observing the consumption trends of energy and key metals, it is clarified that increasing patterns can be thought in three stages.IntroductionHuman society evolved from an agricultural to industrial and, subsequently, to a service society. As the resource requirements for each stage of this development differ, trends of metal and energy consumption are related to shifts in society [1-3]. Humphreys [4] described that both the non-ferrous metal consumption and the construction material consumption showed a similar trend dropping markedly in the UK over the period 1960-1992. On the other hand, per GDP (Gross Domestic Product) consumption, that is, the intensity of use of construction materials has declined sharply over the past 30 years, more so than the intensity of metal use in the USA [5]. Nishiyama [6] observed that increase pattern of supplemental energy is similar to that of mineral production throughout the world."

Jan 1, 2000

By Charles Washburn

The authors review mercury sources, and contaminant streams, with particular emphasis on mercury that is extracted from precious metal ores. The design and operation of both large and small mercury distillation facilities are detailed. The relevant properties and characteristics of mercury and mercury vapor are presented. Facility engineering with respect to industrial hygiene, area ventilation, and material handling is presented.

Jan 1, 2003

By H. Kurokawa

Sumitomo Metal Mining decided to expand copper production capacity of Toyo Smelter and Refinery to cope with the recent copper demand growth in Asia, and to survive by reducing cost. The expansion plan is promoted to increase electrorefined copper production capacity from 270,000 metric tons in 2001 to 450,000 metric tons in 2007. The major changes in smelting section are introduction of the rotary steam dryer, renewal of the feeding system for flash furnace, improvement of the concentrate burner, modification of the flash furnace cooling materials, renewal of the slag cleaning furnace, modification of the flash furnace waste heat boiler, installment of a new converter furnace, enlargement of two anode furnaces. In addition, the gas cleaning system was upgraded and the second acid plant was installed. In the refinery section, the existing tank houses have been operated at high current density of 300A/m2 using the conventional starting sheet cathode technology and moreover a new tank house utilizing the permanent cathode technology was constructed. Although the copper production capacity has been increased, SO2 emission has been kept the lowest in the world through consideration of influence on the environment by expansion project.

Jan 1, 2006

Most of the world's zinc metal is produced via the roast- leach-electrowinning (RLE) process. The process is well established, but most of the sulphur in the sphalerite concentrates reports in the acid, which has to be stored and/or sold. There are significant incentives to develop a simpler process with much reduced acid generation. Ferric ion is a well known oxidant for most sulphides, in particular sphalerite, and it converts the sulphide to elemental sulphur. Based on stoichiometry, however, the amount of ferric ion needed to achieve acceptable zinc extractions is prohibitive for downstream zinc recovery from the leach solutions. The process suggested here makes use of less-than-stoichiometric ferric sulphate additions because the ferric ion is regenerated by sparging SO2/O2 mixtures. This regeneration can be effected in-situ in the leach vessel or outside the leach vessel. An example of the application of this new process is presented for a Canadian sphalerite concentrate assaying 60% Zn. The effects of temperature, ferric concentration and ferric ion regeneration are presented. Options to recover zinc from the leach solution are also briefly discussed.

Jan 1, 2000

By Carlos Schvezov, Eliana Agaliotis, Alicia E. Ares, Mario Rosenberger

"The interaction between a solidification front and a spherical particle was modeled and simulated in order to study the phenomenon of ""pushing"". Finite element methods were employed in axisymetric domains. The drag force is calculated from the calculated fluid flow field and the repulsion force is the Lifshitz-Van der Waal force. The thermal field is decoupled from the force field. The model is applied to a metallic matrix containing particles with similar, lower or higher thermal conductivities than the matrix, resulting in planar, convex and concave interface shapes, respectively.The results show that the critical velocities for pushing for concave and convex interfaces are about one order of magnitude larger and one order of magnitude lower than the critical velocity for flat interfaces, respectively. The simulated results were in very good agreement with reported experimental results.IntroductionThe solidification interface of materials containing spherical particles in some cases can push the particle ahead the interface. This phenomenon generally occurs during the solidification of different materials such as, metallic alloys containing native particles, metal matrix composites containing particles or fibers as reinforcements and crystallization of semiconductor, optical, optoelectronic or biological materials. In all cases the interaction strongly determines the distribution of particles and the resulting physical and physic-chemical properties of the resulting material. The phenomenon has been investigated for many years both experimentally and by mathematical modeling [1-21]. The process is complex due to the variety of phenomena involved during pushing. In all cases, the physical problem depends on the properties, nature, and morphology of the interacting media; the particle, melt and solid; and external fields such as gravity, thermal and electromagnetic fields."

Jan 1, 2012

By Seung-Whee Rhee

Characteristics of ceramic support made by spent foundry sand-loess mixtures are investigated by bulk density, porosity, durability, and compressive strength. And the basic properties of SFS and loess are estimated. The effect of drying time after cutting process, elevated temperature time, sintering temperature, and sintering time is also estimated to obtain the optimal condition in the process of manufacture ceramic supports. From the basic properties of SFS and loess, the content of SiO2 in furan sand is much higher than that in loess but the content of Al2O3and Fe2O3 in furan sand is much lower than that in loess. In order to make ceramic supports cylinder shape is the most desirable to sustain the properties of ceramic support. If annulus shape has a enough compressive strength, however, annulus shape may be decided. For the optimal condition to manufacture ceramic supports, drying time after cutting process is decided to 24 hrs and elevated temperature time is decided by 9hrs. And sintering temperature and sintering time are decided to 900 and 9hrs, respectively in order to prevent solidification of sand materials.

Jan 1, 2006

By R. E. Fanning

"IntroductionThe Aluminum industry is one of many materials industries which strive to make their material the preferred choice for large volume products. In some applications one material has a natural advantage over others, but more frequently several materials compete with one another, each providing one or more advantages and some trade-offs. Customers may design their product with several objectives such as minimum system cost, maximum customer appeal or maximum manufacturing flexibility, choosing materials which best combine cost and performance. In such markets it may become necessary for a material supplier to enhance the attractive features of the particular material to outweigh its disadvantages.It is difficult, if not impossible, to predict how various materials will evolve. Technological breakthrough, government regulations, material availability or sociological issues may redefine the balance between competing materials. In spite of some uncertainty regarding the competitive position of competing materials, there is little doubt that unrelenting pursuit of product quality improvement and cost reduction are essential to future viability of the aluminum industry. It is the intent of this paper to identify some areas where technological improvement would be beneficial. Thus this paper is a collection of briefly described problems that will hopefully stimulate the thoughts and research required for knowledge based solutions. Rolling ProcessA particular example is the beverage can industry where aluminum, steel, glass and plastics vie for a share of the m.arket. The high cost of aluminum relative to steel or glass requires minimizing the amount of metal per can. The high intrinsic value of aluminum has led to extensive recycling of cans although net metal cost is still higher than that of the competing materials. Intensive engineering of the beverage can led to improved design and better understanding of material requirements. These improvements permitted substantial reduction in sheet thickness over the past decade. The downward trend in metal thickness for beverage can sheet is shown in Figure 1."

Jan 1, 1988

By Mark W. Sajewycz

Creating technology, securing patent rights, and managing a patent portfolio are time-sensitive and dynamic activities. Agreements should be in place with technology partners (employees, contractors, joint venture partners), prior to embarking on research and development projects, so as to mitigate future disputes over patent rights. Technology partners should be educated on patent law basics so as to be mindful of patent bar triggering events. Accurate records must be maintained to capture information relevant for preparation and filing of patent application, including subject matter, names of inventors, and invention date. Developed inventions should be evaluated for whether to file for patent protection, delay patenting until technology is further developed, maintain trade secrecy, or effect deliberate public disclosure. Once decision is made to file for patent protection, time is of the essence, and application for patent protection should be filed as soon as possible, as many countries award patents on a "first-to file" basis. Decisions on where to file are made having regard to potential competitive advantages versus cost considerations, and can be delayed by taking advantage of priority rights recognized in patent legislation of most countries. Once patents are granted, competitors must be policed for potential patent infringement, and legal action may be necessary to prevent patent infringement.

Jan 1, 2006

By Luis Velazquez, Andrea Zavala, Nora Munguia

"This paper is aimed at describing the evolutive strategy in which the University of Sonora is following for optimizing the organic and inorganic material life cycle in the products used on campus. The institutional strategy has be oriented towards new patterns of behaviors in order to integrate the principles of sustainability as a guideline for preventing, eliminating, and/or reducing the negative environmental and occupational impacts generated when performing university substantive functions of teaching, research, and outreaching and partnership as well as its management operation tasks.IntroductionThe University of Sonora is the largest and most important university among several other universities in both the city and the state. It is a public university with a 29,792 students in three campuses in the state. The main campus of the University of Sonora is located in the capital city of Hermosillo, which has a population of more than 609,829, in the state of Sonora in the northwestern region of Mexico [1].Despite the fact that in the University of Sonora there were, in the eighties, some projects dealing with environmental issues, there was not until 1992 that the sustainability efforts were really initiated. It happened when the Sustainable Development Group was created in the Department of Industrial and Systems Engineering as a response to the need for adapting the industrial engineering curricula to the challenge of sustainable development [2]. In order to promote sustainability, it has been necessary to cope and break with several university paradigms. For this reason, the strategy for becoming a sustainable university has continuously evolved throughout the years from a simple structure composed by individual and isolated projects to a systematic and integrative Sustainability Management System. Thanks to this evolution, the University of Sonora has won a respectable reputation in the greater community and it is seen in the region as an icon of sustainability promoter. In this sense, the substantives functions of education, research, and outreach and partnership, which are considered supportive and integrative, have also evolved to play a key role for the success of sustainability initiatives.The institution has followed four avenues for becoming a sustainable university; education, research, outreaching and partnership and greening the campus [3]."

Jan 1, 2008

By Peng Fan

Liquid phase tends to migrate from an aggregate of solid particles immersed in a liquid phase into another aggregate composed of the same solid particles and liquid but with smaller particle sizes and/or lower volume fraction of the liquid phase. This type of liquid migration in a two phase system can be attributed to the driving force for the system to decrease its total interfacial energy. With liquid migration pressure as a convenient measure for the total interfacial energy of a solid-liquid two-phase system, liquid migration can be attributed to the existence of liquid migration pressure gradient in the two-phase system. The kinetics of liquid migration is of great practical importance for many industrial processes, one of which is the liquid phase sintering of functionally graded WC-Co composite materials. During liquid phase sintering, WC-Co composite forms a typical solid-liquid two-phase system where solid particles of WC are immersed in liquid Co. For a sample composed of two layers of WC-Co with the same Co content but different WC particle size, Co gradient will be formed during liquid phase sintering; while for a sample composed of two layers of WC-Co with the same WC particle size but different Co content, the Co gradient will be eliminated during liquid phase sintering. The formation and elimination of Co gradient are controlled by the liquid migration pressure gradient. This paper describes a numerical simulation of the kinetic process of the formation and elimination of cobalt gradient.

Jan 1, 2006

By Michael J. Mankosa

The increased emphasis placed on recycling of consumer and industrial waste products has generated a need for advanced separation techniques for recovery of valuable by-products. As a result, the metals recycling industry has made great strides in the recovery of used wire products through the application of chopping and screening processes. Unfortunately, in many instances, the final plastic reject still contains a substantial portion of valuable metal. Typically, this material has been discarded, since an appropriate separation technique has not been available. Recent work conducted by Carpco, Inc. in Jacksonville, Florida indicates that a high-grade metal and/or plastic product can be recovered from this waste material using a novel density separation process. Extensive test work has been conducted using this procedure to validate separation performance as well as equipment capacity. This paper will present the basic operating principle of the separator, as well as results from tests conducted using various feed materials.

Jan 1, 1995

By Shaik Jeelani, Esperidiana A. B. Moura, Vijaya K. Rangari, Roberta A. Lima, Rene R. Oliveira

This work present the preparation and characterization of biodegradable nanocomposites based on aliphatic-aromatic copolyester (PBAT)/polylatic acid (PLA) blend reinforced by TiO2 nanoparticle. The biodegradable polymeric nanocomposites were prepared by melting extrusion process using a twin-screw extruder machine. The influence of the TiO2 nanoparticle addition on mechanical and thermal properties of PBAT/PLA blend was investigated by tensile and impact tests, SEM, DSC and XRD analysis and the correlation between properties was discussed.

Jan 1, 2015