Search Documents

By Kwang-Yeom Kim, Dong-Gyou Kim, Hyo-Kwan Yoon

This study was intended to simulate the blasting model using notched-hole with numerical approach. Numerical analysis approach was applied to compare and evaluate the blasting model using notched-hole and circular hole. To implement non-linear dynamic blasting model, blasting analysis was carried out with AUTODYN code. Behavior of two models was compared and evaluated using AUTODYN and visual analysis and quantitative evaluation based on pressure and stress to verify the effect to induce the destruction territory to the specific direction when blasting with notched hole was attempted.

Jan 1, 2010

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By B T. Lusk, John J. Silva Castro

The signature hole method uses a convolution operation to predict the waveform of a production blast based on the record of a waveform produced by a single blast hole. Convolution is a mathematical operation on two functions, (generally the product) to produce a third one. Recent research communication and publications highlight a lack of discussion in the literature about the available methodologies to calculate the convolution for blast vibration prediction. The goal of this paper is to discuss and present in detail for students in ground vibrations from blasting, several techniques to calculate the convolution between signals when the signature hole method is used. Convolution is a straightforward operation when signals produced by each hole are assumed the same, however; variations in the signals from each hole in a production blast require a more complex convolution operation. A graphical procedure is shown in this paper to solve a convolution when signals vary hole-to-hole (as expected in a mining production blast). The graphical methodology was tested using a recorded blast event and the results were compared to the regular mathematical procedure (convolution) and the results from a commercial software used in the mining industry. Results show that the graphical procedure is in agreement with the results from the other two.

Jan 1, 2014

By Grant Small, Deon Pieterse

Reactive ground conditions at an open pit manganese mine in the Northern Cape of South Africa resulted in an unexpected detonation.

Feb 1, 2020

By Z X. Zhang

If the iron ore loss is 15% in the process of mining, the total iron ore loss in the world will be about 461 million tons, this is equal to the total production of 230 iron ore mines each of which produces 2 million-tons of iron ore per year. Based on a series of blast tests in the Malmberget mine, this paper shows that ore recovery can be markedly increased by improving blasting technology such as choosing a correct primer position and making use of shock wave collision. The paper further suggests that a high ore recovery can not only reduce natural resource loss and mining cost but also prolong the life of a mine. In addition, the paper shows an example of reducing blast-caused rock damage in the roofs and walls of underground drifts (tunnels) by using new blasting methods in the Malmberget mine. Finally, the paper shows how the Malmberget mine has successfully reduced the ground vibrations, without adversely affecting fragmentation and ore recovery in sublevel caving mining.

Jan 1, 2014

By Harley Cheema, Brandon Fryman, John Tatom

A new magazine propagation model has been proposed by the IMESAFR Science Panel for eventual implementation into the IMESAFR QRA program. Initial results from this QRA propagation model are now available.

Feb 1, 2020

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The University of Kentucky employs an explosively driven shock tube in the course of experimentation. A good deal of the work completed relates to the verification of blast mitigation products and strategies. The work is dependent upon reliably reproducing specific pressure time histories called out by the test in question. The facilities are located in the workings of an underground limestone quarry in Georgetown Kentucky. As such, the temperature maintains fairly consistent 60°F (15.6°C), making it a comfortable work environment year round. Unfortunately, the relative humidity follows the prevailing weather conditions allowing a wide variation, especially between the winter and summer seasons. A study was undertaken to gauge the influence of relative humidity on shock wave generation, including the positive and negative phases of the wave.

Jan 1, 2011

By Lloyd Litwin

The ARTA 2008 Project (Alpha Ridge Test of Appurtenance) was a Canadian Government sponsored deep water seismic survey carried out on the high arctic permanent polar ice cap. This Geological Survey of Canada operation was the second seismic research project in the high Arctic and was monitored by the Danish Government. Utilizing 100% air support from Eureka and then helicopters from an ice based tent camp north of Ellesmere Island, the five week study was accomplished in the early spring just after the sun returned to the far north.

Jan 1, 2011

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By Rob Farnfield, Ben Williams

The A5 road in the United Kingdom forms an ancient and well-used route through the hills and mountains of North Wales. In the 1990?s a programme of work was conducted to upgrade the road to modern standards. As part of this work a new cutting was constructed to bypass a portion of road routed through a gorge close to the village of Ty Nant. This new cutting was formed by drilling and blasting and included much pre-splitting and extensive rock bolting. This operation caused much concern to local residents relating to vibration, air overpressure and flyrock.

Jan 1, 2011

By Tapan Goswami, Stephen Jeric, Geoff Brent

Highwall failures in large deep open cut mines have very significant safety and commercial implications. There are many factors influencing the stability of highwalls. The major influence is the interaction of the local geology with the shape of the pit wall. This factor is in the realm of the geotechnical engineer and is beyond the control of the blasting engineer. However, a secondary influence is the blastinduced damage to the wall. In most open cut metal mines the blasting strategy to control this damage involves the use of separate production and trim blasts bounded by presplits at the final wall.

Jan 1, 2011

By Selamawit Asfaw, Mohamad Sharif

In recent years, the use of modal analysis has increased to include many different aspects of the construction industry. Computer modal analysis can be used in determining the dynamic properties of a structure by mathematical equations and knowledge of the structure’s physical properties. This technique can now be used to predict the level of vibration induced by blasting on adjacent structures. Ground vibration induced by buried explosives is a major concern for contractors when excavating near utility pipelines such as gas and water lines. The size limitations placed on easements causes the necessity of additional utility lines to be placed in close proximity to existing lines. Through the development of computer models of the pipe, stress analysis can be performed prior to blasting. Based on the calculated dynamic properties (natural frequencies and modal shapes) and the maximum allowable displacements and stress levels (which are established by the pipe manufacturer) the allowable maximum charge weight per delay can be selected for the blast. The selected maximum charge weight per delay will ensure that the resulting pipe peak particle velocity level is within 95% confidence. This means, statistically, there exists a 95% probability that the actual pipe peak particle velocity would be less than the predicted value. The pipe is then instrumented with vibration measuring sensors to ensure that vibration levels are within the allowable maximum pipe strength. In conclusion, this technique can assist the engineers and blasters, to establish the proper blast design. It allows for safe and efficient installation of additional utility lines adjacent to existing lines. This technique can also be applied to predict the structural response to blasting induced vibration for a variety of complex structures. A detailed explanation of this technique, as well as an example of application including formulas used for this technique will be provided in this paper.

Jan 1, 2000

By G G. Paine, C V. B Cunningham, G Harries

The companies of the ICI Explosives Group have successfully used a wide variety of internal computer codes including BOBCAT, KUZ-RAM, ICRAX, XPLODE, BLEND, 3CRACK, MICBLAST, DETON, etc. In recent years the extensive experiences across ICI have been combined into a single compatible model engineered to worldwide technical service and customer needs for the prediction and assessment of blast results.

Jan 1, 1987

By Dr. Anurag Agrawal, Steve Franklin, Clint Zimmerman, Elijah Williams

In a time when data has become a highly valued commodity within many mining and quarry operations, managing large amounts of current and historical information can be difficult. If not managed properly, trying to leverage the data to make informed operational decisions promotes another challenge. Geographic Information System (GIS) is an environment that uses computers and software to create, manage, analyze, and map all types of data. Currently, the mining industry is faced with a challenge to produce the demanded critical metals and minerals that drive our economies. GIS is leveraged in many large mining industries today to help drive decisions, save cost and plan for future operations. Specifically in the Drilling, Blasting and Quarrying industries, data is being captured at many different levels, whether it is a subsurface geological, blast performance, quarry surveys, loading and hauling, or crushing performance. Pen and paper logs and reports compiled lack the dimension that GIS can bring for extracting value from real-time or historical data. GIS connects data to maps, integrating location data with all types of descriptive information. Paired with Artificial Intelligence, additional analytical layers can be built on platforms to extract data and automate workflows. Having the ability to encompass several forms of collected data to drive operational decisions can bring huge savings to the bottom-line. This paper will dive into the areas where GIS data can drive value into operations by assisting in the management and analysis of the types of data being captured, specifically with Drill and Blast. Whether it is tracking haul road conditions, monitoring locations of equipment, environmental conditions, quantifying blast performance or developing a quarry plan based on geological models. GIS can collectively encompass all of this data to bring tremendous value to the operations, improving safety, efficiency and production.

Jan 21, 2025

By Rob Farnfield, Mark Pegden

Old Cliffe Hill quarry produces between 4 and 5 million tonnes of crushed granite per year and is located in the county of Leicestershire in the East Midlands region of England. Blasting is carried out with bulk emulsion explosives in combination with either shock-tube or electronic detonators.

Jan 1, 2010

By O. Cermak, F. Degonld

Although 3D fragmentation analysis is a relatively new technology, it is rapidly gaining popularity among mid-sized mining operations and quarries. The results provided by this technology are adequate, but like other picture analytic methods, it mainly focuses on the surface of the muck-pile. These results are incomplete or incorrect as falling rocks and boulders from the stemming zone are constantly influencing the muck-pile surface. This obstacle can be overcome by collecting a large amount of data and analyzing it over time. However, this is not always an ideal solution, as companies prefer to receive results immediately after the blast to make resource allocation decisions, production planning, and plan for the next blast. Over the past year and a half, we have conducted a study on various muck-pile fragmentation analysis results from 3D modeling in Central Europe, comparing the results between the surface and inside of the muck-pile. By analyzing multiple shot results, we were able to determine the percentage difference between the top and inside fragment sizes and calculate the range of correction coefficients for different rock types. Applying these coefficients to a single muck-pile surface fragmentation analysis allows us to determine the actual fragment sizes inside the muck-pile. This enables us to make informed decisions regarding loading, hauling, material mixing, and proper crushing or milling. By overcoming the limitation of surface-based analysis, we can now accurately evaluate blast performance, which leads to better processes optimization and increase efficiency. As 3D fragmentation analysis becomes more widespread, we expect to see even more benefits for the mining and quarrying industry

Jan 1, 2024

By D. Fry, S. Hunsaker

Ammonium nitrate in explosives and sulfides in reactive ground have the potential to react at ambient and elevated temperatures resulting in premature detonations. The Australasian Explosives Industry Safety Group (AEISG) published, in 2006, a Code of Practice1 for elevated temperature and reactive ground. This paper reviews the chemistry, general reactivity of various ground types, elevated temperature hazards, and testing protocols contained in the code, that are industry best practices for managing ammonium nitrate-based explosives in elevated temperature and reactive ground conditions. In addition to reviewing the 5th edition AEISG Code of Practice, data is presented validating the recommended sampling guidelines within the code. Dyno Nobel has been screening reactive ground samples and performing sleep time testing since the code of practice was first released. Test results demonstrate the effects of samples that are allowed to oxidize before testing and are shown to be subsequently less reactive and not representative of the actual hazards facing mining blasting operations. Results also show that for a given reactive ground sample, reaction times decrease with increasing temperature. Data also quantify the delay in reaction time given by inhibited products. These results emphasize the importance of proper sampling and preparation of samples to accurately characterize elevated temperature and reactive ground hazards. They also demonstrate the efficacy of inhibited products in managing these hazards

Jan 1, 2024

By Jacqueline Berendzen

Summer internships are a great way for students to explore different career paths in the industry and get first hand experiences with potential employers. As a junior in mining and explosive engineering, my 2009 summer internship gave me a behind the scenes view of the actual workings of an explosive company and the role they play in the mining industry.

Jan 1, 2010

By Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F) and prescribed in-hole residence times on the order of days. When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits. An underground mine in Western USA has several areas in their development heading with very high temperature, in view of this, they decided to use the IGNEO detonators in order to evaluate the effectiveness and performance of the system.

Jan 21, 2025