Search Documents

By X. L. Yao

This paper analyses the effects of mining extraction geometry (width/depth ratio) and dip of seam on subsidence parameters based on a large Database, containing 120 longwall mining cases all within the UK coalfields. The subsidence parameters evaluated in this paper include the following: the maximum subsidence value with different goaf-treatments, the position of maximum subsidence, the position of half-subsidence, subsidence value over the rib-side, positions of maximum tensile strains, positions of inflection points and the magnitude of maximum tensile strains on both rise and dip sides. Additionally, the maximum compressive strain and two limit angles are also studied in this paper. Based on a comprehensive Database analysis, several equations are derived relating these parameters to the width/depth ratio and the dip of seam. The results should assist engineers to design new structures, or take measures to protect existing structures from strain effects. The findings of the research assist in extension of the SEH to inclined seams with greater certainty.

Jan 1, 1990

By Ed D. Doney

Based on the subsidence data collected through a comprehensive subsidence monitoring program con: ducted over two longwall panels in an Illinois coal mine, mathematical models have been proposed for predicting final and dynamic subsidence in the Illinois coal basin.

Jan 1, 1990

By Richard J. Perin

Subsidence monitoring was conducted in proximity to the 1-A and 2-A longwall panels at Consol Pennsylvania Coal Co.'s (CPCC) Bailey Mine slurry impoundment. Monitoring fullfills federal Mine Safety and Health Administration (MSHA) mandated requirements. Construction of the monitoring network was completed between May and June, 1986. Monitoring was conducted before, during, and after mining of the panels between June, 1986 and February, 1987. The embankment was not deleteriously impacted by longwall mining.

Jan 1, 1988

By J. R. Stoltz

To date, there has been limited formal research dealing with the use of Mobile Roof Supports (MRS) for pillar recovery. This paper, which is a portion of a larger project, presents convergence data from 4 different mine case studies. MULSIM was used to create a numerical model. The resulting information from this model was then compared to the actual measured values. MULSIM was also employed to analyze the industry-accepted pillar/barrier layout for mining underground reserves with the Joy Highwall Mining System. This layout was examined for both a low cover and a high cover extreme,

Jan 1, 1999

By Eric Westman

Ground control problems caused by multiple-seam interaction frequently sterilize coal reserves. Interaction mechanisms differ for overmining and undermining and are controlled by mining, spatial. and geologic conditions at each site. A multiple-seam interaction analysis software program, UGLY (Uppersearn Gateroad Longwall Stability), has been used to evaluate sterilization of coal reserves due to overmining at three locations. Four case histories were reviewed to determine the effectiveness of improved ground control in mitigating interaction effects.

Jan 1, 1997

By Stephen Tadolini

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high¬loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

Jan 1, 2003

By S. S. Peng

In recent years many roof falls have been conveniently attributed to the adverse existence of a high horizontal stress. The normal practice of not conducting a follow-up study in a roof fall investigation usually leads to a wrong conclusion. This paper describes two cases of massive oriented roof falls in two separate room and pillar mines. The investigation in each case involved the analysis of past history and current conditions from which remedial measures were recommended and implemented. A follow-up period of up to three years was performed to evaluate the effectiveness of the recommended remedial measures. In both cases, high horizontal stress was proven positively not the cause, contrary to the original conviction of mine management Rather, a weak immediate roof was the basic cause Under a weak immediate roof, a proper roof bolting plan and adequate entry width and intersection span must be strictly observed.

Jan 1, 1999

By David Conover

Knowledge of the magnitude and direction of the horizontal secondary principal stresses is a critical factor in designing the layout and mining sequence of underground openings. Typically, horizontal stress measurement has been accomplished using overcoring or hydraulic fracturing. Hydraulic fracturing can be accomplished from surface boreholes prior to development, but the technique relies on numerous assumptions regarding the rock mass and the stress field, and interpretation of results is somewhat subjective. Traditional overcoring provides a more precise measurement, but requires underground access. To allow for precise measurement of the horizontal stress field from surface boreholes, the In-situ Stress Tool (1ST) was developed by SIGRA Pty of Brisbane, Australia. Used in conjunction with HQ wireline coring, the 1ST contains a battery-powered data logger that records tool orientation and monitors six diametral deformations as the tool is overcored. The IST has been used successfully for several years in Australia, but has only recently been introduced in the United States This paper discusses how the IST was used to measure the pre¬mining horizontal stresses at a western U.S. coal mine. Seven successful measurements were obtained in two holes at depths ranging from 250 to 800 ft. Results were consistent, showing moderately biaxial stresses greater than those expected from gravity loading, but relatively low compared to rock strength. In addition to describing the overcoring equipment and procedures, various problems encountered during testing and the accuracy of the results will be discussed.

Jan 1, 2004

By Hamid Maleki

The U.S. Bureau of Mines implemented a monitoring program in a western U.S. coal mine for the evaluation of both conventional and alternative support systems. The conventional support consisted of 2.5-m-long vertical bolts installed in an 5.5-m-wide entry. The alternative system consisted of 2.5- and 3-m vertical and inclined bolts installed at a higher density during widening of a cut from 3.6 to 5.5 m. Roof deformation, roof stress, rib deformation, and bolt loads were monitored during the 2-month test period. In addition, roof failure patterns and lithology were characterized within the six-entry main test section. Results were analyzed using roof deformation and failure profiles, roof stress profiles. bolt loading and bending moment diagrams, and numerical models. The mechanics of roof deformation, failure, and support reaction in three zones in the mine roof were characterized. Significant improvements were shown in roof stability in the section using the alternative system. Results are encouraging and indicate the effectiveness of alternative support systems and excavation techniques for limiting inelastic deformation of roof in highly stressed underground mines.

Jan 1, 1994

By Shosei Serata

Serious floor heave of up to 2.4 m in a 2.4-m high mine entry was eliminated by applying the stress control method of mining, as a last resort, at the No. 5 coal mine of Jim Walter Resources, Inc., in the Black Warrior coal basin near Birmingham. Alabama. Underground observation of the first 3-room entry created using the stress control method is discussed here. The behavior of the test entry, which eliminated the heave problem, is analyzed in relation to similar studies conducted in a salt mine under similar ground conditions by utilizing finite element analysis.

Jan 1, 1984

By Fangting Dong

The broken rock zone (BRZ) and the tunnel support theory are investigated. The relationship between the BRZ and the related factors, the interaction between the BRZ and supports, and the function of supports are analyzed in detail based on the authors' underground observations and model taste. A summary of the application of the BRZ theory in the past is also presented.

Jan 1, 1988

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

By K. Haramy

Coal mine bursts or bumps involve the violent, rapid failure of coal and rock in or around a mine excavation. Failure is normally associated with high stress and brittle or brittle-elastic materials; in coal mining, bursting may also be associated with desorbing gas, and this type of failure is termed an outburst. This paper discusses factors affecting coal mine bursts and several methods to predict bursts, including microgravity, microseismic, rheological, rebound, and drilling-yield methods. Methods to avoid burst conditions using volley firing, hydraulic fracturing, and auger drilling are also discussed. A case study is presented in which the redistribution of stresses and displacements was found to be associated with a burst at a deep longwall coal mine. The research showed that stresses are redistributed following the burst.

Jan 1, 1984

By Antoni Kidybinski

Coal mining both with longwall and room-and-pillar method often encounters severe operational difficulties due to had roof conditions. Rooffalls at entry cross-cuts or along the rib line in longwalls as welt as dynamic and excessive loads on supports due to overhanging of strong roof layers in a goab - are well known phenomena to the mine operators. Also, a number of practical examples may be quoted of dramatic improvement of working conditions after changing of coal winning technology or supports type. It is therefore a question to be answered how far we are able to recognize roof strata properties before mining starts and adjust both coal extraction technology and supports of entries to rock stability foreseen. Furthermore, engineering principles and criteria for decision making should be established. In recent years several in situ rock strength and discontinuities detection testing techniques have been developed both indirect (geophysical) and direct thus making possible closer roof-strata examination. In this paper critical roof span criterion is discussed as a basis for selection of proper mining system in terms of desirable stability of mine opening .

Jan 1, 1982

By Erdal Unal

In underground mining today, safety and economical aspects demand a better understanding of the rock-mass conditions, particularly for design of underground mine openings excavated in weak and stratified rock mass. The rock mass classification systems, in essence, are empirical approaches utilized during preliminary design stage. These systems have been developed for specific purposes and rock mass types, therefore, direct utilization of the classification systems in their original form, for characterization of complex rock-mass conditions is not always possible. This is probably one of the main reasons why designers continue to originate new systems, or modify and extend the ones already existing. RMR and Q systems, for example, although widely used in mining and tunnelling, can not fully describe the specifications of the weak, stratified and flay bearing rock mass. Consequently, the engineering applications that would be carried out based on original RMR and Q ratings could be inadequate for making design decisions even during the preliminary design stage.

Jan 1, 1990

Coal mass strength properties must be estimated to obtain realistic estimates of coal pillar strength. The limitations of existing techniques for approximating these properties are discussed. The coal mass is anisotropic. The Hoek and Brown approach to rock mass property estimation is modified to allow for this. This approach requires the Rock Mass Rating (RMR) for the strata. In the normal case where bedding is sub-horizontal, these major planes of weakness have little effect on the strength of pillars. As a result of this the RMR must be measured parallel to bedding. This means that a significantly higher rating than that usually obtained for coal is observed. The use of mass strength property estimates in extant empirical relationships is outlined. At high width to height ratios, an acceleration in the rate of increase in pillar strength with increasing width to height ratio has been observed. The empirical relationship developed by Salamon (the so called squat pillar formula) takes account of this. This relationship was found to have significant limitations with respect to its universal application. Modifications arc made to Bieniawski's empirical formula to extend its use to large width to height ratio (squat) pillars. This new squat pillar formula has none of the disadvantages associated with Salamon's relationship. Strain softening was incorporated into non-linear finite difference numerical modelling to estimate pillar strengths. The technique outlined above is used to obtain peak coal mass properties. Modelled pillar strength was found to be sensitive to both peak and post peak mass strength properties. Post peak properties were found to be difficult to obtain and required some back analysis. Modelling results were used to estimate both the strength of squat pillars and parameters for use in a now squat pillar empirical strength relationship.

Jan 1, 1992

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a shoW computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By M Nombe

Based on the analysis of a case study at POWELTON No.2 MINE, it was determined that mine stability problems had occurred due to floor softening. A fireclay (underclay) layer in the immediate floor was softening after coal extraction and failing under pillars load. The thickness of soft floor was considered as the governing factor in the determination of the magnitude of floor displacement. The effect of floor thickness on floor displacement was evaluated by creating seven models that were input into the LAMODEL program. The properties of the soft floor were determined from a bearing capacity test performed in the Mains close to the area where mine stability problems had occurred. Moisture increase was considered in the reduction of floor bearing strength. Various strain-softening properties were allocated to the materials representing the soft floor. The LOW GAP POWELTON No.2 MINE was modeled and LAMODEL program was used to determine stress and convergence on both the coal seam and the fireclay seam. The results of critical stress and convergence obtained from modeling were compared with the actual floor failure area in the mine.

Jan 1, 2002

Results of direct shear tests on rock discontinuities and triaxial compression tests on intact rocks are presented and - discussed. The main parameters considered area stress functions, angle of internal friction and cohesion variations. Primary objective of this work is to determine relationships that adequately describe the rock behaviour for design of mining excavations, while still maintaining a certain degree of simplicity.

Jan 1, 1987

By Larry Howe

Second, or retreat mhng with Mobile Roof Supports (MRS) has now been part of coal mining in the United States for a decade Their utilization has evolved into mining applications which vary in seam heights from 38 inches to 170 inches, and overburden depths from outcrop to beyond 1200 feet This paper will detail the pillaring plans, lift sequences, and mnchky utilized in these operations and the rational for the plans A comparison of the current productivities achieved will be outlined

Jan 1, 1998