Search Documents

By D. W. Morgan, K. W. Downes

"OVER half a million tons of chromite ore is used annually on the North American continent, all of which is imported from overseas. Chromite is essential in the manufacture of stainless steel, armour plate, and tool steel, to mention only three important uses. It is, therefore, a strategic mineral, and every effort should be made to discover a means of utilizing our domestic supplies.Both Canada and the United States possess deposits of chromite, but they are low grade with respect both to their chromium content and to the ratio of chromium to iron. Mechanical concentration can improve the chromium content •by rejecting gangue, but chromium concentrate produced is still lower in chromium than imported chromite and, more important, the ratio of chromium to iron is only about half that in the imported material. At present, a chromium to iron ratio •of 3:1 is desired by industry. To obtain this .ratio in the case of domestic ores, a chemical attack on the chromi'e is necessary."

Jan 1, 1952

By W. S. Urbanski, A. L. Devernoe, R. W. Stuart, M. S. Walker

"Although many investigators have successfully achieved separations using variations of a concept wherein particles are buoyed upwards against gravity in a magnetically attracted fluid, none have succeeded in separating fine particles in a manner that is practical tor mineral beneficiation. This paper describes laboratory tests and preliminary economic analyses for a new mineral separation process which provides enhanced magnetic buoyancy and separation capabilities. The process provides a means of gravity separation in a regime where conventional gravity separation is inadequate; that is for small differences in mineral densities and for very fine particles. Although early interest centers on gravity separation, the process has also been successfully used for precise magnetic separation.Tests were conducted on a variety of mineral mixtures, ore samples and concentrates including; a sphalerite ore, pyrochlore ores and concentrates, cassiterite pre-concentrates, a chromite pre-concentrate, and heavy mineral placer samples. Separations requiring high discrimination between fine particles narrowly different in density or weak magnetic properties were obtained. Of particular interest is the ability of the process to concentrate or remove oxide minerals or gangues, especially silicates. Potential applications are discussed."

Jan 1, 1985

By Kai Bartram

The successful application of color sorting machines has established sensor-based sorting in the mineral industry in recent years and is considered today as a significant innovation in processing technology. However, we are only at the beginning of (market) introduction. New sensor systems have been developed, which exploit material properties such as electrical conductivity, magnetization, molecular structure, thermal conductivity etc. This opens up new exciting preconcentration and upgrading possibilities for many applications such as nickel, gold, copper and other ores as well as for industrial minerals, diamonds and other gem stones.

May 1, 2009

By M. Falutsu

"The PSI-200 is a rugged, innovative, and easy to install on-stream size analyzer. Its calibration is simple and can be done on-line, during operation. Two measurements are displayed on the panel, which are expressed as percent passing a selected size, or as any statistical diameter. These two measurements are given as two continuous 4-20 mA output signals. Operation alarms are displayed on the screen or are given as digital output signals.The PSI-200 has been used in various applications at Lakefield Research. Particle sizes ranging from 10 µm to 450 µm have been monitored successfully, with an accuracy of 1- 2%. Having the size measured continuously and reliably, optimum conditions have been established for the grinding circuit, resulting in a superior quality in pilot plant testing.INTRODUCTIONThe challenge of any operating plant is to optimize product quality, maximize throughput and minimize operating costs. The importance of particle size measurement at a grinding circuit is well recognized. Monitoring continuously the particle size and keeping the product as uniform as possible is crucial to the whole mill operation regardless of the nature of the operation.Various techniques and instruments have been developed over the years attempting to give reliable on-line size analysis data. The operating difficulties and the reliability of these equipment still present major drawbacks and none of them proved to be widely accepted.PSI-200 is a relatively new on-line analyzer. The operation is simple and of low cost and the maintenance required minimal. It measures particle size and it displays two parameters of the solids size distribution, either weight fraction of passing a certain size or any statistical diameter. Two analog outputs can be sent to a process control system and through a supervisory control loop the correct action can be taken to maintain the desired particle size (perhaps adjust the feed rate to the grinding mill)."

Jan 1, 1993

"The ore currently being milled at Delnite is a high pyrrhotite ore with the gold intimately associated with the pyrrhotite. To get maximum recovery of the gold with the lowest reagent cost, it is necessary to keep the pH as low as possible In the laboratory the best results were obtained with a pH of 10 but in the plant it was found that a pH of 11 was the minimum practical pH. With the n1anual control it was difficult to maintain this figure.The Mines Branch had a conductivity probe (see Fig. 1), developed by Dr. G .G. Eichholz that they wished to try out in plant operation.On June 17, 1963, the probe with all necessary control equipment was installed in the regrind circuit (see Fig. 2) at Delnite Mines. Crushed quick lime is fed at this point but it is also necessary to feed hydrated li1ne at two other points in the cyanide circuit in order to maintain the pH close to 11. 0 throughout the circuit. Only the feeding of the quick lime at the regrind mill was controlled in this test.One thing that concerned me with the operation of the probe was whether the reading on the probe chart would correspond to the pH. A look at the graph accompanying this paper will show that except for very minor variations the graphs of the chart reading and the pH reading are parallel. The upper graph shows that the pH reading and the lime titrations also correspond and that the cyanide titrations appear to have little effect on the pH reading.Table 1 gives the results obtained for the two months before and after the instal1ation of automatic control as well as the two months of control. Unfortunately there was a decided change in ore just after the automatic controls were removed. There was much less pyrrhotitc in the ore than usual thus changing the need for lime and cyanide."

Jan 1, 1964

By K. A. Hughes

Under the oxidizing conditions of the McClean Lake Tailings Management Facility (TMF) hydrocarbons entrained on the surface of tailings material from mill processes are gradually converted to soluble bicarbonate ion. This has been observed to be a process occurring over approximately three years likely encouraged by the presence of a microbiological community within the tailings mass and in the water column. A recent tailings sampling campaign has provided evidence that bicarbonate ion is participating in the conversion of gypsum to calcite. In older tailings, equilibrium with calcite appears to be controlling the terminal bicarbonate ion concentration.

Aug 1, 2010

By John Eggert, Paul Benford

"Since 1982, Placer Dome Inc. -Dome Mine has steadily increased mill throughput. Tonnage has increased from a nominal design capacity of 3000 short tons per day, attained in 1985, to 4130 stpd by the end of 1992. Many minor and major circuit adjustments were tried to maximize tonnage.Having utilized most conventional means of increasing tonnage, further increases required a newer approach. This paper discusses the Dome experience in the development and implementation of an expert system.The Comdale/C system was chosen for a controlled trial. The criteria for acceptance were: increased tonnage had to be sufficient to pay for the system; the increase had to be visibly sustainable and the mill operators had to be willing to accept the system.The criteria for purchase were met during the trial and the system was purchased. The system continues to perform well. The tonnage throughput increase has been sustained while operator acceptance remains high.IntroductionPlacer Dome Inc. -Dome Mine is Canada's oldest operating gold mine. The mine was among the first established in the Porcupine camp in what is now Timmins, Ontario. The City of Timmins is located approximately 500 miles or 800 kilometres north of Toronto. Figure 1 shows a map of the province of Ontario and the mine location.In 1912, milling began at a rate of 350 short tons per day. With two minor exceptions, milling has been continuous since this time. The first of these shut downs was in 1918 during the first world war. The war created labour shortages which forced the mine to stop production for more than a year. The second was in 1930 when fire destroyed the mill."

Jan 1, 1994

By K. G. Eriksson

"The first tentative test made to try rubber lining in grinding mills was made in the early twenties. However, because of poor rubber compounds and design the results did not prove to be promising.In the early sixties successful trials of rubber linings were carried out as a result of a cooperation between boliden AB and Skega AB.One of the reasons rubber was not used earlier for linings was the difference in wear characteristics between rubber and steel. The ability to successfully develop rubber mill liners depends on three factors:l. Design2. Material (rubber compounding)3. Experience (knowledge)DESIGNThe main difference between steel and rubber, in material aspect, is the elasticity and the low tensile and shearing strength of rubber. It is necessary to take maximum advantage of the elasticity and to reduce tensile and shearing forces by minimizing the sliding of the mill charge. This is accomplished by using the Lorrain type of liners, i.e., lifter bars and plates. It is, however, necessary to keep a certain balance between lifter bars to optimize liner life and grinding performance."

Jan 1, 1983

By Angela L. Paveley

Economic viability of base metal mining is complicated by a volatile market that can cause fluctuations in the growth and stability of the mining industry. Nickel is mined primarily for use in manufacturing industrial stainless steel and plating materials. It is essential that nickel production be sufficient to respond to current and future market demand. A Post-Pillar cut and fill mining complex is currently producing nickel sulfide in Northern Manitoba. From 2006 this area has shown a steady increase in the annual production, rising from 11 million pounds to 25 million pounds in 2010, and accounting for 33% of the total production for the Manitoba Operations. It is expected that fine-tuning the mining process can safely enhance ore recovery, improve production consistency, and increase economic viability of the deposit. The Post-Pillar Optimization study was initiated by the local technical and operational departments at the mine and analyzed from July 2010 to March 2011. The purpose of this study was to determine if portions of non-recoverable pillars can be slashed without jeopardizing pillar strength. This ideal case would optimize ore recovery and reduce variability in the ore mining rate. Numerical modeling and geo-mechanical material properties analyses, completed by the rock mechanics group, define the maximum drift width at 32 feet and the minimum pillar width at 18 feet. Thus, it was suggested that up to 3 feet could be slashed from two sides of the standard 24 foot pillars without damaging ground integrity. The field data collected indicates that additional ore could be recovered without compromising the safety of the workplace and the integrity of the complex. Consequently, technical and operational groups work jointly to achieve pillar optimization. Approximately 500,000 pounds of nickel was extracted from the complex via pillar optimization from July 2010 to March 2011. Economic analyses show the pillar optimization method developed for the mining complex is a proven, value-added opportunity. The mining complex remains a safe workplace and has retained ground integrity.

Nov 1, 2011

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By John F. Vynne

This paper will discuss several of the systems and processes that have been developed over the past few years, and are now being utilized by major mining companies on draglines in North America, Australia and South Africa. These technologies include production monitors and reporting systems, GPS navigation systems, structural integrity monitoring systems, structural analysis studies to increase the dragline RSLs, and inspection and response strategies. The use of these technologies provides significant increases in dragline production, and reduces maintenance costs and downtime. The question that needs to be asked is what value is there in monitoring? Increasing dragline productivity is dependent upon to two items with the overall goal being to maximize the number of bank cubic meters moved and to uncover more coal: 1) maximizing payload and 2) maximizing the number of cycles. If you do not measure and try to optimize the parameters that impact payload and number of cycles, there is very little chance that you can improve overall dragline productivity. These parameters are: Maximizing payload is dependent upon the following: ? Geology ? Blasting ? Monitor weighing accuracy ? Engage location ? Disengage Location ? Rigging ? Suspended load ? Bucket characteristics ? Operator skills ? Minimizing rehandle Maximizing the number of cycles depends upon maximizing digging time, and minimizing cycle and delay/down times by: ? Minimizing Operational Delays ? Minimizing Mechanical Delays ? Minimizing Idle time ? Minimizing Walking time ? Minimizing Fill Time ? Minimizing Swing Angle ? Maximizing Swing & Return Rates ? Minimizing Spot Time A third reason to monitor, conduct structural analysis studies, and have inspection strategies is to prevent catastrophic failures such as shown in the following photographs (figures 1 & 2).

May 1, 2008

By A. J. Basu

Air quality in underground mining operations can fluctuate significantly during the working day, but until recently the only way to ensure a mine had sufficient air quality was to over-ventilate and, with significant delay in adjusting the volume or direction of the airflow, working conditions were tolerable but rarely ideal. Underground ventilation management systems have been considered to achieve improved energy efficiency since at least 1995 in Canada. However, Mine Ventilation Optimization, (MVO) and integrating it with Ventilation on Demand (VOD) is only becoming more of a reality in the last seven (7) years. A systems approach to MVO takes into account all the elements from the point the power is distributed into the ventilation fans through to the actual quality and quantity of fresh air to the working face. Opportunities exist throughout the system for energy savings but not all of them are cost-effective. Depending on the application, these opportunities can be easily realized by properly sizing, streamlining, maintaining and operating the ventilation system using premium mine proven energy efficient components throughout. Implementation of VOD is a key step in achieving the MVO objective. However, VOD is a concept, and it requires various tools, procedures, and strategies for cost-effective and operationally viable implementations. This paper provides a historical background in the development of VOD and provides a framework for proper and cost effective implementation. In addition, an optimized ventilation system will also allow increased airflow by reducing resistances and shock losses. This turn in would allow production target improvement, which could be an attractive objective compared to energy savings. Mine ventilation is the life support system of an underground mine, and contributes to sustainable development and corporate social responsibility goals assuring health and safety aspects of strategic planning. The proposed framework addresses implementing mine ventilation optimization integrating ventilation on demand as a vehicle for energy, health and safety improvement and overall productivity gains in the mining cycle efficiency while significantly reducing carbon footprint of a mine.

Aug 1, 2013

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By G. E. Agar, R. Stratton-Crawley

"The applicability of a hydrocyclone model to simulation of the cyclone banks in a multi-stage sandplant circuit producing mine back fill has been demonstrated. The model ha~; been used in conjunction with a modular computer program for circuit simulation in order to study the effect of changes in the operating conditions. It has been shown that weight recovery to sand fill increases as feed percent solids decreases, and, to a lesser extent as pressure drop across the banks increases. An increase in apex diameter also causes an increase in weight recovery. Increased weight recovery must, however, be balanced against sump an1l cyclone capacity and dilution of sand fill by fines. The predicted results from circuit simulation were in good agreement with plant data.The model has been found to be applicable to widely different ores."

Jan 1, 1979

By D. L. Millar

The hydraulic air compressor (HAC) is driven only by water, held up by a dam, to create relatively low head (typically 10-20 metres), such that the developed hydropower is used to cause flow in openings deeper underground. Air is entrained in the water at the inlet to the sub-surface openings (an air to water volume ratio of 1:1 is reported to be optimal) and is compressed as it is carried along by the deepening water flow. At depth, and with lower water velocities arising from larger cross sectional area tunnels, air bubbles separate out of the water flow and are collected in a receiver space above the flowing water. Water, free of air, then passes back up a return shaft (up-pipe) and rejoins the river or stream flow. In principle, an HAC can produce any pressure and flow rate required, given large enough shafts and enough water supply with head sufficient to overcome frictional resistance in the sub-surface tunnels. Practically, as air solubility in water increases with pressure, HAC installations with depths greater than 100 metres may lead to higher rates of compressed air loss, without special separation measures. A modern HAC application for mine refrigeration and cooling is presented.

Aug 1, 2013

By S. H. Logan

The present discussions throughout the civilized world on the subject of gold for monetary purposes may seem due to general economic conditions during the past year. But for some years previously a small group of authorities had warned the world against the continued disregard of an equitable distribution of existing gold reserves, and had urged the necessity of keeping the supply of new gold equal to the monetary demand, which, according to world production and trade figures, increases on the average about 3 per cent per annum. In 1927, Sir John Aird, the President of The Canadian Bank of Commerce, stated that the United States could spare a billion dollars of the supply it then held, 4 ½ billion dollars. About a year and a half ago the Professor of Banking and Currency in the University of London, Mr. T. E. Gregory, said, "If the world finds it impossible to modify its habits so far as to make an organized effort to economize gold seem less Utopian, it must be prepared to pay for its bad habits, in this and other respects, by a possible loss of material welfare." These clear-cut statements were not heeded, perhaps for one reason because most countries were in the flush of prosperity, and making such great demands upon the mining fraternity for industrial materials as to distract attention, at least to some degree, from gold mining. Now the world knows it faces serious problems, first, of making? fully effective its present monetary reserves, which, although badly distributed, are as a whole ample for the needs of the present, and secondly, of preventing a shortage in the supply of new gold, one that may come within the next few years if the present sources of supply are not enlarged, and if there is no marked change in the technique of gold production.

Jan 1, 1931

By R. Binning

"Economic high density mineral reclamation and subsequent transportation of solids through a pipeline presents many formidable engineering problems.Mineral reclamation system design by theoretical formulas is almost impossible because solids composition, ie. concentration, velocity, moisture content, solid size, etc. can only be controlled within a broad pumping range.Traditionally this has restricted pumping to relatively dilute slurries whereas it is usually preferred, because of economic considerations to reclaim as high a concentration as possible.At Toyo/De-Velde Corp. we recognized these pumping limitations and began to develop and manufacture a range of standard and auxiliary equipment that would exceed these technical restrictions.MATERIAL RECLAMATION & PIPELINE INJECTIONTo minimize fluid usage and increase material reclamation efficiency we designed a submersible dredge mixing pump that uses most of its energy to pick up material from rest, mix it with fluid into a highly concentrated slurry then push it firmly into a pipeline.Where material is too compacted to be mined by the standard submersible mixer pump, auxiliary high torque self contained submersible excavators can be fitted around the periphery of the mixer pump. This is to facilitate excavation and break up of the compacted material into a slurry.High flexibility of this system can be achieved by combining the many equipment variations available into the most efficient format to fit individual site requirements.Whatever combination of equipment is selected, torque is nullified by counter rotating excavators against each other. This increases effective excavator/material bite torque but also allows mixer/excavator rig suspension by cable for deep water material recovery."

Jan 1, 1985

By Xiaolin Cheng, A. J. Sinclair

"Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeo chemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:<equation>where all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemico-mineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

By N. Moelans, I. Bellemans, K. Verbeken

In this work, we present a phase field model to simulate the facetted crystallization of Fe3O4 in a quaternary FeO-Fe2O3-Cu2O-SiO2 melt under different partial pressures of oxygen. An important focus in creating more realistic phase field models is the incorporation of the thermodynamic driving forces in multicomponent multiphase-field models by coupling to thermodynamic databases. The diffusion of FeO, Fe2O3 and Cu2O is considered. The ratio of FeO/Fe2O3 at the upper boundary is in equilibrium with the oxygen fugacity of the atmosphere, while conserving Fe. Two-dimensional simulations are performed with different varying oxygen fugacity in the atmosphere. For the considered composition range, the growth velocities of the spinel crystals increase with decreasing oxygen fugacity. INTRODUCTION Crystallization of silicate melts has its applications in geology, pyrometallurgy and glass making. In pyrometallurgy, the solidification of slags influences the freeze lining behaviour (Campforts et al., 2007) and the cooling of slag after tapping (Durinck, Jones, Blanpain, & Wollants, 2008). Modeling of silicate melt crystallization is frequently done on the macroscopic level, using thermodynamic equilibrium calculations to determine the fractions of all phases as a function of temperature. The Factsage software and database package (Bale et al., 2016, 2009, 2002) already proved its usefulness in pyrometallurgical applications, for example to model the phase mixture after solidification of a stainless steel slag (Durinck et al., 2008). Crystallization of phases typically results in complex morphologies on the mesoscale, e.g. dendrites or facetted growth. On this mesoscale, the phase field concept has proved to be a very powerful tool (Moelans, Blanpain, & Wollants, 2008) for modeling crystallizing microstructures, because it can treat arbitrarily complex interface shapes with minimal mathematical complexity. In contrast to macroscopic models, the diffusion profiles and crystallization kinetics can be described as well as the morphology of individual crystals. First, Kobayashi (Kobayashi, 1993) simulated a growing dendrite in a pure undercooled metallic liquid. Then, Warren and Boettinger (1995) simulated a dendrite in an isothermal system considering a binary alloy. The extension to multi-phase systems was done by Steinbach et al. (1996). This was further extended by Tiaden, Nestler, Diepers, and Steinbach (1998) to a framework with coupled diffusion and phase field equations in multi-component systems.

Jan 1, 2019