Search Documents

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021

By Anne Lemnitzer

Full-Scale cyclic field testing was performed on a 3x3 pile group consisting of nine cast-in-drilled-hole (CIDH) reinforced concrete shafts and a comparable single-shaft in order to investigate group interaction effects, derive p-y curves for reinforced concrete fixed head piles and to validate currently available p-multiplier models. The piles are identical in diameter of d=2 ft and were tested in similar soil conditions. The single pile as well as in three piles within the pile group were instrumented with internal sensor instrumentation to record pile curvatures. External instrumentation was used to control and measure the lateral displacement of the specimens. Experimental studies were supported with analytical models to enable comparisons and offer design recommendations. All test specimens were tested to structural failure and group interaction factors ranged between 0.8 at small displacement levels and increased towards unit near structural failure. A set of p-multipliers was found to reproduce an accurate fit to the available test data.

Jan 1, 2010

By Mohammed Faizal, Abdelmalek Bouazza

"The operation of ground source heat pumps combined with foundation piles can have an effect on the thermal behaviour of the pile and the surrounding soil. This paper presents the effects of continuous heating, continuous cooling, and alternate heating and cooling operations on ground and pile temperatures as well as the thermo-mechanical behaviour of a field scale energy pile. The effect of pile operation on the ground temperatures is highest near the pile and reduces with increasing radial distance. The results of the present studies generally showed that the thermal elasticity of the pile is not affected.INTRODUCTIONGeothermal energy piles are foundation piles used as underground heat exchangers to maintain thermal comfort in buildings, via the use of ground source heat pumps (GSHPs). Ground source heat pumps are more economical and environmental friendly compared to conventional heat pumps. Energy piles can be combined with supplemental surface heaters or coolers, known as hybrid systems, for forcefully recharging the ground during non-operational times of the GSHP. Alternative heating and cooling of the GSHP improves geothermal energy usage and alleviates heat build-up in the ground and provides a balance of ground temperatures around the heat exchanger (Jalaluddin and Miyara, 2012).The temperatures induced in the piles during GSHP operation can lead to a complex response of thermal strains and stresses in the pile concrete. An assessment of the thermo-mechanical response of energy piles for various thermal loads may assist engineers in the design process. Furthermore, an assessment of ground temperatures will also highlight any potential thermal interactions with other energy piles in actual building operations.At present, the thermal strain and stress distribution in field scale energy piles has mostly been studied for continuous operation (Laloui et al., 2006; Bourne-Webb et al., 2009; McCartney and Murphy, 2012; Akrouch et al., 2014; Mimouni, 2014; Murphy and McCartney, 2014; Murphy et al., 2014; Wang et al., 2015). These studies have contributed considerably to the understanding of the axial thermal strain and stress distributions in the piles and have shown that pile thermal behaviour is mostly thermo-elastic without inducing major structural concerns.The present paper adds to the current knowledge by assessing the pile thermo-mechanical and ground thermal response for continuous and alternating thermal loads of a field scale energy pile. The operation modes studied are 24 hours continuous cooling (Faizal et al., 2015), 24 hours continuous heating, (Wang et al., 2015) and alternate heating and cooling operation (Faizal and Bouazza, 2016). The forced ground thermal recharging is done during the non-operating times of the cooling unit, simulating a solar hybrid GSHP system for a scheduled intermittent mode of operation."

Jan 1, 1900

By Roberto A. Lopez, Eric Lindquist, Jon Bussiere, Dean Iwasa

"The new 11-story U.S. Federal Courthouse building in downtown Los Angeles demanded a cost effective foundation system capable of attaining a strict total settlement criterion of 0.5 inches (12 mm) under high applied loads. A design-build ground improvement system consisting of 3 ft (0.9 m) and 7 ft (2.1 m) diameter deep soil mix (DSM) columns embedded into the relatively soft Fernando Formation bedrock was selected for the project. The DSM columns support applied stresses of up to 8,800 psf from four large concrete core elements that transfer concentrated building loads to a 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat. The soil mixing ground improvement solution provided flexibility by allowing installation of the DSM columns around existing belled caissons left in place from prior structures, and by allowing repositioning of some of the DSM columns to avoid other existing obstructions in the fill. DSM spoils were used to construct a 2 ft (0.6 m) thick load transfer platform on top of the DSM columns. Quality control measures included utilizing equipment outfitted with automated data acquisition systems, performing three full scale load tests, performing daily wet-mix sampling and compression testing, performing full-depth coring and unconfined compression testing on core samples, and using a borehole acoustic televiewer to evaluate the uniformity of the DSM columns where core recovery was problematic. The results of subsurface investigation and the load tests were used to develop 3-dimensional finite differences models for evaluating stress distribution and deformation of the foundation system.INTRODUCTIONThe new U.S. Federal Courthouse building is currently under construction in downtown Los Angeles, California. The new courthouse will be 11 stories tall with one partial below-grade B1 basement level. The building will have four structural core elements that extend from the main building foundation at the B1 level to the top of the structure. The majority of the building loads will be transferred through the structural core elements to a new 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat beneath the central portion of the structure. The foundation pressures beneath each of the core element locations will be approximately 6,200 to 8,800 psf (300 to 420 kPa) with lower foundation pressures at locations farther away from the central core area."

Jan 1, 2015

By J. Erik Loehr, Minh Uong, Andrew Z. Boeckmann, Sarah G. Myers

"The University of Missouri performed a lateral load test program involving 32 drilled shaft load tests for the Missouri Department of Transportation (MoDOT). Tests were performed at two MoDOT geotechnical research sites, and all shafts were founded in shale. Shafts were instrumented to measure the displacement of the shaft head, and the structural response of each shaft was interpreted from strain gage data and from ShapeAccelArray (SAA) data. The SAA is a chain of rigid segments with sensors that use MEMS (microelectromechanical systems) technology to measure the tilt of each segment/joint. The measuring principle of the SAA is therefore similar to that of an inclinometer. The SAA device was placed in a casing installed in the center of each test shaft to provide a continuous record of deflection along the length of the shaft throughout each test.Bending moment profiles were calculated from strain gage data and from SAA data. Interpretation of bending moments from measurements of strain (via strain gages) and displacement (via SAA) is a nontrivial exercise, primarily because the bending stiffness, EI, is nonlinear and greatly influenced by concrete cracking, which is difficult to predict. The procedure used for this work predicted values of bending stiffness along the length of the shaft as a function of the bending curvature, which was interpreted from the SAA data. Values for bending stiffness as a function of curvature were computed using Ensoft LPile v2012. Bending moment profiles from SAA data were typically similar to those from strain gage data. The SAA bending moment profiles were often “noisier” than the strain gage bending moment profiles, but the SAA bending moment profiles had more data points since the SAA chain was continuous from the top to the bottom of each shaft."

Jan 1, 2017

By Richard E. Sylwester

Evaluating surface and subsurface conditions for marine foundations (bridges, causeways, terminals, etc.) is often done with a limited amount of data. Subsurface information for these projects is primarily acquired using traditional methods, such as boreholes, test pits or divers, which tend to be expensive and limited in the area of coverage. A number of geophysical methods, including precision bathymetry, sidescan sonar, and seismic reflection or subbottom profiling are extremely cost-effective and obtain significantly more data than can be acquired using traditional intrusive methods. These geophysical methods provide detailed surface images and continuous profiles of the subsurface stratigraphy. This information can be invaluable for selecting the best location for geotechnical boreholes and to map potential geohazards such as submarine slides and filled or open scour holes. Offshore investigations conducted for a proposed highway bridge (Knik Arm Bridge, Cook Inlet, AK), the retrofit of two existing bridge (Antioch and Dumbarton Bridges, CA) and a proposed cruise ship terminal (Ketchikan, AK) used a combination of geophysical methods to map water depth, detect and map debris on the seabed, map the thickness of unconsolidated sediment, determine the depth to bedrock and identify potential geohazards such as scour holes. The results of the geophysical investigations will be used to select locations for obtaining geotechnical borings, to extrapolate geologic information between existing or proposed boreholes, evaluate the potential depth of scour and design a pile support pier. Geotechnical engineers, offshore contractors and bridge designers are realizing the importance of the early use of offshore geophysics for (i) site characterization, (ii) to reduce the uncertainty of geotechnical conditions thus avoiding designs that may be overly conservative and thus more expensive and (iii) to assist in selecting locations for geotechnical borings.

Jan 1, 2013

By Manasi Wijerathna, D. S. Liyanapathirana

"Deep cement mixing is a popular soft ground improving technology that improves the bearing capacity and settlement characteristics of natural soil. When Deep Cement Mixed (DCM) columns are installed attached to each other in a wall configuration, the walls are capable of resisting bending moments and shear forces in the direction transverse to the columns. Therefore, installing DCM walls beneath the embankment slope perpendicular to the alignment of the embankment is a proper solution to prevent excessive lateral deformations of the embankment. Previous research studies have shown that failure patterns of DCM column walls are different to failure patterns of individual DCM column rows, under lateral loads. This study investigates the failure patterns of embankments where DCM column walls are located beneath the slopes, with respect to DCM wall strength, DCM column wall width and the spacing between DCM walls. 2D and 3D numerical models developed using the ABAQUS/standard finite element programme, were used in this investigation. Results show that the DCM wall strength and width of the DCM wall have a significant influence on the failure mode and the critical failure surface of the embankment. 3D simulation results demonstrate that the failure due to soil extrusion between columns was less pronounced in embankments improved with DCM walls, due to the interaction between the DCM walls and the surrounding natural soil.INTRODUCTIONEmbankments constructed over soft ground are highly susceptible to global slope failure and excessive displacements due to combined effects of vertical and lateral loads beneath the embankment slope (Zheng et al., 2009, Han and Gabr, 2002). The overall stability of the embankment can be significantly improved by improving the soil beneath the slope of the embankment using Deep Cement Mixed (DCM) column rows or overlapped DCM column walls (Jamsawang et al., 2015, Larsson and Broms, 2000, Topolniki, 2004, Broms, 1999). According to the literature, the improved ground experience different failure modes other than shear failure, such as separation of columns, overturning, shear failure along the columns or dowel action (Broms, 1999). Some of the failure modes reported by Broms (1999) are shown in Fig. 1. The ultimate failure mode depends on the geometry and the strength of the improved ground (Jamsawang et al., 2015, Kitazume and Maruyama, 2006, Kitazume and Maruyama, 2007)."

Jan 1, 1900

By Tracy Brettmann

The Highway 146 Bridge Expansion Project across the Clear Creek Channel in Houston, Texas was designed on driven precast concrete piles. However, during construction, the piles along one side of the bridge along the main channel encountered obstructions and couldn’t be installed. These obstructions turned out to be the remnants of a previous bridge foundation at this location, which was unknown to the designers since that bridge had been demolished 40 years ago. Those old foundations were massive 20 ft by 40 ft (6 m by 12 m) pile caps 11 ft (3.3 m) thick supported on precast concrete piles 37 to 55 ft (11 to 17 m) long. The foundation re-design for these locations involved installing a single 78 inch (2 m) diameter drilled shaft up to 125 ft (38 m) long to replace the originally planned driven pile supported pile cap. The drilled shafts would need to be installed within very tight tolerances since they were supporting a single bridge column directly above it. In addition to drilling through the obstructions, this work would need to be completed from barges in 30 ft (9 m) of water capable of dealing with both the current and tides affecting this area. The shafts were installed using a multi-step process. The first step involved coring a larger diameter 100 inch (2.5 m) hole through the reinforced concrete pile cap and removing the concrete inside. This was followed by the installation of a 72 ft (22 m) long permanent casing to and removing the soil and existing precast piles inside. Finally, the drilled shaft excavations were advanced to the completion depths (uncased) using bentonite slurry as the support fluid.

May 1, 2022

By Mu Chen, Ye-Shuang Xu, Dong-Wei Hou, Shui-Long Shen, Huai-Na Wu

"This paper presents a laboratory investigation on the mechanical behaviors of the cement-clay admixture improved by polypropylene fiber. Cement can significantly improve the clay admixture. The fiber additive also improves the strength and ductility of the improved clay. The Unconfined Compression Strength (UCS) of the polypropylene fiber-reinforced cement-clay presents an overall trend to grow with the increase of fiber length. The improved clay reached its peak strength at the fiber content of 0.5%. Then the UCS of the improved clay will slowly reverse if the fiber content continues to rise. For study of curing time, improved clay behaves better in its early strength, but an inhibition will be brought about if fibers are excessive.INTRODUCTIONGround improvement technology is essential for construction of structures in soft ground. Some traditional techniques often cost much but result in little. For instance, along the coastal region of China, soft ground is often improved by backfill with high quality sandy soil transported far away, leading to high additional haulage costs and long construction period. Reutilizing the excavated soil as backfill or subgrade after treatment, by contrast, will be more economical and effective (Hufenus et al., 2006). Many researches have been conducted to improve the compression strength of soft soil, among which, the method of mixing the soft soil with cement and fly ash is one of the most common ways (Kolias et al., 2005; Horpibulsuk et al., 2009; Porcino et al., 2012). It is known that soil resists well against compression and shear force but behaves poorly in resistance to tension. Therefore, utilizing tensile elements such as fibers and strips to improve the tensile strength will be effective because of its strength isotropy, better durability and cost effective (Haeri et al., 2000; Kaniraj and Havanagi, 2001; Consoli et al., 2010)."

Jan 1, 2015

By Anupam Saxena

This paper presents a case history of design, prediction, probe and production pile driving monitoring, loading test, and installation of piles for a 22-story condominium tower in southwest Florida, U.S.A. ASC was commissioned to provide value engineering services in the proper selection of an economical and satisfactory foundation system. For the site-specific subsoil conditions, various types of foundations were considered and following an evaluation of high structural loads, site-specific constraints, and the production timeframe mandated by the project owner, a prestressed concrete pile-supported system was selected as an economical and effective foundation approach. The building foundations were designed for a compression capacity of 575 kN (65 tons) for the tower and 220 kN (25 tons) for the parking structure. The axial pile capacity and lengths were predicted using SPT91 software. The validation of these capacities was derived from driving 21 probe piles and performing static loading tests on selected probe piles (2 in compression and 1 in tension). The predicted pile capacities were evaluated with results from static loading tests on selected probe piles. This information was effectively utilized as part of an overall quality control program to install a total of over 920 prestressed concrete piles to lengths ranging from 11.5 to 16.5 m (37 to 54 ft) below existing ground elevation as part of the foundation support system.

Jan 1, 1996

By Ronaldo Luna, Donald Deardorff

"The use of load and resistance factor design (LRFD) is well documented since the 1960s for structural applications when it was first adopted into the American Concrete Institute Building Code in 1963 and was established for geotechnical applications by the Danish Geotechnical Institute about the same time under the name of Limit State Design (LSD).The Federal Highway Administration required all federally funded projects to use the LRFD method by 2007. Due to this funding requirement, recent LRFD research for geotechnical applications has focused on common bridge foundations (i.e., driven or drilled shafts), resulting in good documentation for design using these methods. Unfortunately, the practicing geotechnical engineer does not intuitively know how to create resistance factors for deep foundations systems that have design methodologies and installation techniques significantly different from driven or drilled shaft foundation systems.Helical anchors typically use semiempirical methods for preliminary capacity design and a torque correlation methodology during installation to verify required capacity. Here we provide basic information on the LRFD methodology for helical anchor design. Additionally, the First- Order Second Moment (FOSM) method is applied to a previous helical anchor study (Hoyt and Clemence 1989) to determine resistance factors for an ultimate tension capacity strength limit state.MethodologyThe concept of the LRFD method is to establish factors for both the load and resistance that account for uncertainties using probability theory. The factors increase the nominal load and/or decrease the nominal resistance such that the probability of failure is an acceptable value. LRFD also accounts for the effects of load combinations (dead, live, seismic, wind, etc.) by determining the probability of the combined occurrence. The general form of the LRFD equation used by American Association of State Highway and Transportation Officials (AASHTO) is:"

Jan 1, 2009

By J. Gniel, L. King, C. Gaudin, C. O’Loughlin

"This paper presents some recent advancements in centrifuge modelling, which enable the installation of displacement piles to be performed in-flight while measuring ground responses. Details and results are provided from a series of experiments where 21 full-displacement piles were installed into a sample of consolidated kaolin clay at 40g. The piles were pushed into the sample at a constant rate of penetration, with installation reaction loads and pore pressures measured. Insight into the installation effects of the full-displacement piles was obtained by undertaking in-situ testing pre- and postinstallation of piles. The findings show that centrifuge testing has the potential to play an important role in furthering the current understanding of displacement pile behaviour and installation effects.INTRODUCTIONDisplacement piles and displacement ground improvement columns cause soil to undergo significant distortion and shearing during installation, which alters the soil properties. It is essential to consider these changes in soil properties to estimate the behaviour of pile foundations with higher degree of accuracy. However, the installation effects of displacement piles are widely considered as one of the most difficult geotechnical mechanisms to model, both analytically and numerically, and experimental data is needed to advance the current state of knowledge.Theories, analytical and semi-analytical, have been developed to describe the displacement pile installation process. Randolph et al. (1979) applied the cylindrical Cavity Expansion Method (CEM) to model the installation of a displacement pile in a fine grained cohesive soil. However, cylindrical CEM only considers the field variables in radial coordinates, and hence the soil-pile interface can only be modelled as a frictionless material. Baligh (1985) introduced the Strain Path Method (SPM), which assumes soil flows around the tip of a displacement pile. SPM was shown to model the stress and strain fields, particularly within close proximity to the pile, more accurately compared to the cylindrical CEM. While these methods account for the installation effects of a displacement pile and can be used to estimate a resulting ultimate bearing capacity, they are unable to describe the load-settlement behaviour of such piles. With the added complexity of group effects, existing analytical methods do not provide a means to accurately calculate the ground response to the installation of a group of displacement piles in a cohesive soil.The advancement of computational power, numerical techniques and constitutive models has improved the accuracy of numerical analysis, particularly in regard to modelling pile installation. However, even with advanced techniques, Finite Element Method (FEM) suffers a number of disadvantages due to the large deformations, which results in mesh distortion and tangling. Mesh-free methods such as Discrete Element Method (DEM), Smoothed Particle Hydrodynamics (SPH) and Material Point Method (MPM) are the next generation of computational techniques that are able to deal with large deformation problems. However, these advanced techniques are computationally expensive, complex and yet to be incorporated into commercial packages. Such methods are considered to still be in the development stage and are yet to provide a complete solution to pile installation problems."

Jan 1, 1900

By Amr M. Sallam

A case history of utilizing a mat foundation enhanced with ?settlement-control? piles to support a high-rise building in Downtown Orlando is presented. Original geotechnical engineering studies, performed by others, recommended pile foundations due to difficult soil conditions and highly variable loads. The value engineering study performed by the authors provided alternative foundation system of the mat foundation enhanced by ?settlement-control? piles. The alternative foundation system required few iterations of structural and geotechnical analysis. A target stiffness for the settlement-control piles was selected by the structural engineer. Pile load tests were performed to verify the recommended pile geometry. A total of 81 auger-cast-in-place settlement-control piles 45-foot long 16-inch diameter were installed. A total of 24 columns were monitored for settlement, which showed substantially less settlement than predicted. It is the authors? opinion that the ?settlement-control? piles increased the mat stiffness, relieved the concentration of contact pressures around heavily loaded columns, and reduced potential differential settlement. Mat foundation with settlement-control piles provided border-line foundation solution between shallow and deep foundations and has the potential to be widely used in Central Florida for similar subsoil and loading conditions; however a thorough analysis using three dimensional Finite Element Modeling may be needed to refine the geotechnical evaluations.

Jan 1, 2009

By K Ilamparuthi, R. K. Madhumathi

"This paper presents the results of 1g model tests conducted on model piles both single and two pile groups embedded in sand by physically inducing lateral soil movement. From the test results it was found that the pile with higher L/D ratio exhibits higher deflection in case of pile embedded in medium dense sand whereas in loose sand the response is vice versa with higher deflection for the pile of lesser L/D ratio. The induced bending moment in piles is more for longer piles than shorter piles irrespective of the density of sand bed. It is also found that the pile head deflection and the bending moment are found to decrease exponentially with increasing distance between the pile and the wall. For pile group arranged in a row parallel and perpendicular to retaining wall, the deflection of single pile is more than the deflection of two pile group irrespective of the depth of excavation for spacing of piles tested. The influence of soil movement on the lateral response of pile is also analyzed through 3-dimensional finite element analysis. The numerical results thus obtained are validated with the results of experiments. The Mohr-Coulomb material model adopted to represent the soil behaviour predicts the response of pile reasonably and compares well with the experimentally observed response.INTRODUCTIONPile foundations are adopted to support structures such as foundations of high rise buildings, transmission towers, offshore platforms, bridge abutments etc., when good bearing stratum is not present at shallow depth to bear the loads of these structures. In the recent past particularly in the urbanized areas structures are built close to one another and nearby excavation will cause a reduction of lateral earth pressure and soil movement behind the retaining wall (Ong, 2004). The reduction in support stress will induce additional movement to the pile and leading to distress in pile foundations located adjacent to supported excavation. In these situations understanding the response of piles next to supported excavations becomes essential.The behavior of piles subjected to soil movement was studied by Poulos and Chen (1996 and1997) through tests on 1g models and the findings concluded that the maximum bending moment was found to decrease with decreasing pile diameter and decreasing pile spacing . Leung et al. (2000 and 2003) studied the effects of excavation induced soil movement on pile foundations in sand through centrifuge tests and established that the restraints on the pile head would cause additional shear force and/or bending moment at the pile head, although the restraints help to reduce the pile head deflection/rotation. In the theoretical studies of Poulos & Chen (1997), boundary element method (PALLAS) was used for analysing the pile subjected to lateral soil movement and charts were proposed for designing the piles. Pan et al. (2002) and Miao et al. (2006) analysed the passive pile behavior through three dimensional finite element analyses. However research works reported on piles subjected to lateral soil movement are limited."

Jan 1, 2015

By Antonio Kodsy, Lutful Khan

A research was carried out to test the possibility of reducing the pullout resistance of metal sheet piles driven in clay soils using Electrokinetic (EK) conditioning. The hypothesis was applying an electric gradient for a certain period of time should reduce the adhesion between the clay soil and the sheet piles. Tests were conducted on bench scale thin stainless-steel metal plates embedded in pure kaolinite clay, and mixtures of kaolinite clay and sand. The pullout resistances were determined after 20, 40, and 60 minutes residence times of steel plates in the soils before and after EK conditioning under an electric gradient of 1500 V/m. In kaolinite clay, the pullout resistance showed linear reduction with the duration of EK conditioning and about 60 % reduction in pullout resistance was observed after 60 minutes EK conditioning. For the kaolinite-sand mixtures, the pullout resistances were reduced by about 70% and 80% for 20% and 30% sand contents respectively after 20 minutes EK conditioning and showed no significant improvement with the increase in conditioning duration. It was concluded that the proposed electrokinetic conditioning process could potentially reduce the pullout resistance of metal plates embedded in clay and clayey soils. SHEET PILE WALLS Sheet pile walls are typically used at waterfronts as retaining structures or during the construction phase to shore the soil and avoid collapse of the excavations. When used as permanent structures, sheet pile walls are not removed after the completion of the project. However, as temporary support, they are extracted after the completion of the project and reused. In pure clay soils the extraction processes often becomes a challenge requiring very large pullout forces which could damage the sheet piles. There is a research need for developing an efficient method of sheet pile extraction from clay soils addressing the issue of pullout force reduction. However, very few researches have been conducted regarding the extraction techniques of sheet piles and their economic effect on the cost of a project. In this study a novel method for reducing the pullout resistance of sheet piles in clayey soils using electrokinetic conditioning was explored. The hypothesis of this research is that the electrokinetic process in soil/water system, specifically electrophoresis and electroosmosis, could be used to loosen the sheet pile walls embedded in cohesive soil and hence reduce the required force of extraction. The aim of this study was to test this hypothesis through laboratory tests carried out on steel plates embedded in cohesive soil samples. The pullout forces of the steel plates before and after varied duration of electrokinetic (EK) conditioning were evaluated and compared. The process was also investigated for clay-sand mixtures.

Jan 1, 2019

By A. B. Cerato, M. K. ElSawy, A. Elgamal

"Helical piles are gaining popularity as foundations for new construction as well as retrofitting option for deficient foundations. More recently, large diameter helical piles are used to support structures in regions characterized with high seismic hazard. Even though they have proven to be viable in seismic areas such as New Zealand, where they experienced little damage during the Christchurch earthquake, the knowledge about their seismic analysis and performance is largely lacking. Therefore, there is a need for comprehensive study to evaluate their performance under seismic loading. The current objective of this study is to investigate the performance of helical piles through a full-scale testing program that was performed at the NEES/UCSD Large High Performance Outdoor Shake Table (LLHPOST). The experimental setup involved ten steel piles of different configurations installed in dry sand. The piles were loaded with different masses and were subjected to different earthquake signals to simulate different dynamic behavior. This paper compares the performance of different moment curve fitting methods used to interpret the test data. Furthermore, the effects of different frequency content of loading on the pile response is illustrated in terms of deflection along the shafts of tested piles with different configurations.INTRODUCTIONEarthquakes are a major hazard for structures situated in seismic regions, and dynamic loading must be a design consideration. Successful design of a foundation system entails providing a safe and economic foundation solution to resist earthquake loading. Different foundation options have been used to support buildings in high seismic regions. Helical piles represent a viable foundation option that offers several advantages in terms of ease of installation, lower cost and environmental impact, ability to approximate the axial capacity directly from torque readings and more (Perko 2009). However, they are not typically considered as an option in many seismic regions. Meanwhile, several buildings supported on helical piles in New Zealand have survived the Christchurch earthquake with negligible damage, which encourages performing further research to understand the behaviour of these piles under seismic loading.A helical pile consists of a steel shaft fitted with a steel helix/helices. The helical pile is installed by applying torque to its head via mechanical torque. Nowadays, helical piles are used in a wide range of applications such as foundations for light posts and residential houses. The static behaviour of helical piles has been studied extensively and is relatively well understood (Tsuha and Aoki 2010; Mittal et al. 2010; Sakr 2011; Elsherbiny and El Naggar 2013; El Sharnouby and El Naggar 2012; Elkasabgy and El Naggar 2015; Weidong et al. 2015 and Bagheri and Naggar 2015) However, the dynamic and seismic behaviours of helical piles is seldom investigated (Elkasabgy and El Naggar 2013). This underscores the knowledge gap currently present regarding the seismic behaviour of helical piles."

Jan 1, 2017

By Joshua C. Adams, Les Chernauskas, Edward L. Hajduk

"Drilled shafts are increasingly being used to support bridge and building foundations. Because these foundations usually carry very high design loads and often serve as non-redundant, single load carrying units, these foundation systems need a high level of quality control (QC) and quality assurance (QA) during construction. One such method for providing QC/QA is crosshole sonic logging (CSL) testing, in which ultrasonic signals sent across the drilled shaft concrete assess concrete quality.CSL testing is an effective tool to evaluate the integrity of the in-place drilled shaft concrete. While typically used to evaluate drilled shaft concrete after construction, CSL testing can also be used to evaluate drilled shaft repairs. This application can be difficult, given the variability of repair methods and material properties. CSL testing can also be adversely affected by the condition of the concrete/access tube bond, leading to false anomaly detection and/or inability to evaluate concrete integrity effectively. This phenomenon, called access tube debonding, is often located in upper portions of the drilled shafts where large changes in groundwater occur, such as within tidal zones.Two case histories showcase innovative uses of CSL testing to deal with consistent access tube debonding and to evaluate drilled shaft repairs.CSL OverviewCSL testing involves placing ultrasonic transmitters and receivers in access tubes installed in the drilled shafts prior to concrete placement. Concrete quality is assessed by examining the First Arrival Time (FAT) and relative energy of the signal sent between the transducers. If the distance between the access tubes is known, an apparent signal velocity (i.e., wave speed of the ultrasonic signal through the concrete) can also be determined and used to assess concrete quality.Common CSL testing practice consists of simultaneously raising the ultrasonic transmitter and receiver and recording the ultrasonic signals with respect to depth. This results in a 2D examination of the"

Jan 1, 2009

By Masaki Kitazume

"Many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction which occur in a loose and saturated sand layer, induces quite large damages of infrastructures, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Many kinds of ground improvement techniques based on various improvement principles have been developed for earthquake disaster mitigation. Among them, the grid type deep mixing method has been often applied to liquefaction mitigation. In the method, the stiff grid walls are constructed by mixing the soil and binder in-situ, which are expected to restrict the shear deformation of the soil within the grid walls so that the pore water pressure generation can be remained small. The high applicability of the method was confirmed in several earthquakes, including the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake. In this paper, the development of the method, some applications of the deep mixing method to earthquake disaster mitigation are briefly introduced. INTRODUCTION In Japan, many earthquakes take place every year in Japan, in which the 1995 Hyogoken-Nambu earthquake and the 2011 Tohoku earthquake induced both a humanitarian crisis and massive economic impacts. As liquefaction induces quite large damages, the importance of liquefaction mitigation has been emphasized to minimize earthquake disasters for many years. Table 1 shows the amount of damage to port facilities (Noda, 1991). According to the table, the amount of damage when liquefaction takes place is about 20 to 50 times larger than that without liquefaction. This highlights the importance of liquefaction mitigation to minimize earthquake disasters. There are many kinds of soil stabilization techniques developed for liquefaction in Japan. Among them, the deep mixing method (DMM), an in-situ cement stabilization techniques, was developed in 1970s in Japan and has frequently been applied to improvements of clayey and sandy soils (Kitazume and Terashi, 2013). The grid type DMM has been often applied to prevent liquefaction, where the grid of stabilized column walls function to restrict generation of excess pore pressure in the soil within the walls by confining the soil particle movement. The improvement effect of the method was first evaluated in the Hyogoken-Nambu earthquake in 1995 and was also evaluated in the Tohoku earthquake in 2011. In this paper, some successful performance of the deep mixing method to earthquake disaster mitigation in the two earthquakes are briefly introduced."

Jan 1, 2015

By Kaustuv Bhattacharya, Manish Kumar, Nirbhay Singh, Prodyot Kr. Ray, Praveen Soin

This paper highlights salient features of an excavation 38 m (Length) by 10 m (Width) by 24 m (Depth) carried out in Central Kolkata. Secant pile wall (SPW) formed using a combination of alternating 1200 mm & 800 mm diameter piles was used. Six layers of struts and waler beams, including bottom slab were utilized as lateral restraints to piles. The geotechnical profile for excavation zone was predominantly silty sand to sandy silt. The profile is characteristic of river channel deposit usually encountered in Kolkata. Temporary stage analysis (including seepage analysis) and design were carried out in FEM softwares. Design checks for clay bursting, piping, bottom heave, etc. were also carried out. Extensive instrumentation and monitoring were carried out during the excavation period to check parameters such as ground movement, pile movement, piezometric heads, etc. as per review levels. During excavation, ground improvement using Tube-a-manchette grouting technique was also required to be carried out as per field observations. The paper discusses some of the major challenges faced as well as measures taken to counter them, during deep excavation carried out in silty soils in a very congested Urban setting in the heart of a Megacity.

Sep 1, 2022

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005