Search Documents

By D. L. Albright, R. W. Kraft

High-purity materials have been used in producing as-cast, controlled, colony, and degenerate solidification structures in the Fe-FeS eutectic. Experiments disclosed that this eutectic can be classified as normal and has a natural morphology composed of rodlike iron particles dispersed in a matrix of iron sulfide. The metallography of the various structures was studied, and a preferred crystallography was revealed in the controlled specimens produced by unidirectional solidification. The orientation effects found in these latter specimens are an [001] fiber texture in the -mowth direction of the bcc iron bhase and a texture corresponding to bicrystalline behavior in the hexagonal iron sulfide, with the growth direction near to (2111) poles. The observed texture of the iron phase is considered as indirect evidence that the alloy un-dercooled by at least 75°C before solidification. The unidirectional solidification of binary eutectic alloys has produced materials which exhibit a structure and properties markedly dependent upon the solidification process. In many cases a controlled microstructure with pronounced metallographic and crystallographic anisotropy can be experimentally achieved by proper regulation and balance of the growth rate of the alloy, the chemical purity of the starting materials, and the thermal gradient in the liquid at the liquid-solid interface. The purposes of this investigation were to produce various micro-structures in the Fe-FeS eutectic for subsequent study of their magnetic properties and to correlate the different structures with the solidification conditions in order to obtain a better understanding of the structure of eutectics. The Fe-S equilibrium diagram exhibits a eutectic composed of nearly pure iron and stoichiometric iron sulfide (FeS1.00), with the eutectic reaction occurring at 988°C and 31.0 wt pct S.1 Calculations indicate that this eutectic should solidify with about 9.5 vol pct Fe and 90.5 vol pct FeS, which in turn suggests2 that the micros tructure will consist of a rodlike iron constituent dispersed in a matrix of FeS. This characteristic has in fact been revealed some years ago.3 Thus, controlled solidification of this alloy might yield a material whose micromorphology would consist of very small ferromagnetic iron particles, rod-like in shape and aligned parallel to one another, supported in a matrix of antiferromagnetic FeS. Such specimens, because of the magnetic characteristics of the two phases, would be interesting subjects of study as magnetic materials. Hence the magnetic properties were considered in detail and are reported elsewhere.4 EXPERIMENTAL PROCEDURE The specimens of Fe-FeS eutectic were prepared from ultrapure iron (99.99+ pct) and high-purity sulfur (99.999+ pct). The iron was estimated to contain 60 ppm impurities (99.994 pct Fe) after zone purification.5 The ingots of iron were cut into chips, and the lumps of sulfur were ground into powder. In order to redice any nometallic impurities which might have accumulated during handling, the iron chips were annealed for 5 hr at 750° ± 10°C in a dry hydrogen atmosphere. Immediately after this treatment the chips were blended with the sulfur powder in eutectic proportions; the mixture was tamped into transparent fused quartz tubing and then vacuum-encapsulated under a pressure of 40 to 60µ of Hg. Because FeS expands upon solidification it was necessary to re-encapsulate the initial capsules so that oxidation reactions would be avoided when the inner tube cracked during solidification. For purposes of homogenizing the blended mixtures before solidification, the double capsules were heated to 750° ± 20°C and held for 20 hr; after this treatment the reacted product was weakly agglomerated. Each sample was then loaded into an apparatus for very rapid melting and freezing; this was accomplished by passing a molten zone through the specimen, using induction heating and a traverse mechanism. The resulting specimens solidified in the shape of the quartz tubing. Two sizes of specimens were used in this work, 18 mm diam by 100 mm long and 5 mm diam by 30 mm long. Metallographic examination of several ingots of both sizes after the above consolidation indicated no lack of compositional homogeneity and a random "as-cast" structure, because the travel rate was so rapid that unidirectional solidification was not achieved. Unidirectionally solidified specimens were resolidified in the apparatus shown schematically in Fig. 1, This equipment consisted of a kanthal resistance furnace mounted on the carriage of a zone-melting unit so that the heating element could traverse the length of the sample at a selected rate of speed. Large specimens were solidified with the mechanism tilted at ap-

Jan 1, 1967

Established as a Division November 17, 1948 B W Gonser, Chairman J C Kinnear, Jr, Past Chairman H H Kellogg, Chairman-Elect R C Cole, Vice-Chairman, '58 A E Lee, Jr, Vice-Chairman, '59 W R Opie, Vice-Chairman, '60 R W Shearman, Secretary AIME, 29 West 39th Street New York 18, N Y

Jan 1, 1957

By Charles W. Goodale

The attention of the Institute has been called by Prof. John A. Church* and Mr. W. Lawrence Austin? to the free-milling ores of the Tombstone mines and their treatment, but the silver-bearing man ganese ores of the district have received only a passing notice. As these ores show some interesting peculiarities, and have yielded not less than 750,000 ounces of silver, they are worthy of some study. The Knoxville, Lucky Cuss, Luck Sure, and Wedge mines (named in the order of their importance) are situated along the northern border of the district. They have been the leading producers of this manganese ore, and possess the same general characteristics. Special attention will be given to the Knoxville, as it has been the one most extensively developed. The limestone belt, in which the Knoxville ore bodies occur, has an easterly and westerly trend, is about 1680 feet wide, and rests on granite on the north, the plane of contact being nearly vertical. It is overlain by quartzite, the contact-plane having a dip of 82°. Some mining has been done along these contacts, and a considerable amount of pay ore has been extracted, but development has been very superficial. The ore found along these contact planes contains very little manganese, and differs entirely from the ore in the lime stones. No attempt will he made to assign this limestone country-rock to a particular geological horizon, as no fossils have been found in it. Prof. Blake, in a paper on "The Geology and Veins of Tombstone, Arizona" (Trans., x., 334), speaks of the middle and upper strati-

Jan 1, 1889

By Dick Whittington, W. R. Taylor

GENERAL In mid-1974, a representative of ARCO Petroleum Company walked into our Austin offices and asked for a permit for ARCO's first Clay West Mine site. This was the first in situ uranium mining permit issued in the United States. That initial permit, issued in January 1975, was for three acres. The four years since have been characterized by growth and change. Today there are 16 permits approved for approximately 1,540 production acres issued to five companies at eight sites in four counties. There are approximately seven additional permit applications being processed or on the verge of being submitted for an estimated 2,000 additional acres of production. As a rough gauge of the financial scope of this activity, at the typical 40 production wells per acre and an estimated $2,000/well, operators hale installed or committed $122 million for production wells. This does not account for the exploration and development wells installed to delineate the ore or the cost of processing facilities for extracting the uranium. HISTORY OF URANIUM MINING IN TEXAS Information I have concerning early in situ uranium mining activities is "sketchy" but the apparent first on-site test of in situ uranium mining was conducted between 1967 and 1971 at the Dueterstat site, north of Yorktown in Gonzales County, by City Service. Others ran tests at the Bruni site in Webb County and the Burns and Clay West sites in Live Oak County in the mid-70's. During this period, Texas Water Quality Board personnel in the central and district offices maintained a general surveillance of these various test activities. Regulation of in situ uranium mining was formalized with the issuance of a permit in January 1975 with the advent of ARCO's initial production scale (3 acre) effort in the Clay West area at the Moser mine site. Since 1975, the accelerating rate of mining and exploration activity is noticeable. There were 16 exploratory rigs operating early in 1977. This year, the rig count is averaging 46--a 287% increase. HISTORY OF LEGISLATION Paralleling this mining activity was state and federal legislation which subjected in situ mining to environmental regulation. The following is a brief chronology of the legislation that is directly or indirectly related to uranium mining. As most of you know, disposal wells are an integral part of most in situ uranium mines operating in Texas. They are used both during production and during aquifer restoration following production. The wells are regulated by the Texas Injection Well Act, enacted in 1961 by the Texas Legislature. In 1967, the Water Quality Act established the Texas Water Quality Board, and provided for the regulation of water quality by the so-called permit system. In 1969, the Solid Waste Act was enacted by the Texas Legislature. The legislation provides for control of wastes from manufacturing, mining, and agriculture. This Act regulated uranium surface mining activities until 1975 when the Texas Surface and Mining Reclamation Act placed responsibility with the Railroad Commission for uranium open-pit mining and surface mining of coal and lignite. In 1972, the Federal Water Pollution Control Act (Public Law 92-500) was passed. This legislation forms the legal base for the NPDES (National Pollutant Discharge Elimination System) and the subsequent point source effluent guidelines and standards. The November 6, 1975 issue of the Federal Register published interim final rules for Best Practical Treatment levels for effluent discharges from ore mining and dressing operations. Litigation was immediately initiated by eleven companies against these proposed rules, and they are currently being reconsidered for reissuance in 1979. In 1974, the Federal Safe Drinking Water Act (Public Law 93-523) was enacted. A part of this legislation is the Underground Injection Congrol Program. The regulations implementing this program have undergone various public hearings and it is expected that they will be published in the Federal Register before the end of 1978. In 1975, the Texas Surface Mining and Reclamation Act (Senate Bill 55), providing for the Railroad Commission's authority to require reclamation of surface mines, was passed. In 1977, an amendment to Senate Bill 55 was introduced that proposed to place regulation of in situ mining of coal, lignite, and

Jan 1, 1979

By G. K. Engelhart

EFFECTIVE use of rotary kiln waste gases to preheat dry pulverized materials has been demonstrated in full-scale operation at the Allentown Portland Cement Co. plant, Evansville, Pa. Pulverized raw materials are preheated in suspension in the gas stream in a multi-stage counterflow process which draws the gases through a series of cyclone collectors. Upon entering the first cyclone stage the material, continuously delivered and suspended in the gas stream, is successively collected and resuspended until it discharges through the kiln feed pipe. Gas and material contact time is thus prolonged, providing a high degree of heat recuperation with a very low temperature differential between gas and material at the final stage. The suspension preheater, developed by Klockner-Humboldt-Deutz AG of Cologne, Germany, was first installed at the Norddeutsche Huette plant, Oslebshausen, Germany. Similar preheaters are now in operation at three other German cement plants. The first American installation, at the Allentown Portland Cement Co. plant, was designed and manufactured by Fuller Co. of Catasauqua, Pa., Humboldt's licensee for the United States, Canada, and Mexico.

Jan 4, 1954

By Roger M. Nendick

The recovery of precious metals from heap leach solutions can be accomplished by two processes: 1. The Carbon Adsorption Process 2. The Merrill-Crowe Zinc Precipitation Process A brief review of the relative process economics is made. Each process presents certain design considerations that must be addressed during the evaluation and engineering design for the project. Discussion is presented on the design criteria for each process.

Jan 1, 1984

By Ove Rehnberg

Catalytic purifiers are widely used as exhaust treatment devices on diesel equipment in confined spaces. The paper summarizes some studies carried out at the University of Lulea on diesel exhaust purifiers. The main purpose has been to elucidate important chemical activities of catalysts useful for the improvement of their effect. The effects of platinum catalysts on exhaust constituents such as carbon monoxide, nitrogen oxides, unburned gaseous hydrocarbons, and polynuclear aromatic hydrocarbons are discussed. Also pointed out are the great differences in catalyst activity and advantages/disadvantages associated with the catalysts.

Jan 1, 1982

By AIME AIME

Further details of the 97th meeting of the Institute, at Spokane, have been sent to members in the Special Circular of May 8, 1909, and for convenience a summary of the additional information is given later in this announcement. In spite of the present small number who have joined the party, final arrangements have been made to complete the itinerary given in the circular. It is greatly to be desired, both in behalf of the Institute and in recognition of the special courtesies to be extended on the trip, that the party be made larger. Exceptional facilities to visit the many mines and smelters have been freely provided; and members are requested to make all reasonable effort to attend the meeting at Spokane and participate in the excursions. . For those who cannot take the entire trip, it may be possible to provide special Pullman accommodations after leaving the Yellowstone Park. In order to make the necessary arrangements, however, the names of members and guests contemplating this partial trip should be sent at once to Mr. Theodore Dwight, .39 West 39th St., New York, N. Y. A special train of Pullman cars will leave Chicago September 16. This train will be side-tracked at all places visited, and the sleepers will be available for lodging and the dining-car for meals (luring the entire trip, except while taking the tour through the Yellowstone Park. The general cost of the trip per member will be $300, which includes transportation, berth, and meals for the entire trip from Chicago back to Chicago, almost 6,000 miles, and the tour through Yellowstone Park, occupying in all about 30 days. Special accommodations on the train will be furnished at the following rates

Aug 1, 1909

By Albert C. Harding

FOR several years barite (BaSO4) production has topped such better known minerals as feldspar and fluorspar in annual tonnage and is now well established among our foremost nonmetallic industries. DESCRIPTION Of widespread occurrence in the United States, barite is relatively soft (hardness, 2.5 to 3.5), inert, heavy (specific gravity, 4.5), and is also called "barytes" (sometimes pronounced "bear-i-tease"), "heavy spar" and "tiff." It occurs with granular and earthy structure but usually has coarse, orthorhombic crystallization. It is commonly white, and although occurring in various shades of red, yellow, and gray, barite always gives a white streak and can be scratched by the ordinary prospecting pick. Its softness and weight are usually sufficient to establish field identification. Another aid is the "rotten egg" odor of H2S which sometimes emanates from freshly fractured surfaces. Barite can be readily distinguished from two other minerals which have somewhat similar occurrences and characteristics. The relatively rare celestite, strontium sulphate, has a specific gravity slightly less than 4.00 and gives a distinctively crimson color in a flame test. The very rare witherite, barium carbonate, has a specific gravity of 4.3 but readily effervesces with dilute hydrochloric acid. OCCURRENCE All known commercially important barite deposits in the United States occur as re placements or cavity fillings in schists, shales, limestones, dolomites, and quartzites, or as residual deposits from such formations. In Georgia, Tennessee, North Carolina, and Missouri, high-grade barite is recovered as fragments from residual clays covering quartzites and dolomites. In Arkansas, Nevada, and California, barite, usually of lower grade, is mined from replacement deposits. These seven states contributed the entire production reported by the U. S. Bureau of Mines for 1945 as given in Table I. [TABLE 1-Crude Barite Sold or Used by Producers in 1945 STATE SHORT TONS Arkansas260,660 Missouri225,467 Georgia110,393 Tennessee32,812 Nevada28,919 Other States37,811 Total 696,062] "Other States" included only California and North Carolina. Such a large part of this undistributed production came from California that that state probably outranked both Nevada and Tennessee. For the second consecutive year Arkansas was the leading producing state, particularly worthy of note because there was no commercial production of barite there prior to 1941 and because the entire production of Arkansas has come from one large deposit which is being operated by two companies. CONSUMPTION [The 1945 consumption as reported by the Bureau of Mines was: 482,442 tons as ground barite 139,288 tons in making lithopone 99,173 tons in producing barium -- chemicals Total 720,903 tons]

Jan 1, 1947

By J. T. Williams

The equilibria in the V-Zr alloy system were investigated by solidus temperature determinations, thermal analysis, dilatometry, electrical resistance measurements, microscopic examination, and X-ray diffraction analysis. There is a eutectic reaction at 1230°C between a compound, V2Zr, and a solid solution containing 10 pct V in ß zirconium. V2Zr decomposes at 1300°C into liquid and a solid solution containing about 10 pct Zr in vanadium. The eutectic composition is probably about 30 pct V. A eutectoid reaction between V2 Zr and a zirconium takes place at 777°C at a very high rate. The eutectoid composition is 5 wt pct V. The limit of solubility of zirconium in vanadium was estimated to be 5 pct at 600°C. No attempt was made to determine the liquidus for the system. THE recent availability of large quantities of high purity zirconium has stimulated the study of zirconium binary systems. The equilibrium diagram for the V-Zr system has received little attention, however. Wallbauml appears to have made the first report concerning the equilibria in these alloys. He reported the existence of a compound, V2Zr, having the MgZn2 ((214) type of structure with a, = 5.277 kX and c° = 8.647 kX. Anderson, Hayes, Roberson, and Kroll2 made a survey of some potentially useful zirconium binary alloys and found that zirconium probably dissolves a small amount of vanadium. They reported the probable existence of a compound between the two elements and suggested that the zirconium-rich solid solution undergoes a eutectic reaction with this compound. Pfeil," in a critical review of the existing information, estimated that the solubility of vanadium in zirconium is less than 4.7 pct and probably less than 1.8 pct. Rostoker and Yamamoto' proposed a partial diagram for the V-Zr system in a survey paper on vanadium binary alloys. Their diagram indicates the compound, V,Zr, a eutectic reaction at 1360°C, a peritectic reaction at 1740°C, and a limit of solubility of zirconium in vanadium of about 3 pct. They obtained no information on the equilibria in the zirconium-rich alloys. In view of the potential utility of the V-Zr alloys and the incomplete knowledge concerning the equilibria in the system, an attempt was made to establish the constitutional diagram. Preparation of the Alloys Raw Materials: The vanadium for making up these alloys came from the Electro Metallurgical Corp. Zirconium came from two sources. In the beginning of the investigation, sponge zirconium from the Bureau of Mines was used in making some of the alloys. Later, iodide metal made at the Westinghouse Atomic Power Development Laboratories became available. This material was used in the preparation of all the dilatometric and resistance specimens and about two-thirds of the solidus temperature specimens. A typical manufacturer's analysis of the vanadium is shown in Table I. No other analysis of the vanadium was made. The metal contained a dispersed second phase and did not have a sharp melting point. Typical results of spectrographic analysis of the Westinghouse zirconium are shown in Table 11. These data indicate a very high purity. The Bureau of Mines sponge metal was probably less pure but had good ductility. Melting: All of the alloys used in the investigation were made by melting pieces of vanadium and zirconium together in a dc electric arc furnace similar to those of Geach and Summers-Smith, craighead, Simmons, and Eastwood," and others. Melting was done in an atmosphere of helium scavenged of residual air by the preliminary melting of a separate charge of zirconium. Each ingot was turned over and melted at least three more times before removal from the furnace to aid in the attainment of homogeneity. Alloys prepared for use in the investigation are listed with the results of solidus determinations in Table III with the exception of the following compositions upon which no solidus determinations were made: 0.29, 0.54, 4.57, and 5.55 pct V. Analysis: The weight of each ingot made from iodide zirconium was within 0.1 g of the total weight of the initial charge, about 90 g. Since each component of each charge was weighed to the nearest 20 mg for amounts less than 10 g and to the nearest 0.1 g otherwise, the gross composition of an ingot could be calculated accurately. Chemical analysis for the vanadium content of several alloys agreed

Jan 1, 1956

By William C. Buell

As used in connection with open-hearth or other high-temperature operations, "insulation" refers to a multitude of substances, natural or manufactured, that have the one principal property of preventing the flow of heat by conduction to a greater degree than refractories can prevent it, the principal properties of the latter being resistance to temperature and/or chemical action. The term "control" as commonly applied to the mechanization of management functions is inappropriate without qualification, for without some degree of control of every operation we could produce no steel worthy of the name. Although grouped together in this paper, insulation and control in open-hearth furnaces have little, if any, interrelationship, therefore the paper is made up of two distinct parts. INSULATION OF OPEN-HEARTH FURNACES More than ten years ago the writer proposed the insulation of an acid open-hearth furnace system below the charging floor, and it was accomplished, with gratifying results. Possibly that was the first time the insulation of regenerators and slag pockets of any open-hearth furnace was undertaken, but shortly thereafter such insulation became general, and when the six groups of 15D-ton furnaces' were built in 1929-1930, they were completely insulated below the charging floor. While the practice was accepted at least five years ago, it was not well understood, however, as indicated by the following incident which occurred in connection with an installation made in 1929. After the

Jan 1, 1935

The Atlanta Mine is located in east central Nevada, in Lincoln County, 116 km (72 miles) south of Ely and 80 km (50 miles) northeast of the old mining town of Pioche. From this famous district, high-grade copper ore was mined and shipped to a smelter in Wales in the 1850s; an early day lead blast furnace was also in operation. The Standard Slag Company began operations in May 1975 on the well known Atlanta Mine, which was operated by Roy Hardy in the 1930s. The mill is currently processing 450 mtpd (500 stpd) of gold-silver bearing ore. Mining by open pit is in a brecciated zone occurring between limestone-dolomites on the foot wall and tertiary rhyolites on the hanging wall. The quartz breccia is considered among the most abrasive in the world - shovel teeth must be replaced every week. Stripping ratio is 3.9 to 1.0. Because of the hard abrasive ore, the crushing plant consists of four units: two jaw crushers in series, one Hydrocone, and one Gyradisc. Mine feed to the primary crusher is limited to 610 mm (24 in.) in size. The remaining crushers work in closed circuit with screens to produce a mill feed of 6 to 13 mm (0.25 and 0.50 in.). Hardness of the ore is demonstrated by the fact that the reversible liners of the primary jaw crusher had to be replaced in early 1978 after handling only 39,000 mt (44,000 st) at a cost of $0.095 per mt ($0.086 per st). Another example of the extreme abrasiveness of the breccia ore was the total cost per ton in 1977 for all wear parts in the comminution circuit, including screens and grinding media. This amounted to $2.84 per mt ($2.58 per st). The Atlanta grinding plant consists of three ball mills to grind the 7 mm (1 /4 in.) crushing plant product to 85 to 90% minus 150 microns (100 mesh). Feed rate to the primary Tricone mill is determined by maintaining a cyclone overflow at 28 to 38% solids, which controls the grind mentioned above. A mixture of 90 and 65 mm (3.5 and 2.5 in. ) balls are charged to this primary mill. Both the secondary mills are charged with 50 mm (2 in ) balls. Total ball consumption is 2 kg per mt (4 lb per st). All three ball mills use rubber liners. Primary mill cyclone underflows are fed to the secondary mills close circuited with the same cyclones.

Jan 1, 1981

The Pinson Mining Co., which will start production in very early 1981, is the fourth Carbon-In-Pulp plant to be put into operation in the United States. The property is located in Humbolt County, Nevada, 38 km (24 miles) northeast of the town of Golconda. The famous Getchell Mine was also near Golconda and was the site of one of the early Carbon-In-Pulp plants in the 1940s. The deposit was discovered in 1971 by Reno based Cordilleran Explorations, which is founded by a consortium of Canadian mining companies. Cordilleran is a partnership consisting of John Livermore and Peter Galli. In 1972 a second but smaller deposit, called "Preble", was discovered at a location 15 miles south of Pinson. During 1980, a decision was made to place the Pinson deposit into production and Pinson Mining Company was formed. Ownership of Pinson is vested in Lacana Mining Inc. , Rayrock Mines, Inc. , Siscoe Metals, Inc., John S. Livermore, Peter E. Galli and Donald M. Duncan. Three distinct but connected ore zones occur at Pinson. Combined reserves of milling ore total 3, 200, 000 tons at an average (undiluted) grade of 4. 12 g per mt (0. 12 oz per st) Au. Initial mining will be from "A" zone which contains 1, 500, 000 tons with an average (undiluted) grade of 5. 8 g per mt (0. 17 oz per st) Au. An additional 5, 500, 000 tons of low grade ore will be mined from the Pinson deposit and processed by heap leaching. Mining reserves at Preble total at least 1, 500, 000 tons grading 2. 7 g per mt (0. 08 oz per st) Au. Production plans for the Preble deposit have not been formulated at the date of writing. Gold mineralization at both deposits is finely disseminated as sub micron sized particles. The ore at Pinson is structurally controlled and occurs in an Ordovician limestone-siltstone unit. Much of the ore has been silicified to a jasperoid. The ore zones have been entirely oxidized. Preble ore occurs in the Cambrian formation in a carbonaceous, limey shale. Only the upper part of the Preble is oxidized and amenable to conventional cyanide leaching. The Pinson ore body is adjacent to the mouth of Granite Creek in the Osgood Mountains at an elevation of 1, 615 m (5, 300 ft) with the mill being 1. 2 km (3/4 mile) from the mine at an elevation of 1, 495 m (4, 900 ft). Mine development work began in May of 1980 with ore being stockpiled for later processing. Pertinent factors affecting

Jan 1, 1981

With the signing of the armistice on Nov. 11, the direction of the main concentration of effort of the United States was changed. In order to win the war, all industrial efforts had to be organized and centralized. With the war won and peace in sight, this centralization of effort stopped and the full play of individual initiative was allowed to resume its sway in the community. During this period of reversal of direction of effort, there was a natural loss of momentum and the United States, as well as the rest of the world, is in for a period of readjustment. The immense progress that was made in one direction under the stress of the necessities of war, which focused the energies of a nation in one direction, is an outstanding example of what can be accomplished if a community with many varying interests can be united on one objective which it desires to attain. The realization that the fusing of many interests into one stream of effort is difficult should not prevent us from taking the long view ahead that is necessary in order to be able to measure the progress made. If we don't have a mountain peak to guide us, we are very likely to run in circles in the plain without reaching the goal to which we strive. The most efficient development of natural resources is an ideal that, from a material point of view, appeals to the engineer. This ideal includes giving of opportunities to everyone to take a share in the development of these resources.. It also contemplates rewarding foresight

Jan 4, 1919

By George Otis Smith

The Secretary of the Interior in his recent report to the President has defined the new public-land policy, which is in fact "but a new application of an old policy." His words may be more acceptable on this subject of land classification than the repetition of phrases which have served some of us for several years. Secretary Lane says of the past: 1'Congress has always been most generous as to the disposition of the national lands.... There was land for all, and it was the government's glad function to distribute it and let those profit who could.... And this generous donor was not so petty as to discriminate between kinds of lands, the uses to which they could be put, or the purposes which those might have who got them. Land is land, save when it contains minerals; this was roughly the broad principle adopted. To classify was a task too difficult or not worth while. The lands would classify themselves when they arrived in individual ownership. And so the door was opened for monopoly and for fraud." Of the reaction and the evolution of a new policy, the Secretary con. tinues: • ' " A reaction was inevitable. If lands were to be withdrawn from public service, why might not the government do the withdrawing itself? The old philosophy that land is land' was evidently unfitted to a country where land is sometimes timber and sometimes coal; indeed, where land may mean water—water for tens of thousands of needy neighboring acres. For the lands of the West differ as men do, in character and condition and degree of usefulness. We had not recognized this fact when we said 'land is land.' Lands fitted for dry farming and lands that must forever lie unused without irrigation; lands that are worthless save for their timber; lands that are rich in grasses and lands that are poor in grasses; lands underlain with the non-precious minerals essential to industry or agriculture; lands that are invaluable for reservoir or dam sites— these varieties may be multiplied, and each new variety emphasizes the fact that each kind of land has its own future and affords its own opportunity for contributing to the nation's wealth.

Jan 1, 1915

By Carl Samans

THE attention of physicists and metallurgists has been directed toward the study and explanation of the deformation textures in metals for the past 15 years. In 1920 N. Uspenski and S. Konobejewski1 were first able to show that the symmetrical X-ray diffraction effects that had been previously reported by E. Hupka2 and others in metal foils were caused by a directed arrangement of the crystallites. Since then, the systematic study of textures resulting from the application of the pure forces of tension or compression to polycrystalline materials hag been supple-mented by many investigations on deformed single crystals, which have greatly added to our knowledge of deformation. However, despite the valuable information secured from these comparative studies only four investigations upon cold-rolled single crystals of any of the face-centered cubic metals have been reported in the literature. This lack of quantita-tive data is especially unfortunate because of the much greater practical significance of rolling textures and their effects in both cold-rolled and annealed materials. This investigation was undertaken for the purpose of specifying the deformation of rolled single crystals in the hope that such information might later facilitate the explanation of polycrystal-line textures.

Jan 1, 1934

By Joseph W. Siefke

Jan 1, 1985

By Robin O. Williams

Robin 0. Williams (Oak Ridge National Laboratory)— The authors have questioned the degree to which the coherency strains between the iron-rich and chromium-rich phases are isotropic as proposed in Ref. 5 on the basis of the difference between the elastic properties of the two phases. The relative magnitude of the stresses is determined by the moduli as shown by Eqs. [2], [3], and [4] of Ref. 34. However, the moduli of the two phases have no direct bearing on the uniformity of either the stress or strain within either phase. The idea that the strains are isotropic within each phase (but normally of different magnitude and always of different sign) is based entirely upon the experimental observation that X-ray line broadening has not been detected even when the particles become rather large. It has not proven possible to grow the particles sufficiently large that they lose coherency. Based upon this lack of line broadening one can estimate an upper limit for the nonuniformity of the strains within each phase as follows. It is considered possible to detect line broadening if it is as great as 10 pct of the separation of the K, doublet for the (211) line using chromium radiation. The doublet separation would correspond to a total strain of 0.0017 such that the total variation of lattice parameter relative to the average lattice is now k0.05x0.0017 or something less than ± * For the present case the strain in each phase is roughly 0.002 such that the variation of strain within a phase will not exceed 5 pct. It is stated that the expression derived for strengthening for the hydrostatic straining as observed in this system would substantially overestimate the magnitude due to dislocation flexure. This is contrary to the conclusion reached in the original paper34 for the present range of particle sizes. What is the lowest temperature at which a has been observed to form in this alloy? M. J. Marcinkowski, R. M. Fisher, and A. Szirmae (nutlzors' reply)— -Williams' arguments based on X-ray findings for a chromium-rich precipitate and an iron-rich matrix strained to a common lattice parameter are certainly convincing. This being the case, there are no shear components of strain associated with the precipitate-matrix aggregate to interact with the shear components of the dislocation stress fields, contrary to the opinion expressed by the present authors. On the other hand, the present authors, in spite of this error, did not expect the shear interactions to be significant. The chief objection to Williams' model in the present case is that the various segments of the dislocation line are assumed to pass from one potential valley to the next independently of neighboring segments. This is only true for a highly flexible dislocation line, i.e., one whose radius of curvature is something less than the center to center distance between precipitate particles which amounts to about 90A in the present alloy. In order to maintain this curvature, an externally applied shear stress of at least 230,000 lb per sq in. would be required or about four times the observed stress. It is therefore concluded that the dislocation lines move rather rigidly through the lattice. This being the case, the forces on the dislocation resulting from the hydrostatic interaction between the stress fields of the edge-dislocation components and the precipitate particles should average out to zero; that is particles above the below the slip plane produce forces on the dislocation of opposite sign and therefore will cancel when averaged over the entire length of the dislocation. On the other hand, since the dislocation is not perfectly rigid, Williams' model may lead to some strengthening, but far less than that predicted. A second and equally serious objective to using Williams' strengthening model for the present alloys is that profuse wavy slip due to the motion of screw dislocations played a predominant role not only in the unaged alloys but in the fully aged ones as well. Since the screw dislocation has associated with it only shear components of stress the hydrostatic strengthening model no longer applies. In view of these arguments the present authors must reject Williams' model of strengthening as being pertinent to the present alloy system. The present authors have made no detailed study of the lowest temperature at which a forms in the quenched ferritic alloys. None was ever observed n the alloys aged at 500°C so that forma-tion must occur at temperatures higher than this and was therefore not a factor in the present study.

Jan 1, 1965

By Arthur Notman

DURING the past fifteen years there has been a great change in the methods of treating employ-ment and discharge throughout industry. Perhaps nowhere has this change come more abruptly than in the metal mining districts of the West. In 1909, when I went to work for the Phelps Dodge Corporation in Bisbee, their operations were roughly arranged accord-ing to shafts in seven divisions, each employing from 100 to 250 men underground, and the mechanical department employing some 250 men, mostly on the surface. The underground divisions were each in charge of a foreman who had under him a night foreman and from two to four shift bosses on' each of two shifts. These foremen reported to the underground superinten-dent and he in turn to the superintendent of the mine department. The mechanical department was in charge of the master mechanic who reported to the superintendent of the mine department. RUSTLING A JOB IN THE OLD DAYS It was customary for men seeking employment to "rustle" the division foreman at the shaft during the lunch hour or at the close of the day shift and the master mechanic at the shops. There was no real attempt at interviewing the applicants for underground work. They simply filed in and out of the foremen's office-50 to 150 strong-in ten or fifteen minutes. If the foreman needed men, and he generally did; to replace those that he and the shift bosses had removed during the morning, he picked out those he knew or strangers who took his' fancy. The former in many cases were chosen for negative reasons rather than positive. In selecting the latter, the foreman felt that if they failed to show ability promptly, he could replace them the next day, and often did so. Even if these foremen had been skilful and well trained in the art of selecting men, it would have been impossible under the pressure of other duties to exercise that skill and experience in so doing. The conditions in the mechani-cal department were little better. About all that can be said in favor of such a method was that with a sur-plus of labor it "got by." The labor shortage brought about by the war disclosed its fundamental weakness.

Jan 6, 1923

By Ernest F. Burchard

PAGE. I. Introduction,........... 75 II. Outline of the Geology......... 76 1. Stratigraphy............ 76 A. Clinton Formation........ 77 2. Structure...........82 3. The Ore..........85 A. Character............ 85 B. Geographic Distribution....88 III. Local Descriptions........... 88 1. Birmingham District.......... 88 A. Topography and Its Relation to Industrial Development... 88 H. Distribution and Structure of Formations.... 89 C. Divisions of the Birmingham District. 95 Division A (Description of the Ore-Beds), . 95 Division B.........105 Division C.......... 106 Division D,..107 Division E,...........108 Division F........ 111 Division C.......... 112 D. Mining .Development.... 113 2. Northeast Alabama........114 IV. Possible Origin oF the Ore......... 119 V. Relation of Origin to Quality and Extent of Ore... 122 VI. Estimates of Ore-Reserves,......... 125 1. Method of Making Estimates......... 125 2. Data and Results....126 VII. Production and Consumption oF IRon-ORe,.... 132 I. Introduction. Brief and interrupted studies of the Alabama Clinton iron-ores have been made within the last four years by members of the IT. S. Geological Survey. Reports on the progress of this

Jan 1, 1910