Search Documents

By E. C. Goodhue, R. D. Coleman, I. E. Puddington, A. F. Sirianni

Iron ore samples containing apatite are fractionated to acceptable products by spherical agglomeration methods. The phosphorus is upgraded by a factor of 10 at an elevated pH. High-grade iron products are obtained in good yields from the tailings in a second step of the operation. The grade of the phosphorus separated appears to reach a maximum at about pH = 10; recovery of iron decreases below about pH = 4. Both the recovery and grade of iron are found to be reduced sharply above about pH = 8.

Jan 1, 1968

By Barry Hope, Javier Rico

"Goldcorp’s Hoyle Pond mine has recently completed several projects which have impacted the overall ventilation system. The project includes extending the Fresh Air Raise (FAR) to depth, development of a new Return Air Raise (RAR), and the installation of new sensors and ventilation controls throughout the mine. Two years after the completion of #2 Winze, the mine is ramping up its ore production to 1,300 tpd (up from 1,100). To ensure safe and profitable production, a reliance upon technology has been needed to provide the required ventilation to the work areas according to the mine plan. To systematically assess the mine’s ventilation in real-time, a significant increase in remote monitoring was required. This included installing additional flow, pressure, temperature and gas sensors. The first step in upgrading the existing monitoring was to purchase airflow and differential pressure monitors and install them in key areas of the mine. This paper presents the process of expanding the monitoring capability at Hoyle Pond mine, the selected equipment and the results of the implementation. The intended goal was to improve safety while minimizing capital and operation costs. The monitors were installed in strategic locations to provide immediate feedback on the impact of changes to the primary ventilation airflows. Comparing the available sensor technologies, installing them and systematically monitoring the ventilation served as a first step towards developing a mine wide Ventilation Control System. In addition, the initial state of the monitoring and control system, with final results and the chosen solution for the mine site, are presented. INTRODUCTION The Hoyle Pond mine is located in the City of Timmins, within the Porcupine mining district, Ontario, which has produced more than 70 million ounces of gold since 1910. Currently, approximately 60% of Porcupine Gold Mines gold production comes from the Hoyle Pond underground mine. Mechanized cut and fill and long-hole mining methods are used to extract the ore. The remainder of the ore comes from the Hollinger Open Pit mine. The Dome Underground mine ceased operations in 2017. Hoyle Pond is currently mining at 1820 meters below the surface and plans to go deeper. The average dry-bulb as wet-bulb temperature underground varies according to the depth and surface conditions which has extremes of –40°C in winter to +30°C in summer. The total airflow volume pushed down from surface is 240 m3/s to accommodate the diesel-powered equipment needed for normal operations. In order to improve the quality of air underground a program has been implemented to use diesel particulate filters, starting with the truck fleet and 6-yard scoops, followed by the intention to implement the rest of the functional diesel-powered equipment and eventually move to electric equipment."

Jan 1, 2019

By A. Haldar

This study focuses on the flow characteristics of hypereutectic Al-Si alloys in thin sections. The pattern assembly consisted of spiral horizontal patterns, 6.25 mm (0.25 inch) and 12.50 mm (0.50 inch) in thickness with a common sprue. Al-Si alloys with silicon levels of 14%, 18% and 22% were poured with superheats of 60°C, 115°C and 170°C. It was observed that metal fluidity (in terms of flow length and metal velocity) increased with increase in silicon levels and superheat for both section thicknesses. It was also observed that, for a section thickness of 6.25 mm (0.25 inch), silicon level had more pronounced effect on the metal fluidity. For 12.50 mm (0.50 inch) thickness, both silicon level and superheat affected the metal fluidity. The surface hardness of the castings increased with an increase in silicon level of the alloys at the gate and the flow tip. Detailed study of the flow tip was also carried out with a view to understanding the effect of silicon level and superheat on undulated flow length, surface hardness and microstructure.

Jan 1, 2007

By C. Allen, M. Gangal, J. Stachulak

"Most underground diesel equipment is equipped with diesel oxidization catalysts (DOCs) to reduce carbon monoxide and hydrocarbon emissions. DOCs do not alter nitrogen oxides concentrations but can promote the oxidization of nitric oxide (NO) to the more toxic nitrogen dioxide (NO2). Vale and CanmetMINING have been researching how to reduce worker exposure to diesel emissions by testing mining equipment DOCs. Results indicate a > 77% decrease in carbon monoxide concentration but a 46–315% increase in NO2 concentration for 8-mode test cycles. It is recommended that DOCs that increase NO2 emissions be evaluated regarding their continued use in underground operations.RÉSUMÉ La plupart des équipements miniers souterrains sont équipés de catalyseurs d’oxydation diesel (DOC) afin de réduire les émissions de monoxyde de carbone et d’hydrocarbures. Les DOC ne modifient pas les concentrations des oxydes d’azote mais ils peuvent faciliter l’oxydation du monoxide d’azote (NO) en dioxyde d’azote (NO2), plus toxique. Vale et CanmetMINING effectuent des recherches pour réduire l’exposition des travailleurs aux émissions de diesel en analysant les DOC des équipements miniers. Selon les résultats, une diminution > 77 % dans la concentration de monoxyde de carbone est atteinte mais elle est accompagnée d’une augmentation de 46 à 315 % de la concentration en NO2 pour des cycles d’essais à 8 modes. Il est recommandé d’évaluer les DOC qui augmentent les émissions de NO2 pour décider de la poursuite de leur utilisation dans les opérations souterraines."

Jan 1, 2016

By C. R. Edwards

"Since the first commercial extraction of uranium in the early 1940s, the range of feasible process alternatives has greatly increased. This paper reviews process options to reduce extraction costs, improve efficiencies, effect safer operations, and lessen environmental impacts. Equipment and processes used in the past, in use now, and that could be considered for future use are described.BackgroundTwo billion years ago life on earth consisted solely of single celled creatures of the simplest design (Gould 1989). Incredible as it may seem, uranium fission reactors were operating then also. In what is now western Africa, a series of natural reactors were fueled by rich uranium deposits in contact with underground rivers. Water from the rivers provided the moderator necessary to sustain the nuclear fission chain reaction. These primordial reactors ran down after about 600 000 years (Ontario Hydro 1989).Because it is ubiquitous in the earth's crust, humans have always been in contact with uranium. Mining of uranium, albeit not intentional, is ancient ; uranium minerals were embedded in ore veins mined for metals such as silver and copper.Uranium was discovered in 1789 in Berlin by an apothecary, Martin Heinrich Klaproth, who named the element after the recently discovered planet Uranus. The metallic element uranium, as opposed to its compounds, was extracted in 1841 by the French chemist Eugene-Melchior Peligot. The atomic mass of uranium was calculated to be 120, but the Russian genius Dmitri Ivanovich Mendeleev (famous and welcome everywhere except in Russia, where his liberal politics were detested by the Tsar), found this did not fit into his periodic table, and submitted a value of 240. Mendeleev was close; the exact atomic mass is 238.029.Henri Becquerel's detection of the radioactivity of uranium in 1896excited scientific study of the metal, but virtually no practical use was found for uranium outside of a minimal consumption as a colouring agent for glass and ceramics. Scientific interest intensified in the 19305. In 1933 Leo Szilard patented the concept of the nuclear chain reaction. While walking to work on a fine fall London morning and mulling over the problem of how to release atomic energy, he was stopped by a red light. He stood in thought and conceived the notion of the neutron-activated chain reaction before the light turned green. The patent was filed in 1934, and Szilard assigned it to the British Admiralty in order to keep it secret, in an honourable but ultimately futile effort to prevent the misuse of science (Bronowski 1973)."

Jan 1, 1992

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By K Byrne, W. Hawker

The average grade of copper concentrate is steadily declining, forcing the industry to turn to lower grade and metallurgically challenging orebodies. When faced with a low grade, challenging ore, mining companies are often forced to choose between high recovery at low grade or low recovery at high grade. Hydrometallurgical processing of copper concentrates using metathesis reactions, which replace iron with copper in copper-iron sulphide minerals and increase the copper to sulphur ratio in copper sulphide minerals, provide an opportunity to upgrade copper concentrates and potentially allow high copper recovery for a high grade concentrate. Factors such as concentrate mineralogy, reaction time and temperature, and the concentrations of copper, chloride and acid in solution are reported to affect the reaction extent and mineral phases formed by metathesis. In this paper, a copper concentrate has been studied over a wide range of conditions to investigate the influence of these key parameters on the extent of copper metathesis reactions and product phases formed. Solution and solid phases are assayed with the main mineral phases identified by Quantitative X-Ray Diffraction. INTRODUCTION The minerals present in copper deposits determine the prospective processing options either: pyrometallurgical or hydrometallurgical. For copper oxide ores, copper is typically present as oxides, carbonate, chlorides, silicates and sulphates. These minerals are readily solubilised in acid and are usually treated through hydrometallurgical processes. The typical process route for copper oxides is to leach copper into aqueous solution, purify and upgrade the solution phase through solvent extraction and then recover copper as metal by electrowinning (Davenport, King, Schlesinger, & Biswas, 2002). Copper sulphide deposits may contain a multitude of copper bearing minerals, including chalcopyrite, bornite, enargite, covellite, digenite and chalcocite. The copper ore grade and treatment options are affected by the mineral type and distribution. Sulphide ores are typically treated through comminution and mineral flotation to form concentrates, followed by pyrometallurgical smelting. Hydrometallurgy can also be used to process sulphides depending on the mineralogy and impurity levels (Davenport et al., 2002). The trend of decreasing copper grade with increasing impurity levels are common across the mining industry and pose future challenges to copper processing. This trend has prompted research into hydrometallurgical options for upgrading copper concentrates. One promising hydrometallurgical option is using metathesis reactions. Metathesis reactions, sometimes also called double replacement or displacement reactions, are chemical processes involving the exchange of bonds between two chemical compounds or species. In this case, the metathesis reactions involve copper in solution exchanging with cations in the solid sulphide concentrate. The driving force for copper sulphide metathesis is the relative affinity of the exchanging cation elements for sulphide. Based on sulphide precipitation diagrams, the expected order of affinity for sulphide should be Hg2+ > Ag+ > Cu+ > Cu2+ > Bi3+ > Cd2+ > Pb2+ > Sn2+ > Zn2+ > Co2+ > Ni2+ > Fe2+ > Mn2+ (Monhemius, 1977). Hence, copper metathesis reactions are capable of increasing copper content and removing impurities such as iron, nickel, zinc and lead from copper concentrates.

Jan 1, 2019

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

By E. Rosseland

Glencore Nikkelverk is operating its Chlorine Leach Process in Kristiansand, Norway, producing nickel, copper and cobalt metals by electrowinning. The copper tankhouse, with an annual capacity of 40 000 tons, is based on traditional technology with copper starting sheets and cast lead anodes. Due to the integration of this copper sulphate process in a nickel chloride refinery, operating conditions are unique. In recent years, operating costs have escalated, and health, safety and environment are top priorities. Test work on a new copper process involving permanent cathodes was therefore initiated in 2007, and a pilot plant was started up in 2012. The objective was to introduce innovative technologies and tailor these to be robust in the Nikkelverk process, to form a basis for a new sustainable copper tankhouse with a high degree of automation. Key learnings from more than 10 years of R&D work is presented, focusing on cathode materials and copper metal deposition including product quality, robotic stripping, coated titanium anodes, electrode contacts and alignment, electrode current monitoring with Hatch HELM tracker technology and acid mist capture using cell hoods with off-gas scrubbing. The new copper tankhouse project was approved in December 2018, and commissioning is planned in 2022. INTRODUCTION The Kristiansand nickel refinery was started up in 1910, processing nickel-copper matte originating from Norwegian mines. It was the first industrial plant in the world to produce nickel by electrolysis using the Hybinette electrorefining process. After roasting to burn off sulphur in the matte, copper was leached and recovered as cathodes by electrowinning with lead anodes. In the first years, the copper cathodes were fire- refined and cast into ingots for sale (Thonstad Sandvik, 2004). The Nikkelverk refinery was acquired by Falconbridge Ltd. in 1929, and since then matte from Sudbury, Canada has been the main feed source. The Hybinette process was in operation until 1975 when conversion to the newly developed Chlorine Leach Process was started (Stensholt, Zachariasen, & Lund, 1986). In this process still used today, nickel and part of the copper in the matte is leached using chlorine gas generated on dimensionally stable anodes in the nickel and cobalt electrowinning tankhouses, as illustrated in Figure 1. The presence of dissolved copper ions in the strong chloride leach solution is essential for effective chlorine absorption and nickel dissolution. To improve copper-nickel separation, slurry from the atmospheric leach is pumped to autoclaves and then to cementation tanks for precipitation of copper as copper sulphide, which is collected in filter presses. The leach residue, also containing the precious metals, goes through a 3-stage wash to remove chlorides before being introduced as a slurry to fluid-bed roasters for sulphur removal. The resulting calcine is then leached in spent electrolyte from the copper electrowinning tankhouse, to dissolve most of the copper and also some nickel, cobalt and other elements. After separation of the leach residue, elements like Bi, Te, As and Ag are removed from the strong copper sulphate solution by reaction with metallic copper in three columns in series filled with cut copper cathodes. The purified solution then passes polishing filters before being mixed with spent electrolyte and returned to the electrowinning cells.

Jan 1, 2019

By D. S. Flett, A. V. Tolstov, M. A. Mulagaleeva, N. V. Gudkova, A. M. Zhizhaev, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina

The complex niobium-rare earth pyrochlore-monazite-crandallite ores of the Tomtor deposit, located in the Siberian Arctic, should be considered as a new type of rare metal materials. The major valuable components of the ore are niobium, rare earth elements, yttrium, and scandium; associated components are titanium, vanadium, aluminum, and phosphorus. Because of the irregular distribution of the rare earth metals and niobium according to grain-size, the extremely finely dispersed nature of the minerals and their close interpenetration to each other, ore processing by gravitation and flotation is not successful. The processes studied for the treatment of the Tomtor ores use direct alkaline-acid leaching to open the ore. A problem in the first stage of alkaline leaching is the high aluminum content, which decreases the activity of sodium hydroxide and alkaline-earth metals, which are bound to phosphorus. Ore processing using alkaline-nitrate and alkaline-chloride leaching was proposed and investigated. The first variant was used to obtain rare earth and scandium materials and a niobium-titanium concentrate, which can be a stock material for processors who use chlorination for the processing of ores and concentrates. The second variant is a complex advanced ore processing scheme with electrochemical regeneration of the waste chloride solutions obtaining sodium hydroxide, hydrochloric acid, and chloridizing agents. Moreover trisodium phosphate is used for purification of the waste mother liquors from metal cations. The complex salt, NaAlCl4, is proposed as the chloridizing agent for the decomposition of the niobium-titanium concentrate.

Jan 1, 2016

By A. L. Valdivieso

"The correlation obtained by plotting pH of maximum adsorption of dextrin versus the isoelectric point of involved metal hydroxides can be used to predict the depressing effect of dextrin on flotation in ""pure"" sulfide mineral systems. Sulfides are strongly depressed by dextrin whenever their surfaces are coated by the corresponding metal hydroxide. The efficiency of dextrin as a depressant is affected by the adsorption of the sulfhydryl collector. Hydrolyzable cations modify this relationship in flotation of sulfide ores. This type of deviation of the real-life systems from the predictions based on the behavior of the pure systems shows the possible ways that could be followed to further improve the obtained correlations. Advances in Mineral Processing Science and Technology Proceedings of the 48th Annual Conference of Metallurgists ofCIM Sudbury, Ontario, Canada Edited by"

Jan 1, 2009

By H. Son

The three-dimensional (3D) reconstruction of as-built industrial plant models plays an important role in revamping planning, maintenance planning, and preparation for dismantling during the lifecycle of industrial plants. Recently, the 3D reconstruction of existing industrial plants was conducted using laserscan data to make surveying processes more efficient. However, the current 3D reconstruction process from laser-scan data is still limited due to the need for significant human assistance. Although a great deal of effort has been made to efficiently reconstruct 3D as-built industrial plant models, the presence of objects?such as equipment, pipelines, and valves of different sizes and shapes?in existing industrial plants significantly increases the complexity of laser-scan data and makes automating the reconstruction process more challenging in practice. The purpose of this study is to propose a knowledge-based approach for the 3D reconstruction of as-built industrial plant models from unstructured laser-scan data. First, pipelines were extracted from laser-scan data based on surface curvature information and knowledge about pipelines' sizes from existing piping and instrumentation diagrams (P&ID). Once entire pipelines were extracted, they were modeled based on skeleton features. Then, the remaining objects were clustered and grouped separately via the region grouping process. Afterward, clustered objects were retrieved and modeled based on global feature-based matching from the 3D database. Finally, the resulting model was checked to ensure that it was well-reconstructed according to the information regarding the relationships among objects abstracted from the existing P&ID. The preliminary results on actual industrial plants show that integrating knowledge into the reconstruction steps played an important role in the proposed approach and that this approach obtained accurate as-built industrial plant models from unstructured laser-scan data. The proposed approach could be successfully utilized to assist in many applications during the lifecycle of industrial plants.

Aug 1, 2013

By V. G. Papangelakis, I. Guzman, S. J. Thorpe

Pressure oxidation (POX) leaching has been commercially applied to refractory gold ores since the 1980s. In the process, sulphide material is oxidized and dissolved in order to release the gold encapsulated in the sulphide matrix, making the gold available for further recovery. Redox potential is a significant parameter during POX, however it is only measured ex-situ at atmospheric conditions. In-situ redox potential measurement would provide instant information that allowing adjusting the process parameters accordingly. In the present study, redox potential measurements were performed during POX of sulphide material at high temperatures and high pressures. The working electrode was an Ir electrode combined with a flow-through reference electrode in a novel and robust configuration. Experiments were performed in a 2 L titanium autoclave, at 200–220°C, 50–110 psi oxygen overpressure, and 10–30% solids mass fraction. Temperature and oxygen pressure conditions were selected in order to reflect POX of refractory gold ores. Results show that the Ir electrode is consistent with theory and is able to perform well under these conditions, showing promise as a new in-situ sensor.

Jan 1, 2017

By C. Caballero, K. Itagaki, P. Morales, A. Moyano, J. Font

Codelco-Chile is considering different processing options for the new projected concentrate from the Alejandro Hales mine. This concentrate is featured by its high arsenic content of up to 6%. Thus, it is important for Codelco Norte Smelter to define the technical feasibility for processing this high-arsenic bearing concentrate in its main smelting unit as it is the Teniente Converter, which beside of its dual feeding system can enhance the arsenic removal by volatilization. The present paper which is a part of an extensive research work will focus in the performed industrial scale test for processing about 7,000 tonnes of a high-arsenic bearing concentrates in the Teniente Converter at the processing rate of about 2,300 tpd. The impact on the chemical quality of the produced high grade matte will be discussed, and the effect of the As removal by increasing the Teniente Converter processing rate of concentrates up to 3,000 tpd when producing 70% Cu in the white metal will also be addressed.

Jan 1, 2007

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By D. Satish Kumar, D. Mazumdar

"95% bulk mixing times in three different size water model ladles of a 140 T cylindrical shaped , dual plug ( located diametrically opposite at mid bath radius position) stirred, industrial ladle were determined experimentally with and without an upper buoyant phase. Based on dimensional analysis and a regression of the experimental data and, it was shown that in the inertial and gravitational force dominated flow regimes, 95% bulk mixing times for a slag-less situation can be described via:[equation]Parallel to this, a large number of experiments were also carried out in one of the water models (D=0.30m) to quantify the influence of an upper buoyant phase on mixing. These indicated that mixing time, operating variables and thermo-physical properties of the upper phase liquid can be correlated via a dimensionless relationship of the type:[equation]in which, Q is the ambient gas flow rate, L is the depth of liquid , (AL) is the slag layer thickness and 6 and t are respectively the surface tension and viscosity of the upper phase fluid The dimensional analysis, regression of experimental data as well as the adequacy of the proposed correlations are discussed in the text."

Jan 1, 2004

By F. Chevarin

The reaction of O2 with the carbon anode is considered as the main parasitic chemical reaction affecting Hall-Heroult process anodes. The current study aims at investigating the influence of the microstructure of baked anode on its overconsumption. Samples were removed from different positions of an industrial anode. Density, porosity, Lc and BET specific surface area were measured. The anode reactivity was evaluated based on the weight losses for the samples resulting from the reaction of anode with air at 550°C after 7h. The essential parameters determined to control the air reactivity are closed porosity, Lc and pores with a pore entrance radius of 1.5, 8.5 and 12 p.m. The knowledge of effects of these parameters allows better understanding of the reactivity of anodes and consequently reduction of their overconsumption in electrolysis bath.

Jan 1, 2011

By M. E. Holter

"Limestone-bearing strata are exposed in seven areas of Alberta, each situated adjacent to rail and road facilities. Six of these centers are located along the eastern edge of the Foothills and Front Ranges of the Rocky Mountains in western Alberta. The other is in northeastern Alberta, along the eastern margin of the Alberta Basin. High-grade limestones are present in Middle Cambrian, Upper Devonian and Mississippian strata. Middle Cambrian (Eldon Formation) limestones have been exploited only in the Exshaw area west of Calgary, where they formerly were used for lime production. Limestone beds of the Upper Devonian Palliser Formation are exploited at Exshaw and at Cadomin in west-central Alberta for the manufacture of cement. Reserves of high-grade limestone also are available in the Palliser Formation near Crowsnest Lake in southwestern Alberta and near BrUle, west of Edmonton. Upper Devonian limestones of the Waterways Formation are widespread in the Fort McMurray area of northeastern Alberta, but available data indicate they are of inferior quality to the limestone deposits of the Rocky Mountains regions. The Mississippian Livingstone Formation contains large reserves of high-grade limestone at several localities in the Rocky Mountains and Foothills. Commercial development of the unit is now underway at Crowsnest Lake and at Exshaw for lime production, and future exploitation of these beds is feasible at Blairmore and Nordegg."

Jan 1, 1973

By A. Ghirian

Once cemented paste backfill (CPB) is transferred and placed into a mine stope, various coupled mechanisms will take place in the CPB material or structure. It will be subjected to strong coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes. Field studies have shown that the in-situ properties and performance of CPB differ from those obtained in the laboratory. This is mainly due to effects of the aforementioned coupled THMC mechanisms or processes. For a reliable and cost-effective design of a CPB structure and barricade, it is crucial to have a proper understanding of the THMC behaviour and evolution of CPB. Also, it is important to consider the effect of coupled THMC factors (e.g., self-weight pressure, drained/undrained and thermal conditions, pore pressure) while curing the CPB specimens. For this purpose, a laboratory setup is developed to investigate the properties of CPB materials. The setup is capable of curing CPB specimens (10 cm in diameter and 20 cm in height) under controlled vertical pressure (curing under stress) and various coupled THMC conditions, while continuously monitoring the evolution of total stress, pore pressure, suction, temperature, water drainage, chemical composition of the pore water and vertical deformation. Once the required curing time is achieved, the specimen can be extracted and then subjected to experimental tests of interest, such as those that determine the Unconfined Compressive Strength (UCS), shear strength parameters, saturated hydraulic conductivity and thermal properties. In this paper, we describe the developed experimental setup and present some results of the THMC behaviour of CPB under various curing stresses and rates of backfilling. The obtained results show that the THMC properties of CPB are strongly coupled due to several mechanisms, such as self-weight pressure, heat of hydration and suction development as a result of self-desiccation. The findings can assist researchers and practitioners to better understand THMC behaviour and thus design more cost-effective CPB structures.

Aug 1, 2013

By Matej Petružálek, Tomáš Svitek, Tomáš Lokajícek

"Migmatite from the Skalka region (Czech Republic) was chosen as the experimental rock material. It has macroscopically visible plane parallel structure (foliation). The foliation was caused mainly by biotite grains arrangement. The cylindrical samples of migmatite with subhorizontal, subvertical and oblique foliation were uniaxially loaded up to the failure. Network of 8 broad band sensors was employed for acoustic emission monitoring and ultrasonic sounding. A grid search method with anisotropic velocity model was used for AE hypocenters localization. The source types of successfully localized events were determined from the average first arrival amplitude. Structural anisotropy of tested rock material caused the anisotropy of its mechanical properties (peak strength, Young’s modulus) as well as a different way of fracturing process in dependence on the angle between axial stress and foliation plane. The combination of splitting, shearing and sliding was found to control the fracturing of sample with subhorizontal foliation. The shearing and sliding was dominant in fracturing of samples with oblique foliation. With greater dip of foliation, the role of sliding increased at the expense of shearing. Due to the favorably oriented system of microcracks already present, the shearing and splitting was at the same level during fracturing of the sample with subvertical foliation before nucleation began.INTRODUCTIONThe process of failure of low porosity rocks depends on their mechanical properties and actual stress and temperature condition. At the low pressure and low temperature, the most common way is brittle failure, which is a progressive process requiring the initiation, growth and coalescence of cracks (Lockner, 1993). Stress strain behavior of low porosity crystalline rocks, during the laboratory compression experiments, is divided into four characteristic stages: crack closure, elastic region, stable crack growth and unstable crack growth which leads to the brittle failure, Brace et al. (1966) , Bieniawski (1967), Lajtai (1974), Cai et al. (2004), Nicksiar and Martin, 2012 and 2013.The fracturing process of stressed rock begins with the crack initiation (sci), which for low porosity rocks occurs approximately at 40-50% of peak strength (sp) (Cai et al., 2004; Nicksiar and Martin, 2013). After the sci, the dilatancy begins and stable crack growth follows up to the crack damage threshold (scd), which is approximately at 80% of sp (Cai et al., 2004). After crossing the crack damage level, there is an unstable crack growth accompanied with nucleation of fault plane (sn) at 97-100% of sp. (Rao et al., 2011). The stress drop accompanied with formation of macro scale shear failure plane follows after peak stress is crossed."

Jan 1, 2015