Search Documents

By Nobuhiro Kuriyama

Electrochemical activation behavior of an AB2-Laves-phase type hydrogen storage alloy, Zr0,9Ti0.lNi1.lCo0.1Mn0.6V0.2 was studied to make clear activation process of pellet-type metal hydride electrodes. An alkaline treatment of the electrodes with heated alkaline solution gave alloy surface enriched with nickel, and the treated electrode was more easily activated. The treated electrode desorbed more hydrogen during the first charge-discharge cycle, and was activated without induction period. A cross sectional view of the activated electrode showed finer pulverization of alloy particles than the annealed alloy, and impedance spectroscopy indicated larger surface area of the electrode using the as-cast alloy. Since the as-cast alloy contains inhomogeneities, multi-phase microstructure and stress in the particle, the finer pulverization of alloy particles with hydrogenation are considered to increase surface area in an earlier cycle in the case of the as-cast alloy, which leads larger reaction area and faster activation of the as-cast alloy electrode.

Jan 1, 2002

By R. N. Reddy

The Pseudo capacitance of layered type Mn02 electrode material for electrochemical capacitors (EC's) was investigated. MnO2 was synthesized in our laboratory. Mn02 was prepared from heating of KMn04 at 300°C in air. Cyclic Voltammetry (CV) experiments were carried out using three electrode system, Saturated calomel electrode as reference electrode, platinum mesh as a counter electrode, and MnOz composite material mounted in a platinum mesh used as a working electrode. Two kinds of composite working electrode materials were used, one was mixture of MnOz and 25 wt% acetylene black, while the other was MnOz, 25 wt% acetylene black and 25 wt% carbon. All the experiments were carried out at 25OC. A maximum specific capacitance of 130 Fig and 118 Fig were observed at the scan rate of 2 mV/s and 20 mV/s respectively in 1M KC1 for composite electrode made with carbon. Results obtained in this study are compared with that of other electrode materials.

Jan 1, 2002

By Haotian Xue

A new process to extracted antimony directly from stibnite concentrate by reductive sulfur-fixation smelting in sodium molten salt has been presented. The influences of sodium salt content and composition, ferric oxide addition, temperature and time was investigated, respectively. The optimum conditions was determined as follows: W????: ??concentrate=40%, W??alt: ????concentrate =88.75%, WFe2O3 :Wconcentrate =55.13%, W??aCl: ????alt=40%, 1123K, 1h. Under above-mentioned optimum conditions, the average direct recovery ratio of antimony can reach 91.48%, and the main chemical composition of obtained crude antimony is Sb 94.31%, Fe 4.436%, Pb 0.502%, Au 0.0236%. In comparison to traditional antimony pyrometallurgical process, the smelting temperature of present process is reduced from 1423~1473K to 1123~1173K. During the smelting operation, SO2 emision can be avoided completely due to sulfur-fixation as FeS. Furthermore , S0 can be obtained when the molten slag is handled by water leaching with conditions of 323K, L/S=5/1, 2h.

Jan 1, 2014

By Toyohisa Fujita

The effect of variables on the gold extraction with ammonium thiosulfate was investigated on sponge gold and ore samples. The Effects of CUS04, (NH4hS203, NH40H, (N~hS04' pH, stirring speed and retention on gold leaching rate and thiosulfate oxidation (consumption) have been studied. Almost 100% of gold was leached from sponge gold and over 96% from ore sample at optimum conditions. Trioctylmethyl ammonium chloride was used to recover gold from thiosulfate pregnant solution. It was found that more than 99% of gold was recovered by the extractant diluted with n-octane at 01 A ratio of 1: 1 without the re-adjustment of pH or others. Also, the gold cementation was conducted without de-aeration by using zinc, copper and aluminum powders. The result indicated that the gold was effectively recovered from a solution of low ammonia and copper concentrations and higher thiosulfate concentration. The gold recovery process by using ammonium thiosulfate is an environmental friendly method comparing to conventional cyanidation process.

Jan 1, 2003

By Hai-Peng Guo, Lu Jiang, Xiao-Man Yan, Bing Xie, Hong-Yi Li

Traditional, calcium compounds cannot be used in vanadium extraction processing due to the limitation of sodium roasting technology, which results in unsatisfied dephosphorization for vanadium-containing hot metal in converter and thus increasing the dephosphorization burden for subsequent steelmaking. The calcium roasting technology is an alternative for vanadium extraction and allows adding lime into vanadium slag in converter. In the present study, vanadium was leached by soda from roasted vanadium slag with high calcium content. Effects of roasting temperature and time, leaching temperature, Na2CO3 concentration andliquid to solid ratio on vanadium leaching rate were studied. The results show that 94% of vanadium was extracted by roasting the vanadium slag at 950℃ for 2.5h and then leaching in 160g/L Na2CO3 liquid at 95℃ for 1h with liquid to solid ratio of 10:1 ml/g. Impurities of Si and P reacted with calcium and formed insoluble Ca2SiO4 and Ca3(PO4)2 respectively.

Jan 1, 2015

By Toshiyuki Nohira, Eiichi Takeuchi, Tetsuo Oishi, Hideki Ono, Hirokazu Konishi

The Dy-Nd-Pr-Ni alloy sample was prepared by cathodic potentiostatic electrolysis at 0.65 V (vs. Li+/Li) for 1 h using a Ni plate in a molten LiCl-KCl-DyCl3-NdCl3-PrCl3 system at 723 K. The highest mass ratio (Dy/Nd+Pr) in the alloy sample was observed to be 50 at 0.65 V. Anodic potentiostatic electrolysis at 2.20 V for 12 h was conducted using the Nd-Fe-B magnet electrode in a molten LiCl-KCl system. All elements were almost dissolved from the magnet, and the original form of the magnet disintegrated. After anodic potentiostatic electrolysis at 2.20 V, cathodic potentiostatic electrolysis was conducted at 1.00 V for 5 h using a Mo plate in order to remove the dissolved Fe from the bath. Finally, cathodic potentiostatic electrolysis was conducted at 0.65 V for 12 h using a Ni plate. The mass ratio of Dy/Nd in the alloy sample was determined to be about 18.

Jan 1, 2015

By Mahmood Alemrajabi

When LKAB processes their iron ores in northern Sweden, they generate apatite as a by-product. The apatite has been recovered by flotation and the concentrate contains about 0.4 wt% rare earth elements (REE). Both phosphate rock and REE are listed as critical raw materials for the European union. In the present study, the recovery of REE within the nitrophosphate process of fertilizer production has been studied. In the first stage, the REE are precipitated and isolated as a phosphate concentrate. For further purification and individual separation of REE by solvent extraction, removal of phosphorous from the concentrate to enhance the dissolution of REE in mild acidic solutions is essential. In this study, thermal treatment of the concentrate with sodium hydroxide at elevated temperatures followed by water leaching has been studied in order to separate the phosphorous and thereby facilitate dissolution of the REE. The results show that 95% of total phosphorous initially present in the REE phosphate concentrate is removed after thermal treatment with NaOH 1:1 mass ratio, at 400 °C.

By Hiroshi Nakazawa

An acid mine drainage in abandoned Horobetsu mine in Hokkaido, Japan, contains arsenic and iron ions; total arsenic ca.10ppm, As(III) ca. 8.5ppm, total iron 379ppm, ferrous iron 266ppm, pH1.8. Arsenic occurs mostly as arsenite (As (III)) or arsenate (As (V)) in natural water. As(III) is more difficult to be remove than As(V), and it is necessary to oxidize As(III) to As(V) for effective removal. 5mL of the mine drainage or its filtrate through the membrane filter (pore size 0.45m) were added to arsenite solutions (pH1.8) with the concentration of 5ppm. After the incubation of 30 days, As(III) was oxidized completely with the addition of the mine drainage while the oxidation did not occur with the addition of filtrate, indicating the microbial oxidation of As(III). In this paper, we have investigated the microbial oxidation of As(III) in acid water below pH2.0.

Jan 1, 2006

By Katsunori Yamaguchi

The zinc, lead and alumina contents in copper smelting slag are increasing with the increase in waste recycling. The recovery of base metals such as lead and zinc from copper converter slag is important from both an economical and environmental perspective. As a fundamental study of the metal recovery by reduction process, activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag under iron saturation at 1573K are derived from the data of slag-metal equilibrium experiments. On the basis of the obtained data, the activity coefficients of ZnO and PbO in the CaO-SiO2-FeOx-5mass%AlO1.5 slag were compared with those of the CaO-SiO2-FeOx ternary system. Addition of alumina increases activities coefficient of ZnO and PbO in SiO2 rich side of the slag, and decreases them in CaO rich side.

Jan 1, 2006

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By Bora Derin, Sertac Yazici, M. Seref Sonmez

"In this study, the recycling conditions of waste liquor obtained after the production of tungsten boride powder from calcium tungstate by self-propagating high temperature synthesis (SHS) and the following hydrochloric acid leaching were investigated in detail. Environmentally unfriendly and extremely acidic (pH~ -0.3) liquor consisting of calcium, magnesium, and boron ions was treated with 1 M sodium carbonate solution to precipitate magnesium carbonate and calcium carbonate phases. The obtained amorphous precipitates were heated up to the temperature of 400°C for re-crystallization. As a result, MgO, CaC03 and CaMg(C03)z phases were obtained, while sodium, boron, chlorine ions were remain in the solution. The present study is still in progress.IntroductionSelf-propagating high temperature synthesis (SHS) is one of the techniques used in the production of a variety of advanced ceramics, inter-metallic, organic and inorganic compounds, oxygen free single crystals, and polymers [ 1, 2]. The reaction becomes selfsustaining and propagates in the reactant mixture, after initiation in SHS process. SHS products may contain the mixture of several unwanted compounds and elements. Therefore following acidic leaching process may be needed to purify the target product. In the previous study, calcium tungstate (Ca W04), magnesium (Mg) and boric acid (B20 3) mixture were reacted to produce tungsten boride powder by SHS process according to the Reaction 1. Then, magnesium and calcium containing byproducts (i.e. MgO, Mg3B206 and Ca3B206) found in the SHS product were leached out by using concentrated hydrochloric acid (HCl) solution to obtain pure tungsten boride powder [3].Ca W04 + 0.5B203 + 4.5Mg = WB + 4.5Mg0 + Cao (1)After the leaching, filtrate solution consisting of different amounts of magnesium, calcium, and boron requires additional treatment for the environmentally acceptable disposal.Several works were carried out about magnesium precipitation conditions and kinetics from brines. Rabadzhieva et al. investigated the precipitation of Mg(OH)z from brines by using NaOH as well as caustic soda [ 4]. Turek ve Gnot investigated the precipitation efficiency of Mg(OH)z for the temperature range between 10-40°C, while the reaction was kinetically experimented by Alamdiri et al [5, 6]. Homogeneous precipitation of nesquehonite (MgC03.3H20) by the reaction of MgCli with (NH4)2C03 in supersaturated solutions and factors that influence the precipitation of MgC03.3H20, such as reaction temperature, initial concentration, stirring speed, titration speed, equilibration time, have been studied by Wang et al [7]. The precipitation of Mg(OH)z by calcium hydroxide from aqueous solutions was studied by Baird et al. [8]. Stratful et al. focused on conditions influencing the precipitation of magnesium ammonium phosphate from wastewaters [9]. 1031"

Jan 1, 2011

By H. Hirayama, T. Okura, O. Kato

"Saganoseki Smelter & Refinery, one of the largest copper smelters in the world, has the annual capacity of 300,000 metric tons in copper content with two flash furnaces, six Pierce-Smith type converters, two anode furnaces, four acid plants, three tank houses and perfect pollution control system.Coping with the many severe conditions surrounding the copper industry in the last decade, Saganoseki Smelter has kept performing the stable operation, while enhancing the smelting capacity and developing new technologies such as the hydrometallurgical treating of converter dust recovered at electric precipitators. Especially in the operation of flash furnaces, which are of Nippon Mining's conversion type using hot air in a temperature of l,000ºC some technological improvements and complete operation control factors have approved the concentrate feed rate to reach to 2,200 tons a day for a flash furnace.Reported in this paper are the production control design for copper smelting process, and the operation control scheme of the flash furnace following the brief review of the characteristic of Saganoseki Smelter's process and some improvements. Copper Smelting ProcessDescriptions of major unit operations and general specifications of the copper smelting facilities are summarized in Table 1, and the present flowsheet of the copper smelting is described in Figure 1 (1,2).Outputs and raw materials treated in the last five years are shown in Table 2, in which concentrate includes powder copper scrap which amounts to 3 to 4% of concentrate.A full operation was performed for a period of one month, for both one flash furnace operation and for two flash furnace operation. With one furnace operation, 19,200 tons of copper were produced. With the two furnace operation, 84,000 tons of concentrates were charged and 33,500 tons of anode (net 28,600 tons of copper) were produced.The actual production level, however, has been kept at 80 to 90% of the full capacity because of low copper price, tight market of copper concentrate or fall of net demand in Japan."

Jan 1, 1989

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By Marcela C. Santini, Luiz A. Teixeira

"Surface conditioning (also referred as etching) of plastics prior to metallization is generally conducted with sulfuric I chromic acid solutions. Although these baths perform well technically, the presence of Cr (VI) imposes serious operating problems of an environmental nature. The present work reports ·the results of a study of surface conditioning o(ABS using solutions based. on sulfuric acid, with hydrogen peroxide and/or nitric acid, replacing chromic acid, as oxidants. Process performance was evaluated by SEM and by the uniformity and adherence of electroless nickel coatings applied on selected conditioned samples. The results showed that the evaluated types of solutions could be optimized to perform as well as the chromic-based baths, with a much superior environmental quality.IntroductionMetallization of plastics is normally undertaken for either decorative or functional purposes. Through metallization, the specific properties of plastics such as light weight, design flexibility, and low-cost of manufacturing are enhanced by the addition of properties usually associated with metals. These include reflectiveness, abrasion resistance, electrical conductivity, and a variety of decorative effects (1).The available processes that can be used for metallization of plastics are vacuum metallization or vapoµr deposition; indirect metallization and plating (1). Plating can be sub-divided into electroless plating and electroplating. In electroless plating, metal ions in aqueous solution are deposited on the .activated plastic surface by oxi-reduction reactions without the aid of an external electric potential, forming a thin metallic layer. This electroless deposited film has two functions: (a) it provides an electrically conductive substrate that allows further coating by electroplating; and (b) provides a secure bond between the plastic substrate and the electroplated layer (1,2). In case the electroless metallic part requires an additional layer for finishing purposes, or just an increase in thickness, the part can be additionally electroplated with a· variety of metals - in most cases those are copper, nickel or chromium (3)."

Jan 1, 2000

By C. A. Nogueira, F. Pedrosa, F. Margarido, R. N. G. Guerra

"A hydrometallurgical process for recycling spent Zn-MnO2 batteries was developed, involving leaching with sulfuric acid, purification by precipitation and metals separation for further recovery. Leaching of zinc oxide was easily attained while for manganese oxide was rather difficult depending on temperature and acid concentration. At 90°C and with the liquid/solid ratio of 20 L/kg, more than 95% of zinc is recovered in 30 minutes with 0.5M H2SO4. To attain similar recovery for manganese, higher levels of acid concentration and time are needed (e.g 0.7 M and 2 hours). After leaching a purification step is necessary to remove iron co-dissolved through Fe(III) precipitation. Separation of zinc from manganese by solvent extraction with 1M DEHPA follows in the process route. The countercurrent multistage separation diagram developed allows the production of a zinc electrolyte with 120 g/L Zn and 0.005 g/L Mn, and a raffinate with 16 g/L Mn and 0.013 g/L Zn.IntroductionThe recycling of spent Zn-MnO2 batteries is carried out by dedicated recyclers using several process alternatives [1]. Most of the running processes use pyrometallurgical technologies [2] based on zinc distillation. Alternative treatments by hydrometallurgy have been reported [3-5] but its application is scarce.In order to contribute to the development of alternative solutions, a process for recycling batteries based on Zn-MnO2 systems has been studied. The process is based on the hydrometallurgical treatment of spent batteries in sulfuric acid media (Figure 1). The process starts with the physical processing by shredding using cutting grinders, where the batteries are opened and size reduced, allowing the liberation of the interior electrode particles or pastes. The fines can be then separated and the coarse material containing the steel scrap can be treated to remove the remaining aggregate electrode. The final scrap also contains some plastics and other non-metal materials and can be further valorized."

Jan 1, 2008

By Sijun Li, Bingyu Zhang, Haitao Zhou, Zhendong Zhang, Guofei Si, Xianghua Liu

"Hot compression test of Nb microalloyed coiled tubing steel is performed on Gleeble3500 at 1123K—1373K and strain rate from 0.001 to 5s-1. It is found that flow softening occurs and the flow curves exhibit a peak with a characteristic of dynamic recrystallization (DRX) and change with temperature and strain rate significantly. The peak stress and peak strain are dependent on the Zener-Hollomon relationship with activation energy of 390 KJ/mol. On the basis of Avrami equation and the Zener-Hollomon parameter, it is obtained that the dynamic recrystallization kinetics equation with which the calculated and measured recrystallization fraction is very close. On the results of hot compression test, the Nb microalloyed coiled tubing steel is rolled by Thermo-Mechanical-Control-Processing (TMCP), and it is obtained that the yield strength and tensile strength of Nb microalloyed coiled tubing steel are 565MPa and 685MPa respectively, and the elongation percentage is 30.1%.IntroductionCoiled tubing is widely used in oil field for well logging, well completion, drilling, work over and other operation in various fields to solve a number of conventional operating techniques problem which are difficult resolved, and it plays a more and more important part in exploration and production at oil field. [1] It will improve the efficiency of exploration and exploitation, studying, developing and using coiled tubing technology. Therefore, the development of domestic coiled tubing materials and manufacturing technology are great significance. It is well known that Coiled tubing has relatively poor working conditions and complex force state. So, the coiled tubing needs satisfier a kind of high strength, high plasticity, and corrosion resistant under complex oil gas condition. As the coiled tubing technology developed, the level of the coiled tubing steel is from CT55 originally to CT90 and CT100, and the corresponding tensile strength is 483MPa-758MPa. [2, 3]"

Jan 1, 2012

By Shirley Cosin, Guillermo R. Martín-Cortés, Francisco R. Valenzuela-Díaz, Jorge E. Di Rito, Valquiria F. J. Kozievitch

"A procedure that is being studied as a potential method for correct disposal of industrial wastes by incorporation on common clay bodies in the fabrication of structural ceramic products as bricks, blocks and roof tiles. The objective of this paper is to present the results obtained with mixtures of unburned sanitary ware wastes with a common clay from Jundiai, São Paulo, Brazil. Preliminary tests of incorporation (1,0% to 30,0% in weight) were made with hand formed spherical test bodies. With the proportion that presented spheres with the higher compression strength after drying and after firing (950°C) prismatic samples were extruded. Based on the ceramic properties of those mixtures an industrial test was performed. Six hundred hallow blocks containing 30% waste were fabricated and presented ceramic properties similar to those without incorporation. Introduction The sanitary ware segment has a very great prominence in South America, placing Brazil as one of the greater producers of the world.. Inside the country, the city of Jundiai, in the State of São Paulo is the greater producer region of this ware. Great part of the material is destined to exportation and daily it is produced high number parts. High exportation requirements make that the amount of powder waste rejects reach astronomical volumes. Until the moment too small part of that material it is re-taken with advantage, because in the own segment, there is not an economic viability, by the fact of the exigencies concerning the quality of the final product [1]. If from one side it exists that material that at the moment is deposited in landfills, or stored at the patio’s factories, from the other side the exigency of adopting exploitation rules, recycling and obedience to Laws relative to the environment as ABNT 10400, therefore it is a material that if well studied, it will certainty have a noble destiny [1]."

Jan 1, 2008

By Suman Das, Justin J. Gambone, Rohan Bansal, Ranadip Acharya

"This paper focuses on modeling of the scanning laser epitaxy (SLE) process that is currently being investigated and developed at the Georgia Institute of Technology. SLE is a laser-based manufacturing process for the creation of equiaxed, directionally solidified and single-crystal deposits of nickel superalloys onto superalloy substrates through melting and resolidifícation of alloy powders using a scanning laser beam. The thermal modeling of the system, done in a commercial CFD software package, simulates a heat source moving over a powder bed and dynamically adjusts the property values for consolidating CMSX-4 nickel superalloy powder. The associated melting and re-solidification process is modeled using an immediate consolidation approach, and the predicted melt depth is compared with the experimental data obtained. For a given position of the beam, geometrical parameters of the melt pool are used to estimate the resulting microstructure. The influence of the processing parameters on the microstructural evolution is also discussed. This work is sponsored by the Office of Naval Research through grants N00173-07-1-G031, N00014-10-1-0526 and N00014-11-1-0670.IntroductionIn order to increase the operating temperature of gas turbine aero engines, investment cast equiaxed turbine airfoils are now often replaced with airfoils that have either directionally solidified columnar or single crystal (SX) microstructure. Wear and damage during operation limits the lifetime of these components and necessitates the replacement of numerous airfoils within the engines. Due to the high cost of producing SX cast turbine blades, the cost of replacing each blade can be several hundred to several thousand dollars. With each engine containing several hundred blades, the cost to replace all blades can reach hundreds of thousands of dollars. Hence, it is of great interest to develop a process that can restore the single crystal microstructure at the locations of material loss and allow for the blades to be repaired and reused rather than be scrapped and replaced."

Jan 1, 2012

By Hee Dong Jang, Hong Yong Sohn, Miguel Olivas-Martinez

"Tetramethylorthosilicate (TMOS), a precursor of silica nanoparticles, is prepared from the waste silicon sludge, followed by the synthesis of silica nanoparticles from the TMOS by flame spray pyrolysis. A two-dimensional multiphase computational fluid dynamics (CFD) model for the flame spray pyrolysis process (FSP) for the synthesis of silica nanoparticles has been developed. The model incorporates the governing turbulent equations of overall continuity, momentum, energy and species mass transport to represent the gas phase and the population balance model (PBM) to account for the silica nanoparticles. The model has been validated with experimental data in terms of gas temperature and average particle size. Introduction Silica (SiO2) nanoparticles are used in various industrial applications, such as catalyst, pigments, thin film substrates, electronic and thermal insulators, and humidity sensors [1]. They are also used as additives in plastics and rubbers to improve the mechanical properties of elastomers, and in liquid systems to improve their suspension behavior. These applications rely on the particle morphology, average particle size, particle size distribution, and phase composition [2]. Silica nanoparticles can be synthesized by wet chemical processes such as sol-gel methods and high-temperature processes such as flame spray pyrolysis (FSP). The FSP process provides a unique control of particle size and crystalline structure and it can also produce high-purity, thermally stable particles continuously with minimal further treatments. The sizes of the flame- made particles range from a few to several hundred nanometers, depending on the operating conditions [1]. The synthesis of silica nanoparticles from organic compounds that contain silicon by the FSP process is of interest because it generates no harmful by-products [1, 3]. Several compounds such as tetraethylorthosilicate (TEOS) and tetramethylorthosilicate (TMOS) can be used to synthesize silica nanoparticles, but most such compounds are expensive. Thus, it is desirable to prepare the precursor compounds from waste materials. In the present study, TEOS and TMOS synthesized from silicon sludge were used as precursors of silica nanoparticles [4]."

Jan 1, 2008

By Anestis Vlyssides, Elli Maria Barampouti, Sofia Mai, ?postolos Vlyssides

"A new anaerobic reactor variation, the UASB/CO2-stripper reactor was conceived. It consisted of a conventional UASB reactor that recirculated the biogas produced. The sludge characteristics of this system were examined when treating high strength wastewater. From the data collected, it was obvious that the UASB/CO2-stripper system can satisfactorily operate at higher loading rates (25 g COD·L-1·d-1). A pronounced effect on the quality of the granular sludge was observed. The VSS/TSS ratio decreased sharply. A considerable decrease in the mean granule diameter was observed, while the specific gravity of the granules increased. The sludge bed porosity increased significantly leading to a considerable expansion of the sludge bed. These changes in the sludge properties led to a gradual shift of the system towards a fluidized bed process as far as its hydraulic characteristics were concerned.IntroductionIn recent years energy considerations and environmental concerns have increased the interest in direct anaerobic treatment of industrial wastes. The anaerobic method of waste treatment offers, under the present circumstances, a number of significant advantages with trivial or more serious drawbacks over other treatment methods. The major obstacle to the application of the process for this specific purpose is perhaps the difficulty of extending it to a stable and simple operational form. A number of reactor configurations has been developed leading to high biomass concentrations, e.g. the contact process, the filter reactor, the UASB reactor, and the fluidized bed systems, but the process stability problem still remains [1].A prime objective in the operation of anaerobic waste treatment process is the maintenance of a proper pH range. Thus, a possible solution to the process stability problem could be obtained by increasing alkalinity in the anaerobic systems. Therefore, the main objective of this paper is to present and evaluate the results of a system (UASB/ CO2-stripper) with increased alkalinity concentrations."

Jan 1, 2008