Search Documents

By Barry C. Roth

A Real Time Automated Remote Reading Electrolytic Tilt Monitoring System was effectively deployed for monitoring an existing five story brick building during underpinning, shoring and excavation operations for a directly adjacent thirty-foot deep excavation. The monitoring system was comprised of four sets of uniaxial electrolytic tilt meters connected to a Campbell datalogger with multiplexer, cellular modem and solar power. The excavation was for the foundation and underground parking as part of a new 55 story tower complex. Challenges to the contractors and to our monitoring personnel which were addressed included a tight urban site contemplating property line to property line new construction with directly adjacent old existing buildings, buried concrete foundations from former site use, cohesionless pervious sandy soils and high groundwater. Highly variable and diurnal ambient temperature regimes due to adjacent building shadows required careful corroboration and application of temperature corrections to the raw data. Earth tides were suspected on a very small scale and investigated by correlation between the data and the local sinusoidal tidal ephemera. Incidental inadvertent contractor interference with the instruments during underpinning due to site constraints was readily detected.

Jan 1, 2007

By J. H. Qian

China is one of the countries with comparatively wide distribution of soft soil. In the wake of the rapid developement in the national economy and construction, the improvement technique of soft soil foundation has been perfected gradually. At the present, an integrated system of soft soil improvement has formed, features of such a system are shown by the variety of improvement methods, the complement of theoretical study to project practice. This paper summarizes mainly the following methods: lime column, vertical drain, vibroflotation and dynamic consolidation.

Jan 1, 2010

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By R. K. Filip

"Steel bearing piles have long been used to carry high compressive, tensile and lateral loads. Such piles are most commonly tubular or ""H"" profile and are typically installed using percussive techniques. The noise and vibration associated with such installation techniques tends to preclude the use of steel bearing piles in urban and other sensitive areas.This paper describes the design and construction of an innovative new road bridge in Milton Keynes, UK. The steel bearing piles were required to continue out of the ground to form the bridge columns and abutments and then be cast directly into the soffit of the reinforced concrete bridge deck. This project was to be the first time in the UK, that this form of bridge design had been used.The paper shows how new installation techniques allowed the designers to use these high capacity steel elements in a sensitive urban environment without the use of percussive or vibratory installation techniques. Finally the paper shows how these quiet and vibration-less installation techniques can be extended to other applications.A UNIQUE BRIDGE SUPPORTED ON ""BOXED SHEET PILES""CONCEPT HISTORYThere are over 700 bridges in Milton Keynes. Concrete is the dominant construction material, most are single span with massive parallel wing wall retaining abutments. All have a certain uniformity of aesthetic design. Pell Frischmann Consultants Ltd (PFC) proposed to the client, English Partnerships (EP), that an ""integral bridge"" with a slender open appearance would be an appropriate aesthetic form for a new highways bridge, within the district of Westcroft (figure 1). The concept required that the bearing piles be continued up out of the ground to form the bridge columns and abutments. Four rows with four piles in each row were suggested. Each would then be cast directly into the reinforced concrete bridge deck forming a moment connection (figure 2). This concept meant that a single continuous steel structural member would replace traditional reinforced concrete bored piles, pile caps and piers. This member would carry vertical and lateral loads. The conceptual design was intended to meet the following client requirements:"

Jan 1, 2005

By Han Jie

The results of full scale plate load tests on stone columns on soft clay in coastal areas are presented in this paper. Four load tests were made, two of which were performed on the ground treated with stone columns, one on an isolated stone column and the last one on the untreated ground. For a given stress range, the settlement of the rigid plate, the stress concentration factor, and the excess pore water pressure were measured. It is found that the distribution of vertical stress beneath the rigid plate supported by the composite ground of stone columns is very different in shape from the one by the untreated ground, that the stress concentration factor has a relation with the stress level and time, that the stone columns increase the bearing capacity up to by 2 times, and that the ground stabilized by stone columns is of great advantage to keep the foundation stable.

Jan 1, 1991

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Gordon King

This paper presents a case study of large diameter continuous flight auger (CFA) piles and drilled shafts utilized for foundation support of a series of heavily loaded cement plant structures at the Suwannee American Cement (SAC) Plant in Branford, Florida. The high loads and exacting total and differential settlement criteria when combined with a highly variable subsurface geology provided a challenging design scenario. Fully instrumented static pile load tests were performed to determine design parameters in the variable weathered limestone bedrock. Ultimate side friction values ranged from 2 to 8 tsf within the limestone, resulting in the requirement for CFA piles up to one meter (approximately 40 inches) in diameter and socket lengths of up to 40 feet. At several localized areas, the limestone bedrock was in excess of 60 feet below grade, requiring the use of cased drilled shafts to depths on the order of 80 to 90 feet. An integral part of the production pile installation was the use of instrumentation to monitor drilling and concreting parameters. Calibration of drill rates, torque and auger rotation with rock quality was performed to allow monitoring of the soil stratigraphy at each pile location. When combined with the results of the instrumented load testing, the monitoring of drilling parameters allowed confirmation that sufficient socket length was achieved within the quality of rock present at each and every pile location.

Jan 1, 2003

By Franz-Werner Gerressen

New developments are required each day as our industry becomes more competitive. To improve performance, continue and to ensure future demands can be met. This requires the development of technical support systems that enable a more constant delivery and quality of installation of pile foundations and other applications. For example: assistance systems capable of relieving the machine operator of automating monotonous or repetitive operations. Real time installation control of the production process to manage quality control, or data transfer and reporting systems capable of keeping pace with the digital future. This paper will describe these new approaches and considerations required for these new developments. The paper also describes the equipment which is needed to execute the work under the various conditions and provides references herein. INTRODUCTION The success of a construction site is influenced by a number of factors. Selecting the most efficient and economic methods during the planning phase to defining the right direction. This means having multifunctional equipment available. To ease the usage of this equipment by the operator, uniform operation and control systems are essential. Systems like this can provide uniform handling procedure for more than 20 different installation techniques. Experienced operators are not always available. Therefore, to ease the start for beginners and to support training, numerous assistance systems were developed. This ranges from simple information for controls shown on the monitor avoiding misuse to systems which can partly automate the construction process. Regardless, the best equipment is not enough when the construction is not running smooth. The control system not only helps to organize and coordinate service of the equipment; moreover, it allows the operator to control the quality during the installation process reacting if needed. It allows process optimization as well as documentation which might be required for later negotiations.

Jan 1, 2019

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By Glen Mann, H. G. Vestberg, Robert D. Holtz

"Underpinning of residential and commercial structures is often accomplished using a number of driven-in-place small diameter steel pipe piles. These piles, at least in the Seattle area, are typically described as pin-piles and are driven with an air compressor operated jack hammer to a refusal criterion developed from an empirical basis. Over the past twenty years or so, the materials have improved in quality and strength, and the driving equipment has improved in efficiency and capability. These improvements have resulted in damage to the pin-piles during driving as well as to the driving equipment. The primary objectives of this load testing study were to develop a relationship between the driving penetration resistance of 2-inch diameter pin-piles and the ultimate bearing capacity when piles were driven at different penetration rates and, based on the load test results, to develop an opinion regarding an increase in the allowable axial load capacity [ultimate load capacity divided by a factor of safety] of a 2-inch diameter pin-pile over the currently used permissible load capacity of 4 kips in the Seattle area. Also, if feasible, a reduction in the present driving penetration rate was to be recommended to help reduce the rate and magnitude of pile and equipment damage whilst maintaining the allowable load capacity. The recorded ultimate bearing capacities were also compared with the Tagnent-line and the Davisson analytical methods in an effort to determine if either of these provided a reasonable determination of the pile load capacity.IntroductionThis paper describes the results of a series of load tests performed on small diameter, 2-inch, driven-in-place steel pin (pipe) piles and based on these results, provides the support for a modification to the presently used allowable axial pin-pile capacities.The intent of the load testing program was to determine how much influence the penetration resistance might have on the individual piles' ability to support the allowable axial load without undergoing any significant vertical deformation. For the purposes of this paper the ""allowable load capacity"" is considered to be the ultimate pile load capacity divided by a minimum factor of safety, typically considered to be 2.0 in this area. A pin (pipe) pile comprises an open or closed ended, schedule 80 steel tube which is driven-in-place, usually with an air compressor operated 90 pound pneumatic jack hammer. These jack hammers typically operate at a rate of about 1,200 blows per minute, (Haggard, Holtz and Mann, 2001 )."

Jan 1, 2005

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By Bernardo J. Jiménez, Harlem Lora, Roberto Acosta Mora

Circunvalacion Norte project is currently the most important infrastructure project in Costa Rica. It is the last segment of the urban perimeter highway. Site investigation of local geotechnical conditions were studied by SPT, CPT, pressuremeter tests and boreholes. A static load test was executed as a proof test with an associated ultimate resistance of 12056 kN (2710 kips). Drilled shaft design was done using PMT tests and axial nominal resistance varied between 4000 kN (900 kips) and 6000 kN (1350 kips). A total of 416 drilled shafts were constructed in 15 months with drill performance of 32 m/day (105 ft/day). Drilled shaft lengths varied between 4,0 (13 ft) m and 40,0 m (130 ft). Selfconsolidating concrete was used to achieve an adequate workability even in high densities rebar cages. Several site conditions proved the importance for maintenance of the working platform, predrilling of rock sockets and having spare parts to avoid increase in project’s cost. New procedures were taken to prevent concrete segregation on excavations near underground water flow. Monitoring the quality of the shafts from CSL test showed less than 3% of the shafts presented a considerable anomaly, which proved that the adopted construction method and materials were adequate. For the concrete anomalies, successful remediation was performed by means of grout at the base of the shaft with two different types of drilling methodology depending on the concrete anomaly.

By Gregory A. Stephan

A case history of design, prediction, instrumented static load tests on probe piles, installation monitoring, and integrity testing of production piles is presented. Based upon project-specific subsoil conditions, as obtained from several 60 to 80 ft (18.3 to 24.4 m) deep test borings, deep foundation system alternatives included driven concrete and steel pipe piles as well as augered cast-in-place (ACIP) piles. High structural loads, site-specific constraints, and the production time frame mandated by the project owner led to the selection of an ACIP pile foundation system that was designed for a pile capacity of 75 tons (667 kN) in compression and 35 tons (309 kN) in tension. Site-specific concerns were raised about the highly porous nature of fragmented and decomposed sandy limestone as well as the high grout intake during construction that could result in increased foundation cost as well as interconnecting of the piles in the rock layer. Consequentially, a multi-phase ACIP pile evaluation program consisting of instrumented compression pile load tests, in conjunction with single-hole ultrasonic pile testing, pile echo testing (sonic testing), as well as full-time production pile monitoring by an experienced geotechnician was specified. As a result of this testing and evaluation program, while grout usage was determined to be within an acceptable range, the instrumented compression load tests yielded data that allowed use of 55 ft (16.8 m) long ACIP piles in lieu of the original plans to use 70 ft (21.3 m) long precast concrete piles. This information was effectively utilized as part of the overall quality control program to install a total of 268, 14 in. (356 mm) diameter ACIP piles within the building footprint to depths of 55 ft (16.8 m) below the pile cut-off elevation as part of the foundation support system. Information recorded during installation included rate of insertion/extraction of the auger, grout pump strokes and pressure, total grout volume, and grout factors, as well as quality and strength of grout. Additionally, many pre-selected installed piles were tested for integrity with a Pile Integrity Sonic Analyzer (PISA) using both sonic and ultrasonic methods. This engineered, monitored, and tested foundation solution provided an effective and quality intensive basis for completion and approval of the foundation work for the building that resulted in cost savings over other foundation alternatives for the owner.

Jan 1, 1999

By Yong Jingrong

Based on the results of several test socketed piles in Sichuan, the mechanism of the deformation for a loaded socketed piles is investigated, and the concept of the socketed effect is proposed. The bearing capacity and settlement of socketed pile are controlled directly by socketed effect, that is an important mark different from the other types of cast-in-situ piles. According to the analysis of this effect and factors interferring it, their roles are discussed with the results of test piles. In order to increase the bearing capacity of piles, the ways and methods enhancing socketed effect are recommended.

Jan 1, 1991

By Denton A. Kort

Historically the visual examination of drilled shafts to determine shape was typically done under dry conditions. Many engineers believe that by using a dry method of construction, the question of shape is minimized because they can visually examine the excavation. In fact, test data suggests that slurry stabilized shafts tend to perform better than similarly constructed dry shafts. Clearly, the uncertainty of the shaft shape is magnified when constructed under slurry. Recent advancements have allowed a mechanical caliper to determine shape in wet conditions, but can be limited by certain shaft anomalies. New sonar technology can determine shaft shape, volume and verticality. The value of sonar technology to the geotechnical and foundation industry at large in terms of quality assurance for clients/owners and quality control for drilled shaft contractors is significant. This presentation will discuss the development and process of sonar calipering technology as it relates to the geotechnical and deep foundation industry. Sonar calipering results presented may include images from the following types of projects: slurry walls, bridge piers, cofferdams and secant walls. The results identify shaft anomalies in a variety of slurry environments, from water and polymer mixes through mineral slurries. Real-time in-situ images and CAD drawings will be presented illustrating the advantages of good caliper data taken during construction. This presentation will appeal to the geotechnical and structural engineers, as well as those supporting the deep foundation industry at large.

Jan 1, 2007

By William Siegel

Kleinfelder provided foundation analysis and design for an expansion to a cement plant in Florence, Colorado. The expansion was a conversion from a horizontal wet process to a vertical dry process, and resulted in the construction of a number of structures with heavy foundation loads. [ ] The field investigation identified old fill and saturated sands and gravels above a shale/limestone bedrock environment. Based upon the anticipated loading, drilled piers socketed into bedrock were recommended. The structures were constructed in accordance with the design recommendations.

Jan 1, 2007

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By Bidjan Ghahreman

A total of 120 micropiles were constructed for foundations of a new selective catalytic reduction (SCR) unit in a coal-fired power plant east of Kansas City, Missouri. Construction was performed under restricted overhead conditions because of the existing facilities. The subsurface profile included about 70 feet of overburden composed of granular fill, stiff to very stiff cohesive material, medium dense sand, and very dense gravel. The bedrock was composed of alternating layers of shale and claystone (weak rock) and limestone (strong rock). It was decided that the bond zone would be entirely in the bedrock. The design rock profile along the bond zone was composed of 10 feet of shale and claystone underlain by 10 feet of limestone, which in turn was underlain by shale and claystone. To achieve the design compression and uplift capacities of 100 tons and 60 tons, respectively, a length of 23 feet was determined for the bond zone. Compression and uplift load tests were performed to verify the design. IBC-2000 elastic line, Decourt (1999) extrapolation, and Chin-Kondner extrapolation were used to interpret the load test results. The interpretation of load test data indicated that both compression and uplift capacities far exceeded the respective design loads. Spring constants of 397 tons per inch (T/in.) (in compression) and 290 T/in. (in uplift) were estimated from load tests at respective design loads. During the compression load test, no sign of creep was observed after the applied load was maintained at the design load (100 tons) for two hours.

Jan 1, 2009

By Subhash B. Bhide

Deep foundations are affected by the presence of sulphates, chlorides, organic contents and water currents present in the soil. The sulphates in soil and ground water interfere first with setting of concrete. In long term, growing of sulphate crystals in concrete, crevices can spall the concrete. The chlorides mainly affect the steel. The organic content does not allow the concrete to set. It also reduces the compressive strength of concrete. The frequency and methods of sampling and testing for above corrosive elements are discussed. Presently available methods to avoid attack due to these corrosive elements are discussed. The stipulations by various codes are summarised. A method to assess the short term impact is elaborated with results of field studies. A tool developed to study the presence and effects of underground water currents on concrete is also discussed.

Jan 1, 1996

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004