Search Documents

By C. Pelley, S. Kelebek, S. Gregersen, P. Katsabanis

A series of small scale tests have been conducted to evaluate the effect of micro-fracture development, imposed by blasting, on the physical properties of the rock as well as its resistance to crushing and grinding. The uniaxial compressive strength, tensile strength, Young’s modulus, Poisson’s ratio, P-wave, S-wave velocity, point load strength index and grinding work index were evaluated for samples without any blasting load and for samples which had received a variety of blast loads, such as a simple side impact from a detonating cord, or combined impacts without any delays and with very short delays. The investigation covered two types of rock, granodiorite and limestone. The effect of blasting load on the physical and rock mechanics parameters of the rock was clearly shown and damage was quantified and related to loading. However the work index did not show significant differences between blasted and not blasted samples, probably due to the relatively low level of impact. Numerical modelling using the AutodynTM code was used to demonstrate damage development in the various configurations tested.

Jan 1, 2003

By Marco Antonio Falquete

A novel spark-generating tube, containing no explosive in its composition, is evaluated and compared with conventional shock tube. The product overcomes a series of problems found in conventional shock tube technology. The technologic development had multiple aims: to avoid transport and storage costs associated with explosives, to be more environmental-friendly, to obtain a high-velocity, hightemperature spark whose thermal performance could overcome poor heat transfer to the delay charge by gas convection at shock tube end, and that could cross barriers such as tight kinks, close knots, cuts, extreme environmental conditions, and long-term hot explosive emulsion exposure. The product of this development is evaluated and compared with conventional shock tube in a series of aspects and performance tests, including spark thermal performance (ignition of tougher, low sensitive delay columns, spark gap test), propagation in critical conditions of use (kinks, knots, cuttings), extreme environmental conditions (long-term exposure to hot emulsion explosive, extremes of cold, heat, moisture, underwater exposure), safety features (ignition through flame, open fire), and security against terrorist acts. Due to the safe characteristics of the tube, a series of demonstrations will be performed during the presentation. In nearly all tests and aspects, the spark-generating tube exceeds conventional shock tube, and in the rest equals shock tube, making it a more reliable alternative.

Jan 1, 2005

By Robert Hivick, Frank Sames

The control of environmental effects, especially blast vibration and airblast, has become a dominating planning criterion for most surface blasting operations. Compliance with existing regulations is generally achieved through constraints in the blast design, or monitoring programs. Commonly, blast vibration and airblast signals are rated and compared by their maximum amplitude and the associated principal frequency. However, this data reduction limits the interpretation of the influence of varying blast design parameters on the vibration and airblast.

Jan 1, 1999

By Eric Kelley

Having been retained as a legal expert for the fatality at the Canberra, Australia project, it made me aware of how good intended blasters profess to be implosion experts. Owners and contractors can be misled by these representations, seeing a video of Directionalized Structures constructed of reinforced concrete may be impressive to watch, but lack sound evidence of the true mechanics of an actual “implosion”; on steel structures more prevalently. If any well intended blaster comes to a determination that he can implode a structure, it should be not be construed he cannot. It should be well investigated that the specific blaster has verifiable experience. What happened in Australia reflects on all end users of explosives. I have heard a direct quote in our project in Alberta, “We don’t want to have what happened in Canberra”. Such a tragedy could have, and should have been avoided. Simple by using the “Right Tool for the Job”. We should sideline egos and economics. Would any competent blaster compromise his or her reputation, company or insurability? More importantly, have an honest conscience knowing that if the proper explosive is available, use it, don’t shortcut it. If possible expand the schedule. Better, yet, examine all avenues before the project, and last, cancel the project. A human life is our best asset and should not be compromised.

Jan 1, 1999

By D. J. Leidel

The offshore production of oil and gas resources has been active in the Gulf of Mexico since Kerr- McGee drilled the first commercial well out of the sight of land in 1947. Since then, approximately 60% of the offshore oil/gas production structures used globally have been erected in the GOM to support the production of energy resources’. The shallow, shelf and shelf edge waters of the Gulf of Mexico have reached or are rapidly approaching production maturity, requiring that the fixed structures used to support energy production be removed or otherwise disposed of by suitable means. The use of energetic materials has been determined to be a safe, efficient and cost effective technology to remove fixed offshore structures whose service life has been exceeded.

Jan 1, 2002

By D Frantzos, J J. Cotter, H Tammemagi, J B. Codrington, J Kaasalainen, A C. Webster

"Exploshres Technologies International (ED) is developing an instrument called ROCSCAN which isplanned to have broad application in both blasting and rock mechanics. The purpose of this paper is to outllne the background that has led to the development of ROCSCAN, describe its objectives and to present a progress report on the work to date. Some of the potential applications of ROCSCAN will also be reviewed."

Jan 1, 1989

By S. Paul Singh

Rock is a heterogeneous medium, a fact often ignored during blast design. In reality, the rock mass characteristics have a controlling influence on the outcome of a blast. If the optimum blasting results are to be achieved over a range of rock mass conditions, it is prudent to understand the role played by the geological features of a rock mass in producing overbreak around the periphery of an excavation. The field work was performed in a drift located in a geologically dominant rock mass and also included observations and assessment of blast damage at several operating mines. The blast damage was estimated on the basis of the half cast factor. The effect of rock strength, rock quality designation, orientation , frequency and aperture of joints, number and thickness of layers and hydrogeological conditions on blast damage has been described.

Jan 1, 2000

By Richard Brummer, John Hadjigeorgiou, Patrick Andrieux

Some of the major challenges associated with underground mining at depth and/or under high extraction ratios are related to the resulting high stress levels, which can lead to the failure and collapse of the rock mass surrounding the excavations. Sudden and violent failures, which can have severe consequences, represent the highest degree of difficulty in terms of underground personnel exposure, erratic and unpredictable production, ground rehabilitation requirements, possible reserve losses and overall mining costs.

Jan 1, 2012

By W. J. Birch, A. Wetherelt

The scaled-distance model for blast vibration analysis is the standard method employed throughout the surface mining and quarrying industries to model Peak Particle Velocity (PPV) data. Although empirical, the method is widely accepted and through the simplicity of its application and ease of graphical verification is set to remain a popular option. The validity of the technique relies principally on the fundamental parametric assumption that blasting data is normally distributed. Throughout the evolution of scaled-distance modelling, this is an issue that has most often been presumed rather than proven (most likely due to the tediousness of the calculations involved). In the few cases when normality has been given some degree of consideration, the result has been the product of a simple visual inspection of frequency distributions: clearly unsatisfactory. However recently the soundness of this assumption has been brought into question, with obvious connotations for blast modelling in general. This paper considers this fundamental issue and seeks to investigate the normality hypothesis within the blasting context through an in-depth statistical analysis of what possibly can be described as an ‘ideal’ blasting dataset. This being a rare case study concerning an opencast coal site in England, where for the entire life of the site every single blast was monitored and recorded through the use of permanent monitoring stations. This has provided a unique ‘total population’ dataset of considerable size from which the assumptions of normality are put to the test.

Jan 1, 2005

By Dale S. Preece, Matthew A. Reisenmay, Avione Northcutt

The ability to simulate the explosive effects of land mines on military vehicles is a valuable capability in the defense community. The current competency levels of such simulations, however, are in need of improvement. Experiments have been conducted to measure the explosive induced impulse of a land mine on a steel plate placed above the explosive charge. The purpose of this paper is to report the findings of a variety of simulation tests conducted in order to correctly predict the empirical impulse data gathered in corresponding experiments. The computer hydrocode, AUTODYN v5.0.01 (Century Dynamics, 2003), is the simulation code used to simulate, and process the results. The experimental data has not been made available to allow computer analysts to exercise their codes on the problem without the temptation to tweak parameters in order to match computer code predictions with experimental results

Jan 1, 2005

By Wenbo Lu

A combined method is present in this paper in analysis the dynamic stability of rock slope under the loading of blast induced seismic, in which, by combining the dynamic load calculating method of quasi-static method with the load inputting method of dynamic finite element method, such factors as the decay of seismic wave along its way of propagation, the frequency. amplitude. the phase difference of seismic wave, etc., can all be taken into account in analysis of the dynamic stability of slope.

Jan 1, 1999

By Jack Eloranta

This paper documents the relationship between material handling and processing coete compared to blasting cost. The old adage, "The cheapest crushing is done in the pit", appears accurate in this c!ase study. Comparison of the accumulated cost of: powder, selected wear materials and electricity; indicate a strong. inverse correlation with powder factor (lbe powder/long ton of rock). In this case, the increased powder cost is more than offset by electrical savings alone.

Jan 1, 1995

By Richard E. Danell

"Blasting is a principal step in the surface mining process for breaking and, in the case of overburdencasting, moving rocks and minerals. As many surface mines are coming to the end of theiroperational life, blasting can once again play an important role through the earthmoving operationsrequired to rehabilitate the minesite. Since blasting is such an energetic and destructive process, itis difficult initially to envisage its use in rehabilitation. However, blasting has found applications inmany civil engineering projects aimed at rehabilitation, including well digging, channelling and soilcompaction. For surface mine rehabilitation, the main purpose of earthmoving operations is toproduce a stable landfonn that will sustain revegetation. In particular, blasting can be applied toreducing the slope of steep walls left by quarrying and open pit mining through a modified form ofthe overburden casting technique. Blasting can also be applied to breaking up pit floors andbenches to speed and improve revegetation of these areas (subsoiling)."

Jan 1, 1994

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Michael D. McGill

The effect of fragmentation size distribution as it relates to front end loader productivity was evaluated by comparing loader cycle times to fragmentation size of the shot rock. At Gold Mine in Southern Utah, a gold deposit containing both limestone and sandstone formations were blasted in the same shot.

Jan 1, 1994

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

"Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape of an organization. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called 'landmarks'), how well they are aligned to support a particular type/nature of innovation in the organization (e.g. radical vs. incremental innovation), and to identify possible gaps between actual and sought performance.The landscape covers four domains that influence innovation - the attributes of the individual, the organizational context in which he/she functions, the business environment (the market / industry in which the organization is operating) and the external environment. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a self-appraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization's particular innovation strategy and environmental context."

Jan 1, 2003

By Robert Hopler

DESCENT INTO A COAL MINE From “The Playbook of Metals, including Personal Narratives of Visits to Coal, Lead, Copper, and Tin Mines,” by John Henry Pepper. Published by Routledge, Wa rne, and Routledge, London, 1862 ENGINEERING NEWS New Yor k January 22, 1903 THE BEGINNING OF THE END OF DYNAMITE. In another part of this issue we have reported the results of some test results made upon one of the safety powders. It will pay every c o n t r a c t o r, miner, or user of explosives in any form to carefully re a d the article re f e r red to. Dynamite has done a gre a t work in the service of man, as did black powder before it; but its i n h e rent dangers are admitted by all and are proved by the long list of deaths and injuries, and destruction to property which annually occur through its use. Why should we continue to use an explosive that annually kills and maims hund reds of men, when others are available which are equally powerful, no more expensive and far less liable to accidental discharg e ? Dynamite when first manufacture d is pure and comparatively safe; but most unfortunately it does not always stay pure; it “rots,” and then it is exceedingly dangerous. More than this, the explosive part of dynamite is a liquid, nitro - g l y c e rine, which is absorbed or soaked up by sawdust, wood pulp or the like. So long as this liquid nitro - glycerine remains pure and remains “soaked up,” or absorbed t h e re is little danger. It has been found, however, that the nitro - g l y cerine leaks under certain conditions. During thawing it fre q u e n t l y leaks out of the stick, or if it becomes wet the water causes the n i t ro-glycerine to leak out. In either case free liquid nitro - g l y c e r i n e escapes, and in that free state it may be exploded by any very slight shock. Nor is this all, if a stick of frozen dynamite be bro k e n a c ross it has been found by tests that the frozen nitro - g l y c e r i n e w h e re thus broken is very sensitive to shocks afterward .

Jan 1, 2004

By Michael S. Wieland

This report focuses on the U.S. Bureau of Mines research regarding desensitization and malfunction of delay detonators and cap-sensitive explosives. Delay blasting in underground coal generates tremendous shock waves and rifting forces that fracture and heave coal. The shock waves from charge explosions radiate outward in all directions through the coal, impacting neighboring charges with later delays. The impact phenomena have debilitating effects, causing degrees of reduced charge performance ranging from misfires or weak detonations to out-of-sequence detonations. Impaired charges react poorly, fracture less coal, and produce fumes with higher toxicity. Coal-mine, underwater, and simulator tests were conducted to more thoroughly understand the shock damage mechanism. Recently the U.S. Bureau of Mines partially resolved the malfunction problem by demonstrating the feasibility of formulating a rugged explosive. This rugged cap-sensitive candidate passed the requisite tests for certifying an underground coal-mine explosive. With natural aging the formulation rapidly lost initiation sensitivity. The charge formulation had to be rebatched to finish the testing and therefore could not be certified.

Jan 1, 1992

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

By Bruce Notthup

Using a Three Dimensional Laser Profiler, persomrel from Austin Powder were able to determine drilling patterns for use in underground mine Room and Pillar blasting operations, The faces had got out of alignment, causing concave faces across the 100 feet wide, 28 feet high tunnels. This was leading to poor drilling and poor blasting results. By profiling the faces, modifications could be made to the drilling pattern to help gradually straighten the faces. The Laser Profiler was also used to check the accuracy of collaring the holes and also perform post blast surveying of the positions of the bootlegs. This allowed recommendations to be made to improve drilling operations at the face. In addition, other volumetric calculations could be performed using the systems’ surveying software, all a lot more easily and quickly than by standard methods.

Jan 1, 1994