Search Documents

By Sandeep Kumar Jeripotula, Govinda Raj Mandela, Aruna Manglapady

The main aim of this work is to evaluate whole-body vibration (WBV) of dozer operators based on three sitting postures (i.e., with 15° lean forward inclination posture, vertically erect posture with no inclination, and with 15° lean backward inclination posture) in Indian surface coal mines. A seat pad tri-axial accelerometer was used to collect WBV data from six dozer operators for three different sitting postures. Results showed that except for Dozer-1, 2, 4, and 5 operators during lean forward sitting posture and Dozer-4 operator during vertical erected posture, no other dozer operators have exceeded an exposure limit value (ELV) of 1.15 m/s2 in any of the considered sitting postures. Similarly, the vibration dose value (VDV) based on exposure action value (EAV) of 9.1 m/s1.75 has surpassed for all the dozers. But no dozer operator has exceeded an exposure limit value of 21 m/s1.75. The outcome of the study infers that based on “above health guidance caution zone (HGCZ)” for daily vibration exposure, i.e., A(8) measurements, for the operator sitting in lean backward postures the vibration amplification was reduced by 32.89% less compared with lean forward posture and 16.23% less when compared with vertically erected posture. Similarly, based on VDV(8), the exposure to vibration for the lean backward posture was reduced by 33.34% when compared with lean forward posture and 17.11% less when compared with vertically erected posture. Based on the above observation, it is concluded that lean back inclination with a trunk flexion of 15° is a favorable sitting posture, as it exposes the dozer operators to minimum vibration.

By Bo Hyun Kim, Mark K. Larson

This study was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to better understand rock-mass behavior in longwall coal mines in highly stressed, bump-prone ground. The floor-heave and nofloor- heave phenomena at a western US coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria (i.e., Mohr–Coulomb or Hoek–Brown failure criterion). The previous numerical study demonstrated these phenomena using a user-defined model of the s-shaped brittle failure criterion in conjunction with a spalling process in the FLAC3D numerical modeling software. The results of the FLAC3D modeling agreed with the observations of the relative amounts of heave from each gate-road system. However, the FLAC3D model adopted many assumptions and simplifications that were not very realistic from a physical or mechanical perspective. To overcome the limitations of the FLAC3D model, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. The effect of stress rotation in the mining-induced stress field was considered by using a different geometry of rock fractures in the coal seam. The heterogeneity of the engineering properties (i.e., cohesion and tensile strength) were also considered by using Monte Carlo simulations. Consequently, the 3DEC models using the DFN technique resulted in predictions of floor heave that agreed with observations of the relative amounts of heave from each gate-road system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Apr 14, 2022

By BO HYUN KIM, MARK K. LARSON

The floor-heave and no-floor-heave phenomena at a western U.S. coal mine could not be properly simulated in numerical models using conventional shear-dominant failure criteria. Although the previous numerical study using FLAC3D very reasonably demonstrated these phenomena, 3DEC modeling in conjunction with the discrete fracture network (DFN) technique was performed to better understand the true behavior of floor heave associated with underground mining in an anisotropic stress field. As a result, the latter models predicted floor heave that agreed with relative amounts of observed heave from each gateroad system, but the cause of heave was mainly related to the degree of anisotropy instead of the size of the pillar.

Sep 1, 2022

By R. E. Utting

INTRODUCTION Until recently, gamma doses had been largely ignored in Ontario uranium mines. This has been due to the assumption that these doses are small and have been more or less unchanged with time and hence their effects have been included automatically in the epidemiological studies that led to the establishment of radon daughter exposure limits. This assumption had to be challenged for two basic reasons. The first was that radon daughter exposures to miners have been progressively reduced over the years due to improved ventilation and ever more stringent regulations, while gamma exposures have presumably remained relatively unchanged. Therefore it must be assumed that the ratio of gamma to radon daughter exposure has gone up. The second reason is more philosophical. It is clearly inappropriate to make judgements on the significance of a potential industrial hazard when the magnitude of that hazard has not been fully assessed. Having decided that some sort of assessment of gamma exposures to uranium miners must be made, it was than necessary to determine how this should be done. Several options were available, for instance: (i) Wholesale personal gamma dosimetry for all mine and mill workers, (ii) Personal gamma dosimetry only for those workers suspected of receiving the higher doses, coupled with area monitoring to estimate the exposures of other workers, (iii) Area monitoring coupled with dose rate times time calculations for all. This would correspond to the generally prevalent method of assessing radon daughter exposures. It was argued that since radon daughter exposures are the major radiological hazard in uranium mines, to invest resources for assessing a lesser hazard to a greater degree of precision was not cost effective. (iv) Since gamma dose rate is related to ore grade, individual doses could be assigned from knowledge of work location and ore grade. Before deciding which of these options would be most appropriate, it was necessary to have some idea of the magnitude of the problem. Very few data were available in the literature and with the exception of a few spot dose rate measurements, and the results of a few gamma dosimeters issued to selected individuals by some of the mining companies, nothing was available. A rule of thumb of obscure origin is often quoted within the industry indicating that gamma dose rates underground will be about 0.25 mR/h per lb/ton or 5 mR/h per % U. This had been used by some to justify neglecting gamma radiation at least for ore grades of the order of 0.1% or 2 lb/ton, on the grounds that gamma dose rates would be of the order of 0.5 mR/h and therefore give rise to annual doses of only about 10 mSv (lrem). That is, it was assumed that gamma radiation was of limited concern compared to the hazard associated with the inhalation of radon daughters. We were thus faced with the situation of just assuming that no regulatory limits were being breached. This situation could not be allowed to continue. A program was initiated to investigate the gamma doses absorbed by uranium miners in three mines in Ontario, and extensive gamma surveys were conducted in the Quirke 2 mine of Rio Algom Ltd, Elliot Lake; Denison Mine, Elliot Lake; and Agnew Lake Mine, Espanola. Negative reaction was received from several mine company officials to the possibility of all miners being required to wear personal gamma dosimeters due to the logistical difficulties involved, and therefore part of the project was aimed at determining if a reliable correlation between gamma dose rate and ore grade in the work location could be deduced, in order that dose rate times time calculations might be used for gamma dose assessments. The results of these programs provided evidence that the gamma dose for some employees in the three mines investigated may be a significant fraction of the current maximum permissible annual dose of 50mSv (5 rem). When combined with radon daughter exposures in the manner recommended by the ICRP at their 1980 Brighton meeting (ICRP 80) the results indicated that some individuals will come close to the resulting limit and may even exceed it. The results also indicate that is probably not feasible to develop a reliable formula for

Jan 1, 1981

By M. A. Ouederni, G. C. Chorosz, E. P. Déliac

This paper deals with the heat flow problems in deep workings (depth greater than 1000 m in France). The approach benefitted from experience gathered in France and South Africa. Deep mines are located in the East of France (coal in Lorraine and potash in Alsace), where the geothermal gradient can reach 4 'C per 100 m (Virgin Rock Temperatures, VRT, around 50 'C). This paper is concerned with the following topics: method of studying the heat flow problem on a mine-wide basis, specific models for heat and moisture pick-up, interfacing of heat and ventilation calculations and a case history in the Lorraine collieries. The heat flow problem on a mine-wide basis is studied in a fashion similar to ventilation networks. Each branch is considered as a "black box" where the air picks up heat and moisture (or is cooled, in the case of an air-cooler). Each box is therefore modeled as a heat transfer unit, hence the calculation of outlet temperatures (wet- and dry-bulb) from the intake ones. The whole network can thus be computed as a sequence of boxes from the air intakes towards the outlets. The second section reviews a number of models used for the assessment of heat and moisture pick-up in the "boxes", with emphasis on stopes and development ends, which are particular to the mining method in use. Two types of stopes are considered: longwall (horizontal and inclined) and cut-and-fill (subvertical). Mechanized rock breaking and blasting can be accounted for. A particular attention is given to development ends, especially complex from the heat flow point of view (rock characteristics, wetness factors, etc.) and usually quite hot. These workings, which are critical in order to secure new production areas, are studied on an average basis as well as in extreme conditions. The calculation takes into account the history of rock temperatures. The interaction between ventilation and thermodynamic calculations is still under development. The idea consists of coupling ventilation calculations with the "box" models: the first step determines the direction of air flow, hence the sequence of the boxes; thereafter the calculations yield the effect of temperature and presssures on air flows. The final section reports on the validation of the whole approach against field data. It concerns several heat flow surveys aimed at checking the models for shafts, stopes and development ends. The accuracy of the method is found very satisfactory.

Jan 1, 1987

By Sahendra Ram, Priyadarshi Onam, Abhishek Kumar Singh

A numerical simulation study is carried out for assessment of stability of coal pillars having dirt bands by varying its size and depths. Physico-mechanical properties of dirt bands including thickness and its position in pillar system are varied in the simulation study. Results of the simulation study are correlated with the available empirical approaches of pillar strength are validated with field observations. It is observed that the presence of weak dirt bands significantly influences the strength of pillar. An attempt is made to develop correction factor for the available empirical approaches, which are developed without considering the weak dirt bands in pillar system. The findings of the study will be helpful for suitable design of different size of coal pillars at different depths and stages of depillaring operations.

Feb 1, 2025

By D. W. McGlashan

[Comideha;tion o 4 chyakd- chem and aLtuctund phopetttiu o auRdide nm&, The in~o/uncction gained h ;to be uned ;to iM;tmph& ( I! dnukey bho hen mind-aundacu , ( 2 ) modidicakio~n 06 ;the minmd n~tdacu, and (3) eac;tiom at ;the mind adac fnom ;thu e baic din oipfina, concep;tc, wLth hegattd ;to .the changen kha;t awtgacu undehgu, heac;tiom kha;t might take place, ,the geom&y 04 ;the inkmduce, ;the nkde 04 diddmenk &om and iom in ;the intmdace, and okhm phyaicd and chemicd pttopemXu od an intmdace mun;t be developed, weighed and appfied. The au/tho~ ded wah thue concep;tud connidmatiom @om which hypokhuu me n& ko denchibe khe envhomenkd-ivttadaciae hela;tiomhipa doh nevmd nddide minettah, The ch&enge and moltivation in khe hu eattch h in a henhe a deattch doh baic dad and helcctiomkipa needed doh accompfi he&.] INTRODUCTION Qualitative and quantitative explanation of particulate solid separations are unknown entities because of the lack of adequate models and mathematical relationships to explain the activity occur- ring between the solid and liquid phases. It is a transitional region in which it is difficult to ascertain the mechanisms of adsorption of ions, molecules, etc. on mineral surfaces, as well as other secondary reactions which occur in interfacial regions. Thus, in this paper the authors deal with conceptual considerations from which hypotheses are set forth to describe the environmental- interfacial relationships for sulfide minerals.

Jan 1, 1968

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By Daniel de la Rosa, Juan Manuel Mayoral, Damián Vital

"This paper presents a numerical study regarding the loads, and the corresponding damage, taken by the primary and secondary lining of a tunnel built in cemented fine-grained stiff soils. This study aims at establishing more rational design criteria that take into account explicity the lining performance. A 3.5 km long tunnel to be built in a densely populated northwest area of Mexico City, was considered as case study. Series of three-dimensional finite difference models, developed with FLAC3D, were used to simulate the tunnel construction, and to compute the ground settlements, internal forces, bending moments, and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams were used to study the lining performance. Several advancement lengths, and tunnel covers were considered to establish their impact on the loads transferred to the tunnel lining. A practice-oriented damage criterion for tunnels was proposed based on the interaction diagram analysis. INTRODUCTION Lining performance during conventional tunnelling, CT, as defined by the International Tunnel Association, ITA (ITA 2009) is strongly affected by the construction procedure. Special attention must be taken in cemented fine-grained materials, such as those found in the northeast portion of Mexico City, due to the potential of fragile failure (i.e. the soil fails suddenly without important deformation) that these soils may exhibit. During CT, it is assumed that the ground strength contributes to the stability of the excavation, as long as the lining is built correctly. It is common practice to consider two structures, which together form the tunnel support: 1) A primary lining, which is a flexible support, which allows excavation walls to deform to mobilize part of its shear strength, and thus contributes to the tunnel self-stability, and 2) A secondary lining. Commonly, the primary lining consists of several layers of shotcrete. In this case the installation method guarantees perfect contact between the lining and the excavation perimeter. The secondary lining, if required, is used to withstand the load conditions in the long term and also has an esthetic function. This paper presents a numerical study aimed at establishing a performance damage criterion for the primary and secondary lining design in cemented fine-grained stiff soils. Due to the lack of data, the strength and deformation parameters were established through empirically-derived relationships. Three-dimensional finite difference models were developed to simulate the tunnel construction, and compute ground settlements, internal forces, bending moments and displacements acting both on the primary and secondary tunnel linings. Interaction diagrams, along with a damage criterion were used to study the lining performance. From the results gathered insight was gained regarding tunnel lining performance during CT."

Jan 1, 2016

By F. Segobia, H. Lozano, M. Portal, F. Ysla, L. Goicochea

This case study evaluates the long- term physical stability of various historical mining structures remediated by the Center for Mining Environmental Research and Studies (CIEMAN) in Hualgayoc, Cajamarca, Peru. The region has a long history of mining activity, with remnants dating back to pre-Inca times. CIEMAN has assumed responsibility for remediating 286 environmental liabilities in the area, including adits, shafts, pits, tailings, and waste rock dumps. The study analyzes the methods employed to stabilize these structures, including geotechnical engineering techniques and revegetation. Long-term monitoring results are presented, assessing the effectiveness of remediation measures and predicting the future stability of the structures. This study highlights the importance of responsible remediation of mining environmental liabilities to ensure the safety and sustainability of communities and ecosystems affected by historical mining.

Feb 1, 2025

By R. D. Begley, A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation has been made, both at the surface and subsurface, at three longwall mines in northern West Virginia. Ground movements were monitored during a three- year period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including graphical (NCB), profile function, influence functions (USBM, Bals', Knothe's, and zone area) will he presented. A brief geologic and topographic description of each site, along with the instrumentation and monitoring program, will also he presented.

Jan 1, 1990

By A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation, both at the surface and subsurface of three longwall mines in northern West Virginia have been made. Ground movements were monitored during" a three year-period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including, graphical {NCB}, profile function, influence functions (USBM, BAL'S, KNOTHE'S, and zone area) will be presented. A brief geologic and topographic description of each site along with the instrumentation and monitoring program will also be presented.

Jan 1, 1989

By E. R. Reeves

The mining industry has recognized the importance of engineering controls as a primary means of preventing hearing loss. The noise control treatments most commonly observed on drills and bolters during this study were windshields, sound absorbing material, and hydraulic motor covers. These controls were evaluated on machines at underground metal mines to determine the amount of noise reduction achieved by each control. The results indicate that absorbing material has very little effect on the noise level. The noise reduction attributable to the motor covers was dependent on the material used to create the cover. Properly installed windshields were the most consistent control.

Jan 1, 2004

By J. A. Organiscak

Data on dust-control practices, mining conditions and occupational exposures were gathered for approximately 80 underground continuous mining units. Despite silica contents on dust samples in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/m3 on a majority of occupational dust samples, while the remainder had difficulty maintaining this level. These two sample sets were termed Group A operations and Group B operations, respectively. This data was compared to identify causes of high occupational silica dust exposures. Analyses of dust-control parameters and geologies revealed only minor differences between these two groups. However, subsequent comparisons of face ventilation design showed considerable differences in silica exposure and silica content between Group A and Group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber. This face ventilation system can benefit operations having difficulty controlling silica dust exposure and silica dust content. The collected data also showed that occupational samples from Group B operations possessed generally higher silica exposures and silica content than similar samples from Group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

Jan 1, 2002

By Jan W. Oberholzer, Jan J. L. Du Plessis, Gerard Appelman, Andrzej M. Wala

The use of on-board scrubbers on continuous miners is an important aspect in efforts to reduce the amount of dust that heading workers are exposed to. As part of the CSIR:Mining Technology's research programme to combat dust, a collaborative project with the University of Pretoria was conducted to evaluate scrubbers. Based on fundamental parameters that were identified to play a role in determining the efficiency of scrubbers, a protocol for testing scrubbers in the laboratory environment, as well as the working section, was established. Tests on various prototype scrubbers were conducted in the laboratory environment. These tests proved some of the fundamental premises according to which scrubbers were designed. By testing some of the newer scrubber types underground, insight into the effect of alternative design aspects on scrubber efficiencies was obtained. The importance of the factors which play a role in reducing the amount of dust in the air is illustrated, as well as the role which other non-design factors play in the reduction of dust levels.

Jan 1, 1995

By E. Bakhtavar

All parameters influencing the decision for selection of a suitable extraction method were first selected as the base of this study. Then these parameters were categorized in two main groups. The first group of the parameters includes ?geomechanical and inherent characteristics of the dimension stones? such as hardness, RQD, compressive strength, joints plane orientation and spacing, and water content. The second group was named ?technical and economical parameters associated with the investor?s objectives? like for example extraction capacity (production rate), blocks recovery, mechanization, capital investment and operational costs. Finally, the influences of all mentioned parameters on the selection of the most applicable extraction methods have been assessed and discussed.

Jan 1, 2012

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By G. Fehr, B. B. Panda, R. Bansberg, K. Arnold, T. Freiman

To evaluate the potential for process solutions to contaminate groundwater outside of the area of the Oxide Pit, it is necessary to predict the ultimate maximum pit lake elevation once pit-related mining activities have ceased. A water balance model was developed based on the existing pit geometry, the groundwater flow equation, and assumed hydrologic input parameters. The model assumed that at any point in time, total inflow into the system (i.e., direct precipitation, surface water and groundwater) minus outflow from the system (evaporation from the lake surface) was equal to the change in the pit water volume. The pit lake depth over time was predicted by assuming a succession of steady- state water balance conditions over short time increments. An analytical method using a spreadsheet and computer model was employed in this study to model the filling of the lake in the Oxide Pit. A sensitivity analysis was performed to evaluate uncertainty associated with the input parameters in the model. The sensitivity analysis indicated that the model was most sensitive to values of precipitation and evaporation and to the static water table.

Jan 1, 2003

By V. Enns, E. Soprovich, J. H. G. Laflamme

A mineralogical and geochemical characterization study was carried out on arsenic-bearing Ketza mine tailings to complement a column extraction test program with the purpose of assessing the potential of arsenic mobilization from the tailings. Two types of tailings samples (i.e., exposed tailings from the impoundment area and water covered tailings samples) were subjected to column tests under standing water cover and with no water cover but weekly flow-through flushing. The tailings have a uniform size distribution. The samples are characterized by high Fe2O3 (44.0 to 68.2 %) and As (3.7 to 4.4w%) concentrations. Ferric hydroxides are the dominant species that are mostly amorphous or cryptocrystalline. Arsenopyrite, scorodite, an Fe-Ca arsenate hydrate phase, an Fe-Bi-As phase and ferric hydroxides are the arsenic-bearing minerals. Arsenic is essentially contained in Ca-As goethite, Fe-Ca arsenate hydrate phase and scorodite. Goethite, although containing low levels of arsenic, could be a significant arsenic-bearing phase because of its high abundance. There does not appear to be any significant chemical or mineralogical difference between the original exposed tailings and the material left underwater with no flow-through for over a year. There are differences in terms of CaO, Fe2O3, SiO,, As, goethite, scorodite, calcite and dolomite concentrations between the exposed tailings and the column material after undergoing approximately two-year flow-through and aggressive leach tests. These differences are likely to be resulting from a combination of different column test conditions and sampling or heterogeneity of the material.

Jan 1, 1998

By Felicia F. Peng, Victor Z. Sun, Syd S. Peng

A probability-based analysis method in conjunction with the finite element structure modeling technique to evaluate an entry system stability is developed. Variability of the rock properties and loading surrounding the entry system is taken into consideration to predict a roof stability by using the probability of failure instead of the common safety factor concept. A dynamic programming is applied to establish a recurrence relationship between the degree of potential roof fall and accumulated roof fall index in an area of interested. A probable distribution of roof fall is assessed by using a developed computer program, RFSTAB. The assessment of the roof falling boundary in the longwall entry system is used as the example to illustrate the procedure and effectiveness of this analysis method

Jan 1, 1996