Search Documents

Jan 1, 1991

By Daryl W. Wurster

The Liberty Bridge in Greenville, South Carolina is a curved, cable-stayed, pedestrian bridge with primary support provided by two towers. The bridge is part of the Falls Park redevelopment. The bridge was originally designed to be supported on drilled piers. Alternately, the bridge was supported on a combination of micropiles and anchor piles because of difficult access and subsurface conditions. The use of micropiles and anchor piles led to improved construction scheduling and reduced costs. Micropiles were used to resist compressive loads. Anchor piles were used to resist tensile forces and to eliminate excessive settlement of pile caps into underlying fill during pre-stressing. This paper describes the site history, bridge construction, site and subsurface conditions encountered, and the decisions that led to support of the bridge using micropiles and anchor piles and foundation construction.

Jan 1, 2006

"Integrity tests refer to a variety of non-destructive tests (NDT) whose purpose is to measure or determine the quality and uniformity, and some- times dimensions, of cast-in-place concrete foundation elements. The tests are primarily aimed at detecting zones of poor quality concrete, voids, bulges, and/or necking.The non destructive integrity testing techniques in this section most generally used for drilled shaft testing are based on one of two physical principles - stress wave propagation or nuclear radiation. All of the stress wave methods involve monitoring a deliberately created vibration, usually of very low amplitude (strains on the order of ??). Some methods rely on direct transmission of the signal, while others rely on processing reflections of the imposed signal.The stress wave methods are inherently sensitive to vibrations from other sources, especially at frequencies that fall within the range of interest for the particular test being applied. Construction activity near the shaft being tested; such as: demolition jack-hammering, pile-driving, casing vibration, excavation and movement of track-vehicles are all known sources of interference that might render test data useless. The actual effect of such vibrations will vary with the type of activity, soil conditions and distance from the testing. The test operator must be able to recognize such interference, and the contractor should be prepared to cooperate with the testing personnel by stopping or moving the source of vibration. If this cannot be done immediately, testing should be postponed until the work in question is finished and the vibration source moved or shut down.NDT methods are not suitable substitutes for routine "topside" construction inspection as described in the Drilled Shaft Inspector’s Manual. However, these NDT methods do allow measurements of the quality of concrete placed in drilled shafts, which cannot be made from "topside" construction inspection. They should be considered supplemental to routine construction inspection as they do provide an additional level of quality control."

Jan 1, 2004

By Pan Shisheng

Amodified load transfer method computing the displacement, axial compression, skin resistance, toe resistance, and other static bearing behaviours of piles, is propoesd in this paper. Through deriving a new concrete computational method with simple integration, many complex factors, such as different soil properties of each layer in layered soil, variation of soil parameters with the changes of the depth, different elastic moduli of piles under different loads, and even different areas in the same pile, can all be easily considered. This method fits in with many types of piles, including friction and point bearing piles, precast and cast-in-situ piles. Observation of static loading test on pile is given, and the computed values from the modified load transfer method are found to agree with practical measured results.

Jan 1, 1991

By Lawrence F. Johnsen

Six case histories are presented in which tall, slender high rises are supported on high capacity minicaissons. The recent development of a high strength rebar cage has resulted in compressive loads of up to 3400 kips on 24 inch diameter minicaissons. Provisions in the pending NYC building code will allow borehole video inspection in lieu of load testing. The ?new? technology results from the marriage of several well established methods: rotary duplex well drilling, high capacity micropiles and high capacity reinforced concrete building columns.

Jan 1, 2007

By Rafael A. Rivera

"Since the dawn of construction, there has been a need for excavations, which sometimes need to occur below the groundwater table. Excavations in themselves are difficult enough, with the myriad of requirements, such as engineered support of excavations, considerations for stability and numerous other concerns. Excavations executed in rural landscapes can be accomplished easily without significant consideration to accessibility, adjacent properties or structures, and construction limits and deformations. However, all of these factors can have an impact on excavation considerations in an urban landscape. When digging below the groundwater table, these conditions, along with concerns associated with groundwater drawdown requirements, discharge limitations, groundwater contamination, property limits, adjacent buildings and subsidence concerns, can lead an experienced dewatering contractor to consider diverse installation methodology and equipment to allow construction to occur below the groundwater table.534 W. 29th St. New York, N.Y.There are many things that must be considered when constructing a new high-rise building within a small property footprint measuring 25 ft (7.6 m) wide by 80 ft (24.4 m) in length. When you take into account that the foundation needs to go several feet below the groundwater table and that there are two existing multistory buildings with shallower foundations on either side of the proposed structure, this task now becomes much more difficult. Consideration of geology, groundwater levels, depths of excavation and shoring for the excavation becomes critical to the success of the project. On a regular basis, dewatering contractors confront similar situations in congested cities where available real estate is limited.To minimize the negative impacts of construction dewatering, it is important to mitigate the potential effects of construction dewatering to the surrounding buildings, sidewalks, underground structures, tunnels, subways and other existing infrastructure. Such an instance occurred at the project located at 534 W. 29 St. in New York City. On this particular project, the required drawdown was greater than the typical 15 ft (4.6 m) of suction lift, so a vacuumed can pump system was utilized. The tubing was connected to a vacuumed perimeter dewatering well-point system, which is a predrainage system that is installed prior to the start of excavation for the underpinning of the adjacent structures and for the overall foundation. Each well-point, which was composed of a PVC pipe that was 1.5 in (38 mm) in diameter by 25 ft (7.6 m) long, was drilled to a depth of about 23 ft (7 m) using a hollow stem auger and was installed around the perimeter at a centerto- center spacing of about 7.67 ft (2.3 m). In lieu of a traditional perimeter collection header, and to allow for greater flexibility for the contractor, the well-points were interconnected to a modified vacuum can pump system utilizing ¾ in (19 mm) drop tubes that were “spaghetti” around the perimeter."

Jan 1, 2017

By Roberto A. Lopez, Eric Lindquist, Jon Bussiere, Dean Iwasa

"The new 11-story U.S. Federal Courthouse building in downtown Los Angeles demanded a cost effective foundation system capable of attaining a strict total settlement criterion of 0.5 inches (12 mm) under high applied loads. A design-build ground improvement system consisting of 3 ft (0.9 m) and 7 ft (2.1 m) diameter deep soil mix (DSM) columns embedded into the relatively soft Fernando Formation bedrock was selected for the project. The DSM columns support applied stresses of up to 8,800 psf from four large concrete core elements that transfer concentrated building loads to a 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat. The soil mixing ground improvement solution provided flexibility by allowing installation of the DSM columns around existing belled caissons left in place from prior structures, and by allowing repositioning of some of the DSM columns to avoid other existing obstructions in the fill. DSM spoils were used to construct a 2 ft (0.6 m) thick load transfer platform on top of the DSM columns. Quality control measures included utilizing equipment outfitted with automated data acquisition systems, performing three full scale load tests, performing daily wet-mix sampling and compression testing, performing full-depth coring and unconfined compression testing on core samples, and using a borehole acoustic televiewer to evaluate the uniformity of the DSM columns where core recovery was problematic. The results of subsurface investigation and the load tests were used to develop 3-dimensional finite differences models for evaluating stress distribution and deformation of the foundation system.INTRODUCTIONThe new U.S. Federal Courthouse building is currently under construction in downtown Los Angeles, California. The new courthouse will be 11 stories tall with one partial below-grade B1 basement level. The building will have four structural core elements that extend from the main building foundation at the B1 level to the top of the structure. The majority of the building loads will be transferred through the structural core elements to a new 3 to 6 ft (0.9 to 1.8 m) thick reinforced concrete mat beneath the central portion of the structure. The foundation pressures beneath each of the core element locations will be approximately 6,200 to 8,800 psf (300 to 420 kPa) with lower foundation pressures at locations farther away from the central core area."

Jan 1, 2015

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By M. Mets

Pile foundations have been used in Estonia since the beginning of 1960's. To evaluate the capacity of piles nearly 2,500 pile tests and 1,800 pile loading tests Have been carried out. The pile foundations of nearly 150 houses are under settlement observations.

Jan 1, 2000

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By Mark R. Svinkin

Construction vibrations may adversely affect surrounding buildings and their effects range from human discomfort and disturbance of sensitive devices to visible structural damage. There is no unique conclusion regarding the effect of construction vibrations at every site. Measurement is usually made to monitor vibrations and control them with the vibration thresholds for disturbance of sensitive objects as well as damage to structures. To prevent potential litigation and mitigate the vibration effects on sensitive devices, people and structures, it is necessary to manage and minimize vibration problems before the beginning of construction activities or installation of vibrating machine foundations, and during construction. Pre-construction damage survey and engineering vibration investigations, including the prediction of anticipating vibrations, have to be made at most construction sites in advance of construction activities. Vibration monitoring and control have to be provided during construction. The instrumentation feedback of vibration prediction, monitoring and control provide the basis for choice of measures to prevent or mitigate vibration problems and settlement damage hazards.

Jan 1, 2002

By James M. Tantalla, Roderic A. Ellman, W. Allen Marr, Scott R. Bamford

"Construction of the powerhouse for the Willow Island Hydroelectric Project required a 100-ft deep excavation inside the limits of a cofferdam and embankment-seepage cut-off wall through soil and rock adjacent to the Ohio River. Portions of the rock had preexisting weak plans and slickensided surfaces with low frictional strength. Stability analyses were performed for critical sections of the excavation to evaluate the stability of the soil slopes and rock cuts using buckling, tension crack, and limit equilibrium analysis techniques. Loading conditions included the 100-yr and intermediate floods, normal pool, sudden drawdown, and seismic design conditions.Stability analyses indicated adequate factors of safety for soil slopes and for rock cuts through the landside embankment sections. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated unacceptable factors of safety. Consequently, the riverside portion of the excavation required measures to increase stability. Long, high-capacity rock anchors and deep dewatering wells to lower the site piezometric head were chosen for this purpose.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. Required rock anchor loads varied from 1,968 to 2,074 kips. The designed anchors consisted of multiple, seven–wire strands with up to 59 strands per anchor. Bond lengths used an allowable bond stress of 100 psi based on the rock bond measured with pull-out tests. Maximum bond and anchor lengths were 50 ft and 140 ft, respectively. Measurements of forces in selected strands and displacements of the excavation showed excellent performance."

Jan 1, 2017

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By M. England

Keywords: Bi-directional tests, Osterberg cell, O-cell®, static load tests, Timeset® Static load testing, where loads are applied vertically to the top of the pile and often referred to as &apos;top down testing&apos;, has been used for many years and has become a &apos;standard&apos; test for the world of foundation engineering. The method, although well developed, cannot be used under certain circumstances, magnitude of load being a particular issue. There is a finite limit to the load capacity that can be applied with either kentledge, the use of reaction piles or anchors, and as the loads increase, the costs escalate dramatically. A novel test method seeks to overcome all the associated problems of large scale and restrictive area "top down testing", utilising static load testing techniques. The method requires the foundation element to be divided into two or more sections and these can be loaded axially as required using a portion of the foundation element as a reaction. This paper presents some recent applications and developments in the use and application of the bi-directional testing technique using the Osterberg Cell or O-cell® and outlines some of the many advantages of the system. Recent bi-directional test loads applied to bored piles have mobilised capacities of 279 MN and with flight auger piles up to 25 MN.

Jan 1, 2006

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By Andrea Gambi, Giancarlo Olivucci, Maurizio Lenzi

"In the paper a criterion for the evaluation of the sharing of the lateral loads in a piled foundation is presented. It relies on the the compatibility condition between the rotation of the rigid pile cap and the rotations of the pile heads, following in that the criterion suggested by the Eurocode 8 - Part 5. This assumption leads to an analytical solutions which allows to deal with the sharing of the lateral loads and moments by means of two main interaction parameters only. A sharing domain is also derived and it shows the role played by the eccentricity of the lateral load on the values of the axial forces and of the bending moments at the head of the piles.INTRODUCTIONIt is well known that the interaction among soil, piles and foundation is one of the most complex subject to deal with in Geotechnical Engineering. Its rigorous study needs to employ suitable finite element software nowadays available and able to take into account the non linear behavior of the soil as a continuum and the inelastic response of the structure. A deep insight to the topic of the sharing of the loads cannot obviously renounce to this approach.On the other hand it is a daily need of the designers to have at their disposal simple tools that allow to make preliminary evaluations of the basic equilibrium conditions. To this purpose many methods of analysis have been developed in the past to face the sharing of the loads in a simplified version. The present contribution follows this way trying however to introduce some improvements that leads to find a solution that satisfies both the equilibrium of the forces and the compatibility of the movements (Lenzi, Gambi, Olivucci, 2002). The proposed model allows to identify the basic parameters which govern the sharing of the lateral load and it allows to perform also parametric analysis and quick checks that may be useful in the design of the piles."

Jan 1, 2005

By Jamie D. McEwan

To cater for the future introduction of 12 car trains, London Blackfriars railway station is being extended from the north end to span across the River Thames. Following the demolition of existing buildings, a number of challenges had to be overcome including working adjacent to a live railway line, above live London Underground tracks and working in small restricted spaces. Trains entering and exiting two lines of track at the bridge&apos;s north end of track meant that access was difficult due to the location and proximity to existing infrastructure. The site was very much constrained and congested and there were also a series of works in place to maintain passenger flows so as not to inconvenience the travelling public. The site had been developed many times in the past resulting in a number of obstructions that would require removal during the piling work including old brickwork, reinforced concrete, redundant railway sleepers and track and existing concrete and timber piles. A number of solutions had to be devised to overcome these obstructions. Piling works were undertaken during the day and at night to meet programme.

Jan 1, 2011

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By J. L. Liu

Long-term maintained load test on the bored pile group in unsaturated silty soil has been carried out. And the research on the time effects of bearing behavior of pile group has been done by the method of installing pressure cells and reinforcement stress gauges for measuring the soil reaction beneath the cap and the pile bottom as well as the shaft resistance. The test shows that, within a certain duration after loading, the soil reaction beneath the cap and the pile point resistance increase with time; but the shaft resistance decreases. The load distribution among the pile tops in the group tends to be even with time. The shaft resistance redistributes along the pile shaft with time, that is, getting less in the upper part, getting larger in the middle. The redistribution does not tend to stop till the distribution in both upper and middle part becomes to be uniform. The load-bearing conditions of soil beneath the cap of pile group and the variation in time effects with related factors also have been discussed.

Jan 1, 2010