Search Documents

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By W. A. Wood, W. H. Reimann

A study is made of the creep that can be induced in armco iron at room temperature by superposing small amplitudes of alternating torsion on a tensile creep load. It is shown that the creep differs from that in comparable tests on copper in being trmsient only. At the same time, though transient, the creep can produce extensions of some 10 pct under creep loads less than the tensile yield stress of the material. The creep can be largely suppressed b$ applying cyclic strain of suitable amplitude before applying the creep load and the metal thereby stabilized. At room temperature, plastic flow in a metal under steady load is normally limited by strain-hardening processes. However, if a small cyclic stress is superposed on the steady load these processes may be more or less neutralized and, as shown in recent investigations,'-4 plastic flow may continue. In this way annealed copper, for example, can be induced to creep continuously to fracture under loads as small as 1 tsi. Dislocation mechanisms possibly responsible for this room-temperature creep have been usefully reviewed by Feltner.But discussion so far has been based mainly on creep as it is found in close-packed metals initially in the annealed state, and their behavior may not be general. In fact, recent work shows that the form of creep in annealed copper is different from that even in cold-worked copper;7 the creep thus depends on the dislocation pattern already in a metal as well as on the metal itself. This paper describes the creep in annealed armco iron, tested in the same way as the above-mentioned copper. One object was to see how creep in a typical bcc metal compared with that in the annealed close-packed metals. Another object was to utilize the fact that a bcc metal like iron has a more pronounced elastic range than close-packed metals like copper and to find to what extent the creep load or superposed cyclic stress had to exceed their re-

Jan 1, 1964

By E. G. Loesche

Grinding mills in which the comminution takes place between rollers and the surface of a disc, table or ring are generally known as roller type mills. The Loesche Mill, also known as the Disc Roll Mill, is a special type of roller mill in which the grinding surfaces consist of two rollers assembled over a horizontal disc or table which rotates at a relatively low speed. This design is particularly applicable to industry's present day demand for large capacity grinding mills.

Jan 1, 1964

By K. C. Mills, E. T. Turkdogan

A number of investigators1 6 have noted the presence of a liquid miscibility gap in the Fe-Sn binary system. However, the first attempt to measure the

Jan 1, 1964

By H. L. Luo, P. Duwez, C. C. Chao

BY rapidly cooling alloys from the liquid state, it is possible to obtain solid solutions beyond the equilibrium concentrations, provided that the components are miscible in the liquid state. Typical such cases include CU-Ag,1 Pt-Ag,2 CU-Rh,3 nickel-base alloys with silicon, germanium, and tin,4 and cobalt-base alloys with silicon, germanium, tin, aluminum, and gallium.5 In the present note it is shown that terminal solid solutions can be appreciably extended in A1-Mg alloys. The alloys whose compositions are given in Table I were prepared by induction melting in tantalum crucibles under an argon atmosphere. Both aluminum and magnesium were 99.99 pct pure. Weight losses after melting were less than 0.2 pct for the aluminum-rich alloys and less than 0.4 pct for the magnesium-rich alloys. From these weight losses it was estimated that the compositions of the ingots after melting were accurate within 0.3 at. pct for aluminum-rich alloys and within 0.5 at. pct for magnesium-rich alloys. As indicated in Table I, the compound AuCd10 in which there is an ionic contribution to the bonding. The authors thank Dr. J. H. Westbrook of the Research Laboratory, General Electric Co., for arranging the supply of materials and for his interest. This investigation was supported by the U.S. Atomic Energy Commission under Contract AT(30-1)-1002, Scope I. some of the alloys were also chemically analyzed and the results confirmed the limits of uncertainty based on weight losses. Rapid quenching from the liquid state was achieved by techniques previously described.8,7 The principle of these techniques consists of propelling a small globule of liquid alloy (about 20 mg) onto a copper substrate. The thin foils easily detached from the copper substrate were analyzed by X-ray diffraction using a Debye-Scherrer camera 114.6 mm in diameter and either nickel-filtered copper Ka or iron-filtered cobalt Ka radiation. Since the back-reflection doublets were resolved, the wavelengths used in the computatioas were CuKal = 1.54050A and CoKa1= 1.78892A. Lattice parameters were obtained by extrapolation of the Nelson-Riley function, and the tables compiled

Jan 1, 1964

By A. F. Witt, A. M. Gaudin, A. K. Biswas

Finite contact angles in the rutile-water-organic liquid system are traceable to contamination or are due to addition of a surface-active agent. Finite contact angles are invariably accompanied by hysteresis.1-7 Besides surfactant concentration and pH, the nature of the organic liquid is found to be a factor influencing the magnitude of contact angle hysteresis. In a recent paper the authors have reviewed principles and applications of measurement methods for contact angles and their hysteresis.22 In this paper, these methods are applied to a system consisting of rutile, an organic liquid (benzene, decane, or dode-cane) and water. Surfactant (dodecylamine hydro-chloride) was used at various concentrations and various pH values. MATERIALS A synthetic rutile crystal supplied by the Linde Co. was used. It is a cylinder 1/2 in. diam, with faces cut perpendicular to the c-axis. The crystal is stated to be alumina-free and to be 99.9% pure. Rutile is a high surface energy solid, its calculated average field strength being 2.7 x 105 e.s.u.,9 its dielectric constant10 is 114. The zero point of charge of rutile was measured11 and found to be at pH 6.0. The atomic distances and bond angles of the tetragonal crystal of rutile have been precisely determined.l2 The organic liquids were specially purified. Reagent grade benzene was repeatedly shaken with concentrated sulfuric acid to remove thiophene, then neutralized with sodium hydroxide solution, rinsed with distilled water, dried overnight over anhydrous calcium chloride and filtered. The refractive index of this chemically purified benzene was 1.4977 (at 25°C) - very close to that of pure benzene (n25 1.4979).13 Both n-decane and n-dodecane were washed with aqueous sodium hydroxide, concentrated sulfuric acid (repeatedly, until the acid layer was colorless) and again with alkali, to free the organic hydrocarbon from fatty acids and unsaturated hydrocarbons. The organic phases were subsequently washed with distilled water and dried over anhydrous sodium sulfate. The filtered hydrocarbons were then distilled under vacuum (9-10 mm pressure). Decane, thus purified, showed traces of unsaturated and of carboxylic compounds. On gas chromatographic analysis the purified n-dodecane showed the presence of two impurities. However, the relative retention times of these components did not change substantially when measured on a polar or a nonpolar column. This indicates that the compounds were probably in the same polarity class, i.e. the components were nonpolar like dodecane. Conductivity water has always been one of the liquids. Conductivity of the water used was 10-6 ohm-' cm". Dodecyl ammonium chloride was prepared from pure amine (supplied by Armour and Co., Chicago), by Li in the MIT Mineral Engineering Laboratory.14 The critical micelle concentration at 25°C is known, 0.0138 mol per liter15 or 3.06 gpl. All our experiments have been done at concentrations lower than the critical micelle concentration. The glass vessels, glass drop holder and the rutile crystal were all cleaned with hot chromic acid followed by distilled water, concentrated hydrochloric acid, and again distilled water, and conductivity water. During the experiments, a nitrogen atmosphere was maintained. For this purpose, commercially purified nitrogen was further purified by passing it over hot copper wire at 450°C, then through columns of acidic chromous chloride solution, concentrated alkali solution and distilled water. APPARATUS AND METHODS Hysteresis was produced by the "captive drop" or constant volume drop method as well as by the "expanding-contracting drop" or variable volume drop method. The image of the drop while it is expanding, contracting or moving is projected on a screen and photographed. The developed film is projected through an enlarger and the contact angles measured with a protractor.

Jan 1, 1964

By W. J. Uren, Charles R. Kuzell

The industries engaged in winning minerals from the earth, because of their widespread dissemination, are faced with perhaps as wide a variety of labor-management problems as may be found in any other broad sphere of productive activity. Those problems are continually increasing in volume and complexity, and management has become aware of their growing importance. For the past quarter century at least, labor-management problems have largely been union-management problems. During this period tremendous assistance has been given labor unions through legislation and administrative and political action. In the United States, legislation favorable to unions has come about in the form of the now defunct National Industrial Recovery Act; the Wagner Act, most of which has been carried forward in the Taft-Hartley Act and the Landrum-Griffin Act; the Norris-La Guardia Act, the Wage and Hour Law, the Walsh-Healey Act, and others. The result has been to transfer from the hands of management to those who direct the affairs of the unions a large share of control over the industry and to hamper in many ways the remaining control left to management. In the United States there are many examples of the power of unions to injure whole industries seriously without regard to the interests of management, the employes, or the public. During 1958 and 1959 revelations of corruption and coercion in labor unions made before the McClellan Committee of the U. S. Senate generated considerable public sentiment in favor of legislation to protect the interests of employes and the public. However, the resulting legislation, the Labor-Management Reporting and Disclosure Act of 1959 (Landrum-Griffin Act), demonstrated quite clearly that the political power of the labor union leaders was adequate to prevent adoption of effective measures in this field.

Jan 1, 1964

By W. A. Backofen, G. Y. Chin, W. F. Hosford

The effect of machine stiffness on discontinuous flow and fracture of the 2024 aluminum alloy was studied in tension at 4.2OK. An increase of machine stiffness was found to decrease the amount of elongation and drop in load during discontinuous flow, thereby postponing fracture to larger strains and higher stresses. The possibility of utilizing stiffened tools in deformation processing to suppress shear fracture originating from unstable flow was indicated. The problem of nucleating discontinuous flow and the role of the effective mass of the system in discontinuous flow were also considered. AT low temperatures the plastic flow of metals is often discontinuous, with sudden load drops and elongations.1,3 Basinski1,4 has presented strong evidence that discontinuous flow, at least in aluminum alloys, occurs under nearly adiabatic conditions. During testing the load may drop suddenly and flow become localized when the thermal softening, due to heat generated in plastic straining, is greater than the strain and strain-rate hardening. This instability criterion is more easily satisfied at low temperatures because 1) the volume specific heat is reduced so that relatively large temperature increases are possible in straining, and 2) the flow stress is relatively temperature-dependent. The important role of adiabatic shear in ductile fracture processes has been emphasized,5-1 and consideration has already been given to the influences of thermal and mechanical properties on the tendency of a material to undergo adiabatic shear.17677 By focusing attention on how the mechanical loading system influences low-temperature discontinuous flow, additional insight into adiabatic shear and its effect on fracture may be gained. EXPERIMENTAL PROCEDURE Because of its low thermal conductivity, the 2024 aluminum alloy exhibits a highly consistent discon- tinuous-flow behavior at 4.2°K and was therefore chosen as the material for study. Machined specimens of 0.113 in. diam and 1.125 in. gage length were solution heat-treated at 490°C for 3 hr, quenched into cold water, and immediately immersed in liquid nitrogen until just before testing. Testing was done at 4.2°K by immersion in liquid helium at a crosshead drive rate of 0.03 in. per min. As normally used (hard-machine basis), the spring constant of the testing machine was k = 25,000 lb per in. By inserting beam springs in series with the specimen, this value could be lowered by a factor of about 100. Details can be found elsewhere.? As a result of variable machine stiffness, the actual strain rate ranged from about 3 x 10 5 to 3 x 10-4 per sec from one test to another, as well as within any one test. However, preliminary tests had established that the tensile curves were not altered significantly by this strain-rate variation. Fig. 1 shows a typical load vs plastic-elongation curve for a solution heat-treated 2024 aluminum alloy specimen pulled in the standard hard machine (k = 25,000 lb per in.) at 4.2"K. The elastic extension has been subtracted. Plastic flow proceeded smoothly from yielding at approximately 22,000 psi (load = 220 lb) to a strain of about 4 pct at which point the flow became discontinuous. The magnitude of the load drops as well as the plastic elongation per drop increased with increasing strain until the specimen finally broke abruptly. The load-elongation behavior of a sample tested with a relatively soft machine under otherwise identical conditions is given in Fig. 2. In general, there

Jan 1, 1964

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By G. L. Smit

The Buffelsfontein Gold Mining Company is situated in the Klerksdorp district of the Province of the Transvaal in the Republic of South Africa, approximately 100 miles west of Johannesburg. Gold production commenced in January 1957 and Uranium treatment of residue slimes as a by-product started in July 1957. The mining property is 5435 mining claims in extent, the equivalent of 7988 acres or 12.5 sq miles. The mine was initially exploited by the Pioneer Twin Shaft System, consisting of a 26-ft diam down-cast shaft and a 22 ft-diam up-cast shaft, sunk in the north-west area of the mine to cater for the hoisting and ventilation requirements for a milling rate of 150,000 tons per month. To exploit the Eastern zone of the property and assist in increasing production to 200,000 tons milled per month, it was decided to sink a further Twin Shaft System consisting of a 28-ft diam downcast shaft and a ventilation up-cast shaft -22-ft in diam, both monolithic concrete lined — 200 ft apart and 5300 ft deep. This paper deals with the sinking and commissioning of these Eastern Twin Shafts. This was achieved by one sinking crew within a period of 20 months. A) PLANNING 1) Siting: The Eastern Shaft System was sited in the north-east area of the property, 12,000 ft east on strike from the Pioneer System. (Fig. 1). Initially the system was sunk to the 5300 ft elevation to conform with the original Pioneer Shaft System. On completion a sub-vertical main shaft will be sunk to the 8000 ft elevation in the immediate vicinity, and subsequently the surface ventilation shaft will be deepened to this elevation by raising from level to level and sliping to full size. The exact positions of the shafts were chosen after: a) underground development had located certain known water bearing zones, and b) geophysical and topographical surveys had been carried out. The shafts passed through the following geological succession: Surface to 4430 ft - Dolomites of the Transvaal System 4430 to 4470 ft - Quartzites and conglomerates of the Black Reef Series of the Transvaal System. 4470 to 4470 ft - Diabasic Lava of the Venters-dorp System (Ventersdorp Contact Reef at base). 4470 to 5250 ft - Quartzites of the Elsburg Series of the Upper Witwaters-rand System. The shafts were sited to ensure that the least possible water would be encountered during sinking, and this contributed to the rapid rate of sinking. 2) Duties: a) The 22-ft diam ventilation shaft was designed to up-cast 1,400,000 cfm of air (0.060 density) against a resistance of 22 in. water gauge. b) The main shaft was designed to handle 160,000 tons hoisted per month as well as the men, material and down-cast ventilation to serve this tonnage. The 284 diam main shaft is equipped with streamlined buntons spaced at 15 ft centers set in pockets which were left during sinking. There are six compartments, four of which are sewed by two dual purpose hoists, hoisting either, twedeck man cages or 13-ton bottom discharge skips. The other two compartments are served by a single purpose winder hoisting double deck cages accommodating 60 men per deck. (Fig. 2). 3) Timing: Permanent equipment was ordered well in advance to insure continuity in the operation. Development underground reached the shaft positions before the start of sinking operations. From this development, boreholes were drilled into shaft positions to drain off water in the vicinity of the shafts. To ensure complete co-ordination of effort, all relevant data, as well as the allocation of responsibility, were made known to all persons and departments concerned. 4) Models: The extensive use of scale models during the preliminary planning stages proved most useful in deciding on design such as buntons, bunton pockets and guide cleats, and complex layouts concerning loading, spillage and pumping arrangements. (Fig. 3). These models also proved invaluable in determining the walling routine. Normal working conditions could

Jan 1, 1964

By W. A. Wood, W. H. Reimann, K. R. Sargant

A study is made of the microstructural changes produced in armco and pure iron subjected to alternating torsion at amplitudes above and below the knee of the S/N curve. The aim was to identify the basic mechanisms of fatigue and to find why they should give rise to a sharp S/N knee in contrast to the type of S/N curve shown by fcc metals. It is found that the basic structural change above the knee in the iron is a pronounced cell formation in the grains, which determines irregular micro-cracks, and below the knee a dispersion of fine slip that determines a dispersed pore formation in the grains. Comparison of these changes with those in fcc metals similarly tested shows that they do not include an intermediate structural change, a concentrating of slip in narrow bands with associated slip-band cracking, that characterizes the fcc metals and accounts for their different type of S/N curve. RECENT conferences on basic mechanisms of fatigue emphasize that fatigue damage takes many forms: for example, cracking in slip bands (Thompson1), at grain boundaries and inclusions (Hempel'), at precipitation zones in alloys (Han-stock, Forsythe), or at surface notch-peak effects, both hypothetical (Mott, cottrel16) and observed (Wood). Evidently it is not easy to see in this diversity a basic mechanism. At the same time the contributions suggest that some reconciliation may be possible if distinctions are drawn between three phases of the fatigue process: initiation of damage at nuclei, distribution of these nuclei, and the final macroscopic crack system. In initiation, the relevant features appear to be that nuclei may appear early, at least by 1/100th to 1/1000th of the life of a test specimen; that they may do so at many independent centers, appearing according to some observationsa as pores or voids; and that they are not necessarily self-propagating, damage spreading rather by their multiplication. In distribution, the relevant feature appears to be that they form preferentially in zones where the microstructure becomes abnormally strained (as defined more closely below). Now in these two phases the basic fatigue process should be systematic. But, at the same time, the "abnormal strains" in particular set the stage for considerable diversity in the final phase of macroscopic cracking, for where zones of abnormal strain develop will depend on what kind of fatigue deformation is applied and what kind of prior processing the test material has had. On this view it seems desirable to know what in

Jan 1, 1964

By Burton H. Boyum

The paper generally reviews the iron ore occurrences and regional geology of Western Australia, but features in particular the mesa deposits of PJasic Materials - Cliffs International. Initial production is planned from a aeries of mesa deposits of Eocene-Oligocene age. The ore is oölitic to pisolitic goethite and hematite. Source of the iron in the mesa deposits is thought to be from the Precambrian iron-formations. The geology and occurrences of the mesa iron ore deposits are summarized and illustrated.

Jan 1, 1964

The Sixtieth Regular Meeting of the Rocky Mountain Coal Mining Institute convening at the Stanley Hotel in Estes Park, Colorado, was declared in session at 10:10 a.m. by Past President Mike Zakotnik, Jr., General Superintendent, The Kemmerer Coal Company, Frontier, Wyoming. Mike introduced Claude P. Heiner, President, Minerals and Development Corporation, Salt Lake City, Utah; and President of the Rocky Mountain Coal Mining Institute. President's Address Members of the Rocky Mountain Coal Min- ing Institute, guests, visitors and friends: I feel this is a distinct honor to talk to you on the occasion of this 60th regular meeting of the Institute. I once assumed this would be the Institute's 60th birthday, but later found that the first meeting was held in the State Capitol at Denver on November 12, 1912, at which time a comparatively small group of operators duly organized the Institute; a Mr. Weitzel of Colorado Fuel & Iron Company was then elected president and our late and dearly remembered Fred W. Whiteside, whose wife Gussie now carries Fred's work forward, was elected secretary. From Fred's records, early meetings were held semi-annually at rather irregular intervals, so that this 60th meeting is approximately the 52nd birthday of the organization and I am number 44 to serve as president. This latter development, I am sure, was conjured up last year by certain members at Glenwood Springs when I was absent. Anyway, I am honored and trust 'that these sessions will be both interesting and instructive in helping us on our way in the coal business.

Jan 1, 1964

By R H. Hallam

The Mattagami mining district encompasses a favour-?able belt of folded Keewatin-type rocks, with intercalated sediments and intrusives of late Keewatin age. This environment has been subjected to periods of basic and acidic intrusion. The orebodies lie within the fold structure and are associated with faulting and shearing of considerable magnitude. The No. 1 orebody contains 60 to 70 per cent massive sulphides. The minerals, in their order of abundance, are generally: pyrite, sphalerite, pyrrhotite, magnetite and chalcopyrite. It is evident that the broad geological structure of the district is amenable to ore deposition. There are two ? prominent linear expressions which comprise this broad structure. Both strike directions lie at the edge of, or are related to, a complex gabbro-anorthosite-peridotite zone. The fact that eleven of the ore zones discovered to date coincide with the broad structure indicates its over-all importance. It is estimated that the production from Mattagami Lake Mines will be in the range of 600 to 700 tons of zinc concentrate and 70 tons of copper concentrate per day.

Jan 1, 1964

By C. F. Austin, J. K. Pringle

In view of the many large differences in structure and physical properties between metals, plastics, and most rock materials, a continuing experimental petrodynamics program has been established at the U. S. Naval Ordnance Test Station. Part of this program has been to test the concepts of scabbing and corner fracturing in a typical coarse-grained rock. The results of this experimental program have shown very interesting differences between the formation of fractures in rock and the formation of fractures in other materials such as metals and plastics which are often used as models for rock behavior studies. The gross behavior of coarse-grained brittle solids subjected to impulsive loading has undergone abundant empirical investigation by mining organizations and by mineral research agencies. However, the fundamental response of coarse-grained brittle solids to impulsive loading has received little detailed study in recent years. The various organizations and agencies interested in rock-like brittle materials have broadly applied the stress wave interaction concepts of the impulsive failure of metallic samples to the behavior of granular brittle materials 1,2,3,4,5,6 Using the metallic sample approach for stress wave induced fracturing, an understanding of the fracture behavior of brittle materials which perhaps is not always appropriate has been established in the open literature. An excellent summary of the metallic sample approach is provided by ref. 7 which summarizes the general beliefs prevalent at present regarding the impulsive behavior of brittle solids: "In the blasting process, rock breakage occurs primarily from tensile slabbing, beginning at a free face and proceeding back toward the explosive charge. The tensile waves formed by the reflection of incident compressive waves from two or more free faces will collide in the rock, resulting in large localized tensile stresses. Fractures formed by the interaction of these tensile stresses begin at the apex of the free face planes and progress back into the rock as shown...."

Jan 1, 1964

By Takashi Katsura, Avnulf Muan

Equilibrium relations in the system FeO-Fe2O3 Cr2O3 have been determined at 1300°C at oxygen pressures ranging from that of air (0.21 atm) to 1.5 x 10-11 atm. The following oxide phases have stable equilibrium existence under these conditions : a sesquioxide solid solution with corundum-type structure (approximate composition Fe2O3-Cr2O3); a ternary solid solution with spinel-type structure (approximate composition FeO Fe2O3-FeO Cr2O3) and a ternary wüstite solid solution with periclase-type structure and compositions approaching FeO. The metal phase occurring in equilibrium with oxide phase(s) at the lowest oxygen pressures used in the present investigation is almost pure iron. The extent of solid-solution areas and the location of oxygen isobars have been determined. ThE system Fe-Cr-O has attracted a great deal of interest among metallurgists as well as ceramists and geochemists. Metallurgists have studied the system because of its importance in deoxidation equilibria, ceramists because of its importance in basic brick technology, and geochemists because of its importance for an understanding of natural chromite deposits. Chen and chipman1 investigated the Cr-O equilibrium in liquid iron at 1595°C in atmospheres of known oxygen pressures (controlled H2O/H2 ratios). The main purpose of their work was to determine the stability range of the iron-chromite phase. Hilty et al.2 studied oxide phases in equilibrium with liquid Fe-Cr alloys at 1550°, 1600°, and 1650°C. They reported the existence of two previously unknown oxide phases, one a distorted spinel with composition intermediate between FeO Cr203 and Cr3O4, the other Cr3O4 with tetragonal structure. They also sketched diagrams showing the inferred liqui-dus surface and the inferred 1600°C isothermal section for the system Fe-Cr-O. Koch et al3 studied oxide inclusions in Fe-Cr alloys and also observed the distorted spinel phase reported by Hilty et al. Richards and white4 as well as Woodhouse and White5 investigated spinel-sesquioxide equilibria in the system Fe-Cr-O in air in the temperature range of 1420" to 1650°C, and Muan and Somiya6 delineated approximate phase relations in the system in air from 1400" to 2050°C. The present study was carried out at a constant temperature of 1300° C and at oxygen pressures ranging from 0.21 atm (air) to 1.5 x 10-11 atm. The chosen temperature is high enough to permit equilibrium to be attained within a reasonable period of time within most composition areas of the system, and still low enough to permit use of experimental methods which give highly accurate and reliable results. These methods are described in detail in the following. I) EXPERIMENTAL METHODS 1) General Procedures. Two different experimental methods were used in the present investigation: quenching and thermogravimetry. In the quenching method, oxide samples were heated at chosen temperature and chosen oxygen pressure until equilibrium was attained among gas and condensed phases. The samples were then quenched rapidly to room temperature and the phases present determined by X-ray and microscopic examination. Total compositions were determined by chemical analysis after quenching. In the thermogravimetric method, pellets of oxide mixtures were suspended by a thin platinum wire from one beam of an analytical balance, and the weight changes were recorded as a function of oxygen pressure at constant temperature. The data thus obtained were used to locate oxygen isobars. The courses of the latter curves reflect changes in phase assemblages and serve to supplement the observations made by the quenching technique. 2) Materials. Analytical-grade Fe2O3 and Cr2O3 were used as starting materials. Each oxide was first heated separately in air at 1000°C for several hours. Mixtures of desired ratios of the two oxides were then prepared. Each mixture was finely ground and mixed, and heated at 1250" to 1300°C in air for 2 hr, ground and mixed again and heated at the same temperature for 5 to 24 hr, depending on the Cr2O3 content of the mixture. A homogeneous sesquioxide solid solution between the two end members resulted from this treatment. A Part of some of the sesquioxide samples thus prepared was heated for 2 to 3 hr at 1300°C and oxygen pressures of 10-7 or 1.5 x 10-11 atm. Reduced samples (either iron chromite

Jan 1, 1964

By R. M. Asimow

Both smith1 and wells2 have shown that the dif-fusivity of carbon in austenite increases rapidly with increasing carbon concentration. Smith has shown, in addition, that part but not all of this increase can be attributed to the concentration dependence of the activity coefficient of carbon in austenite. From the work of Eshelby', it is known that, because of the image displacements, there is a uniform dilatation of the material in a body containing random centers of dilatation. It is thus tempting to explain the enhanced diffusivity as resulting from this apparent negative pressure caused by the interstitial carbon atoms.* That is, the activation free energy for diffusion is not directly a function of concentration if we consider that the alloy is subjected to a concentration-dependent pressure. To proceed with a quantitative solution, it is necessary to determine the activation volume AV for the diffusion process. An exact calculation of AV is quite a difficult problem and does not appear to have been solved as yet. A simpler procedure is to use the semiempirical, macroscopic theory of seyes' which relates the activation free energy AG to AV. Keyes has shown that for many types of diffusion processes the following relationship is valid Where p is the Gruneisen constant and x the compressibility. This relationship is based on the assumption that AG can be identified with strain-energy terms. In general there will also be contributions to AG due to a change in the energy of the valence electrons of the metal; thus the relation must be considered largely empirical. Surprisingly, for self-diffusion where it is well-known that the electronic contribution is quite important,' the Keyes relation works quite well for many systems. For interstitial diffusion where it might be expected that the relationship is on a firmer theoretical basis, the limited experimental data available is not in particularly good agreement as can be seen from Table I. However, it must be remembered that besides the uncertain basis of the Keyes formula there is considerable uncertainty in some of the experimental values of AV. The only real justification for using the Keyes formula in the present analysis is that it gives a result which satisfactorily solves the problem at hand and, further, there are no more reliable procedures for calculating AV available. The coefficient 3 in Eq. [I] is determined such that the room-temperature value for x is to be used. The activation entropy AS is estimated as 8.95 x 10"3 kcal per OK mole using the values in Table I1 and the Zener" relation AS = PAHIT, where p is a dimensionless thermal coefficient of Young's modulus which is to be evaluated at low values of T/T,, aH is the activation enthalpy, and T, is the melting temperature of the alloy. The resulting value of AG at 1000°C is 25.6 kcal per mole. The Gruneisen constant (p = 3cup/XC,), where p is the density, is evaluated from the room-temperature data in Table I1 after calculating C, from the relation. A value of p = 8.32 g per cu cm based on the value of a. in Table I is used. The result is C, = 5.0 x lo6 erg per g, H = 2.32, and AV = 3.41 cu cm per mole at 1000°C and infinite carbon dilution. It is assumed that the activation volume is not a function of carbon concentration. The theory could be refined to consider AV a function of concentration, but due to the uncertainties in the parameters there seems little justification for this. Carbon dissolved in austenite forms a nonideal solid solution, so that in writing an equation for. the diffusivity of carbon it is necessary to take into account the change in activity coefficient with concentration. The resulting equation is16

Jan 1, 1964

By Irving B. Cadoff, Ernest Levine

The crack formation and propagation in the single -phase Cu-4 pct Ag alloys were studied. The alloys were loaded in mercury to various stress levels, the mercury was removed, and the specimen examined for cracks. Cracks were found to develop below the fracture stress; the frequency of such cracks increased with increasing stress level. Some cracks were nmpropagative. Fracture in mercury was found to occur by the link-up of cracks formed at various stress levels rather than by the growth and propagation of a single crack. If the mercury environment is removed prior to a critical amount of crack formation, then continued loading results in ductile fracture. The appearance of the cracks at selected grain boundaries is related to the relative orientation of the boundaries, as are the propaga-tive characteristics of the crack. The mercury interaction appears to be one of lowering the strength of the metal-metal bonds in the high-stress area of the grain boundary. GRIFFITH'S microcrack theory1 proposed a critical crack size above which a crack in an elastic material grows with decreasing energy at a stress of From his theory it was proposed that the presence of a liquid tends to lower the surface energy of the microcrack faces2 leading to a decrease in the critical crack size necessary for spontaneous fracture propagation. stroh3 proposed that the stress concentration at a grain boundary due to pile-up may initiate a microcrack at the grain boundary. petch4 and Stroh5 evaluated the stress distribution at the head of a pile-up in a polycrystal-line material and deduced that the critical crack size and hence of is dependent on the grain size. Experimental verification of this dependence was found by petch6 for hydrogen embrittlement of steel. Studies in stress-corrosion cracking7 have provided a picture of fracture which shows that initial separations occur in a scattered, independent fashion in regions of high tensile stress. A minimum or threshold stress is necessary to produce a sufficient stress concentration to initiate frac- ture. These separations join up to form a crack. The extension of fracture is largely discontinuous and consists of a joining up of cracks. In recent worka evidence of this scattered crack network was found in a Cu-Ag alloy embrittled by mercury. For the Cu alloy-Hg couple, the crack path has also been found to be dependent on the orientation of adjacent grains, and with the addition of zinc to mercury a reduction in embrittlement along with a change in fracture morphology was found.9 In this present study, a mercury-dewetting method was used to observe crack initiation and fracture morphology when a Cu-4 pct Ag alloy is deformed in mercury and Hg-Zn solutions. PROCEDURE Specimens of Cu-4 pct Ag were prepared as in previous crack-path studies.' The specimens were heated at 770°C for 24 hr and water-quenched Tension tests using a table-model Instron were carried out in mercury and in various concentrations of Hg-Zn. Loading was in steps up to the fracture stress, with the load being removed and the specimen examined for surface cracks at each step. The specimens were dewetted after each load to permit examination of the surface structure and rewetted prior to continued loading. The specimens were wetted by electro polish ing in phosphoric acid, rinsing in alcohol, and then immersing in a pool of mercury. Dewetting was accomplished by flame heating the specimen for 30 sec in a vacuum. Some surface contamination was found, but not enough to obscure crack configurations and grain boundaries. RESULTS Fracture Characteristics in Mercury. Fig. 1 is a stress-strain curve showing the progressive step-wise loading of the specimen. As may be seen from the graph, the first position stopped at a is at a stress 5000 psi below the expected fracture stress of 25,000 psi. Examination of the specimen after removal of mercury showed only one crack. The appearance of this crack at a stress far below the fracture stress of this alloy in mercury did not affect the stress-strain curve in any manner. The specimen was then recoated with mercury and deformation was continued (curve b, Fig. 1) raising the stress by 4000 psi, and the same procedure re~eated. The initial crack was located and appeared as in Fig. 2 (crack lb). In this figure the crack is

Jan 1, 1964

IN the decade beginning 1850, the development by William Kelly in I the U.S.A. and Henry Bessemer in England of the pneumatic method of refining pig iron, known as the Bessemer process, gave the world the first method of producing low-cost steel in large volumes. Briefly, the Bessemer process consists of blowing air through liquid blast furnace iron in a refractory-lined vessel known as a converter. The air enters the iron in the furnace bottom through tuyeres, and during its passage through the iron removes the carbon, manganese, and silicon by oxidation. The heat produced by oxidation is sufficient to raise the temperature of the liquid metal to normal steel casting temperatures and, in addition, to melt some scrap. In the 1860's, the open hearth process was introduced which in the early part of the twentieth century surpassed the Bessemer process in steel production. In the early 1870's, Thomas and Gilchrist discovered that phosphorus could also be removed if lime were added and the converter lined with basic refractory; the modification is known as the basic Bessemer process and is used in Europe. Bessemer steel usually contains between 0.010 and 0.020 per cent nitrogen and between 0.05 and 0.10 per cent phosphorus which influences the properties. Henry Bessemer,1 in 1856, recognized the possibility of using oxygen in the converter process, but the cost was prohibitive. This interest was associated with the theoretical balance of the Bessemer process. Experimental work' has indicated that bottom blowing with pure oxygen results in serious converter bottom and tuyere erosion. Dilution of the oxygen by steam has been observed to be an effective means of maintaining low-nitrogen content of the steel and at the same time reducing bottom and tuyere erosion. A further advantage is that the fume emission characteristic of Bessmer operation is reduced. The addition of steam to the oxygen, however, reduces scrap-melting capacity due to the endothermic reaction characteristics of steam. The possible advantages of refining methods for steel using high-purity oxygen have been recognized for over a hundred years, but the develop-

Jan 1, 1964

By Voyle R. McFarland, Robert A. Burmeister, David A. Stevenson

The distribution of lead between phases in the Ag-Sb-Te system was studied using microautoradio -graphy. Two compositions were investigated, both containing an intermediate phase Known as silver antimony telluride as the major phase, and one containing AgzTe and the other SbzTes as the minor phase. For both compositions, two thermal treatments were used: nonequilibrium solidification from the melt and long equilibration anneals of the as-solidified structure. For each composition, lead was segregated in the minor phase of the as-solidified structure, but was distributed in the matrix after anneal. The electrical resistivity and carrier type were insensitive to the distribution of lead in the two-phase structure. ThERE has been considerable interest in the Ag-Sb-Te system because of its thermoelectric properties. The major interest has been in compositions on the vertical section between AgzTe and SbzTes, particularly the 50 mole pct SbzTes composition AgSbTez (compositions are conveniently expressed as mole percent SbzTes along the AgzTe-SbzTes section). One of the major problems in the proper evaluation and utilization of this material is the inability to control the electrical properties through impurity additions: all alloys prepared to date have been p-type, even with the addition of large amounts of impurities. It has been shown Wit all the compositions previously studied contain an intermediate phase of the NaCl st'ructure as a major phase (denoted by b) and a second phase, either AgzTe or SbzTe3, as a minor phase.'-3 One explanation for the unusual electrical behavior of this material is that the impurity additions have a higher solubility in the second phase than in the matrix; the impurity would segregate to the second phase, leaving the bulk matrix essentially free of impurity.4 In order to investigate this mechanism with a specific impurity element, the distribution of lead between the two phases was determined using autoradiography. Lead 210 was chosen because of the suitability of its 0.029 mev 0 particle for autoradiography and also because of the interest in lead as an impurity in this system.5'6 EXPERIMENTAL PROCEDURE Two compositions were taken from the vertical section between AgzTe and SbzTes, 50 mole pet SbzTes (Viz. AgSbTez) and 75 mole pct SbzTes, in which AgzTe and SbzTes appear, respectively, as the minor phase. Lead containing radioactive lead (pb210) was added to the above compositions to provide a concentration of 0.1 wt pct Pb. The material was placed in a graphite crucible in a quartz tube which was then evacuated and sealed. The samples were melted and solidified by cooling at a rate of 8°C per min and then removed and prepared for microa~toradiography. After autoradiographic examination of these samples, they were again encapsulated and annealed in an isothermal bath at 300°C for a number of days and prepared for examination. An alternate method of preparation employed a zone-melting furnace; the molten zone traversed the sample at a rate of 1.2 cm per hr and the solid was maintained at a temperature of 500°C both before and after solidification. This treatment had the same effect as solidification at a slow rate followed by an anneal for several hours at 500°C. In order to obtain the best resolution, thin sections of the alloy were prepared by hand lapping to a thickness of approximately 20 p. Other samples were prepared for examination by lapping a flat surface on the bulk sample. The resolution, although somewhat better in the former procedure, was adequate in both instances and the majority of the samples were treated in the latter fashion. A piece of autoradiographic film (Kodak Experimental SP 764 Autoradiographic Permeable Base Safety Stripping Film) was stripped from its backing, care being taken to avoid fogging due to static-electrical discharge. A small amount of water was placed on the sample, the film applied emulsion side down on the surface of the sample, and the sample and the film dipped into water in order to assure smooth contact. After drying, the film was exposed for 2 to 5 days, the period of time selected to give the best resolution. The film was developed on the specimen and fixed and washed in place. Two major factors must be considered in establishing the reliability of an autoradiograph: the in-

Jan 1, 1964