Search Documents

The Electricity Commission of New South Wales is the largest single user of coal in the State, burning some 8.5 million tonnes during 1972-73. This coal is converted in power stations into electrical energy which is then distributed throughout the State and supplies the electricity requirements of 99% of users in New South Wales. Barring any major change in energy consumption growth, or change in the current mode of power generation, the consumption of coal by the Commission is estimated to have a doubling period of from 10 to 14 years. Coal is used to generate up to 87% of the electrical energy sold, the balance being obtained from hydro gen- eration, mainly in the Snowy Mountains, and, to a much smaller extent, from diesel generation at Broken Hill. A very large proportion of this coal is consumed in pulverised fuel boilers in the Commission's power stations, located mainly on the various coalfields of New South Wales. Coal supplies are drawn from a large number of mines, some owned or controlled by the Commission, others being owned by public companies. The coals used, originate from at least ten different seams located in the northern, western and southern coalfields of New South Wales, and therefore have a wide variety of properties and characteristics. To ensure an adequate fuel supply well into the future, the Commission is continuously engaged in coal prospecting in various areas. Bore data is used in assessing coal reserves and is also the basis of economic studies for their possible future exploitation. The numerous coal cores obtained during drilling operations are carefully tested and analysed in order to assess their suitability for power generation purposes, and to provide data for the design and operation of boiler plant using these coals. In existing power stations coal deliveries are systematically sampled and tested for quality control, for pay- ment of purchases based upon certain quality parameters and to check for any possible plant operating or main- tenance problems that might arise from the use of the particular coals. Almost all the properties of coal that may be necessary in the Commission's work are obtained using standard testing procedures carried out by the Commission's chemists, in laboratories located at the various power stations or at its Central Laboratories in Pyrmont. Where specialised analysis or testing is required, this is ordinarily undertaken on a commercial basis by outside bodies, expert in the particular field. The significance of the various properties of the coal for use in p.f. boilers is outlined and related to their proper application to boiler plant design and to plant operation.

Jan 1, 1975

By Vutukuri VS, Budavari S

During recent years many investigators have suggested large spacing to burden ratios to improve the fragmentation obtained in blasting. In spite of these suggestions, most operators still use a conventional ratio of 1 to 2. From single hole longitudinal charge tests in laboratory, it is shown that burden controls the fragmentation. The burden for obtaining uniform fragmentation is smaller than the burden to obtain maximum breakage. Tests on two or three holes show that a larger spacing to burden ratio can be used for smaller burdens, but it is not possible for the larger burdens chosen to obtain maximum breakage. By using finite element analysis evidence is presented to show the effect of spacing and burden relationship on blasting results.

Jan 1, 1975

By Mark T. Atwood, Franklin B. Carlson, Louis H. Yardumian

The Oil Shale Corp. (TOSCO) is investigating the application of its oil shale retorting technology to coal processing in its 25-tpd retorting pilot plant. Low temperature char, with a high heating value, plus tar and gas have been produced from high moisture content, low heating value, subbituminous coal. The process, which has been named the TOSCOAL process, uses heated ceramic balls to provide the heat for retorting the coal. One ton of as-mined, subbituminous coal produces approximately 1/2 ton of char, 1/2 barrel of tar, and 1600 standard cubic feet (scf) of gas when the retorting is conducted at 970°F. Properties and yields of the products are presented and compared with Fischer assay yields.

Jan 1, 1975

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

By D. A. Paice, A. B. Shimp

Illegitimate loads on a mine dc power distribution system can be detected by measuring a superimposed ac current. To implement such a scheme, a 10-volt, 3-kHz voltage is applied at each dc power substation. By this means, the mine dc power distribution network, consisting of a feeder and trolley wires with a grounded rail return, is caused to serve also as a 3-kHz ac distribution network.

Jan 1, 1975

By Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodity in this volume has as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as fluxes, glass raw material, refractories, fillers, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Recent. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited avail- ability in certain areas. Limestone and dolomite are so useful and so abundant that in 1972 more than 690 million tons were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses, with emphasis on developments since 1960. In doing so we borrowed extensively from our recent report on the applied geology of limestone and dolomite (Rooney and Carr, 1971). The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired down in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1975

A case-study is presented of the tailings dam of Nairne Pyrites Pty. Ltd., at Brukunga, South Australia. The methods of-construction and operation of the dam are outlined over the whole working life of the mine. Procedures of soil mechanics used to estimate the stability 'of the face of the dam are described, and seepage problems are dis- cussed. It is concluded that the dam is basically stable, and enabled Nairne Pyrites Pty. Ltd. to dispose of tailings economically, although more attention to seepage control may have been ad- vantageous. Suggestions are made on the construction and operation of tailings dams elsewhere.

Jan 1, 1975

By R. V. Ramani, V. T. Burgos, J. A. McClay

This report was prepared by The Pennsylvania State University under USBM Contract No. G0111808. The contract was initiated under the Coal Mine Health and Safety Program. It was administered under the technical direction of DMSE, with Mr. G. R. Schottler acting as the technical project officer. Mr. J. A. Herlckes was the contract administrator for the Bureau of Mines. This report is a summary of the work recently completed as part of this contract during the period June, 1971 to September, 1974. Thls report was submitted by the authors on February 13, 1975.

Jan 1, 1975

By S. L. Crouch, C. Fairhurst

The general term "coal mine bump" refers to the sudden and violent failure of in-situ coal. Coal bumps occur in most countries where coal is worked by underground methods. They are related to geological factors and mining techniques. Coal bumps can be characterized as unstable releases of energy associated with yielding that occurs with progressive mining. Unstable releases of energy occur when the coal is able to absorb less energy than is released by the surrounding rock mass during the yielding process. At any stage of mining, the amount of excess energy so released is governed by the mining geometry, the overburden stress, the elastic properties of the rock mass, and the stress-strain characteristics of the seam material. If the coal in the vicinity of the working face is crushed, the peak abutment pressure occurs at some distance into the intact portions of the seam, and mining takes place in essentially destressed coal. With subsequent mining, additional yielding occurs, excess energy may be released, and the peak stress is again shifted into the solid. This process continues until the mining geometry is such that the zone of peak stress is effectively surrounded by yielding coal, at which point it can be anticipated that further mining will produce dramatic redistributions of stress and be accom¬panied by large releases of energy. On this basis, the differences between several alternatives for mining a given block of coal may be pronounced.

Jan 1, 1975

By S. Rajan

Familiarity with NEMA standards and the influence of the power supply on the motor-load system permits the user to make the necessary decision as to whether a standard or special motor is needed for his particular application. This paper highlights the more important aspects of NEMA standards for ac induction motors from the application engineer's standpoint and the effect of the power supply on motor characteristics.

Jan 1, 1975

By Golledge P

Safety legislation has a long history and widespread application, but how can one test its effectiveness? One way is to examine safety statistics. Another way is to compare the legislation with principles of good safety practice. Mine safety legislation contains many features that are widely accepted, and these should be examined critically to determine their importance. Uniform legislation and revision of legislation should be considered. INTRODUCTION

Jan 1, 1975

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By R. V. Ramani

This report is volume 1 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report contains a statement of the purpose and scope of work of the Grant, and provides an overview of the Master Design Simulator with a brief description of each subsystem. Also included is a discussion of several areas of application for the simulator.

Jan 1, 1975

By G. B. Sonneman

This final report summarizes the work done by The Bendix Corporation, Environmental Science Division, under contract to the Bureau of Mines to design, develop and test two improved systems for remote sampling the air at the working face of a coal mine in conjunction with approved portable methane detectors and machine-mounted methane monitors respectively. The work was started in May 1973 with preliminary design studies and was completed in May 1975. Five portable and two machine-mounted sampling systems were delivered. Contract "add-on" requirements for (1) modification of the machine-mounted system to accommodate a flame safety lamp and (2) a study of sensor response time improvement for the machine-mounted system were also completed.

Jan 1, 1975

By P. W. Jeran, C. D. Sullivan, C. M. McCulloch

A series of geological surveys were completed in six coal mines in connection with a Bureau of Mines research program on methane control. The aim of these surveys was twofold: First, to study the overall geology of the coalbed, and second to use the resulting data to evaluate the influence of the geological characteristics of the coalbed on safe and efficient coal extraction. This report explains the advantages of geologic maps and fence diagrams in coal mining, and how the knowledge gained from such geologic investigations of mines can help control many underground problems.

Jan 1, 1975

By Omnes G

Sixty Schlumberger electrical soundings were carried out in the Depot Springs area, near Agnew, Western Australia as part of an investigation into the availability of groundwater for the Agnew nickel project. The object of the survey was to locate calcrete aquifers related to Tertiary drainage channels on the Pre- Cambrian surface. The electrical soundings were initially interpreted using sets of master curves and auxiliary point methods. Electrical sections were produced and contour maps prepared of apparent resistivity for AB=80m, total conductance of the overburden and transverse resistance.

Jan 1, 1975

By Donald Towse

Geothermal heat might become an important fuel for several reasons: (1) To substitute for other scarce and critical fuels. (2) Because it may be less costly to the user than alternate fuels. (3) Because its production may be more profitable than production of other fuels. (4) Or for a number of other more or less non-economic reasons such as convenience or because of less environmental impact. In competition with conventional and other non-conventional fuels, geothermal heat must score well on one or more of those points. This study first considers projections of energy needs in several United States economic sectors and the technical possibility of geothermal heat substituting for other fuels in those sectors. Then, reported and projected costs of energy from geothermal heat are compared with costs of other fuels to show the relative costs of fuels in several economic sectors. Relative costs are reported from a sample of real and hypothetical geothermal projects. The actual cost of energy will vary with each application and the particular circumstances of each geographic location.

Jan 1, 1975

By Neil B. Young

Carbonate minerals constitute a major fraction of the oil shale in Colorado's Green River Formation. Quantification of carbonate minerals is important for the characterization of oil shale, particularly because of their thermal activity in production of oil from shale. The carbonate minerals found in this oil shale are nahcolite (NaHCO3), dawsonite [NaA1(OH)2CO3], dolomite [(Mg1-xFx)Ca(CO3)2], calcite (CaCO3), and ferroan [(Mg1-xFex)CO3]. Although carbonate minerals can be removed by acid extraction from the balance of the oil shale, direct determination of carbonate minerals is complicated by the occurrence of the same cations in more than one mineral. A method for assigning the acid-soluble cations to the individual carbonate minerals was developed from two assumptions based on oil shale geochemistry: (1) Calcite and ferroan do not occur together, and (2) the ratio of iron and magnesium is the same in dolomite and ferroan. These assumptions were tested by the Bureau of Mines by applying the technique for assigning cations to 219 samples from the saline section of the formation. The reported carbonate mineral amounts were compared statistically with X-ray diffraction peak heights, verifying the cation assignment method.

Jan 1, 1975

By Warner RE

SINCE 1952, when Elliott et a/ first applied the Sherwood correlation for flooding in chemical absorption towers to blast furnaces numerous investigators throughout the world have followed their example and much research effort has been spent to tighten the correlation and recently to extend investigation of flooding to side gas entry conditions. The widespread use of the Sherwood concept of flooding has been such that even the word itself has become an integral part of blast furnace nomenclature. The evidence for the applicability of Sherwood's relationship has been that the flooding limits calculated from blast furnace parameters lie approximately on the Sherwood line. However, the values of many of the variables for the blast furnace calculation are only estimates and at first sight one may wonder at such 'close' coincidence when some of the estimated parameters entering the Sherwood correlation are raised to the power of three or more, as for the bed porosity and the liquid surface tension. It is felt that the explanation of this result lies in the logarithmic: nature of the plot and/or the fortuitous can- cellation of the errors of the estimates in the calculations coupled with the fact that blast furnace fluid ratios lie within a very narrow range of values. The foregoing considerations should in their own right place doubt on the correctness of the Sherwood type flooding correlation applied to the blast furnace. Additional doubt regarding the existence of the Sherwood type flooding in the furnace has been cast by the results obtained in the Tokyo University experimental blast furnace. From the reasoning of both Standish and Colquhoun (p. 20) and Warner (p. 23) it is deduced that flooding in the traditional sense will only normally occur in the upper bosh (somewhere near the mantle), following softening as discussed by Palella et a/ on p. 75, and flooding in that zone is likely to result in furnace irregularity. On the other hand, the concept developed by Warner of slag hold-up above the raceways as a stable phenomenon not affecting furnace regularity is a process unique to the blast furnace and is not described by the Sherwood flooding theory. Recognising the considerable practical implications of slag hold-up above the raceways, this note further explores the physical process of slag hold-up. We envisage that bed of coke above the raceways in almost all blast furnaces would contain some slag held up by the gas pressure gradient. In general the slag would be contained in a ring and gas would bubble through in its ascent through the furnace. The force supporting this slag is the pressure gradient and obviously -much of the blast pressure is dissipated in supporting this structure.

Jan 1, 1975

By Oleg Terichow

Electrophoretic mobility measurements were made by the Bureau of Mines on samples of a Florida phosphate slime to determine the optimum conditions of coagulation and settling in an aluminum sulfate solution. Addition of anthracite to promote mutual coagulation demonstrated the practicability of heterocoagulation by reduction of the repulsive effect of double layers. By proper selection of the electrolyte and its concentration, the reduction of the double layers to a net zero point of charge causes the predominance of Van der Waals' forces of attraction leading to the coagulation and rapid settling of both particle systems, as is predicted by the Derjaguin-Landau-Verwey-Overbeek theory of colloidal stability. Confirmation was found in the microfiltration tests where a modified Carman equation was applied to evaluate the specific filter bed resistance.

Jan 1, 1975