Search Documents

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits; thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium.

By Fritz J. Klingler

From site demolition, to design, to construction, Detroit's new Tiger Stadium project is required to be completed within a short 2 ½ years from award of the design-build contract. Such extreme schedule requirements together with somewhat difficult ground conditions at the site, resulted in several challenges in the design and construction of the deep foundation system for the stadium. During the geotechnical investigation, an intermittent water bearing sand layer was encountered overlying the hardpan at the site. As a result, some concern developed regarding the potential for collapse of caisson bells within this layer, as well as the potential for flooding of the caissons during drilling. Although sand and/or ground water was encountered within about half of the caissons, standard drilling and belling methods were used, and adverse conditions were controlled in almost all cases through expeditious drilling, inspection and concreting of the caissons. This paper will present a summary of the ground conditions, design and specification requirements, and construction methods used to successfully install the caissons for this project.

Jan 1, 1999

By Lee Herold Storey

Groundwater remediation is growing in occurrence in the western United States. Groundwater remediation programs are regulated by state water quality statutes. The remedial action plans implemented under these statutes may conflict with well-established existing rights to withdraw groundwater for beneficial use. This paper discusses how the states of Arizona, Colorado and New Mexico administer conflicts between the need to withdraw and remediate groundwater with the existing rights of others to withdraw groundwater for beneficial purposes.

Jan 1, 1991

By E. Ordonez

I have read in the Bullentin a paper by H. von Hofer relating to the Origin of Petroleum, in ehich the author supports his and Englers views, express before, of the organic origin of petroleum.

Jan 1, 1915

By Ken Mills

Dartbrook Mine (Australia) works the Wynn seam, which has a moderate propensity for spontaneous combustion. Prior to any mining a commitment was made to place a segregation barrier pillar between longwall blocks 4 and 5. This was to segregate goaves and improve management controls in the event of a spontaneous combustion event within previous longwall goaves. An alternative to the segregation barrier known as a Consolidated Barrier was developed; firstly as a concept, then computer modelled and finally field tested. It consists of a wider than normal chain pillar with concrete Mega-Seals placed in cut-throughs. Permeability and stress measurements were conducted in the surrounding coal of the seal. Remote monitoring took place as the longwall face approached and then passed by the seal. Results indicate that as the longwall retreats past the seal, horizontal stress increases. The additional stress leads to an increase in confinement and a subsequent reduction in permeability.

Jan 1, 1999

By A. M. Gaudin

In the first place, let me thank you for inviting me to appear before you today to speak to you on "Mineral Industry Problems - Present and Future". It is a distinguished honor for me to have this opportunity, and I am highly appreciative of this distinction. The beautiful surroundings of Gatlinburg and the pleasantness of a summer occasion are a wonderful tonic for all of us, yet they should not blind us to the seriousness of our Industry's problems No doubt, because of my past appearances before members of the Society of Mining Engineers, at which I discussed wholly scientific topics, or research in the Applied Sciences, you may be expecting me to revert to these subjects. But I intend to venture in a field that is new to me, yet old to all of us, the field of Economics.

Jan 1, 1962

The opening session was held on Tuesday evening, October 23d. Mr. J. F. Lewis, on behalf of the local committee of arrange ments, made a short address of greeting to the members assembled, and then introduced Gov. A. H. Holley, of Lakeville, Conn. Gov. Holley addressed the Institute as follows: Gentlemen, we give you cordial welcome to a mining, manufac turing, and agricultural country, of which we are not a little proud. We welcome you as an association, and as individuals. We invite you to an inspection of our resources, and to our methods of im proving them. We appreciate the results of your efforts in past years, and we anticipate good from your advice and counsel in the future. You are in the vicinity of some of the oldest mining and manufacturing operations in iron in our country. It will be our pleasure to conduct you to a mine which was worked for more than a half century before our country achieved national inde pendence, and to point out to you the spot where the products of this mine were wrought into cannon and shot during the progress of our Revolution. We can show you also a far larger area of mining country than was supposed to exist in this vicinity at that early day. There are, within a radius of thirty miles from this spot, ten mines at least that have been extensively worked, and there are as many more that have been occasionally worked, with a fair degree of success. All the mines that are wrought to any extent produce excellent qualities of iron, while many of them in various combinations produce as good material for the manufacture of steel, car wheels, axles, and many other purposes, as can be found in ally country. The old Salisbury iron retains its reputation for tensile strength unsurpassed, when made entirely from the ore of the old mine. The progress that has been made in the development of these mines since the days of the pickaxe, when the product was trans ported in pounds upon horseback, to those of the steam-engine, which now moves hundreds of tons per day, presents, indeed, a

Jan 1, 1879

By Carroll C. Bailey, William F. Boericke

Mine financing, or providing adequate capital for developing and bringing a mining property into production, is an essential requirement for a successful operation. Today it presents a different picture than even twenty-five years ago. The day appears to be gone when a mining property could pay its own way from grass roots to production. The country has been quite thoroughly combed for surface showings from which sufficient initial profit could be immediately garnered to pay for further development and production facilities. The four M's for success in mining-mineral, market, management, and money-are still essential, but doubled or tripled wage costs and steep advances in cost of equipment and supplies throw increased emphasis on adequate capital funds for converting a prospect into a producer. Consequently, the old picturesque, although seldom rewarding, grub- staking procedure where a single venturesome citizen might advance funds to a prospector on a fifty-fifty basis for whatever discovery he might find, has largely disappeared. Its place, to some degree, has been taken by the small syndicate of venturesome members who band together for furnishing funds to a group of prospectors for the same general purposes. Such a syndicate has a definite organization and is usually assured of sufficient initial funds, or flow of funds, to carry on work for several years. It is usually headed by an engineer-promoter or an entrepreneur trader who has had considerable field experience as well as personal knowledge of his prospecting crews. For the owner of a potential mining property who has ample capital, the problem is to determine (1) justification for the necessary investment in exploration and development, and (2) the economics of the enterprise as to size and degree of integration of the ha1 operating entity. If the owner of such a property has little or no capital, he also faces these same basic problems but, in addition, must be able to present the findings of fact and persuade the prospective investor that the enterprise will produce

Jan 1, 1964

By Mark J. Zdunczyk

Short Mountain Silica mines the Clinch Formation, an orthoquartzite, for silica sand. The operation is located near Mooresburg, TN, about 80 km (50 miles) northeast of Knoxville. Short Mountain is a local geographic name given to an area of resistant sandstone (Fig. 1). The area is part of the Clinch Mountain system that extends from eastern Tennessee to southwestern Virginia. The thick sandstone unit is more technically called a quartz arenite (orthoquartzite) that forms most of the mountain. In 1980, a Knoxville resident brought the Clinch Formation - Short Mountain in particular - to the attention of the large silica-sand producers as a potential silica-sand mine. Working with a local contractor who owned several hundred acres on Short Mountain, the Knoxville resident contacted interested companies. Many silica companies reviewed the property including Ottawa Silica Co., Pennsylvania Glass Sand Co. (both now US Silica Co.),Unimin Corp.,The Morie Co. and others. AFG Industries was the main market for the glass sand product from this potential mine. It had two plants, both within trucking distance from the site. All the silica sand producing companies, however, declined to develop the site. A few years later, Unimin Corp. decided to drill and evaluate the deposit. From that evaluation, Unimin leased the property but later dropped it. The relatively limited market for the Short Mountain product as well as Unimin’s recent acquisition of Carolina Silica were reportedly instrumental in the company’s decision to let go of the lease. Several other companies-unrelated to the silica sand industry - looked at the site but no one was interested in developing it. In 1986, J.D. Nicewonder, owner of coal mines in Virginia and Kentucky, was approached to investigate the site. Nicewonder began to develop the site with the intent to produce glass sand to supply AFG Industries. In May 1988, the first shipment of sand was trucked to AFG Industries.

Jan 1, 1992

By Charles Wurms, Robert Steinitz

DURING an investigation to determine the compatibility of several metals with tungsten, the degree of reaction between tungsten and lead was determined. A literature survey showed considerable disagreement between the results of various earlier investigators. Information presented by M. Hansen1 states that, according to S. Inouye,2 tungsten has very poor resistance against attack by molten lead, even at the low temperature near the melting point of lead. A phase diagram in the same reference indicates a solubility of 30 wt pct W in molten lead at 1300°C. Contrary evidence was shown by Parkman and shepard3 in their investigation of materials for use in heat transfer systems containing liquid lead alloys; they performed experiments at 980°C for times up to 50 hr without noticing any appreciable attack on the tungsten. Tungsten sheet was immersed in molten lead contained in Vycor tubes evacuated to at least 10-4 mm Hg. R. Bernard4 and R. I. Jaffee5 also indicate that no reaction occurs between molten lead and tungsten. However, no experimental data were included in these reports. In order to settle the question of the solubility of tungsten in molten lead, tungsten powder with an average Fisher subsieve particle size of 6µ was pressed in a double-acting die at 6 tsi to small compacts. They were then sintered in an atmosphere of hydrogen for 2 hr at 1700°C, resulting in a sintered density of 64 pct of theoretical with final dimensions of 0.260 in. in height and 0.245 in. in diameter. For all tests, the tungsten pellets were immersed in molten lead. Table I is a summary of the experimental procedures showing atmospheres, temperatures, and times. The first experiments were performed at 650°C; at this temperature, the liquid lead should wet the porous tungsten better than at its melting point, and penetrate into the pores. The lead was heated in a graphite crucible with a graphite cover. No protective atmosphere was used, as it was expected that the formation of CO would be sufficient to prevent oxidation. This, however, proved to be wrong, and all tungsten samples showed a slight oxide film after treatment. The tungsten samples were immersed in the molten lead for times of 5 min, 10 min, 1/2 hr, 1 hr, and 2 hr. After this time, the melt was poured into a form and the

Jan 1, 1962

During recent years there has been a marked increase in the use of explosives in Queensland coal mines. Delay detonators have been introduced and their use has extended with the wider application of mechanised methods of mining.The need for careful study of the characteristics of delay detonators is stressed so that the advantages of simultaneous firing, from the points of view of safety and efficiency, may be obtained. With their use new potential hazards are introduced. These hazardsare considered and means whereby the overall safety may be improved are discussed.The increase in the number of misfires since the introduction of delay detonators is shown and the examination of misfired detonators is described. Lessons to be learned! from these misfires are noted and details are given of the essential requirements for safe and efficient blasting using delay detonators.INTRonUCTIONOne of the aims of mechanization in coal mines is to reduce the physical effort applied to the winning of coal. Explosives play an important part in achieving this and, following the introduction of power borers for the drilling of shot-holes in Queensland coal mines, much of the arduous work associated with coal getting has been eased. During recent years there has been a marked increase in the consumption of explosives, as shown in Table 1, and it must be the aim of all to use these explosives safely and efficiently. That there are dangers associated with the use Of explosives cannot be denied. The shotfiring operation is fully covered by legislation and, being under the control of one man, shQuld be capable of being carried out with a high degree of safety. The main source of accident appears to be the failure to take proper cover and this has resulted in...

Jan 1, 1958

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By R. L. Jones, H. Conrad

The effects of gain size on the room-temperature tensile properties of commercial(A- 70)-purity and iodide-purity titanium were investigated by concurrent tensile testing and thin-foil electron transmission studies. The mechanical tests showed that the effect of grain size on the yield, flow, and fracture stresses could be expressed by relations of the Hall-Petch type. The magnitude of the grain size effect on the yield stress was larger for commercial-purity than for high-purity titanium, but in both materials it was intermediate between that typically observed for fcc and for bcc metals. The effect of strain on the gain size sensitivity of the flow stress was found to reflect the grain size dependence of strain hardening. The electron transmission study indicated that the tensile behavior could be accounted for in terms of the dislocation densities and distributions formed during deformation. It was concluded that the effect of grain size on strength could be attributed to a relationship between grain size and the dislocation densities generated in initiating and sustaining plastic flow, the difference in stress levels being due to strain hardening. The relationships between recrystallized grain size, uniaxial tensile properties, and dislocation substructure have not been explored in any detail for a titanium. With titanium and its alloys finding increasing applications in aerospace systems, such information has become essential. The research described in this paper had two objectives: first, to document the effect of grain size on the yield, flow, and fracture stresses of unalloyed a titanium by the tensile testing of recrystalliied specimens at room temperature; second, to attempt an interpretation of the mechanical test behavior in terms of the dislocation structures formed on deformation, as observed by transmission electron microscopy of thin foils prepared from deformed tensile specimens. The observations reported here are restricted to room-temperature deformation; the effect of temperature on the yield and flow stresses of a titanium and the athermal nature of the contribution of grain size to the flow stress have been discussed elsewhere.1"3 EXPERIMENTAL DETAILS Two purity grades of unalloyed titanium have been investigated: Crucible Steel A-70, a typical commer- cial-purity product, and a high-purity iodide grade supplied by the Foote Mineral Co. Chemical analyses for interstitial impurity contents are given in Table I, together with values for the total interstitial atom fractions in terms of oxygen equivalents, which were calculated by the method outlined previously.4 ,5 According to the manufacturer's nominal analysis, the A-70 grade also contains about 3700 ppm of Fe. The A-70 grade was supplied as 1/4-in.-diam centerless-ground rod. The iodide grade was supplied as crystal bar which was consolidated to approximately 1/4-in.-diam rod by a single, rapid, molten zone pass, using electron beam heating. The 1/4-in. rods were cold-swaged to 0.078-in.-diam wires and 2-in. lengths were recrystallized in a vacuum of -5 x 10-5 torr, giving grain sizes in the range 0.8 to 30 . The thermal treatments and resulting grain sizes are summarized in Table 11. Since there was in no case any obvious sign of a bimodal dis tribution of grain sizes, the grain size values quoted in Table I1 are those obtained from mean linear intercept measurements involving >I00 grains. For the two coarse grain sizes the measurements were made using conventional optical techniques. It was noted during these determinations that the etchants used (10 pct HF; 30 pct HN03; 60 pct H20 and 2 pct HF; 2 pct H202; 96 pct H20 were both tried) etched grain boundaries very nonuniformly and optical polarization effects had to be employed to reveal boundaries which might otherwise have been missed. It was found that this problem became more acute with the finer grain sizes as the usefulness of polarization diminished.

Jan 1, 1970

By Robert C. Freas

Over the past twenty years people throughout the world, but particularly in the United States, have been taking an increasing interest in the environment, sources and causes of pollution, and pollution abatement. Air quality in the United States has been and continues to be an area of primary emphasis. In 1970, the US Congress passed the Clean Air Act and subsequently revised and strengthened it in 1977 with the issuance of the New Source Performance Standards. The Act has been further strengthened with the passage of the 1990 Amendments. By far the largest single source of sulfur dioxide (SO,) pollutants are coal fued electric generating power stations. Hence, a substantial portion of the flue gas desulfurization (FGD) research and equipment installation has been geared to the utility industry. Several competing FGD technologies were touted during the period 1970 to 1990 with varying degrees of success. Subsequently, the more successful technologies have been accepted, revised, and improved to the point that by 1991 third and fourth generation technology is available. A second area of emphasis for FGD has been coal fired industrial boilers. While individually they are much smaller than any electric utility generating station, they do represent a significant source of sulfur pollution. However, due to the size of industrial boilers and their location within industrial and educational complexes, the wet scrubber technology being employed by the utilities is not appropriate for these applications. Hence, fluidized bed combustion (FBC) technology has been developed for the industrial boilers. Since the installation of the first full scale test unit at Georgetown University, several equipment vendors have come forward with an increasing array of more sophisticated FBC units. Currently, FBC technology has matured to the point that the Tennessee Valley Authority (TVA), in cooperation with the Electric Power Research Institute (EPRI), has installed an FBC system on a 250 MW test unit at the Shawnee Power Station in Kentucky.

Jan 1, 1994

By L G. White

During 1958, prospecting parties working for the Mackenzie Syndicate in the Flat River area of the Mackenzie mountains, Northwest Territories, identified tungsten mineralization and located the property now being developed by the Canada Tungsten Mining Corporation Ltd. Scheelite mineralization, associated with pyrrhotite and minor chalcopyrite, occurs in lime silicate skarn replacement zones within a limestone-chert-argillite series intruded by granitic dykes originating from the ? main batholithic mass underlying the sedimentary beds. The results of surface outcrop sampling and 15,000 feet of grid-pattern diamond drilling have been combined to outline an orebody estimated to contain 1.32 million tons, grading 2.51 per cent WO after applying a 10 per cent dilution factor for mining purposes. T HE property of Canada Tungsten Mining Corporation Ltd. is located in the upper Flat River area of the Mackenzie mountains, Northwest Territories. Skarn-type replacement deposits containing scheelite mineralization are .situated between elevations of 4,500 and 5,500 feet above sea level along the east flank of the mountain range forming the boundary between the Yukon Territory and the Northwest Territories. The nearest supply center for the area is Watson Lake, Yukon Territory, located at Milepost 635 on the Alaska Highway.

Jan 1, 1963

At its meeting on June 22, 1950, the Board of Directors passed a resolution defining and expressing the policy of the Institute with respect to official participation or action in controversial matters On June 23, 1959 the Board of Directors made minor revisions in the resolution to bring it up-to-date with recent changes in the Institute's structure The revised resolution IS as follows

Jan 1, 1960

By W. D. Hausel

The Wyoming craton in the western United States is a favorable terrane for diamond deposits. The craton hosts a variety of ultramafic, ultrabasic, and ultrapotassic rocks. Additionally, a few hundred 'kimberlitic' heavy mineral anomalies and some geophysical and remote sensing anomalies indicate the presence of undiscovered, mantle-derived, pipes in the craton. The Wyoming craton is separated into a Wyoming 'archon' known as the Wyoming Province, and the Colorado 'proton' known as the Colorado Province. The 'archon' underlies much of Montana and Wyoming and continues north into Alberta and Saskatchewan; the Colorado 'proton' underlies much of Colorado and a small portion of Wyoming. Although most exploration geologists would consider the 'archon' the most favorable terrane for commercial diamond deposits, the 'proton' has produced more than 120,000 diamonds, while the 'archon' has not been very productive.

Jan 1, 1996

By Donald E. Crowell

Due to falling metal prices and depletion of ore reserves, lead- zinc mining in the Leadville, Colo., area gradually came to a halt in the 1950's. Exploration work continued, however, and by 1969 sufficient ore had been blocked out to warrant sinking a shaft and erecting a new concentrator to treat 700 tpd. The new shaft and concentrator were to be located in Iowa Gulch several miles east of Leadville at an elevation of 11,100 ft. The Leadville project is a joint venture between Newmont Mining Co. and Asarco, with Asarco being the operator. Design work began in the fall of 1969. Engineering was done by Torkelson Engineering Co. of Salt Lake City in conjunction with the central engineering department of Asarco. The plant was constructed by Stearns-Roger Corp. Construction began in the spring of 1970 and the plant went onstream in April 1971.

Jan 11, 1972

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By J. S. Stachulak

"IntroductionInco Limited operates nine underground mines on the rim of the Sudbury Basin. These operation s are situated near the city of Sudbury, 589 km west of Montreal, and 363 km north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite , and pyrrhotite. Total ore production from underground is in excess of 51 000 tons per day.The total volume of fresh air supplied to the nine mines is six million cu.ft/min. There are 50 main fans in operation at these mines, powered by electric motors totaling 11 200 kW (15 000 hp).The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The now of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential.There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Exchanger and Stobie Ice Stopes."

Jan 1, 1991