Search Documents

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By Stephen Krickovic

A degasification experiment was conducted in a Pocahontas No. 3 coalbed mine in Virginia. It involved (1) drilling holes in the coalbed in the out-side headings of a set of five being developed in virgin area, and (2) con-ducting a methane emission rate study as mining progressed and additional holes were drilled. Degasification from all drill holes except the longest in each of the outside headings and the first three drilled (excluding the in-situ pressure hole), was erratic and inconsequential in methane emission rates. The two longest holes liberated 66 and 79 cfm of methane, which is significant for the coalbed, but such quantity lasted a relatively short time; the first three were uniform but low in methane emission.

Jan 1, 1972

Minimize drilling time in roof bolting. Approach The Bureau of Mines conducted a survey of 34 roof bolting machines used in underground coal mines. Results of the survey indicated that drilling time, bit cost, and respirable dust concentrations and be reduced by using the appropriate bits for drilling, To evaluate bits currently used and to find optimum cutting parameters needed to minimize drilling time, the Bureau tested two bits commonly used in most underground mines on both wet and dry systems. These are the dusthog* and shank type. The dusthog has dust ports in the bit body to remove cuttings. With shank bits, holes in the drill steel do this. Cost of each type is roughly equal. Bolters with dry vacuum systems were tested in the laboratory first. The lab tests were verified by underground tests in several mines. Bolters with low-pressure wet drilling systems were also tested under-ground. Tests concentrated on the effect of rpm, water and airflow rates, heating, wear, bit design and bit type. Lab Results -Dry Drilling Holes were drilled during the laboratory tests using a production model bolter drilling 45-inch-deep holes into mixtures of lime stone and sandstone aggregate. All tests started with new shank and dusthog type bits at 225 and 450 rpm. Thrust was about 6,000 lbs in all tests. Each bit was tested at two airflows, 15 and 25 cfm, airflows which are typical on operating roof bolter bits. Eleven styles of bits were evaluated. On the average, dusthog bits drilled 25% faster than shank types and were always cooler after drilling. The effect of RPM was tested with 5 different bit types. When bit rpm was increased from 300 to 400, drilling rates doubled. With used, well-worn bits drilling time and final bit temperature were more than doubled.

Jan 1, 1986

By O. C. Blade

Production of crude petroleum in the Middle East (southwestern Asia) and in South America has increased greatly during recent years and has become a significant factor in the world's production of crude oil. Crude oil from fields in the Middle East increased from 256,164,000 barrels in 1946 to 305,833,000 barrels in 1947 and 417,201,000 barrels in 1948. Production from South American fields increased from 446,417,000 barrels in 1946 to 518,652,000 barrels in 1947 and 574,837,000 barrels in 1948. Crude-oil production from Canadian fields increased from 7,726,876 barrels in 1947 to 12,370,875 barrels in 1948, most of the increase being attributable to two fields, Leduc and Redwater, both represented by analyses in this report. Present indications are that production of crude petroleum from all these regions will continue to increase.

Jan 1, 1950

By George A. Savanick

The objective of this research is to develop a method for measuring the tensile strength at the interface between minerals in rock. These measurements reflect the strength of the attractive forces operating at crystalline interfaces in rock. Since these forces act in opposition to the forces set up in various rock fragmentation processes, measuring their strength may help in designing more efficient methods of rock fragmentation. The method developed for measuring the strength of intergranular adhesion in rock involves separating a bicrystal from the rock and determining the tensile strength at its solid-solid interface. This technique has been successfully applied to the study of quartz-feldspar interfaces separated from massive pegmatites, graphic granite, and the Rockville granite, yielding average tensile strengths of 5.86, 8.62, and 10.65 meganewtons per meter squared (MN/m2) (850, 1,250, and 1,524 psi, respectively). The data this technique provides indicate that the members of these bicrystals are strongly adherent. Examirtation of bicrystals broken at the crystalline interfaces indicates that the bonds responsible for this adhesion operate over only a portion of the interfacial area. This work conclusively demonstrates that tensile strength tests can be conducted on small selected areas; for example, grain boundaries in rock. The small-scale zones of strength or weakness determined in this way can be related to the overall strength of the rock.

Jan 1, 1972

By R. C. Hickman

"INTRODUCTION .As part of its spot drilling program, the Bureau of Mines core-drilled seven holes on the Alexander and Barber properties in Spartanburg County, S. C.Extensive surface float and outcrops of sillimanite schist on these properties appeared to justify drilling, which did not prove satisfactory, however, owing to the spotty occurrence of the schist bodies and the poor core recovery in the decomposed schist.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Ralston, chief, analyzes samples and performs beneficiation tests.This project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Alexander and. Barber properties are in the southern part of Spartanburg County, S. C. The Alexander property is about 5 miles cast of Woodruff. It is reached from Woodruff by driving east 5 miles on a macadam road to the intersection with an unsurfaced road near Unity Church. The farm house on the property is 0.4 mile north on this road. The sillimanite outcrop is in a field approximately 1,200 feet east of the farm house. The Barber property is about 2 miles north along the unsurfaced road that passes the Alexander property."

Sep 1, 1947

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat-room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Jeremy P. Doolan, Leigh B. Neindorf, Geoff W. Capes

The development and use of rock mass classification tools have been a key component for improving stope design over the past 4 years at the Xstrata Zinc George Fisher Mine in northern Queensland, Australia. In 2003, stope extraction data from 3 years of open-stope mining provided an excellent situation to review the assumptions in the feasibility study. Extracted stope profile information, drillhole geotechnical data, underground observations, and oral and written communication were used to develop a thorough stope reconciliation performance database. With-out collecting the back analysis data and presenting the data in a usable format, engineers are left to debate opinion instead of engineered judgment. This can lead to biased and uninformed design parameter choices with the potential to repeat poor design. This paper demonstrates some effective, practical examples of empirical data collection where rock mass classifications tools were developed and used to create improved confidence in predicting stope stability and failure profiles. The work contributed to design changes that resulted in a reduction in stope hangingwall dilution and an increase in head grade while continuing to ramp up production from 2003–2005.

Jan 5, 2007

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By G. W. Jones

During the course of an investigation by the Bureau of Mines into the causes, behavior, end control of anthracite-line fires, it was observed that the carbon monoxide disappeared from a scaled fire area much more rapidly than could be explained oil the basis of leakage of gases. Two suggestions were offered for this high rate of disappearance; (1) That the carbon monoxide was oxidized at temperatures below 150° C, by either the anthracite or its ash (tests on many anthracites have shown that at temperatures above 150° C carbon monoxide is liberated in the oxidation products when air is passed through it); (2) that the carbon monoxide was oxidized by micro-organisms present in the sealed area.

Jan 1, 1939

By G. L. Oldright

In the previous study that has been made by the authors on smelting in the lead blast furnace, the furnace examined was one that operated under conditions that have been considered as more or less normal up to the present time. That is although the furnace had in its charge a large portion of sinter, it also handled considerable quantities of naturally oxidized direct-smelting ore. Other ingredients, such as the limestone, were also added as fairly coarse material. The charges contained only about 24 per cent of lead. Until the changes incident to modern flotation began to take effect, many lead plants doing semicustom smelting in districts where competition was keen and much of the bonanza ore was exhausted were faced with the difficulty of obtaining enough lead to get a sufficient "lead fall" in the blast furnaces to clean the slag thoroughly and to separate it from the lead. A charge containing 24 per cent of lead would have been considered a very rich one by such smelters.

Jan 1, 1931

By Alvin Kaufman

Geothermal plants are competitive with conventional units. A geothermal plant can produce electric energy for 6.70 mills per kwhr, compared with 6.96 mills for coal, 6.74 mills for oil, and 7.04 mills for gas. These costs include fixed and variable charges. Potential for geothermal power exists in the Western United States, Alaska, and possibly Hawaii. Assuming that the current downward trend in cost per kilowatt of coal will cease and that the relative cost of gas and oil, already trending upward, may rise considerably more, geothermal energy will be utilized where available, in producing electric energy. It will be used in California first because it is directly competitive with gas-and oil-fired installations there. A long-term appraisal is difficult because little is known about the sources of geothermal power and the electric generating capacity which the steam fields will support. However, a market for geothermal steam-generated electricity exists within the Western States.

Jan 1, 1964

By Laurance L. Oden, Jack C. White, Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to field residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-off gas handling system, and thermal oxidizer for final off gas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 Ib/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kVe A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the off gas and serves as an acid gas scrubber. The clean off gas is heated to 1,800' F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 1993

By Carl L. Bieniewski

U.S. molybdenum production increased fivefold from 18.2 million pounds in 1946 to 90.5 million pounds in 1966, and constituted 87.3 percent of the total free world supply in the 1946-66 period. Mining development in other free world countries in the next few years may reduce the magnitude of the U.S. position, although similar development planned for the United States may counteract some of the relative gains by those countries. In 1966 two-thirds of the reported molybdenum consumption in the United States by end uses was as an alloying element in steel. Molybdenum also has important use as an alloying element in iron and high-temperature alloys. Consumption of molybdenum metal for making fabricated parts has increased in the past few years, especially in the space and nuclear industries. Molybdenum compounds are used mainly for making pigment, catalysts, and lubricants. Based on producer reports of shipments of primary products to domestic customers, U.S. consumption of molybdenum increased from 16.5 million pounds of molybdenum in 1946 to 65.6 million pounds in 1966. U.S. molybdenum reserves are now estimated to be 5.9 billion pounds of recoverable molybdenum, an increase of 2.1 billion pounds above previous estimates. Molybdenum ores account for 71.4 percent of the reserves, copper ores for 22.3 percent and copper-molybdenum, tungsten, and uranium ores for 6.3 percent. Several methods for predicting future demand are illustrated and estimates of demand using these methods were made for 1975. Based on present capacities and announced company plans for future developments, estimates of annual production were made for 1967 through 1975 for the United States, Canada. Chile, Peru, and the free world. These data indicate that molybdenum production in 1975 for the free world is expected to be 246 million pounds with the United States producing 68.2 percent and Canada, Chile, and Peru 30.3 percent.

Jan 1, 1970

By Jr. Norman

The Bureau of Mines investigated the thermoelectric properties of yttrium selenides and tellurides from room temperature to 900° C. X-ray crystallographic data were determined for the yttrium-selenium and yttrium-tellurium compounds that were orthorhombic with a cubic substructure. The yttrium selenides and tellurides exhibited semimetallic to insulator conduction properties with figures of merit of 10-9 to 10-4 °C-1. The mono-selenide and monotelluride behavior was partially degenerate; unsatisfied bonds were the source of the large number of charge carriers. The higher stoichiometry selenide compounds were intrinsic semiconductors) but with high electrical resistivities. A critical defect or impurity ionization energy for carrier activation appeared to exist in the majority of telluride compounds. Mobility and energy band determinations are required to interpret completely the observed effects in most of the compounds studied.

Jan 1, 1966

By George S. Koch

In preparing diamond-drill core samples for assay at the Homestake mine, Lead, S. Dak., 5-foot intervals of core are processed through three stages, crushing, grinding, and pulverizing, and portions of the core material are discarded after splitting at each stage of preparation. Then two 1-assay-ton fractions are taken from the pulverized material and assayed. This report investigates alternative methods of sample preparation. The consequences of crushing, grinding, and pulverizing all rather than part of the core are appraised through the statistical analysis of assay results from 118 5-foot intervals of core. Evidently, a substantial improvement in precision at small additional expense is obtained by grinding most or all of the core before splitting. Pulverizing all of the core would be desirable only if doing-so would cost less than assaying five random splits from each interval. Graphs and tables detail appropriate procedures to obtain specified precisions. The experimental design and methods can be applied to similar problems in preparing core and other geological samples.

Jan 1, 1972

By Joseph J. Wallace, Lloyd Williams, D. A. Reynolds, James J. Dowd, R. F. Abemethy

"SUMMARY AND CONCLUSIONS1. The investigation shows that the most important beds in Allegany County, from the standpoint of known recoverable reserves are: Lower Bakerstown, Upper Freeport, Upper Bakerstown, Upper Kittraing - less important beds are: Sewickley, Waynesburg, Pittsburgh, and Barton. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of coal in place, are estimated to be 556 million short tons, as of January 1, 1951. Of this total, 304 million short tons is in beds 23 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total eat ted reserves.3. Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand-loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Allegany County, as determined by this investigation, is 49.8 percent. This percentage is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. Based on the weighted average percent recovery for all beds in Allegany County, the recoverable reserves are estimated to be 152 million short tons as of January 1, 1951.4. The Allegany County coals are low-volatile bituminous in rank.5. The Allegany County coals are strongly coking."

May 1, 1953

By B. Dimitriades

Exploration of the photochemical reactivity of diesel-exhaust hydro-carbons is described. A smog chamber was built, and reactivities of diesel exhaust, gasoline exhaust, and propylene were measured at two chamber temperatures. Experimental data indicated the problems caused by instability of diesel-exhaust hydrocarbons. With reservations due to these problems, the results are interpreted to reflect comparable reactivities for diesel and gasoline exhaust.

Jan 1, 1971

By J. F. McCoy

As mining develops into deeper and hotter regions, the safety and health of miners require that the workspace be cooled. Toward this end, this program has successfully developed a high performance, low maintenance spray cooler of 5000 cfm nominal capacity. Further, a series of four 25,000 cfm, nominal capacity, spray coolers has been built and mine tested with satisfactory results. The smaller coolers have been patented and become commercialized with 50 units currently in service. The concept has been developed independently overseas with an unknown number of units in operation.

Jan 1, 1984