Search Documents

By Michael S. Moats, Addin Pranowo, Gerardo R. F. Alvear F., Nigel Aslin

The toxicity of arsenic is well known and documented. However, the presence of arsenic in copper electrorefining anodes and electrolyte is critically necessary to produce high quality cathode. Arsenic as well as antimony and bismuth concentrations vary depending on their relative concentration in the anode copper received from the smelter. This paper will discuss the behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance. This will include the minimization and mitigation of problems associated with arsenic, antimony and bismuth including cathode contamination, floating slimes, scaling and anode passivation.

Jan 1, 2014

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

By Q. Han

Irradiation of high energy ultrasonic vibration in metals and alloys generates oscillating strain and stress fields in solids, and introduces nonlinear effects such as cavitation, acoustic streaming, and radiation pressure in molten materials. These nonlinear effects can be utilized to assist conventional material processing processes. This article describes recent research at Oak Ridge National Labs (ORNL) and Purdue University on using high intensity ultrasonic vibrations for degassing molten aluminum, processing particulate reinforced metal matrix composites, refining metals and alloys during solidification process, welding, and producing bulk nanostructures in solid metals and alloys.

Jan 1, 2014

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By F. Sheykh-Jaberi, S. L. Cockcroft, A. B. Phillion

A coupled fluid/structure model has been developed to simulate semi-solid deformation in an industrial aluminum casting alloy, A356. Although this alloy has a significant eutectic fraction, nearly 50%, it still shows susceptibility to hot tearing. The model geometry consists of solid grains, created from a Voronoi tessellation of the domain, surrounded by liquid. The simulation is performed using the commercial codes, Abaqus Standard and Abaqus CFD. The solid model calculates the velocity, stresses and distortions in response to an applied uniaxial strain, and transmits them to the fluid-flow model, which computes the velocity and pressure fields in the liquid. It was shown that grain size and configuration, fraction solid and fluid properties all affect the semi-solid deformation behaviour.

Jan 1, 2014

This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. Basis of operation of the PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, online technologies through review of published information available for on-conveyor minerals applications. Case studies demonstrate benefits provided by this technology in two operating mines. An iron ore company had prior experience with the PGNAA analyser technology, implementing an early model in a minerals application in 2003 to develop confidence in its measurement performance and usefulness of the data. A number of analysers were subsequently included throughout the new plant design for extensive measurement and control of conveyed bulk flows, from conveying after mining through to rail load-out. A copper-gold company installed an analyser to address copper ore blending issues where an on-belt system was the only viable option for the degree of control required. Analyser suitability was evaluated through test work on site samples to determine customised multi-element precision guarantees for each application. Analyser results from normal operation are compared against laboratory analyses of multiple cross stream samples collected from conveyed flows to assess performance. Both projects discussed were able to realise benefits previously unattainable for plant quality control, surpassing capabilities of traditional technologies which were either unsuitable for measuring conveyed flows with adequate accuracy or in real time. Equipment payback within a few months was achieved for both sites. Through proven performance in these applications, the companies consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.

Jan 1, 2014

By M. Tanaka, H. Narita, T. Fuchikami, K. Morisaku, K. Nagao, T. Yoshida, K. Kuroda

The effect of various N-substituents on the performance of amide-containing tertiary amine compounds in the extraction of Rh(III) from HCl solutions was investigated to optimize the structure of these compounds for industrial use. It was found that N-2-ethylhexyl-bis(N-di-2-ethylhexyl-ethylamide)amine and tris(N-di-2-ethylhexyl-ethylamide)amine, which have long, branched alkyl chains, were suitable for Rh extraction, because they were soluble in a practical diluent (80 vol% n-dodecane?20 vol% 2-ethylhexanol) and stable against highly concentrated HCl/Rh solutions, and showed high selectivity for Rh(III) over Pd(II) and Pt(IV).

Jan 1, 2014

By T. Nomura, N. Saitoh, K. Tamaoki, Y. Konishi

We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from end-of-life products and electronics. We have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, that are able to reduce and deposit gold ions (Au(III)) or PGMs ions (Pd(II), Pt(IV) and Rh(III)) into metal nanoparticles at room temperature within 120 min. When processing the aqua regia leachate of printed circuit boards, Shewanella bacteria were able to rapidly and selectively collect gold ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. This biotechnological procedure also has the potential to allow the recovery of PGMs from the leachate of automotive catalysts. Shewanella bacteria were also able to successfully perform the complete reduction and deposition of the PGM ions. The ability to collect the PGM ions suggests that this represents a new process for the biorecovery of PGMs from used automotive catalysts. Our proposed biological method enables the rapid and highly efficient recovery of precious and rare metals via separation and concentration utilizing microbial reactions at room temperature.

Jan 1, 2014

By Farzad Mohammadi, Patrick Littlejohn, David Sanguinetti

Arsenic levels in metal concentrates are increasing as mining companies turn to developing low grade and complex ores. When arsenic bearing minerals are smelted, arsenic deports as gases which must be neutralized by a scrubber system. The resulting scrubber effluent is high in dissolved arsenic and requires treatment before the wastewater can be discharged or re-used. Conventional arsenic removal relies on lime addition followed by calcium arsenate formation and precipitation as hydroxides. As an alternative, arsenic removal with sulphide precipitation is receiving more attention due to potential advantages of the technology. Process streams high in arsenic often contain concentrations of dissolved metals that may be selectively recovered during sulphidization, producing a product that can be reprocessed and reducing waste generation. This paper will review laboratory testing completed for arsenic removal through sulphide addition and precipitation of arsenic (III) sulphide in combination with metals recovery to offset arsenic removal costs.

Jan 1, 2014

By B. A. Zaharov, J. M. Shneerson, L. V. Chugaev, M. T. Zhunusov, A. M. Markelov, S. V. Drozdov

The main direction of research was the application of autoclave technology for the flotation concentrates or biooxidation feedstocks. The industry modernization also expects the possibility of increasing the yield of the flotation concentrate, to allow an increase in gold extraction in flotation circuit. This paper provides brief description of results obtained for concentrates with the yield of 4 and 8%, as well as corresponding biooxidation feedstocks. Technological efficiency of autoclave oxidation is shown for both concentrates and biooxidation feedstocks. The process has been evaluated on a laboratory and a continuous pilot plant scale. Gold extractions from POX discharge are ranging from 94-97% for each product, with only 5-7 kg/t cyanide consumed.

Jan 1, 2014

By Rolf Andreas Lauten, Adam Pratomo, Dani Ramdani, Helminton Sitanggang

A universal challenge for the mineral processing industry is the diminishment of high grade ores. Instead, low grade ores, sometimes also containing problematic gangue minerals is the reality. With lower head grades the industry has to put more effort into processing to maintain the output and achieve suitable recoveries. In an effort to reduce the impact of declining head grade, a biopolymer was evaluated as an additive in the gold leaching operation at Antam Pongkor in Indonesia. Laboratory testing revealed that biopolymer usage lead to an increased gold recovery without apparent negative impact on the other parts of the process. Further plant trials revealed both a recovery increase around 1.3% and higher throughput (9%) in the presence of the biopolymer. Some scenarios that can explain these findings will be discussed.

Jan 1, 2014

By C. Y. Lim, H. W. Kim, M. S. Kim, J. H. Cho, Y. S. Lee

Al - 5.5 wt% Mg - 0.3 wt% Cu alloy strip was successfully fabricated by horizontal-type twinroll casting (TRC). For producing sound strips with no surface defect, the casting was conducted at various roll rotation speed, and the sound strip could be obtained at relatively low casting speed (3 rpm). The cast strip was homogenized at 450 °C for 10 hours, and then cold rolled with a reduction rate of 78%, followed by a final annealing at 450 °C for 1 hour. The annealed sheets showed good mechanical properties with approximately 330 MPa in tensile strength and 27 % in elongation, but exhibited strong anisotropy depending on the tensile directions. For the homogenized sheets, warm rolling was also conducted at 200, 300, and 400 °C. The tensile test results of the warm-rolled sheets showed that the rolling at medium temperature (300 °C) was proper to fabricate the sheets with relatively good mechanical properties and low anisotropy.

Jan 1, 2014

By Sergei Decterov, Peter Hayes, Evgueni Jak, Taufiq Hidayat, Denis Shishin

Copper smelter operations around the world are under sustained pressure to reduce costs and increase output. Through the provision of reliable data on fundamental properties of the chemical systems the opportunities for improvements of industrial copper production can be identified. Experimental and modelling studies on phase equilibria, thermodynamics of copper slag/matte/metal/gas systems have been combined into an integrated research program undertaken at PYROSEARCH. Experimental phase equilibria studies involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of compositions of equilibrium phases with electron probe X-ray microanalysis (EPMA). Thermodynamic databases development and modelling is undertaken using the computer package FactSage in conjunction with advanced models used for complex solution phases. Progressive development of these research methodologies has brought significant advances in characterisation of these complex systems, including a new optimised thermodynamic database for the copper-containing slag system Cu2O-Al2O3-CaO-FeO-Fe2O3-MgO-S-SiO2.The new data and models can now be applied to assist in improvements of the processes. The effects of changes to chemistry and process conditions within the smelting reactor can be examined. Several examples of new descriptions of the phase chemistry of the Cu2O-CaO-SiO2 and Cu2O-FeO-Fe2O3-SiO2 systems in equilibrium with metallic copper showing calculated and experimental data are presented.

Jan 1, 2014

By Ahmad Ghahremaninezhad, Noelene Ahern, Yeonuk Choi

Arsenic (As) is a toxic element and is a major contaminant in the extraction processes of some metals (e.g. gold and copper). Due to the toxicity of arsenic species, its removal from As-containing streams from extractive metallurgy processes and safe disposal is absolutely necessary. For nearly complete removal of waste arsenic species from metallurgical process streams, it is required to have arsenic in its pentavalent state (As5+ species). This study presents an oxidation process for arsenic species with air or oxygen gas as oxidant. Activated carbon (AC) or other carbon based materials are used to catalyse the oxidation reaction. Air or oxygen gas is the only consumed reagent which makes the economy of the process very attractive. The oxidation reaction can be carried out at ambient conditions (room temperature and atmospheric pressure) in less than 24 hours.

Jan 1, 2014

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

By Faan Bornman

"Reeves and Platt1 stated that dense medium separation is one of the most complex unit processes in mineral processing today particularly if cyclones are used. It is also the most efficient gravity concentrating process available to process engineers. The complexity of the process and large number of design and operating variables means that the process has largely remained more an art than a science. Dense medium separation is well established in the diamond, coal and iron ore industries but is gaining popularity as a pre-concentration step in other industries. The maintenance issues are addressed that will affect the efficiency of the operation.INTRODUCTION The purpose of the dense medium separation (DMS) process is to separate the valuable material from the waste based on gravity differences. However, the specific gravity difference between the two fractions must be large enough to achieve high efficiencies. Heavy particles sink through the dense liquid and light particles float. DMS is also used for the pre-concentration of minerals before further downstream processes like communition, in order to minimise the treatment costs. Examples are the pre-concentration of diamond ores or metalliferous ores like nickel, copper and cobalt. Dense medium separation is also used to upgrade the material to meet different market specifications, for example in coal and iron ore applications. A typical dense medium separation process for a diamond application is shown in Figure 1."

Jan 1, 2014

By Deng Yang-wu, Zhang Yan, Chen Chun-fei, Luo Xian-ping, Luo Cai-gui

This paper summarizes the ecological imbalance status of abandoned rare-earth element (REE) mines in southern China. These include large areas of vegetation damage, serious water and soil erosion, landslides, mudslides, heavy metal pollution, water pollution, soil contamination, and fluorine pollution. The causes which lead to the ecological imbalances at abandoned rare-earth mines are analyzed, such as: the inadequacies of using vat leaching, heap leaching, and in-situ leaching processes to extract REE resources; low mineral thickness and low grade of REE ore; and low utilization rates of the resource. Southern ionic REE resources are not fully integrated, with limited access and ineffective supervision of REE mining by relevant departments. The ecological recovery research for ionic-type REE mines is lagging behind, and there is no deployable ecological restoration method for REE wasteland. In the end, the following suggestions are made to improve the ecological imbalance status of rare-earth mine in southern China: develop new rare-earth extraction processes, accelerate the integration pace of REE resources, increase investment in ecological restoration research in rare-earth wasteland, and so on.

Jan 1, 2014

By N. Katsikaros, R. Agius, B. Adaszynski

"With stricter limits globally being imposed on cyanide discharge levels in plant tailings, having a reliable and well designed cyanide detoxification circuit is critical for any operation. The INCO SO2/Air method is most commonly used for cyanide detoxification where sulfur dioxide and oxygen combine to oxidize cyanide to the much less toxic cyanate. This paper discusses the steps involved with the development, from laboratory through to design, of a robust cyanide detoxification circuit. The goal is to produce a cyanide detox circuit that reliably meets discharge target with the lowest operating and capital cost.Design begins in the laboratory where continuous tests simulate full scale operation of a detoxification circuit. Detailed design relies on several design parameters, based on theory and experience, to ensure the reactor can satisfy requirements of the cyanide destruction reaction. Selection of the correct reagents and their supply to the reactor is important to an operable process with minimal operator workload. The operability of the system relies on correct process control strategies to maintain optimal reagent addition and chemical conditions in the reactor. These design factors are critical to providing a robust plant that will consistently meet cyanide discharge levels, ensuring uninterrupted production and plant profitability."

Jan 1, 2014

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By S. Kaushik

The control room in a mineral processing plant has become increasingly complicated with complex unit operations coupled with rapidly evolving systems of sensors and control. Even with significant automation, human intervention is required to counter various scenarios that play out every day. A typical control room operator must monitor over 300 individual points of data in order to ensure the safe and efficient operation of the plant. At the same time, the experience of the workforce is decreasing as operators retire and the new generation enters the concentrators. Global competition for skilled operators continues to be strong and the opportunity to apprentice has diminished. The challenge is to provide a skill foundation for the operators so that they can be effective in the concentrator in a timely and safe manner. Progressively, the industry is turning to dynamic simulation tied into the control system. The simulator environment operates behind the control system to emulate the plant operation, reacting as the plant would when a change is made. The operator drives the process, with realistic feedback, which enables learning in a safe environment. This paper will take the reader through a green-field case study and discuss the effectiveness of integrating an operator training simulator (OTS) on the operator’s learning curve.

Jan 1, 2014