Search Documents

By Eric R. Jette

In order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned. Heterogeneous Reactions The thermodynamic side of metallurgical reactions has received much attention in the past; the mechanisms, relatively, very little. The main reason for our present lack of information on the mechanisms of these reactions lies in the fact that every one of importance is a heterogenkous reaction; i. e., the substances involved in the reaction exist in more than one phase, while, if we neglect the large amount of work which has been

Jan 1, 1931

By A. B. Kinzel, Walter Crafts

Inclusions of nonmetallic matter have long been recognized as objectionable in steel. A complete theory of the effect of inclusions, which is consistent with that held today, was outlined in Howe's early work on the metallurgy of iron and steel. This, by analogy with wrought iron, assumes that the observed difference in properties between specimens with and across the direction of rolling is due to slag enclosures. The fact that wrought iron shatters in ballistic test is taken as an indication of the effect of inclusions on the resistance to'shock. Since that time, the development of the metallurgical microscope has shown the discrete nonmetallic inclusions in the iron matrix. Better resolution has brought out the great number of inclusions, and the availability of good microscopes in steel mills and laboratories has constantly drawn more attention to these inclusions. This recent emphasis on inclusions has resulted in studies as to their nature, mode of formation and methods of elimination, such as the work of Wohrman, Dickenson, Herty and Schenk. In addition to the published works, many investigations which have not been published have been carried out by private laboratories and have resulted in the application of specifications intended to limit inclusions in many qualities of steel. Neverthless, a clear understanding of the quantitative effect of inclusions on the physical properties of steel has been lacking. It is the specific purpose of this study to determine the quantitative effect of inclusions on the physical properties of steel that determine its behavior under dynamic stress. The study has shown that a quantitative relation between counted inclusions and impact strength does exist in normalized steels, but that factors other than readily visible inclusions are equally important. Furthermore, the present commercial rating of inclusions is unreliable with respect to counted inclusions or dynamic tests, and this study indicates that the tensile-impact test is more reliable as a measure of quality. General Scheme The general plan of the study follows: (1) To develop or establish a satisfactory measure of dynamic strength; (2) to develop or establish a

Jan 1, 1931

By James D. Sisler

Among the various studies made by the Coal Fact Finding Commission, appointed by President Warren G. Harding in 1922 to investigate all phases of the coal-mining industry in the United States and to report to Congress, was one concerning the amount and nature of losses in mining bituminous coal in the eastern part of the United States. This study was carried on under the direction of the U. S. Bureau of Mines. The writer was appointed field engineer to investigate the problem in Ohio, Pennsylvania and West Virginia. Some 400 mines were studied in these three states and conclusions were drawn from many sources of data. The summary report written by George S. Rice and J. W. Paul states that "the field reports indicate that the recovery in Ohio will remain about as at present, except in the Belmont district; whereas in Pennsylvania it will gradually improve, and in West Virginia it will improve rapidly." Since 1922, the writer has been interested in gathering material to substantiate or contradict these prophecies. Nature of Coal Losses There are six general causes of losses of coal in mining: (1) coal left on the roof and bottom; (2) coal lost in room, entry and panel pillars; (3) coal lost in oil-well or gas-well pillars; (4) coal lost under buildings, railroads and boundaries; (5) coal lost in handling and prepayation, underground and surface; (6) coal lost by rolls, thin or dirty areas and under streams. Local economic aspects that dominate the type of mining conditions determine to some extent whether certain losses are avoidable or unavoidable. In general, however, unavoidable losses include coal lost in the protection of buildings, streams, railroads, restricted properties and around oil and gas wells. Barrier pillars and other safety pillars are unavoidable losses as long as their size does not exceed the minimum for adequate safety. Natural physical conditions beyond human control, such as rock faults, clay veins, partings and binders, bad top and bottom, rolls and horsebacks, cause unavoidable losses. Unavoidable losses

Jan 1, 1931

By G. R. Fitterer

NONMETALLIC inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results. It is highly probable that some modification of the following

Jan 1, 1931

By C. C. Hagenbuch

Machine loading of coal into mine cars is increasing rapidly. Particular reasons for its use frequently apply to certain localities, but in general, it is profitable to install mechanical coal-loading equipment: (I) when existing hand-loading contract rates prevent further cost reduction; (2) when the height of the coal bed requires that either top or bottom must be taken to place cars in rooms; (3) when labor shortage or limited house-plant capacity prevents the production of desired tonnage ; (4) when tonnage requirements are in excess of possible hand-loaded production from developed areas; (5) when working places are scattered and it is possible to concentrate production, and therefore supervision, by the installation of mechanical equipment; (6) when rapid development is essential. Having decided to install loading equipment, the problem then arises as to what type is best adapted for a particular mine or coal bed, the choice lying between mobile track equipment, pit-car loaders, scrapers, shaker conveyors, belt conveyors and drag conveyors. MajoR FactoRs Influencing Choice of Equipment In determining the type of equipment to be used, the following major factors must be studied: Grades.—Adverse grades, while permitting other types of loading equipment to work successfully, may prevent the success of a shaker conveyor installation. Thickness of Bed.—The thickness of coal governs the choice of equipment. A machine that requires 5 ft. of head room should not be selected for a 3-ft. bed where otherwise it would be unnecessary either to brush top or to lift bottom. Nature of Pavement.—Soft or scaly bottoms are unsuitable for the use of any type of digging loader, shaker conveyors or scraper loaders. nigging loaders and scraper loaders scale the bottom, mixing it with the coal and causing preparation difficulties; shaker-conveyor drives frequently work themselves loose, destroying the conveyor alignment and creating maintenance problems. Nature of Roof.—With any type of loading machine, it is policy to obtain the maximum possible tonnage per move per set-up. This must

Jan 1, 1931

By T. A. Rickard

Slovenliness is as reprehensible in words as in clothes. Much writing that we recognize as poor in style is merely sloppy. Just as some students postpone the necessary shave or forget to change their collars, so young engineers in writing drop their articles, definite and indefinite, or omit prepositions where they are required, possibly to compensate for these they use unnecessarily The work will begin [on] Saturday. The work will begin [on] Saturday. `Influenza seriously affected many mines [during] the last three months. Flotation in America [during] the last two years has made tremendous strides. Construction of the mill started [on] August 12, 1915, at which time 75% of the excavation was completed. The idea I wish to convey is [that] there are mineral deposits to which the present law applies badly. For this reason, if there was [for] no other, the ownership of the ore below and [of] the surface above should go together. When a unit of mapping is furnished, be the unit a claim or [a] group of claims, it is necessary .. . A fully stocked store was started in Park City and all employees [were] sold merchandise on a strictly cost basis. The word "merchandise" is left without government or agreement. I suggest: ". . . and merchandise] was sold to all the employees on a strictly cash basis.". The verb `be' is serving concurrently both as a principal and as an auxiliary in the following: At first the work was interesting and [was] liked by most of the men. The sulphide ore was more complex or [was] milled at an increased cost. The failure to repeat tie auxiliary verb in successive clauses is a common error, as in The filter is filled with liquid allowed to empty, and then ignited.

Jan 1, 1931

By D. F. Hewitt

Page Introduction..............................305 Geologic features of eastern Oregon....................306 Geology of the Sumpter quadrangle....................306 Rocks older than the ore deposits...................307 Rocks younger than the ore deposits.............. . Lodes of the Sumpter quadrangle..................312 Areal distribution.......................312 Geologic distribution.................... . Major features of the veins...................313 Mineralogy and texture of the veins.............. . Ore deposits zonally disposed around the Bald Mountain batholith . 317 Summary of mineralogy and texture.............336 Zonal relations......................337 Ore deposits zonally disposed around Greenhorn Mountain batholith. 340 Zonal relations..................... . Relation of textural features to zonal arrangement of veins.....341 Summary of zonal relations.................. . Comparison with similar districts................. . Outlook for the district......................344 Introduction In an earlier report on the Sumpter quadrangle1 it was briefly stated that the quartz lodes of that region might be separated into several groups or belts on the basis of the kind and abundance of the minerals of which they are composed, and that these belts were disposed as areal zones around the principal intrusive mass of the region. When the opportunity to revisit the region was offered in 1929, as a result of a cooperative agreement between the State Mining Board of Oregon and the United States Geological Survey, it seemed advisable to pay particular attention to this feature of the lodes, in the hope that if the idea of zonal relations was confirmed it might serve as a guide in exploitation.

Jan 1, 1931

By Henry A. Ley

Kansas ranked fourth on the list of oil-producing states during the year 1930. Progressive statistics show that total production for the year will approximate 42,729,085 bbl. When final figures are compiled for Kansas the production may exceed this estimate, and thereby threaten the all-time record of 43,253,470 bbl. in 1918. Throughout the year the cumulative volume of potential drilled-up production has been increased by new discoveries and by extensions to proven areas in the territory west of the Nemaha (granite ridge) Range. Scattered drilling and leasing operations of a constructive nature occurred, but completions declined to the lowest levels in more than 11 years. Average initial production of current completions climbed to a new all-time high of 512 bbl. to the well. Proration measures were applied to the flush pools. The resulting shut-in potential production, as of December 15, is estimated at 110,000 bbl. This estimate is a wild guess. If all wells of the state were permitted to flow wide open for a period of six months production would not exceed 150,000 bbl. a day. The outstanding development of the year was an intensive drilling campaign in southwestern Kansas, which contributed at least 1,000,000 acres of contiguous natural-gas lands to the natural-gas resources of the United States. Production and Development Prospecting for oil in Kansas began shortly after the initial prospecting at Titusville. Operations and interest in the potentialities became active about 1870. This development was restricted to the shallow districts of northeastern Kansas. By 1895 operations had extended southward to the Oklahoma state line and sufficient prospecting had taken place to prove the potentialities of the state. Active prospecting was extended westward by the discovery of oil on the Nemaha Range in Butler County about 1916. The discovery of oil in Russell County added an extensive borderland province in 1923. The important discoveries of oil in Sedgwick County revived interests and operations throughout this territory in 1928. The development of widespread natural-gas lands in extreme southwestern Kansas during 1930 carried active exploration to the western boundary of the state.

Jan 1, 1931

By Alan Morris

IMPINGEMENT attack, as one of the types of corrosion suffered by condenser tubes, has been given a prominent place in corrosion literature of recent years. It has been reproduced and studied in carefully controlled laboratory tests. Much has been learned of its mechanism, and of the effects of variables such as temperature, amount of air, size of bubble and water velocity. Incidentally the technical public has been given comparisons between the behavior of some few metals under various conditions of impingement attack. The tests recorded here were undertaken in an effort to find at least some sort of qualitative answer to questions which arose occasionally as to the relative resistance of various alloys to impingement attack, and which could not be answered by reference to the literature. The final decision to start work on the problem was influenced in large measure by the nature of the water available in this particular place. The mill of the Bridgeport Brass Co. is located on the Pequonnock River at Bridgeport, Conn., within two miles of its mouth. The water is much like many other estuarine sources which are used in condensers, and which cause particularly severe corrosion. It seemed a most suitable water to use in such tests. As the work progressed an important seasonal variation was noted. The purpose of this note is to record this seasonal effect. The results of individual tests are given only incidentally.

Jan 1, 1931

By E. L. Davis

There have been many attempts to devise formulas for flowing efficiency and flow friction of oil-gas mixtures in oil-well flow tubes. Actually, however, flowing efficiency is rarely any real concern of the oil producer and flow-friction formulas contain so many unknown variables as to be of little, if any value. The production engineer is generally concerned with producing as much oil as possible with a minimum expense per barrel, and with the lowest possible net gas-oil ratio. These ends frequently are opposed to each other and the gas-oil ratio usually is sacrificed. In competitive operations, such as in town-lot fields, high current production is the sole interest. In conservative operation the greatest possible amount of oil obviously should be produced by natural flow unless the net formation gas-oil ratio can be improved by circulating gas. In practice this condition frequently exists. It would be a great advantage if the flowing condition of a well could be analyzed to determine the best possible producing status. Anticipating the death of a well so that gas-lift could be started immediately after the death, or preferably before, would save both production and expense. Frequently it happens that circulating gas fails to help a flowing well, or will not flow it after it has stopped flowing naturally. A knowledge of the laws governing flow would save considerable expense in testing such cases. A predetermination of probable pressures and amounts of circulating gas needed to flow wells and give best possible producing conditions would help in designing compressor installations. The optimum producing status of an oil well generally may be obtained by the conditions that subject the producing formations to the least possible back-pressure. This pressure is made up of the weight of the fluid column, frictional resistance to flow and the reaction from the acceleration of the fluid mass. A mathematical calculation of these components to arrive at a condition giving a minimum summation is impractical. Formulas would be complex and the results untrustworthy because it is impossible to assign proper values to the many variables involved.

Jan 1, 1931

By M. G. Cheney

The purpose of this paper is to review the more important developments in the production of petroleum during 1930 in Texas, excluding the Panhandle and Gulf Coast districts, giving emphasis to trends rather than to statistics. Outstanding Developments Aside from increasing curtailment of drilling operations and general prorating of production by state authority the most noteworthy developments for the year appear to have been: 1. Demonstrations of the fictitiousness of potentials as shown first by Darst Creek pool, rated at 180,000 bbl. and having actually 78,000 bbl. daily, and especially by the Hendricks pool of Winkler County, with potential of about 1,000,000 bbl. daily in mid-year and production of only 52,000 bbl. daily when opened to continuous full production in December. 2. Rapid development of the Darst Creek pool under competitive drilling. 3. Orderly and highly successful development of the Van pool under unit operation. 4. Failure of several highly rated structures southwest and northeast of Van. 5. Extension of the deep Simpson production at Big Lake and increased interest in these pre-Mississippian pays in North Central Texas and West Texas. 6. Discovery of prolific wells in northwest Rusk County from sands of Upper Cretaceous age, portending a rapid and extensive development campaign around the northwest margin of the Sabine uplift. North Central Texas It appears logical to discuss the new developments by districts as set out by the American Petroleum Institute, but North Texas and West Central Texas districts will be treated together. Pre-Mississippian,.—The pre-Mississippian beds, which in previous years yielded a few large wells in Young, Cooke and Callahan counties,

Jan 1, 1931

By P. W. Bridgman

It is a commonplace that experimental physics in the last few decades has discovered manifold complexities in the atomic and subatomic levels, where it was thought for hundreds of years that no structure existed, as is witnessed by the derivation of the word "atom" itself. The field of exploration opened by the discovery of the electrical structure of the atom was so fundamental, rich and stimulating, that it has been almost exclusively cultivated by physicists since they obtained their first intimations as to the nature of the basic facts. Only within the last few years has it begun to dawn on us that we have overshot an enormous domain in which are situated many phenomena of fundamental importance for all the practical uses to which we put matter in our daily lives; the domain, that is, of most of the phenomena of interest to the biologist and the metallurgist. Furthermore, we are beginning to find that this intermediate domain is not entirely simple, but that it contains unsuspected complexities, some of them derived from the complexities of structure on the atomic and subatomic levels, and some of them emergent as matter collects itself into large aggregates, which often offer the key to the explanation of hitherto baffling large-scale properties of matter. Today I want to describe and consider some of these newly discovered complexities in the behavior of matter in bulk. The application to metallurgical problems is not always direct, but I hope to be able to suggest that such general notions as to structure as those here discussed must have important reactions on our attitude toward the problems of metallurgy. Three different sorts of phenomena of this kind to which I shall direct your attention are (1) the so-called structure sensitive phenomena, (2) complexities of such a nature that they are masked by the presence of extraordinarily small amounts of impurities, and (3) complexities depending on internal molecular rearrangements which can be understood only from the point of view of the quantum theory.

Jan 1, 1931

By F. R. Hensel

Up to the present time few attempts have been made to produce hard nonmagnetic materials by heat treatment of austenitic steels. The usual result has been to cause them to pass into the martensitic stage, thus destroying to a great extent the typical austenitic properties, since this involves a transition of a portion of the iron from a face-centered to a body-centered type of atomic arrangement. High-strength nonmagnetic materials such as might be provided by properly hardening austenite are required in the electrical industry for different machine parts. In Europe nonmagnetic retainer rings for restraining the end-turns of the rotor windings in turbo-alternators have been developed as a special application of high-strength austenite. In testing1 a 28,000-kva. three-phase Siemens turbo generator running at 3000 r.p.m. at full load current, the losses in the short-circuit test were 450 kw. for the magnetic ring and 286 kw. for the nonmagnetic, and the difference should be attributable to the magnetic ring. The differences in temperatures during the same test are given in Table 1 and these show the advantage of a nonmagnetic over a magnetic retainer ring.

Jan 1, 1931

By B. B. Zavoico

The oil industry in the Soviet Union closed the 1929-1930 operating year fulfilling its assigned program. During this period of time, however, no basic improvements were noted within the industry. A careful study of the conditions indicates that disorganization in most branches increased continually; that supply and transportation problems are approaching a state of breakdown; that labor problems become increasingly difficult and that the estimates for 1931-1933 period are too large. The production of all Russian fields increased by 27,200,000 bbl., as compared with the 1928-1929 operating year, while the next year's program anticipates a further increase of 46,000,000 bbl., and the 1933 plans call for an amazing total of 330,000,000 bbl., or over 150 per cent, more than the production of the operating year that has just closed. Table 1 shows petroleum production in Russia by individual areas and fields from 1916, and furnishes estimates for the three coming years, which constitute the balance of the Five-year plan. A brief analysis of Table 1 will show that the Soviet Planning Commission anticipates that the fully developed fields of the Apsheron-Baku will double their production by 1933, .as compared with 1929-1930, and that the old Grozny fields, which are already showing a tendency to decline, will increase their output from 44,110,000 bbl. in 1929-1930 to 68,000,000 bbl. in 1933. Furthermore, in 1933 new fields are slated to produce not less than 100,000,000 bbl., a figure which even under most favorable conditions in Russia would be hard to achieve. Of course, Russia could develop such production, because the country is not lacking in the prospective reserves, but the transportation in the country today (as in the past.) is in such poor shape that neither the supply of a gigantic oil industry nor the movement of its products is within the realm of possibility. Table 1 shows the future estimated crude oil production as required by the Five-year plan, and also as reasonably estimated by the author, taking into account natural declines in old fields, slow development of new areas and the deficiency of the transport. While in the 1929-1930 operating year only two major fields underproduced (Surakany and Maikop) and the plan was fulfilled to the extent of 97.4 per cent., the production of the last three months of 1930 ("Shock Quarter") indicated

Jan 1, 1931

By Sidney Powers

CONTENTS PAGE Distribution of fields 4 History of development 6 Origin of oil 7 Structure,, accumulation and migration 8 Reservoir rocks 9 Methods of drilling and exploration to Oil-field statistics 12 Description by regions: United States: Appalachian region 12 East-central states 17 Kansas 18 Oklahoma 19 Texas 24 Arkansas 32 Louisiana 33 Mississippi -.. 34 Rocky Mountain region 34 California : 37 Canada 41 Mexico 43 Cuba 46 Bibliography 46 THE purpose of this brief account of the occurrence of petroleum in North America is to make available to those who have a knowledge of geology, but who are not engaged in the petroleum industry, a few salient facts about the location of oil and gas fields, their productivity, the important structural types of accumulation and the age of the rocks containing petroleum. A few useful data and statistics are furnished, yet not complete statistics that are available elsewhere. Geology has been treated in simple terms because the reader is presumed to have little interest in the names of formations and of oil sands. Mineral deposits are more or less analogous. Whether oil or metals, minerals are found in rocks, largely in sedimentary rocks which carry water or have at one time carried it. A genetic or accumula-

Jan 1, 1931

By H. H. Wright

In many fields edge water is one of the most important factors governing the production of oil. Possibly this fact is not appreciated by many producers except in so far as it may bring about a loss in production from wells drilled on the flanks of structures. In the light of artificial flooding as practiced in New York and Pennsylvania, and of the beneficial effect of natural water-flooding on many wells and leases in the Mid-Continent and elsewhere, it seems reasonable to suppose that very few phases of the petroleum industry hold greater promise for future benefit than the study and control of the natural water drive. Rate of Water Encroachment The rate of movement of water in artificially flooded areas has been referred to as so many feet per unit of time, usually from an injection well toward surrounding producing wells. This definition is vague when used in reference to the movement of natural edge water, inasmuch as such factors as sand thickness, steepness of dip and horizontal extent arc not considered. In the ultimate analysis, only the vertical component of movement affects the production of oil in the natural drive, and in order to define the rate of water encroachment more exactly, such a term as acre-fect per unit time might be used. Thus, where one well is located to each 10 acres a vertical movement of 5 ft. in the water level in a year would be defined as an encroachment of 50 acre-feet per year, and where one well is located to each 20 acres, as 100 acre-feet per year. Such a definition as this is entirely arbitrary, but it takes into consideration to a certain extent the influence of well spacing, and consequent sand drainage, on the rate of water movement. The rate of movement is considered to be an important function of water encroachment, for it is believed that the efficiency of recovery by natural water flood depends a good deal upon the rate of movement. In general, rapid encroachment is thought to effect a poor recovery because of the differential in favor of the movement of water through a sand body and the consequent tendency to trap oil in the sand. Slow movement, on the contrary, is thought to bring about a partial displace-

Jan 1, 1931

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a 'reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time' efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By Ernest F. Burchard

The Pao deposits of iron ore are in the State of Bolivar, Venezuela, near Upata, about 30 miles south of the Orinoco River and 90 miles east of Ciudad Bolivar. They were discovered 4 or 5 years ago and have not yet been developed to the stage of mining. In March-April, 1929, the writer devoted a week to the examination of these deposits. The maps, drill records and chemical analyses presented herewith were derived from original sources, and the field photographs were made by the writer. The petrographic and metallographic data are from notes by C. S. Ross and M. N. Short, of the U. S. Geological Survey, who have kindly collaborated in these special phases of the study. The Iron Obebodies Topography and Accessibility The deposits are in a region of low mountains representing northern outliers of the Guayanan Highlands. These mountains reach altitudes of 1800 to more than 2000 ft. above sea level, as determined by aneroid barometer. The iron ore is found on mountain crests that reach altitudes of 1915 to 1930 ft., and may be followed down precipitous slopes for 200 • to 300 ft. or more. The greatest vertical range in outcrop is nearly 400 ft., and drilling has indicated that the ore extends to this depth below the surface in one place, at least. The superior hardness of the iron ore accounts for the preservation of the local mountain crests with the intermediate valleys eroded in softer granitic rock. The deposits of iron ore are reached by a private road for automobiles branching northeast from the Ciudad Bolivar-Upata road, a distance of about 12 miles. This road was used in 1928-29 by trucks for transportation of food and camp supplies, gasoline, drilling equipment, etc., but was not suitable for the transportation of iron ore. Between Ciudad Bolivar and the iron-ore area the western two-thirds of the automobile road passes through nearly level, open country known as the savanna, largely used for grazing cattle. About 96 km. (60 miles) east of Ciudad Bolivar at

Jan 1, 1931

By W. B. Heroy

The rapid development of transportation routes on the African continent in recent years has greatly stimulated the demand for motor fuels and this in turn has led to more extensive exploration of such limited portions of the continent as seem to give promise of commercial oil production. In 1930, however, only two countries were classed as producers of petroleum and only one, Egypt, attained any importance. Egypt The petroleum production of Egypt is derived from the Gemsah and Hurghada fields on the west coast of the Red Sea and the Abu Durba, on its eastern shore in the Sinai peninsula. The Gemsah field, which began to produce commercially in 1912, has now practically ceased production, owing to the invasion of salt water. The Hurghada field has been producing since October, 1914. It now has about 60 producing wells. During 1929, a deeper sand with flowing produition was discovered in the eastern part of the field, producing oil of lighter gravity and free from water. The Abu Durba field was discovered by the exploration work of the Egyptian Government in 1918, oil having been found at a depth of 172 ft. This field has now 15 producing wells but a very small production. The production of these Egyptian fields over the last five years, is as follows: Metric Tons Metric Tons 1926......................... 172,881 1929....................... 271,520 1927......................... 184,557 1930....................... 277,146 1928......................... 269,324 This oil was all produced by the Anglo-Egyptian Oilfields Ltd., a constituent corporation of the Royal Dutch Shell group. During the year 1930 the Egyptian Government was engaged in geophysical prospecting of reserved areas along the Red Sea coast. Other Countries Soma1iland.—A geological survey of Somaliland was undertaken by the Somaliland Petroleum Co., Ltd., a subsidiary of the Royal Dutch

Jan 1, 1931

By Colin G. Fink, Leslie G. Jenness

Tantalum and columbium occur together in tantalite and columbite ores, which may be considered as ferrotantalate (FeTaz06), with part of the iron and tantalum replaced by manganese and columbium respectively, the general formula, therefore,becoming (Pe, Mn)O.(Ta, Cb)2Os. The ratio of tantalum to columbium is not fixed; the amount of tantalum may vary from one-third to three times that of columbium. Minerals having a high content of tantalum are called tantalite, while those possessing larger amounts of columbium are classified as columbite ores. These minerals are found in pegmatites and often occur in veins associated with cassiterite and wolframite, and may contain small amounts of tin, tungsten, titanium and si1ica. l Methods of Extraction Several methods have been proposed for the extraction of tantalum and columbium from their ores, among them being: 1. Fusion with Potassium or Sodium Bisu1fate.—The finely ground ore is fused with potassium bisulfate, after which the mass is boiled with water and the fusion repeated several times. The residue finally resulting is digested with ammonium sulfide to remove traces of tin and tungsten, boiled with hydrochloric acid, filtered and washed. These oxides are then dissolved in hydrofluoric acid, the silica evolved as silicon tetra-fluoride and the hydrofluoric acid solution used for the potassium double fluoride separation of tantalum. 2. Fusion with Sodium Carbonate and Sodium Nitrate.2—This fusion renders the tantalum and columbium soluble, and they are extracted

Jan 1, 1931