Search Documents

By Irwin R. Higgins

CONTENTS A. Introduction B. System Description C. Uranium Pilot Plant Programs D. Summary INTRODUCTION The Chem-Seps Continuous Countercurrent Ion Exchange (CCIX) contactor was first conceived of in 1951 at the Oak Ridge National Laboratory. In the 27 years that have passed, there has been a steady stream of pilot plant process development studies on a variety of processes far too numerous to mention. These have been in the area of water and waste treatment, chemical processing, ore leach treatment, and many others. Many successful production systems have been installed and operated in a variety of applications. A few of these are described herein together with a description of the system and its operational characteristics. SYSTEM DESCRIPTION Chem-Seps Continuous Countercurrent Ion Exchange* is a single loop in which various sections are separated by valves to isolate the sections performing different functions simultaneously. (Refer to Figure 1). To explain the working of a typical unit, let us use a simple configuration used in water softening or demineralization. The resin is moved in small increments by the hydraulic ram action. All solution flows are countercurrent to the flow of resin. The contaminants are removed in the process cycle and the resin is moved in the pulse cycle. A controller in the effluent stream from the treatment section senses the proper limit permissible in the effluent. In the process cycle, the influent enters through a set of distributors, moves downward and leaves through a set of collectors. Simultaneously the regenerant enters through valve RE and leaves through valve WA. The rinse enters through valve RI and its duration is controlled by an interface controller. In the process cycle, valves B, C, and D are closed, isolating all the sections. The duration of the process cycle is 4-10 minutes depending on the contaminants to be removed and is controlled either by a timer if the contaminants are fixed, or a controller in the effluent stream, if the contaminants fluctuate at short intervals. Valve A is open and resin is dropped to the pulse section simultaneously with the removal of contaminants in the treatment section, regeneration of loaded resin in the strip section, and rinsing of regenerated resin in the rinse section. As the resin drops through the valve A, it is backwashed to remove the suspended solids or resin fines. Removal of these fine particles is important to avoid the unnecessary pressure drop in the bed and plugging of the distributors. At the end of process cycle, all flows going into the unit and out of unit are automatically shut off. The valve A closes and valves B, C, and D open in proper sequence. A slug of water enters through valve PU, a predetermined incremental volume of resin moves into the regeneration section, an equal volume of regenerated and rinsed resin enters the bottom of the treatment section, and an equal volume of the loaded resin leaves the top of the treatment section and goes into the resin reservoir section. (The resin movement is plug flow with the Reynold's number being in the laminar region of the curve, and no fluidization occurs during the pulse cycle.) The total time required for proper sequencing of valves and the movement of resin is 20-30 seconds. At the end of this period, the valves B, C, and D close and valve A opens. The solution valves open and normal steady state operation begins. All valves are interlocked and properly sequenced. The resin movement is precisely controlled by sonic devices. Special Features of Chem-Seps CIIX "Downflow"*: The raw feed in the treatment section moves downward and the resin moves upward in the treatment section. The "downflow" of feed overcomes the handicap encountered in "upflow" systems. The "upflow" of feed requires a certain minimum flux during process cycle to lift the bed and keep it

Jan 1, 1979

BENEFICIATION AND CONCEN'TRATION; FROTH FLOTATION U.S. 4,069,144 - In the froth flotation beneficiation of phosphate rock using at least an acid flotation step and an amine flotation step, the crude ore is dried either during transport or storage or by air circulation immediately prior to classification, and the dried ore mixed with water and classified prior to flotation The preliminary drying substantially eliminates the usual problems with clay slimes G. C. Johnson and A. E. Schweizer, assigned to Mobil Oil Corp. Jan 17. 1978. 4 pp (209- 11) . Filed 1 1-19-75 (633,535).

Jan 1, 1979

By Don Hendricks, Alan Dahlstrand

Introduction The subjects discussed in this chapter deal with production planning, or more specifically, how the results of production planning may relate back to long-range planning and final pit design. The items discussed here are operating slopes, geometry, bench height, ore and waste faces, relationship to equipment selection, and computer methods. Many different ideas can be presented on these subjects, but this material is a recap of mining experience in the Butte ore body.

Jan 1, 1979

By R. M. (Mike) Robb

Introduction The requirements to investigate a wide range of alternatives and analyze a variety of ‘what if’ questions make the automation of pit design a requirement in today’s rapidly changing mining industry. The wide-spread application of computers has relieved the engineer of much of the tedious and error-prone work related to mine design. He is thus free to do the creative and innovative thinking for which he is trained. It is now possible to investigate a large number of alternative pit designs in a reasonably short time period. In the past it was very easy for a team of engineers to consume 12 to 14 man-months in the detailed hand design of a large open pit. The pressure of today's mining industry, the desire to investigate a variety of alternative designs, and the shortage of qualified engineers make the slowness of hand design less preferred.

Jan 1, 1979

The problems associated with the processing of the Tilden ore are very much representative of the problems encountered in plants processing fine grained magnetic and nonmagnetic iron ores. I would like to comment on some of the problems mentioned in Dr. Nummela'spaper and add to his list of research opportunities in the processing of iron ores. Grinding, the most important step in the processing of fine grained iron ores, is synonymous with liberation. One grinds to separate discrete grains of minerals from the gangue. By convention- al grinding in tumbling mills, mostly random size reduction is achieved with relatively little preferential liberation of minerals. Not only are discrete particles broken that should not be broken, but damage is done to the mineral surfaces. The combination of over- grinding and surface damage shows up in lower recovery figures and higher grinding costs. What is obviously needed is a better comminution process that is more discriminating and that would permit liberating mineral particles at the coarsest possible size with a minimum production of fines. Laboratory attempts at such preferential grinding have been quite successful, but technological difficulties have unfortunately prevented its use. Impact grinding is a good example of a new comminution process that has not been accepted because of equipment problems. Either these problems have to be solved or new comminution systems have to be developed to reduce grinding costs and improve liberation. In his paper Dr. Nummela mentions the change in the primary mill throughput that occurs during the winter months. Seasonal changes in the operation of the grinding circuit and other unit operations have been observed in many plants, and many explanations for this phenomenon have been advanced. The fact is that we do not fully

Jan 1, 1979

By Jack F. Havard, John S. Lagarias

When ore bodies are faulted or mill feed turns refractory, mining managers and engineers act vigorously to convert imminent failure into eventual success. The recent proliferation of onerous environmental regulations and restraints is likewise a threat to successful mining enterprise, in some ways more insidious and dangerous than the problems presented by natural obstacles. The regulatory burden has become so heavy that a pall of pessimism covers much of the mining industry. In this paper we frankly recommend an approach that does not just "make the best of it" but rather directs the whole environmental process: first, to improve planning, engineering, and operating procedures; and, second, to demonstrate the need for modification of laws and regulations which are intolerably burdensome to both the mining industry and the public.

Jan 1, 1979

By Michael B. Kahle, Fred J. Scheaffer

Production scheduling, along with production planning, provides projections of future mining progress and time requirements for the development and extraction of a resource. These schedules and plans are used by management as a means of attaining the following objectives (1) maintaining or maximizing expected profit, (2) determining future investment in mining, (3) optimizing return on investment, (4) evaluating alternative Investments, and (5) conserving and developing owned resources. The first four goals are generally concerned with mining costs, both capital and operating requirements, and as such, play an important role in production planning. However, this chapter is concerned with the fifth management objective of resource development in order to conserve and perpetuate the corporate entity. The following discussion is based on the premise that detailed economic evaluations and market surveys have been performed and analyzed and that the results indi¬cate a viable project.

Jan 1, 1979

By J. Y. Oldshue

INTRODUCTION The field of fluid mixing involves many different kinds of process objectives. In order to classify these objectives, Table 1 gives a listing of five basic application categories, gas-liquid, liquid-solid, liquid-liquid, miscible liquids, and fluid motion. However, each of these areas can be broken up into two different concepts one involved with uniformity of solids or liquids as a criteria, and the other involved with chemical reactions or mass transfer. The things that we would do to design a fluid mixing for solid suspension are quite different from things that we would do to design a mixer for heat transfer or gas-liquid mass transfer. Therefore, there are really ten separate mixing technologies. Each of these areas has its [ ] own principles of fluid mechanics, scale-up techniques and application experience. We will take a look at each of these areas and look at some of the ways that we can handle fluid mixing applications which.

Jan 1, 1979

By James R. Evans

Forecasting demand is an art as well as a science, and much personal judgment is required. National forecasts made for sand and gravel, crushed stone, and/or aggregate may be misleading or unhelpful locally. This is because of significant variation in demand within different geographic and/or political areas in the US, and/or the use of an inadequate data base and forecasting methodology. The best forecasts may be made for local or regional market areas, irrespective of geographic or political boundaries, provided a proper data base is available.1 The Bureau of Mines compiles detailed statistics on commodities sold or used in the construction industries and, therefore, is in an advantageous position to make national aggregate demand forecasts.

Jan 1, 1979

By James W. Dally, William L. Fourney, Anders Ladegaard Peterson

For the past 3 years, the authors have been conducting research sponsored by the National Science Foundation (RANN) to improve the process of excavation by drilling and blasting. The approach followed has been experimental where the development of stress waves and fractures initiated at the bore hole have been investigated in order to obtain a complete understanding of the dynamic fracture process. The second step in the approach has been to introduce modifications in the drill and blast procedure which will permit closer control of the fracture process. The laboratory investigations involve high speed photography where the dynamic fracture process is recorded with a Cranz-Schardin 1, 2 multiple-spark camera. The camera is equipped with 16 spark gaps which are pulsed at 25 K volts to produce an intense but very short (0.5 sec) flash of light. The camera is capable of recording 16 photographs of a dynamic event at framing rates which can be varied from 30,000 to 1,500,000 frames per second. The exposure time is sufficiently short to stop motion associated with detonating explosive charges and to make visible the details of the fracture process at a bore hose. The bore hole in a massive intact rock formation is modelled with a two dimensional plate containing a circular hole to represent the bore hole. The model material employed is a transparent polyester known commercially as Homalite 100.* This polymeric material is extremely brittle as evidenced by its extremely low fracture toughness of [ ]. The fracture toughness is a measure of the ability of a material to resist the propagation of flaws or small cracks. In comparison, Schmidt3 has recently measured the fracture toughness of Salem limestone and determined [ ]. Thus, the Homalite 100 should closely model the brittle nature of rock where fractures occur at small flaws and propagate without any apparent plastic deformation. Homalite 100 is also birefringent, which indicates that it becomes optically anisotropic when subjected to either static or dynamic loads. Circularly polarized light is transmitted through the loaded Homalite 100 model in a polariscope4 and the birefringence produces an optical interference pattern which is called a fringe pattern. For dynamic photoelasticity, the multiple-spark camera is equipped with polaroid filters to produce the circularly polarized light required to generate the photoelastic fringe patterns. An example of a singlespark frame showing a fringe pattern from a typical experiment is presented in [Fig. 1]. The photograph was taken 0.000072 sec (72 sec) after the detonation of the explosive charge. The circular fringes are due to the outgoing dilatational or P type stress wave and travel with a velocity of 85,000 in. per sec (2260 m/sec) in the Homalite 100. The P wave is followed by a second lower velocity stress wave known as the shear or S type wave which propagates at a velocity of 49,000 in. per sec (1245 m/sec). In the local neighborhood of the bore hole, several radial cracks are visible. These cracks propagate at essentially a constant velocity of 15,000 in. per sec (380 m/sec) prior to arrest. The fringes about the crack tips and in the local region of the bore hole are primarily due to the residual gases contained in the bore hole after the explosive charge was detonated. Sixteen frames similar to this one are recorded during the experiment to give full field visualization of the dynamic event at 16 discrete times over its duration. The fringe order number N is related to the difference in the principal stresses of and 02 according to a stress optic law4: [ ] where f0 = material fringe value, and h = model thickness. The wholefield dynamic-fringe patterns provide a basis for simultaneously observing the interaction between propagating cracks and the stresses which drive these cracks. Fracture Control Experiments Improvements in the efficiency of the drill and blast procedures must involve close control of the fracture process following the detonation of an explosive charge in a bore hole. By control it is implied that the number of cracks initiated and the location of each crack on the wall of the bore hole can be specified. Control also, involves orienting each crack and maintaining the crack path and velocity until the specified crack length is achieved. If the entire fracture process can be controlled, then rounds can be designed to optimize volume removed. fragment size and minimize costs. One area of blasting where fracture control is vitally important is in underground excavation where the strength and stability of the rock walls must be maintained and smoothness and precision of the walls must be achieved. The smooth blasting method is one of the most commonly employed procedures for achieving some degree of fracture control. In smooth blasting, the central region of material is first removed, and then the final row of closely spaced undercharged or cushioned holes are fired to remove the final volume and produce a smooth wall. In some instances, unloaded or dummy holes between the loaded holes are recommended to guide the fracture plane. This investigation pertained to an evaluation of 3 features of the smooth blasting process. These included (a) the effect of stress reinforcement on fracture by simultaneously firing 2 charges; (b) the influence of a dummy hole on control of the fracture planes between 2 simultaneously fired charge holes; and (c) the influence of dummy hole spacing on fracture plane control.

Jan 1, 1979

By John E. Carr

A bewildering variety of continuous thickeners and clarifiers are used in mineral industries and other heavy industries. General topes arc: ? Conventional thickeners ? Thickeners with flocculating feedwells ? Solids contactors ? Tray thickeners ? Lamellas ? Conventional thickeners with Lamellas ? High flow, fluid bed thickeners These units must be adapted to varied applications. They must provide operating flexibility to meet process needs. Such factors multiply the decisions which must be made prior to the selection of a thickener. The seven types of thickeners listed above, with their variations, share design concepts which limit their application and which can be used to evaluate their performance. Some of these arc: ? Feed velocities must be limited and/or controlled. ? Natural or reagent flocculation is necessary. ? Horizontal settling area is the basis for capacity. ? Overflow velocities must be limited and. or controlled. ? A controlled underflow is necessary. Thickener selection is the application of these needs to the basic process concepts. The basic function of a thickener, in the minerals industry, is the separation of a thickener sludge containing fine solids from water. In addition to this primary separation function, others include: ? Separation of solids from water ? Separation of flocculated solids from slimes ? Storage of solids ? Control of percent solids ? Storage of water ? Process control by absorbing fluctuations in feed ? Process control by increase in head clue to the depth and percent solids of the thickened sludge. Most thickener designs, suitable to minerals applications, are based on the separation of minus 65-mesh, 2.7 specific gravity solids containing slimes. These designs are routinely adapted to coarse and or denser materials. Materials of lower specific gravity such as coal, wood, char, some chemical precipitates and organics act Hike slimes if a thickener is used. Perhaps the most conservative approach to sizing and application is the use of comparative data from similar plants or similar industries. Thickeners are-routinely used in a great number of industries from which there is good historical information available. In the minerals industry, thickeners are used in: clay sizing, coal refuse, heavy media, copper concentrates, copper tailings, gold flotation concentrates, and countercurrent decantation for cyanidization in gold and CCD in uranium. Concentrate and tailings thickeners are used in iron ore plants, and concentrate and tailings units in lead-zinc plants. In addition, there arc thickeners designed to handle lime mud; limestone concentrates and tailings; phosphoric acid; potash; and rutile concentrates. Thickeners are, in addition, widely used in gravel plants for water reclamation. This gives excellent data on clay settling in some cases. Thickeners are used extensively for slurries generated by flue dust from wet scrubbers. Thickeners in flue dust applications are operating with considerable variations, treating blast furnace dust. BOF flue dust, and wood char. Similar applications are met in the power industry with fly ash and SO2 scrubber systems. Even though field data is preferred, such data has limitations as listed: ? Flowsheets are seldom identical. ? Data is often incomplete or limited. ? Ores vary significantly. ? Operating needs are changing. For these reasons, mathematical and theoretical methods are needed for application of field data to a specific project. In addition, laboratory data for similar projects and, if possible, laboratory data on a representative sample should be used to specify the thickener. There is a great volume of thickener literature. The references for this paper, along with their references, and past AIME papers provide excellent background. Older literature can be reviewed in light of current methods. It is interesting to note that the requirements for higher flow rate designs, more extreme flocculation systems, etc., can be logically introduced by reading Gaudin's Sections on Flocculation and Thickening, which was written before field installations could illustrate all of his ideas. The problem, then, is to select hardware which will take into consideration the functions of flocculation, separation of the solids, water clarity, control of the underflow, and control of the overflow. Reliable operation and simple control are customary.

Jan 1, 1979

By O. B. Bucklen, J. P. Matoney, P. G. Meikle, R. L. Terry

INTRODUCTION The trend in the coal industry for many years has been to make every- thing "bigger and faster." This also holds true for loading and storage facilities. Where once a 1 million st per yr (910,000 mt/yr) mine was rare, 3-5 million st per yr (2,730,000-4,550,000 mt/yr) mines are not uncommon today in the bituminous industry. This great increase in production, made possible through mechanization, requires greatly improved loading facilities just to get the coal away from the mine. Also, there is a trend to- ward combining production from more than one mine and cleaning it in a single preparation plant. In addition to increased loading capacity, this frequently necessitates raw-coal storage and blending facilities. The development of the unit train with its attendant economics has contributed more than any other factor to the widespread construction of storage and high-speed loading facilities. In the export market, the construction of ever larger coal colliers has added to the need for faster and larger loading facilities. In this climate of rapidly changing technology, any written ac-

Jan 1, 1979

By Clement K. Chase, F. Milton Lewis, Roshan B. Bhappu

In this paper an attempt has been made to review the cost trends in producing copper by conventional milling, smelting and hydrometallurgical means during the last five years. The primary objectives of this cost analysis are to provide a base for future projections as well as to indicate which cost items are more volatile in their influence on overall cost of producing copper.

Jan 1, 1979

By H. R. Green, D. M. Lamb, A. D. Taylor

The design of slurry launders has usually been based on strictly empirical concepts. An examination of the most common procedures reveals that they do not account for many of the variables that are recognized as significant for slurry transport. These may include flow rate, volume concentration of solids, solids specific gravity, solids size distribution, particle shape, launder geometry, and roughness of the wetted surface. It was decided to develop a design procedure, which would accomplish two things: First: Take into consideration most of the known significant variables and systematize the procedure to assure consistent results. Second: Provide a rational basis for examining and utilizing operating data to refine and improve the system. To accomplish this, it was necessary to develop a basic design concept. This concept has been developed through a complex development history, and yet still appears workable and technically sound. That concept may be outlined as follows: First: The solids transport velocity is the fundamental basis for slurry launder design. Second: The stream configuration, hence the launder size, is integrated with the solids transport velocity so that the actual stream velocity exceeds the solids transport velocity. Third: The launder slope is that which will achieve the

Jan 1, 1979

By Kenneth K. Humphreys, Joseph W. Leonard, Robert L. Llewellyn, William F. Lawrence

INTRODUCTION Cleaning fine coal sizes utilizing air currents in machines as the primary separating medium is called dry concentration or pneumatic cleaning. In 1947 approximately 18 million tons (16.38 million mt) of bituminous coal were cleaned by air machines; in 1965, 25.4 million tons (23.1 14 million mt); but in 1975, only 7 million tons (6.37 million mt). Table 11-1 shows the tonnages cleaned of bituminous coal and lignite in the United States by various types of equipment from 1938-1963. Table 11-2 shows only tonnages cleaned by pneumatic methods from 1964-1975. The decrease in tonnage to approximately 7 million tons (6.3 million mt) is due to a higher moisture content in the mined coal and the greater difficulty in cleaning the coal by air. There also was a definite trend to load raw coal at the mines, especially the slack which is the most expensive to clean due to the dewatering and drying requirements. While there have not been any applications of pneumatic cleaning in the anthracite field, its use has not been fully explored. The same is true for lignite and subbituminous coals.

Jan 1, 1979

By V. Annamalai, J. B. Hiskey

The kinetics of copper cementation on a rotating disc of pure aluminum were studied as a function of chloride ion concentration, rotational speed of the aluminum disc, hydrogen ion concentration, copper ion concentration, and temperature. The optimum experimental conditions for all the parameters were determined. Chloride ion was found to destroy the naturally existing aluminum oxide film, and enabled the cementation reaction to proceed. A two-step rate, observed in most of the experiments, was attributed to the attainment of a roughened surface. An Evans diagram for the copper-pure aluminum system was constructed and utilized in predicting the controlling mechanism of the system. At low temperatures (<33°C), the rate with an experimental activation energy of 20.36 kcal mol- 1 was controlled by the presence of an oxide layer. While at higher temperatures presence of an oxide layer. While at higher temperatures (>33° mol- 1 was controlled by ionic diffusion. The deposits obtained were pure copper and not a copper-aluminum alloy. The amount of aluminum dissolved was determined for each experiment, and the maximum excess consumption was found to be only 40%. The structural characteristics of the copper deposits were studied using a scanning electron microscope. These observations indicated that the deposits were either bulbous, massive crystalline, or dendrites of different degrees of fineness depending on the experimental variables. The reaction rates seemed to depend on the deposit structures in a predictable way when a particular experimental parameter was varied.

Jan 1, 1979

By J. D. Miller

The authors have summarized the state-of-the-art in the kaolin clay industry very well. In some instances the problems which they have identified are common to all fine particle separations and in other cases the problems are unique to the kaolin clay industry itself. General areas of research which may be common to other systems and which deserve continued investigation at a higher level of support include: 1) Establishment of the relationship between flotation response and clay structure/composition. 2) Determination of temperature effects in the separation of fine particles. 3) Evaluation of the effect of bubble size on the quality of fine particle separation. The first two areas would require basic surface chemistry studies including microflotation, electrokinetics, adsorption density measurements, and microcalorimetry. The last area would be oriented toward the mechanics of bubble-particle attachment. Regarding the first area, the authors alluded to this research need by commenting on the variation in separation observed from one deposit to another. It seems that a detailed study characterizing the flotation response of various clay types with respect to structure and compositional features would be of considerable value. For example, I understand, that D. W. Fuerstenau&apos;s group has recently been successful in characterization, with respect to structure, of some silicate mineral types--chain, sheet and framework silicates. A similar study should be initiated in which the flotation behavior of various clay minerals kaolinite, halloysite, montmorillonite

Jan 1, 1979

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

By J. C. Kerkering, J. C. Franklin, T. O. Meyer, R. W. McKibbin

A continuous survey of radon gas was made in two interconnecting stopes in a southwestern U. S. uranium mine to determine how the various phases of the mining cycle affected the radon concentration. The radon was monitored continuously with five detectors. One detector monitored the intake air, one the exhaust air, and three the stope air. The radon concentrations present during slushing, blasting, and exhaust fan shutoff were compared with concentrations on a nonwork day as a base level. Inside the stope, the radon concentration increased about 40% during slushing and 425% after blasting. Intake air radon increased 1600% and the stope air increased 550% while the surface exhaust fan was off.

Jan 1, 1979

By Stephen R. Holsinger

During 1972, Asarco&apos;s Silver Bell Unit embarked upon a project to test a digital computer-controlled grinding circuit against the performance of its other five grinding lines. The planning, implementation, and subsequent outcome of that project has been previously reported in a paper by Pittsl, et al. This paper will describe the solutions to major problems incurred during the implementation of this control strategy on the remaining five primary grinding lines. Changes made in operating philosophy and methods during the expansion will also be discussed.

Jan 1, 1979