Search Documents

By William E. Galloway, Gary E. Smith, Christopher D. Henry

INTRODUCTION Studies relating to the Oakville aquifer as presented in this report and by Henry et al. (this volume), are part of a larger , comprehensive examination of regional and local stratigraphic, hydro- geologic, and geochemical parameters within the Oakville Formation recently completed by the Bureau of Economic Geology. The Oakville serves both as a major Gulf Coast aquifer and an important uranium host (Fig. 1). Regional and local controls on hydrodynamics and hydrochemistry have important implications for hydrochemical exploration, the establishment of premining baseline parameters, and the design of post mining restoration procedures. Investigations of the Oakville Formation were de- signed for the purpose of determining the response of the aquifer to uranium extraction and were funded by the U.S. Environmental Protection Agency under grant numbers R-805357-01 and R-805357-02. Physical Stratigraphy Physical stratigraphic analysis shows that the Oakville Sandstone, a lithostratigraphic unit deposited by a major coastal-plain f luvial system, consists of five mappable, component depositional elements (Figs. 2 and 3). Each major component element is the product of one or more rivers traversing the Miocene coastal plain. In turn, each river possessed a unique sediment load, discharge characteristics, and source terrane. Consequently, each element exhibits distinguishing geometric and compositional parameters that potentially influence the flux and hydrochemical evolution of contained ground waters (Galloway, Henry, and Smith, in preparation). The Oakvil le Sandstone, as mapped and interpreted as a lithostratigraphic unit in the study area, corresponds closely to the Jasper aquifer system, an equally well-defined Gulf Coastal Plain hydrogeologic unit (Baker, 1978). Principal surrounding hydrogeologic units include the underlying Catahoula confining system, the Jasper aquifer system itself, and the overlying Burkeville confining system (lower Fleming mudstones). The Evangeline aquifer system includes much of the Fleming Formation. The Jasper aquifer system is bounded above and below by relatively less transmissive, finer grained confining systems, although absolute transmissivity varies greatly within both the Jasper and confining units. Lithostratigraphic and hydrogeologic boundaries coincide almost exactly within the Hebbronville flu- vial axis (Fig. 3). Correspondence of geologic and hydrostratigraphic boundaries is good within the George West axis; farther to the northeast the correlation of the Jasper aquifer with units mapped as Oakville Formation diverges to varying degrees. A complete analysis of these trends and a study of the depositional facies comprising the Oakvillle are included in Galloway, Henry, and Smith (in preparation). REGIONAL HYDROGEOLOGY The stratigraphic, compositional, and structural framework of the Oakville Formation and the mosaic of interrelated depositional facies that are combined in this framework play a key role in defining the hydrogeology of the Oakville. Furthermore, a combination of climate and hydrogeology, as well as past and present socioeconomic conditions, has determined water and land use patterns within the region of Oakville outcrop. Utilization of Oakville Ground Water Stratigraphic control for determining which wells produce ground water from the Oakville aquifer was established by preparing structural and isopach maps of the Oakville Formation using regional electric log cross sections. Surface elevation and screened interval data (or total well depth, if open-hole completion techniques were used) from each water well, combined with the stratigraphic data, allowed accurate assessment of the producing aquifer for individual wells. Information on well and screen depths, water levels, and usage of water from

Jan 1, 1980

By G. W. Phelps

The field of industrial minerals is concerned with both sieve size and distribution of sub-sieve particles. A great deal of work has been reported on the techniques designed to provide information of this work. The term sub-sieve is here considered to include particular material that will pass a 325-mesh testing sieve. Plant men require rapid, precise and simple testing techniques that are, if possible, inexpensive with respect to equipment and manpower. A number of particle-size procedures have been developed, based on the Stokes equation for streamline movement of a particle of diam D, moving at velocity V through a liquid of viscosity n. 1 Particles are considered to be rigid, smooth spheres, completely dispersed at low concentration and moving at low velocity through the suspending medium with no slippage between particle and liquid. In particle size determinations the particle moves either from natural gravitational forces or those provided by centrifugal means. The diagram of Fig. 1 shows a spherical particle of density S and diam D moving downward at velocity L/T (or V) through a liquid of density So and viscosity n. The forces of gravity G (natural) or Gc (centrifugal) cause the particle to move through the liquid, thereby creating a viscous drag F or Fc. Within the streamline flow

Jan 1, 1967

By E. A. Reilly, G. R. Gardner, F. P. Lasseter

THE methods that may be applied to the treatment of slurries and water, as these are related to practical coal-preparation problems, are concerned essentially with the movements of solids suspended in water. It is assumed that there are no fundamental differences between the principles involved in the treatment of coal slurries and the phenomena encountered in general mineral-dressing practice, and the latter are presented in some detail. Basic principles ,are correlated with present practice for both the anthracite and the bituminous coal fields, and methods are discussed which are designed to utilize best all the material subjected to treatment and suggest a sound approach to the solution of problems relating to the return of clear water to process or to streams. In order to approach the practical phases of the subject with sufficient understanding of the basic principles, it is necessary to discuss two types of phenomena that are applicable. The first is flocculation and the second is sedimentation. Descriptive matter is given covering the various methods and types of equipment employed to conduct these operations, with emphasis on their application to water and coal-slurry treatment. DEFINITION OF TERMS Definitions of terms are consistent with modern developments, and on form, in general, with their usage in mineral-dressing practice. Because of variations in coal-preparation methods, it is impossible to define a rigid upper limit of particle size for a coal slurry or sludge which will apply generally. Limits vary somewhat with the particular treatment method employed at a given plant. For purposes of definition, this limit is chosen as the particle size for which preparation methods such as Chance cones and jigs are usually dispensed with, and other methods, such as the Hydrotator, tables, and froth flotation, are employed. Generally the limit will be 10 to 6 mesh. In assuming this variable upper limit of particle size in a coal slurry, it is recognized that the size ranges discussed will duplicate sizes dealt with

Jan 1, 1943

The Pueblo plant receives its principal supply of iron ore from the Sunrise mine, located in Platte County, Wyo., and Iron Mountain, southwest of Cedar City, Utah. Limestone from Monarch quarry located on the continental divide above Salida, Colo., is shipped into Pueblo to be used as a flux. Of importance to the successful operation of the blast furnace plant is the ore preparation unit at Pueblo. Due to the geologic structure of both the Utah and Wyoming deposits, the ores, both high in grade, are quite variable in chemical and physical nature.

Jan 11, 1953

By Arthur H. Redfield

The West Indies are the summits of a submerged mountain chain, the continuation of which must be sought in the mountains of central Honduras. In Haiti, the chain divides, one branch passing through Jamaica and the other through Cuba, the Cayman Islands, and the Misteriosa bank. Suess divides the West Indies into three zones: The first zone is entirely of volcanic origin and includes many recent volcanic cones. It includes the arcuate string of islands, which extends from Saba and St. Kitts to the Grenadines and Grenada. The western half of Guadeloupe belongs to this group. The second zone consists of a geanticline, of which the sedimentary rocks range from the Jurassic to the Quaternary, but consist chiefly of Lower Tertiary sediments. In the west it is broad, including the whole of the Greater Antilles; but in the east it is restricted to a narrow belt, which includes the Virgin Islands (except Anegada), Anguilla, St. Bartholomew, Antigua, the eastern part of Guadeloupe and part of Barbados. The islands that compose the third zone are flat and low. Like the second, this zone is broad in the west and narrow in the east; it includes the Bahamas, Anegada, Sombrero, Barbuda, and part of Barbados. Geologically, Florida and the plain of Yucatan may be regarded as belonging to it. Trinidad and Tobago, though geographically adjacent to the Lesser Antilles, are geologically a detached part of the South American continent. The crystalline complexes of northern Trinidad and of Barbados are a continuation, en echelon, of the crystalline axis of the promontory of Paria. The folded Cretaceous and Tertiary of the central and southern parts of Trinidad represent a continuation of the folded sedinlents of the Paria district of Venezuela. Possible Oil-bearing Areas The volcanic islands of the inner arc of the Lesser Antilles may be excluded from consideration; these include Saba, St. Kitts, Nevis,

Jan 1, 1923

By Harold L. Bare, Frank R. Barnako

Coal mining historically has been a hazardous occupation but, in recent years, tremendous progress has been made in reducing accidental coal mine deaths and injuries. The purpose of this chapter is to discuss the basic principles of accident prevention as they are related to coal mining. Accident prevention fundamentals are no different for coal mining than for any other type of work. The fundamentals apply to all industries. Construction workers may be struck by falling tools and materials, and miners may be struck by falling slate and coal. Sailors may be trapped by shipboard fires, and miners may be trapped by mine fires. Railroad brakemen may lose hands and fingers positioning couplers, and miners may lose hands and fingers positioning couplers. Many other examples could be cited, but the point is that accidents that happen in coal mines are basically similar to accidents that happen in other industries. Thus, the basic principles for preventing accidents apply in coal mining as they do in any other type of work. COAL MINE ACCIDENT EXPERIENCE The US Mine Safety and Health Administration (MSHA) is the main source for accident experience data in coal mines. Coal mine operators are required, by law, to forward to MSHA monthly the number of fatal and disabling injuries, man-hours worked, and tons of coal mined. This information is compiled and published quarterly, with annual summaries, by MSHA. Trends in the number of fatalities and fatal injury rates are shown in Fig. 1. Major coal mine disasters, with number of miners killed, and dates of coal mine safety legislation are shown in Table 1. The fatal and disabling injury frequency rates for the coal industry are shown in Fig. 2.

Jan 1, 1981

By W. R. Ingalls

The manufacture of zinc oxide directly from the ore is one of the most important contributions that America has made to the metallurgy of zinc. Heretofore, this has been done chiefly for the production of zinc and zinc-lead pigments, and the method has been known as the Wetherill process. While that term may properly be applied to the process for pigment manufacture, it must be recognized that the principles of the process are of far wider application; and that there is going to be wider application in the immediate future is more than an expectation. I have in mind the use of the process as a method of igneous concentration. Igneous concentration is broader in its scope than the Wetherill process, for it may be done in the blast smelting furnace, or in the re-verberatory, or by other means. Igneous concentration is a rather clumsy term, and I prefer to introduce the new generic expression of "zinc burning," which is convenient, readily understood, and precise, for in all cases the zinc oxide is reduced to metallic form, is volatilized and is then burned to zinc oxide, the latter happening, however, after the zinc has been separated from the residue of the ore. As previously indicated, zinc burning may be done either in blast or reverberatory smelting, the gangue of the ore being scorified and drawn off as slag, while other metallic minerals are reduced to matte or metal. Such processes have heretofore been practised on fairly large scales. Thus, F. L. Bartlett smelted zinc ores at Con City, Colo., in specially designed blast furnaces, wherein the smelting column was only about 18 in. high. Such a limitation was necessary in order to prevent zinky accretions in the shaft of the furnace, which in course of time would have interfered with its operation. In running the Bartlett furnaces it was easy to bar them off, indeed, to poke right down into the smelting zone, and keep things going freely. Some iron blast furnaces in Virginia and the spiegeleisen furnaces of the New Jersey Zinc Co. afford other examples of zinc burning in blast-furnace smelting, although in their cases the happening is incidental rather than a primary purpose. Just as zinc may be burned off in a blast furnace, so also may it be done in a reverberatory. Indeed, there is less trouble, in some respects, in a reverberatory, for therewith there is no shaft in which accretions may

Jan 1, 1918

By Edward Walsh

In the early history of the production of metallic iron from the native oxides or ores, success attended the labors of the workman according to the care he devoted to his work, and according to the degree of skill he possessed in furnishing the required amounts of fuel and ores to be acted upon by the blast propelled by the bellows, trompe, or wooden tub, and delivered into the hearths of the Persian, bloomery, or Catalan forges. The same skill may also have been of avail in the use of the lower forms of the ".Stück," "Blue,"or" Wolf"

Jan 1, 1887

By Tasuku Fuwa, John Chipman

Equilibrium data on the reactions of gases with carbon and oxygen dissolved in liquid iron are reviewed and correlated. A source of error in oxygen analysis of graphitic samples is exposed. New experimental data on the oxygen content of high -carbon iron in equilibrium with carbon monoxide indicate that the activity coefficient of oxygen is decreased by additions of carbon. The carbon-oxygen product decreases slightly with increasing carbon content. In recent years a number of investigations have been reported dealing with the equilibria between carbon and oxygen in liquid iron and gases containing carbon oxides. The laboratory study of these reactions dates back to 1931 with the publication of a paper by Vacher and Hamilton' on "The Carbon-Oxygen Equilibrium in Liquid Iron". The principal object of this study was to obtain data on the reaction shown by Eq. [3] below; their data and others by vacherZ permit evaluation of the other equilibrium constants as well. Subsequent studies have been reported by Matoba, Phragmen and Kalling and by Marshall and Chipman.5 The equilibria may be expressed by the following three equations: C + CO,= 2CO;Kl = Pc° [1] 0-+CO = CO,;K2=-P co, "0.PCO c + O = CO; K3 = In the equilibrium constants, ac and a0 are taken as equal to [% C] and [% 0] respectively in the infinitely dilute solution. At finite concentrations an activity coefficient is introduced such that ac =fc [%C], and so forth. It is to be noted that these equations represent only two independent relations, the third being derivable from any two. Richardson and Dennis have determined the conditions of equilibrium in reaction [I] at temperatures of 1560" to 1760°C. Their results have been confirmed by Rist and chipman7 who have shown how the data may be extended to cover the entire range of liquid compositions at temperatures from the eutectic up to 1760°C. An approximate confirmation has been reported by Fuwa and chipman.' These investigations also established the activity coefficient of carbon which was shown to increase rather rapidly with increasing concentration. For the very dilute solutions the value of Kl is expressed in the equation: log^i = - 7280/T+ 6.65 This equation leads to a value of Kl = 430 at 1540° C in excellent agreement with the average value of Marshall and Chipman.5 It is shown as line 1 in Fig. 1 together with the experimental observations. In the case of reaction [2] the direct experimental results can be supplemented by observations on the corresponding reaction with hydrogen, namely reaction [4]:

Jan 1, 1961

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

In the January 1956 issue: TP 4137B. Adsorption of Ethyl Xanthate on Pyrite. By A. M. Gaudin, P. L. de Bruyn, and Olav Mellgren. P. 65. Since P. L. de Bruyn is now a member of the AIME, the word "associate" should be removed in describing his status. The address of the third author, Olav Mellgren, should read: 74-2 Chingola, N. Rhodesia. P. 68, second paragraph, last line: the word "300-fold" should be replaced by "3000-fold." Also in the January 1956 issue: TP 4158B. Energy Transfer by Impact. By R. J. Charles and P. L. de Bruyn. The authors wish to express their disapproval of the omission of the abstract from the article, since they believe that an abstract fulfills a very important function in every paper.

Jan 1, 1957

By S. K. Bradford

For years past I have traveled in quest of promising mining-properties, over almost impassable mountain-trails to remote places in the mining-regions, usually many miles from an assay-o5ce. If, upon examination, the fornlation and the ore-deposit appeared favorable, a quick determination of the value of my samples was necessary, in order that I might take intelligent action with reference to the acquisition of the property. A journey with my samples to civilized regions often meant weeks of delay, and perhaps loss of opportunity. How many, under similar circumstances, have returned with their assay-results from such a journey, only to find that some audacious speculator had optioned" the property! True, a first payment could have been made and the chances taken on the results; but experience has taught that rich-looking ore is not of necessity valuable. Personally, I would not hazard a ten-dollar bill on any property without first determining by assay the value of the ore. To carry the usual complete assay-paraphernalia over such mountain-trails was impracticable by reason of the loss of time involved, the great expense of transportation (charged -

Jan 1, 1911

By Oren C. Baptist, Eliot J. White

Samples of four reservoir sands having different degrees of water sensitivity were subjected to several laboratory tests to determine differences in capillary behavior attributable to clay-mineral effects. The degree of water sensitivity was estimated by the difference between gas and water permeability. Unsaturated pore volumes determined with mercury injection were comparable to irreducible water saturations determined with the semipermeable bar-rier method only for the non-sensitive sands that contained small amounts of non-swelling clay minerals. Irreducible saturations were independent of salinity of the water, which suggests that most residual water is adsorbed 0.7 a film over solid surfaces and that internal retention by clay minerals is relatively insignificant. The water-sensitive sands imbibed water to higher saturations than did non-sensitive sands, and this result is believed to be a combination of the effects of clay minerals and preferential wettability; however, the relative importance of each of these effects is riot determinable. Thus it is concluded that the semipermeable barrier method is the best of the laborafory methods used for estimating formntion water .saturations in the sands studied. INTRODUCTION This investigation is a continuation of studies of the role of clay minerals in petroleum production in the Rocky Mountain area. Previous work has shown large differences in gas and water permeability in numerous reservoir sands; these water-sensitivity effects observed in the laboratory have been correlated with well behavior in the field, and the degree of water sensitivity imparted to reservoirs by the various clay minerals has been determined.'.' The effect of interstitial clay minerals on formation water3 saturations is not so well known. It has been reported that formation water saturations probably are higher in clayey than clean sands,' but this effect has not been evaluated in the laboratory, and the relative effect of the various types of clay minerals on formation water saturation has not been determined. The clay-mineral groups of most importance to this study and to petroleum production in general are kaolinite, illite, and montmorillonite. The minute layers of montmorillonite are loosely bound to one another so that water enters between them, causing great expansion of the particles. Kaolinite and illite do not exhibit interlayer hydration, but they do immobilize considerable amounts of water owing to their large surface areas, which are of the order of 15 to 97 m2/gm of clay.5 The four Wyoming sands used in this study were selected to represent a wide range of water sensitivities. These sands, with the number of wells and fields from which the samples were obtained, are: Second Frontier, five wells in two fields; Newcastle, six wells in one field; Tensleep, two wells in two fields; and Lower Muddy, five wells in one field. EXPERIMENTAL METHODS AND PROCEDURES Water-displacement data were obtained by the semipermeable barrier method," using both fresh water and brines having either 16,500 ppm sodium chloride or calcium chloride. A displacement pressure of 35 psi was found to be sufficient to obtain the practical irreducible water or brine saturation (IWS, IBS) in most samples. Mercury-injection data were ob-tained with equipment and pro-cedures similar to those described by Purcell.7 Exceedingly high pressures are required to attain complete mercury saturation by this method; however, since saturations in most samples change very little with large pressure increases above 1,000 psia, the maximum pressure used was 1,400 psia. To facilitate comparison of mercury-injection and water-displacement results, it is convenient to express mercury-injection data in terms of unsaturated pore volume. The abbreviation, (100 - SHg)min, is used to denote the pore volume unsaturated by mercury at 1,400 psia injection pressure. Gas permeabilities, ki, were deter-mined by the method proposed by Klinkenberg.8 Methods of determining types and amounts of clay minerals by X-ray diffraction analyses, as well as methods of determining water permeability, have been described previously.' The imbibition characteristics of

Jan 1, 1958

By Petter Östberg

Having brought with me to this meeting a couple of "Mitis'' wrought-iron castings, I have found that they attracted a great deal of attention from steel manufacturers, and especially from those experienced in making castings, among whom some have said that they felt inclined to "unhesitatingly dcclare their manufacture an impossibility," if they had not seen the samples. The consequent demand for explanation of the method of manufacture has been SO great that I accept with pleasure the request by the President to address the meeting on the subject. My object in this address shall be only to explain the main features of the manufacture, referring those who take more interest in the matter to Mr. Th. Nordenfelt's paper, read before the British Iron and Steel Institute, reprinted in many American papers, and containing both a historical sketch of the inventions and many interesting details. As the manufacture of castings from steel by others is, at least to some extent, a success, I shall, in my explanations hereafter, refer to wronght-iron, although our mode of manufacture is equally applicable, with corresponding advantage, to steel of any temper. The successful manufacture of castings depends upon several very important matters, besides the necessary skill of the workman. You must have a suitable metal as raw material; you must have an eacient and suitable furnace for smelting, so as not to injure the metal; you must be able to handle the metal in a suitable way, from the time it is ready in the furnace until it is poured into the moulds; you must have a suitable moulding material. I claim that in every one of these different branches we have made great

Jan 1, 1886

W. P. Blake, Shullsburg, Wis.: I desire to express my admiration of Prof. Posepny's memoir, and particularly of the charming manner and spirit of the introduction. With respect to his mention of the ore-deposits of Missouri and Wisconsin, reference may be made to my paper presented at this meeting (Trans., xxii., 621)) showing the existence of dislocations and breaks in the bedding, and their apparent close relation with the localization of the ore-deposits as claimed by Dr. James G. Percival, and also so claimed by Dr. Jenney in his paper before us (Trans., xxii., 171). I have in my paper given reasons for believing that the zinc- and lead-ores in the strata above the compact Trenton limestones were formed by lateral secretion and concentration from above downwards, substantially as shown by Prof. J. D. Whitney, and not by the ascent of solutions through the fissures, as Prof. Posepny (p. 304) seems inclined to believe. In regard to the contemporaneity of the ore and the rocks, and in favor of a later introduction of ore through fault-fissures, Prof. Posepny (p. 310) cites the influence of these fissures. In my paper, already referred to, I have endeavored to show how faults may have influenced the deposition of ore without being themselves channels for the flow of mineral solutions, and how they may have caused the contemporaneous formation of metallic sulphides from sea-water in the body of a forming rock; the faulting fissure being formed at an early period in the foundation rocks, and probably continuing to be a plane of break and movement in the deposits of later formation.

Jan 1, 1894

By L. D. Jaffe

IN 1945-1946, the author measured temper brittle-ness in ingots of varying composition prepared by remelting SAE 3135 bar stock under vacuum. Since other investigators1-" have been referring to this hitherto unpublished work, belated publication seems worthwhile. Steel in 7 lb batches&apos; was induction melted with nickel additions in a magnesia crucible under a pressure of 10 microns of Hg or less and cast into a 2 in. diam chill mold. The compositions of ingots A, B, and C prepared in this way are shown in Table I; the vacuum melting lowered carbon, manganese, sulphur, and nitrogen content. Ingot B was homogenized 24 hr at 1095°C; ingots A and C were not homogenized. Blanks, M in. square, were cut from each ingot, austenitized 1 hr at 870°C, water quenched, tempered 1 hr at 595"C, and water quenched. Half the blanks from each ingot were given an embrittling treatment of 50 hr at 455°C and water quenched. A few specimens, embrittled and unembrittled, were finally heated 1 hr at 580°C and water quenched. Charpy specimens machined from the blanks were V-notched on the side closest to ingot mid-radius and paired as to radial position in the ingot, one of each pair having received the embrittling treatment and the other not. Specimens were broken in a standard impact machine at various temperatures, the same temperature, in general, being used for both bars of a pair. Fig. 1 shows the results. It is evident that temper brittleness, as measured by the increase in temperature of transition from brittle to tough failure introduced by the 455°C treatment, was decreased but not eliminated by reducing carbon to 0.006 pct, manganese to < 0.004 pct, and nitrogen to 0.001 pct. In another study," temper brittleness was apparently eliminated by -reducing carbon to 0.003 pct, with 0.80 pct Mn and 0.0015 pct N (ingot D)." • Analyses given for carbon below 0.02 pct were made by Jensen method; for nitrogen, by Kjehldahl method. Values quoted else-where&apos;-&apos;." for carbon content of ingot C and for nitrogen content of ingot D were obtained by conventional combustlon and by vacuum fusion methods, respectively, and are considered much less accurate. The 580°C final treatment removed previous em-brittlement (ingot B particularly), indicating that this was "reversible embrittlement."" Metallographic examination of ingot C with 1 pct nital etch revealed only ferrite; ingot A had carbide spheroids uniformly distributed in a ferrite matrix. With ethereal picric acid plus zephiran chloride etchant.&apos; no differences between embrittled and un- embrittled specimens of ingots A, B, or C were noted. Fracture of C and D below the transition temperature was predominantly transcrystalline, with traces of intercrystalline, in both embrittled and unembrittled conditions. The corresponding fracture of unembrittled B was mixed transcrystalline and intercrystalline; of embrittled B, predominantly intercrystalline with some transcrystalline areas. . . . Acknowledgment The efforts of J. C. Leschen, formerly of National Research CO~P., in preparing the ingots are acknowledged with thanks.

Jan 1, 1956

Jan 1, 1929

By S. W. Parr, T. E. Layng

The low-temperature carbonization of coal involves the carrying out of the coking process under conditions wherein neither the coal mass nor any of the passageways through which the volatile products pass are heated above 700" or 800" C. For convenience in this discussion, the single number 750" will be used to designate the maximum range. This temperature is not selected arbitrarily; it is the result of certain natural conditions that are inherent in the substances involved. Two of these conditions arc sufficiently pronounced to suggest a line of demarcation at this point as follows: (1) Below 750°, all the heavy hydrocarbons are expelled, which means that, at these lower temperatures, the illuminants, the gases of high calorific value, and the condensible oils are discharged; above 750") there are given off the lean, non-illuminating gases consisting for the most part of hydrogen and marsh gas and having no condensible constituents present. (2) Below 750") there is substantially no secondary decomposition; above 750") the volatile products are readily decomposed, forming tars, naphthalene, free carbon, etc. It is not intended to maintain that no secondary decompositions occur below 750". Many recent studies have demonstrated the practicability, especially in the presence of catalytic substances, of cracking certain of the hydrocarbon compounds; but at these lower temperatures the step is a moderate one, as, for- example, from xylene to toluene or from toluene to an anthracene. These changes are moderate in amount. Not only do the reactions proceed slowly but they are subjected to the decomposing . conditions for only a short time. This is evident when it is recalled that at these initial temperatures the decomposition of the coal is very rapid and, if anywhere near a neutral pressure is maintained, the movement of the evolved gases is lively and reduces, correspondingly, the time for the retention of the gases in the passageways where these milder decomposing conditions exist. It is acknowledged that the maintenance of these temperature conditions at the present time has only an ideal and not a practical status. Actual operations under these conditions, as a? industrial accomplish-

Jan 1, 1920

By Terry E. Perkins, Len Marnewecke

Installation of a relatively simple, low-cost analog mill control system at Amax Lead Co. of Missouri&apos;s Buick concentrator has paid off handsomely. The system, which provides the capability of handling mill circuit upsets and ore changes while maintaining a desired particle size, is expected to generate annually a return on investment of several times its capital cost. In addition, the system stresses simplicity of field instrumentation and control strategy, leading to better operator acceptance and understanding, and its capital cost makes it very attractive for the specific installation when compared to more complex schemes using mass flow measurement and computers for calculating circulating load to infer particle size. This system has the advantage of utilizing an actual measurement for control, rather than a difficult-to-maintain inferred value.

Jan 2, 1978

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired, a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix .2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth.2.3 Mehl and Smith6 have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible, however, to decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smiths have pointed out, that the lamellae delineate the [210] planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By J. A. Pusateri, M. A. Orehoski, N. R. Arant

Plant studies on commercial-size ingots and laboratory experiments with induction furnace heats have demonstrated that the major source of ingot cracks is associated with two conditions arising during top-pouring practice: 1—solidification during pouring, and 2—turbulence created by the impact of the stream. Methods of controlling the two factors were effective in eliminating or significantly reducing ingot cracks. BECAUSE the process of removing surface defects from hot-rolled product is so costly, the steel industry is striving constantly to develop methods of preventing, or at least decreasing, the occurrence of surface defects. Investigations have revealed steel-making and processing variables related to major surface defects, and controlling these variables has led to improvements in surface quality. However, the fundamental causes of major surface defects, such as ingot cracks, have not been determined; consequently such defects persist. At the Research and Development Laboratory of the United States Steel Corp. in Pittsburgh, a seam research program was initiated to determine the fundamental causes of certain major defects. As a part of the program, ingot cracks in killed, finegrained C1020 steel were selected for study. A cost survey indicated that, of the steels produced in sizable tonnages, carbon steels in the range of 0.18 to 0.23 pct C content require the most conditioning. Since this is particularly true of C1020, any im-provement of surface quality that might be effected from the study would be beneficial. Also, since the frequency of ingot cracks is exceedingly high for this grade, the steel would provide an excellent opportunity for a thorough study of the ingot-crack-ing problem. Why steels in this carbon range tend to exhibit more ingot cracks than do other steels was not considered in the investigation; the mechanism of ingot-crack formation was of paramount importance. Also, only the top-pouring practice was considered in the investigation, because this pouring procedure is used more extensively than others. In this study, ingot cracks are defined. as deep surface defects that sometimes are observed in an ingot prior to rolling but usually are observed during the initial stages of rolling on the primary mills. These defects may occur at any angle to the rolling direction but are most prominent in the transverse or nearly transverse direction. The appearance of ingot cracks on the rolled product varies with respect to their angle of formation and with the extent of rolling after their first occurrence. Ingot cracks are also termed "deep seams," "arrowheads," "irregular cracks," and "transverse cracks." Fig. 1 shows ingot cracks in a rolled bloom. This report summarizes: l—the exploratory investigation of commercial-size ingots; 2—the labor-atory investigations related to determining the source of ingot cracks and developing corrective methods; and 3—the plant evaluations of laboratory methods of decreasing ingot cracks. Exploration of lngot Cracks in Commercial Ingots Materials and Experimental Work: At the Du-quesne Works of the United States Steel Corp., five heats of killed, fine-grained C1020 steel were selected for the exploratory phase of the seam-research program. The heats were made by open-hearth practices that are considered most conducive to good surface quality. They were top-poured into 22x25 in. big-end-up hot-topped molds. One as-cast ingot and four other ingots rolled to the following cross-sectional sizes were set aside from each heat: 16x20 in.; 9 1/2x10 in.; 5x5 in.; and 2x2 in. The processing of the heats, from the time of charging in the open hearth furnaces to the end of the rolling operation on the primary mill, was observed carefully and recorded. The cast ingot and the four rolled ingots from each heat were examined for surface defects. The cast ingots were split longitudinally near the vertical center plane to expose the ingot structure beneath badly cracked regions. Also, a series of transverse sections was cut at about 1 in. intervals in a badly cracked area of one ingot. All sections were ground, polished, examined by sulphur printing and deep etching, and photographed. The rolled ingots

Jan 1, 1955