Search Documents

By T. Ueno

Naoshima Smelter & Refinery of Mitsubishi Materials Crop. commissioned a new Mitsubishi continuous copper smelter in May 1991. Process offgas volume of the conventional reverberatory furnace line, one of the previous smelters having been shut down, was very large and thus two acid plants had been operated. It was expected that the offgas volume would, be reduced at the new smelter to about a half of the sum of those from previous two smelters and the sulfur dioxide strength would be increased. So various alternatives were studied to minimize the operation cost. And it was decided to utilize both of the plants with minor modifications by diluting the gas either with air or with dilute gases. The acid plants now receive off gases from the new copper smelter, a sintering machine of a lead smelter and a decomposer of waste acid. The paper discusses plant design, operation, improvements and modifications realized in relation with the retrofitting of the copper smelter.

Jan 1, 1992

By Yingtao Zhang, Shaofeng Du, Yiming Rong, Wenjun Zhao, Gang Wang

"20Cr2Ni4A steel is a kind of high quality steel mainly used for manufacturing high-duty gears in the world. The high-duty gear with good performance must have wear and fatigue resistance properties. In order to get the good properties, the high-duty gear needs a high hardness gear surface and a good hardness gradient along the depth direction. In this paper, the samples were designed and a vacuum carbonitriding process was put forward to improve the surface hardness of parts for 20Cr2Ni4A. The process contained carbonitriding, quenching, cryogenics, and tempering process. The surface hardness and hardness gradient of carbonitrided samples were measured and the good microstructure was gained. The surface hardness is 67.SHRC and the case depth is 1.2mm.IntroductionSteels are widely used in industry, but the fatigue strength and the wear resistance of steel is much low. So the heat treatment process is put forward to improve the mechanical properties of steel. It can be improved by high-energy heat treatment methods for medium-carbon and highcarbon steel. Those methods will not alter the chemistry of the base metal [ 1].For low-carbon steels, carburizing and quenching should be used to improve the steels' mechanical properties, especially the surface properties. Compared with the carburizing, carbonitriding has more advantages, such as a short production cycle, low temperature and small deformation of parts. Carbonitriding is a modified form of gas carburizing, rather than a form of nitriding. The modification consists of introducing ammonia into the gas carburizing atmosphere to add nitrogen to the carburized case as it is being produced. Nascent nitrogen forms at the work surface by the dissociation of ammonia in the furnace atmosphere; the nitrogen diffuses into the steel simultaneously with carbon. Typically, carbonitriding is carried out at a lower temperature and for a shorter time than is gas carburizing, producing a shallower case than is usual in production carburizing [2]. As a material surface strengthening technology, carbonitriding has been widely used in the production [3]. And vacuum carbonitriding process is better than carbonitriding, because the vacuum carbonitriding temperature can be higher than carbonitriding without surface oxidation."

Jan 1, 2014

By W. Murray Small

Nickel plays an important role in determining the properties of many stainless steels and superalloys. Cobalt also contributes significantly to the performance of certain grades of superalloys. A major technical aspect, in which both of these metallic elements are involved, concerns the solubility of nitrogen in these classes of alloys. Beyond certain content limits, dissolved nitrogen may contribute to the deleterious mechanical behavior by these alloys. It is therefore essential to control the level of this element during alloy processing. In this paper, results from several experimental studies have been assembled and are analyzed to describe phenomena related to the individual effects of nickel and cobalt on the solution of nitrogen in several groups of alloys. Both solid and liquid alloy systems are considered. This information may be used as a guide to limit or control the presence of this interstitial element in alloys.

Jan 1, 1993

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By P. C. A. Maia, J Alexandre, F. A. J. Saboya, A. R. G. Azevedo, G. C. Xavier

"This work shows the characterization of clay and the granite waste by-product from the sawing process of the granitic blocks, used as raw material for brick ceramic. Besides, shows the degradation of the ceramic material obtained with different by-product contents in the waste after lab test degradation, is investigated. The clay is obtained from mine use areas of ceramic industry in Campos-RI and the waste is originating from of the area of Cachoeiro-ES, an important center of decorative stone in Brazil. The mixes were made by the addition of 0% up to 10% of the waste in the raw material. After drying and firing up to 900°C, obtained prismatic pieces were considered intact. Physico-mechanical properties were obtained from wet and drying tests in laboratory considering 50 and 150 cycles. The results showed that the use of powder byproduct has a considerably influence on the weathering and strength of the material.IntroductionThe ornamental rocks and coating defines the most promising areas of business in the mineral sector [l]. In this context, the Espirito Santo appears as the main Brazilian state in production and export of ornamental rocks, representing 47% of national production [2] which in tum is one of the economic sectors most representative of this State, due of its transport logistics and port vocation that facilitates the export of such products.It is estimated that the state of Espirito Santo there are approximately 1,200 companies dedicated to the activities of ornamental rock by providing 20,000 direct jobs [ 1]. These mobilize support activities, such as companies that provide machinery, equipment and supplies for industries, including service providers for maintenance.However, the production of rocks produces about 15,000 tons of granite waste/month [3] only in the municipality of Cachoeiro ltapemirim-ES. This is justified by the presence of more than 500 extraction industries, cutting and processing of stone, with about 900 looms, waste generators.According to [4], there is great potential for the use of granite waste in red ceramics introduced for the manufacture of bricks, blocks structural ceramics. and other ceramic products, especially when evaluated on exposure to weathering."

Jan 1, 2014

By Dr. -Ing. Wolfgang Pietsch

Many primary metallurgical wastes are in the sh.-ape of turnings; borings, chips, dusts, and other particuletes. While such. materials can be easily segregated and/or upgraded to yield high quality ?secondary metals with often known composition for easy recirculation into the production? process; their particulate nature results in various problems. Roller presses are used in an ever increasing number for size enlargement and densification of primary particulate metallurgical wastes for secondary metal recycling. The paper will mention the areas of application from A(luminum) to Z(ink), also including Brass; Cast Iron, lead, and Stainless Steel, as well as dusts from all types of melting and ladle furnaces or converters. Typical systems using roller presses for size enlargement. will be discussed.

Jan 1, 1995

By Glenn Stevens

After 40 years of operation with the original design, Pan Pacific Copper determined it was necessary to rebuild the Saganoseki Flash Smelting Furnace to continue safe operation. The original design employed a rigid steel frame, which, through hearth growth, led to severe distortion of the frame. Contributing to the continued growth of the hearth were thermal cycles that occurred during the government mandated annual shutdowns. Hatch designed a unique sprung bound, pivoting binding frame to maximize crucible size within the existing furnace footprint, while integrating the PPC designed cooling jackets. The bound system maintains tight brick joints, while the new conductive hearth design with integrated bottom cooling produces a protective freeze layer to accommodate higher furnace throughput. Minimization of furnace downtime for the rebuild was achieved through effective construction planning, highly trained contractors, and through an efficient start-up and ramp-up to full production.

By F. Kassabji

This publication presents the main experimental and theoretical results on the recovery of aluminum scrap (dross and Used Beverage Can) without use of any addition of fluxing salts. Dross and UBC's processing experiments have been conducted in a rotary plasma furnace operating in the transferred and non-transferred mode, using different plasma gases. The investigation involved the treatment of more than 100 kg of dross and other aluminum residues using plasma torches with less than 100 kW power. The experimental work showed that this process is .far more economical and kind to the environment than the conventional route using a salt flux. An equilibrium thermodynamic calculation at elevated temperature makes possible the prediction of by-products at various temperatures for different plasma gases.

Jan 1, 1994

By M. Frades, C. Frías, G. Díaz, A. B. Mejías

"In recent years, zinc recovery from flue dusts and other industrial wastes has been increased, offering to the market a large tonnage of secondary zinc oxides, which can not be processed directly to render high quality zinc because of the hazardous impurities and halogens content.The ZINCEXTM Technology has been commercially applied for more than thirty years and represents the most suitable solution to deal with secondary or crude zinc oxides due to its flexibility, simplicity, and cost-efficiency, allowing production of SHG electrolytic zinc and pure zinc sulfate salts thanks to the flexibility and selectivity of the zinc solvent extraction unit regarding to get rid of impurities.A dual plant able to produce electrolytic zinc and crystallized zinc sulfate has been engineered to provide a flexible and profitable solution to zinc market. A description of the study and the relevant achievements is presented in this paper.IntroductionZinc is a valuable commodity in the marketplace and can be recycled again and again and still maintain its physical and chemical properties. Zinc recycling offers both environmental and economic benefits such as reducing volumes of material that end up in landfills, saving energy by reducing the need for mining and smelting, and relieving environmental impact on the land and water, and conserving zinc ore [1].The supply of zinc able to be re-processed will be increasing from year to year according to secondary materials enter the recycling stream, and as a result, more recycled zinc will become available in the market. Thus, some existing zinc refineries are implementing an annexed treatment line to process secondary oxides in conjunction with primary zinc concentrates [2].The galvanized steel scrap is normally recycled in electric arc furnaces or in basic oxygen furnaces, which generates a large tonnage of zinc-bearing flue dusts (EAFD). Around one million ton EAFD is yearly produced at the USA and the EU, respectively. The flue dusts are treated commercially by pyrometallurgical ways such as waelz kilns, electrothermic furnaces, etc, to yield secondary zinc oxides that can not be processed directly to render high quality zinc because of the hazardous impurities and halogens content [3]."

Jan 1, 2008

By Shuo Wang, Yu Wang, Bing Xie, Rui Tang, Hong-Yi Li, Kun Wen

"During present converter vanadium extraction process, phosphorus could not be removed from hot metal due to absence of CaO in slag though it is an efficient way for vanadium extraction. In order to improve the phosphorus remove and produce CaO-containing vanadium slag, which could be directly used in subsequent roasting process, during the converter vanadium extraction process, lime dissolution in FeOx-Si02-V203-Ti02 slag was investigated by using a rotating cylinder technique and the slag-lime interface was characterized by SEM/EDS. Results showed that changes in the slag chemistry and phase compositions during the lime dissolution process were similar to that in CaO-Si02-FeOx based slag during the BOF process. The V and Ti in the slag were expected to diffuse into the lattice of2CaO·Si02 solid solution, which formed a rather thinner layer in thickness at the slag-lime interface than that in BOF process, leading to improvement of lime dissolution in the slag.IntroductionVanadium is important material that widely applied in industries. The traditional technique to extract vanadium was to leach vanadium after sodium salt roasting. However, the sodium salt roasting process has several problems including lower yielding rate[!] and environmental pollution[2]. Therefore, the more environment-friendly technique of calcium roasting[3-4] was proposed. In order to increase roasting efficiency of vanadium slag, it is essential to study the dissolution/reaction mechanism between lime and vanadium slag. Many investigations about the dissolution reaction of lime in molten slag have been carried out from the standpoints of rapid slagging to De-Pin steelmaking process[5-6]. However, their studies were focused on BOF slag and the reaction mechanism between solid lime and slag containing vanadium has not been reported yet. In present work, the dissolution process was studied with rotating cylinder technique and the reaction interfaces were observed and analyzed by SEM/EDS to elucidate the dissolution mechanism of lime in vanadium slag. This work was supported by National Natural Science Foundation of China No. 51090382."

Jan 1, 2013

By Sudhir C. Dhara

An attempt has been made on the concentration of Platinum Group Metals (PGM) from the converter matte material by microbial .leaching. Biological oxidation of base metal sulfides such as iron, copper, nickel and free sulfur present in the matte material using Thiobacillus ferrooxidans is an alternative method to concentrate the PGM-and gold. The method which produces a platinum group metals concentrate is comparable to chemical processes and electrochemical process.

Jan 1, 1995

By Xiping Chen, Wangxing Li, Jiemi Zhou

"Desulfurization methods suitable for anode-grade petroleum coke (coke for short) used in primary aluminum industry are coke desulfurization during calcination, desulfurization in soakage and desulfurization in mediums. Coke desulfurization during calcination is discussed in this paper. Influences of calcination temperature, holding time and coke granularity on coke desulfurization were discussed. Experimental results show that calcination temperature has a remarkable influence on coke desulfurization. When the temperature is high enough desulfurization ratio of coke can reach 85% only by calcination. Holding time has a definite influence on coke desulfurization, but desulfurization ratio is low at the temperature of 900~1300°C. The influence of holding time is obvious when calcination temperature surpasses 1400°C. The influence of coke granularity is smaller compared with calcination temperature and holding time.IntroductionPetroleum coke is main raw material for carbon anode in primary aluminum industry, and its weight percentage in carbon anode is about seven percent. Green coke can not be directly used for anode production because of its immanent moisture and volatiles. Green coke must be calcined in order to meet the request of anode production. Calcination is a heat-treatment process during which green coke is heated to a given temperature to remove volatiles, moisture and some sulfur. Real density, strength, electrical conductivity and anti-oxidation ability of petroleum coke can be improved by calcination and calcined coke can be received [1, 3, 4]. Sulfur in calcined coke finally goes into carbon anode. During baking or aluminum smelting, the sulfur in anode ultimately changes into SO2 and emits from anode into the atmosphere. Excess SO2 easily leads to acid rain which brings heavy pollution to the environment [1, 2]. With the development of Chinese aluminum industry, consumption of anode-grade petroleum coke increases year by year, the total consumption in 2007 surpassed 4.5 million tones and the yearly emission of SO2 from aluminum smelters has exceeded 270 kilotones. From 2005 Chinese government began to limit the emission of SO2 from primary aluminum industry, so desulfurization of anode-grade petroleum coke becomes more and more urgent. Some relationship need to be found and used to guide desulfurization of petroleum coke."

Jan 1, 2008

By Robert H. Hsu

Palladium finely dispersed in a substrate of kieselguhr, Pd/k for short, has been successfully used for hydrogen storage, separation and pumping for a number of years at the Savannah River Site (SRS). Recently SRS has developed a new pd/k flow through bed (FTB) prototype for separating hydrogen from other gases and simultaneously storing the hydrogen on palladium. The FTB uses single-pass liquid nitrogen cooling during hydrogen absorption/separation/storage and electrical heating for desorption/unloading of hydrogen. Fourteen absorption-desorption or loading/unloading cycles using hydrogen have been conducted with the new FTB prototype. Test results show that all design performance objectives have been successfully achieved: recover 295% of hydrogen gas from feed gas, produce 99.9% hydrogen product gas and < 5% hydrogen in discharge gas. This paper will discuss characteristics of the palladium-coated kieselguhr or diatomaceous earth, design and operation of the FTB, and results of performance tests such as separation efficiency, hydrogen storage capacity and system heat transfer characteristics.

Jan 1, 2002

By Yang Guangqing, Shao Jiugang, Zhang Jianliang, Wan Dan, Fu Yuandi, Guo Hongwei

"Resource of metallurgical coke is becoming scarce, and although coke can be partially replaced by pulverized coal injection, there are many restrictions for further increase in coal ratio. Mixed charge of ore and lump coal from top to replace more coke was studied in this paper. Softening-melting property of the burden was affected by charge of lump coal. Softening-melting properties of mixed charge of ore and coke, mixed charge of ore and lump coal were tested respectively. Results show: the property of the burden mixed with coke is superior to the burden mixed with lump coal; lump coal would not deteriorate softening-melting property of the burden and some of them can even improve softening-melting property of the burden. Top charge of lump coal would not deteriorate softening-melting process, and this should be a new way to increase coal consumption to decrease coke rate.IntroductionThe blast furnace is still the predominant process for the reduction of iron ore and will probably remain so for the next decades. Metallurgical coke is becoming scarce and expensive, so the cost of hot metal can be decreased by reducing the consumption of metallurgical coke[l]. Coke can be partially replaced by pulverized coal injection, currently the highest rate of pulverized coal reached 266kg/tHM, most of blast furnace PCR is about 150kg/tHM, and it is very difficult to further increase of PCR. Nut coke is charged into blast furnace mixed with iron ore, not only for improving utilization of metallurgical coke, but also for lowering the coke rate. Presently the majority of blast furnaces in the world use nut coke although its amount is very different: from 10-20 to 70--100 kg/tHM and more[2-4].The effect ofnut coke in blast furnace is extensively researched, and the main conclusions recommend: to improve gas permeability of cohesive layer in blast furnace, to promote reduction of iron burden, protect metallurgical coke from the solution in the shaft due to higher reactivity of nut coke. There is no special requirement for the strength of nut coke[5-8]. Nut coke is also used for sintering fuel, which may lead to the shortage of the nut coke charging into blast furnace. So lump coal mixed with iron ore is considered to be charged into the blast furnace, not only to reduce the cost of grinding coal, but also to increase the use amount of coal."

Jan 1, 2013

By William Petruk

A mineralogical and image analysis study was conducted on samples of U tailings from pilot-plant runs on Midwest ore in Northern Saskatchewan. The tailings had been subjected to simulated weathering for the equivalent of 10 years in a tailings facility (lysimeter). The pH varied from 7.0 at the beginning of the test to 5.9 at the end. The results show that during the simulated weathering sane of the gersdorffite, uraninite, galena and pyrite had oxidized, with gersdorffite being the most reactive and pyrite the least. Reaction was evident at the top of the lysilleter , but was most intense at the seepage discharge. sane of the released ions precipitated as Ni, Pb, and U arsenates, sulfarsenates, sulfates and oxides on particles of all minerals. Green crystals of Ni sulfate and white crystals of ca sulfate had precipitated at the surface of the lysilleter. Clay minerals and chlorite had washed from the top of the lysirneter towards the seepage discharge.

Jan 1, 1989

By SenYang Qian, ShuangYu Du, Bo Wang, Jieyu Zhang, Jian Zhao

During the solidification process, the flow pattern of the molten steel has significant influence on the formation of solidification microstructure. In present study, the solidification microstructure of 30Cr2Ni4MoV steel ingot under different intensities of mechanical oscillation(forced convection) was simulated by using ProCAST®software. The results showed that the increase of the intensity of oscillation could restrain the development of the columnar grains and refine the grains. As the intensity of oscillation increased, the proportion of columnar grains decreased and the proportion of equiaxed grains increased. When the intensity of oscillation was at a low level, the effect of refining grains could be improved obviously by increasing the intensity. However, as the intensity increased to over 0.833, the effect of refining grains would not be improved.

Jan 1, 2016

By Alexander V. Suvorin, Vladyslav M. Sokolov

"The traditional technologies for production of the coprecipitated and deposited catalysts are analyzed from the standpoint of diversion of application of the feedstock and increase of efficiency for its usage. The options for return of the metals of spent catalysts to the catalysts production are described. The novel environmentally friendly and cost efficient approach for reutilization of the spent catalysts is realized in practice. It anticipates application along with spent catalysts of the waste generated in the catalytic productions. Reutilization of the Ni-containing catalysts is referred as an illustration. Introduction The recent development of large catalytic manufacturing for organic and inorganic synthesis, and petroleum refinery as well as for applied environmental catalysis has brought about increase and diversification of catalysts production. The generation of spent catalysts has been increased correspondently. The feedstock for production of catalysts is mostly metals in a form of nitrates, carbonates, hydroxides, hydroxydcarbonates. Sometimes salts of organic acids, of ammoniates, of chlorides and of sulphates occur. All these materials are scarce and expensive. So their repeated use by reutilization of spent catalysts is very actual issue. The traditional recycling the Fe-, Cr-, Ni-, Cu- or Zn-containing spent catalysts are carried out by pyrometallurgical reclamation of pure metals or alloys. They can not be used directly in production of catalysts [1, 2]. The hydrometallurgical approach is used for recycling spent catalysts with PGM, W, Mo, Co, Ni or Cu. It provides production of salts of these metals in a form of sulphates, chlorides, carbonates, hydroxydcarbonates and sometimes nitrates or ammoniates. Only a limited number of these salts can be used directly in production of catalysts. Material losses during catalysts production The basic feedstock for manufacturing coprecipitated and deposited catalysts that may be produced from the spent catalysts is aqueous solutions of metals nitrates. Their production is based on application of nitric acid as a dissolvent. About half of it is lost with the flue gases in a form of nitrates vapor and nitrogen oxides (II, IV). The last compound is generated by reaction:"

Jan 1, 2008

By A. Alvarez

In this work, mesophilic and thermophilic cultures have been used in the presence of silver as a catalyst. Chalcopyrite and byproducts of bioleaching were characterized in order to: a) obtain information about the kinetics control of the process, and b) explain the different behaviour observed during the mineral attack. With thermophilic microorganisms (68°C and Norris medium as nutrient) the reaction stopped at approximately 65% copper extraction, with and without Ag ion addition as a catalyst. The remaining chalcopyrite appears surrounded by hydronium jarosite (with ammonium ion in substitution in the "alkaline site"), goethite and elemental sulphur. With mesophilic cultures (35°C and 9K medium as nutrient) the reaction stopped at approximately 25% copper extraction (without Ag) and approximately. 85% extraction (with Ag). In both cases, the remaining chalcopyrite was surrounded by agglomerates of ammonium jarosite (with hydronium ion substitution in the "alkaline site") and some iron oxides and/or hydroxides.

Jan 1, 1999

By Pavol Loderer

Mineral froth pumping utilising centrifugal slurry pumps is a major engineering challenge for the end users and pump manufacturers due to the undesirable outcome of unstable pump performance. Most of these challenges occur due to incorrect pump selection and suction tank design. The traditional approach is to oversize the pump for pumping mineral froth. New horizontal slurry froth pump designs offer opportunities to improve the mineral froth with challenging (high) Froth Volume Factor while maintaining high efficiency, long wear life and stable pumping performance. This paper examines the flotation process in detail and how froth pumps are designed to handle this arduous process.

By Vianey Garcia-Osorio

One of the problems in the carbothermic aluminum process is the substantial loss of aluminum compounds as vapors due to the high temperatures in the process. In order to solve this problem a Vapor Recovery Unit (VRU) is proposed. In this unit operation the aluminum vapor undergoes a series of heterogeneous non-catalytic reactions forming solid, liquid and gas products. In this work a model for the simulation of this unit was developed which includes heat and material balances as well as heterogeneous non-catalytic reactions. The model leads to a system of differential equations; its solution was implemented in Matlab giving as a result a stage-by- stage solid-fluid reaction model.

Jan 1, 2001