Search Documents

By Peter Deming

"PART 2 OF 2 (CONTINUED FROM SUMMER 2006 EDITION) CONSTRUCTION ISSUES (cont’d) The Influence of Ground Conditions on Collapse Sand and gravel strata provide frictional resistance to support active earth pressure. The angle of internal friction has only slight influence on computed stability. Sand and gravel material design parameters can be defined with SPT N-values. Silt strata should be analyzed using internal friction. Definition of soil parameters should be performed by laboratory testing. Cohesive materials, especially soft clay and peat, require careful definition for design. Shear strength should be determined by laboratory testing. Work platforms constructed over granular strata improve the ground resistance by increasing confining pressure. However, temporarily increasing overburden stress on cohesive ground reduces trench stability. If the ground contains soft cohesive deposits which are not normally consolidated to the construction overburden, these must be stabilized before attempting trench construction. Use of wick drains and surcharge fill to improve the ground is recommended. Ground stabilization work requires time, and should be performed by the Owner prior to trench excavation. The addition of cement, stone columns, or other measures to support trench excavation equipment is typically determined to be more expensive and less dependable than ground improvement. Excavation through peat can be especially problematic. Peat materials rapidly compress when earth pressures exceed preconsolidation stresses. Backfill materials provide a horizontal stress on the trench wall which can exceed the bearing capacity of peat. As the peat compresses, the trench becomes wider, and slurry levels drop and trench stability can rapidly deteriorate. If the peat is the closure layer, a shallow key is recommended. If peat is present on the trench wall, preconsolidation with surcharge is recommended. Bottom preparation and Backfill Placement Trench wall stability is a temporary condition which must be controlled by proper design and construction of work platforms and slurry features which influence ground support. Backfill materials and intimate contact of the backfill with the closure layer are permanent conditions which are the end goal of the work. The most common reason slurry trenches fail to provide working barriers is improper bottom closure. Either the closure layer is not engaged, or the backfill is not in intimate contact with the closure layer. This can result from construction problems associated with sidewall collapse described above, slurry performance and/or degradation, backfill placement methods, and failure to maintain the trench bottom clear of sediment prior to placing backfill."

Jan 1, 2006

By Frank Rausche

Although Quality Control (QC) during construction is preferable for deep foundations, there are many instances when it is necessary to resort to Quality Assurance (QA) methods if, for various reasons, QC is not possible. Non Destructive Testing (NDT) methods for deep foundations are indirect approaches, i.e. in complex situations they do not provide complete information and need to be augmented by additional testing and/or analyses. While the challenges are varied for the different deep foundation types and the different test methods they are the same in many different countries. Experience of the tester is often mentioned as being most important for a successful quality assurance. In addition, reliable testing equipment for the best possible measurements and complete construction documentation for a meaningful data interpretation are minimum requirements for a successful test outcome. Another problem is the widely varying cost of the QA tests. For that reason the specifying engineer or authority has to be aware of what can reasonably be expected so that technically feasible specifications can be written for optimal cost and minimal construction delays. This paper discusses the most common NDT methods with a view on how these methods are applied world wide. It summarizes features of specifications, recommendations for test procedures and advanced analysis methods which can help to overcome uncertainty in the quality assessment of the foundation. Finally, the authors propose a decision tree for various QA methods, deep foundation types and soil properties.

Jan 1, 2008

By James Warner

Although use of low mobility grout is just now beginning in some parts of the world, its advantage for many applications has been well established through more than 50 years of positive experience. The single largest area of application continues to be densification of soil by way of compaction grouting. Because it is often the safest and least costly method for soil improvement in general, and virtually always that in connection with soil improvement under, or adjacent to structures or in developed areas, use will undoubtedly increase both geographically and in diversity of application.

Feb 10, 2003

By Vladimir M. Korolev

The field studies conducted at the experimental-production sites allowed to develop the technology of arranging drilling piles in loess subsiding grounds over 25 m deep and over 250 mm in diameter, to select optimal compositions of flush fluids, to assess the carrying capacity and field of use of the piles under test and to produce a special equipment. The dependence of the ultimate axial pressing-in load on pile driving into the non-subsiding section, its diameter and method of fulfillment, as well as the ground moisture dependence of the specific ground resistance along the piles' side surface within the limits of the subsiding section were determined. The study results allowed to reduce the length of the work piles and the number of bars in the reinforcement frames. The obtained experimental data enable to give a preliminary assessment of the piles' carrying capacity under complicated engineering-geological conditions of subsiding grounds.

Jan 1, 2002

By T. Matsui

Many existing bridge abutments on the soft ground laterally move and their many damage examples have been reported. An essential cause for the troubles of the lateral movements may be the lack of examinations for the lateral earth pressure acting on its foundation piles. In the present paper, actual movement condition of existing bridge abutments is first summarized, and then the author establishes a practical and systematical design method for bridge abutment foundation piles, including the examination for the passive pile.

Jan 1, 2010

By Kanagarajah Ravishankar

Drilled shaft (caisson) foundations are extensively used in the past. In the central part of New Jersey, the soils consist of silt and clayey silt overlying Triassic age shale bedrock. The shale is friable and generally severely weathered and highly fractured. The shale crumbles readily into small fragments. In general, the shale is encountered in shallow depth. Subsurface investigations indicated that the upper part of the shale is very soft, highly weathered, and able to advance through soil exploration methods. The underlain formation is relatively hard and required rock coring techniques for sapling. Individual core recoveries ranged from 10 to 100 percent and Rock Quality Designations (RQD) vary from 0 to 90 percent. Although several methods available to estimate the axial capacity of drilled shafts, it is a difficult task for the designer choose the suitable method due to self disintegrate nature of the shale. In the recent years several bridge foundations have been constructed using drilled shafts founded on shale rock in the vicinity of the central New Jersey. Based on load tests carried out on drilled shafts during construction, subsurface exploration, and laboratory tests, suitable methods for determining axial capacity of drilled shafts is analyzed. This paper presents the findings of the field tests and suitable methods to determine the axial capacity of drilled shaft founded on soft shale. Key words: Drilled shaft, axial capacity, Osterberg load test, shale.

Jan 1, 2006

By Dinesh R. Katti

Caissons which are locally known as well foundations, which may very in diameter from 30 m to more than 30 m and in majority of the cases having depth to diameter ratio between 1 to 1.5, are normally used to support piers of long span bridges or tall structures, which transmit high magnitude of axial load, horizontal thrust and moment. On the basis of depth to diameter ratio the foundation system appears to fall in the category of shallow foundations but due to deep excavation, it is observed that part of the moment acting on the caisson is shared by due the sides due to development of passive resistance. The problem is statically indeterminate and three dimensional in nature. To ascertain the various parameters needed for design, such as moment shared by base and sides, horizontal and vertical displacement and tilt, and base and side contact pressure diagrams need to be obtained from nondimensional relations of parameters with respect to D/B ratio derived from large scale model studies conducted by Katti etal at IIT, Bombay under MOT Project between 1976 and 1988 and later on at UNEECS. On the basis of above data on attempt is made to put forward guide lines for selection of parameters for design of caisson foundations / well for following cases for opening us some discussion. The cases are cohesive soil at the side and cohesive soil, or sand or soft rock or hard rock at the base.

Jan 1, 1996

With respect to liability damages, claims and costs thereof relating to or ansmg out of contamination, special or non-special wastes, hazardous wastes or pollution in connection with the performance of this subcontract: It is understood that the subcontractor's work and responsibility wholly exclude any requirement to handle such contaminants or to otherwise be responsible for such contaminants, and Subcontractor shall not be nor be considered to be a generator of such contaminants. Contractor shall indemnify, defend and save harmless Subcontractor and its sureties, from and against all liability, damages, claims and costs relating to or arising out of contamination, special or non-special wastes, hazardous wastes

By Ross Cutts

As a public servant geotechnical engineer, I observed how costly and valuable geotechnical field explorations are to the success of every project. Often however, the field exploration is a long and complex process that is made less efficient by the difficulty of retrieving and utilizing nearby internal or external historic geotechnical datasets. As an employee of a public agency, we would often start our investigations for every project from scratch, given the difficulty of locating and utilizing historic geotechnical data. This is an ethical and technical failing of our profession. When we start subsurface explorations from scratch, not only do we often duplicate investigations, we are also likely defaulting to reapplying tradi- tional test methods that yield con- servative geotechnical parameters, resulting in overly conservative and potentially costly construction. To address this issue while working as a public servant, I started a research program with Yunfeng Zhang, Ph.D., of the University of Maryland, to build a tool that could compile internal historic geotechnical data and extract additional value from it, using machine learning. This tool was able to provide, upon request, nearby historic geotechnical data, estimated soil parameters and recommendations for geotechnical test methods best suited for a given project site. This prevented common field ex- ploration problems such as, requesting duplicate data, requesting test methods that were not applicable for the project geology, not realizing presence of karsts, missing permits for wetlands, private property and others. This tool allowed for more efficient field investigations with regards to time and money saved. There was one problem with this tool: it could only be used by internal employees of a single state's depart- ment of transportation (DOT) for which this data was compiled. I realized at that point that it would be of tremendous value to make this concept universally accessible to the geotechnical engi- neering profession. I left public service to devote time to building a platform that would host historic geotechnical data from publicly funded sources throughout the country. The tool I helped build as a public servant was the foundation of Geosetta, a nonprofit company dedicated to serving the geotechnical profession. The nonprofit structure was adopted to prevent acquisition by a for-profit company and to ensure that Geosetta remains an independent steward of our profession's valuable data. Geosetta provides a GIS (geographic information system) platform that enables users to view historic geo- technical data and extract value from it with machine learning-based predictions and visualization tools. This data is provided in an open and interchangeable format called DIGGS, which stands for Data Interchange for Geotechnical and Geoenvironmental Specialists, making it easy for users to integrate it into their workflows. Geosetta is collaborating with the American Society of Civil Engineers' Geo-Institute and other sponsors to extract public data at no cost to the agency and provide the profession with free access to the existing data and access to advanced tools through a subscription to support the nonprofit mission.

Nov 1, 2023

By Wang Mingshu

The pile foundation is a kind of advanced foundations in the filled or soft soil. In this paper, through the actural engineering of coal dressing plant of Western Opencast Coal in Fushun built on the mining dump with large diameter pile foundation, the construction method and mechanics analysis of pile are given. Unless it is in following stadge, the stability of pile cannot be lost due to its small rigidity. The analysis shows that pile foundations of large diameter ellipse section can decreased hotizontal displacement to 60% ?70% of that of equal section an in the design of a single pile and a single column, the ellipse pile and manual dig hole are most favourable. So a large amount of concrete can be saved.

Jan 1, 1991

By Cornelis Van Der Veen

Foundation piles, partly passing through unconsolidated compressible layers, suffer a downward drag that is called negative skin friction. The negative skin friction depends on the movement of the surrounding unconsolidated soil relative to the pile and on the friction between pile and soil as a function of that movement. The negative skin friction adds to the load on the pile. However as it is a function of the pile movement relative to the soil, the amount of negative skin friction to be taken into account to determine the allowable bearing capacity depends on the allowable pile settlement. In this paper this property is indicated by the factor µ. As under the conditions of ultimate pile bearing capacity negative skin friction does not occur, a factor of safety is introduced, which is lower than normal. Eventually a formula for the bearing capacity is given in which µ and both figure. The exact values for given circumstances have to be determined empirically. A few examples are given.

Jan 1, 2010

By Bengt H. Fellenius

An upgrading and straightening of a highway included building a bridge across a small river. A routine site investigation was initiated to determine the conditions for designing the foundation of the bridge. The proposed bridge was a two-lane highway bridge in one span with a total length of 30 m (100 ft), as indicated in Fig. 1. It was to be placed about 20 m (66 ft) upstreams of the bridge for the existing highway. The site investigation included one boring at each abutment with soil sampling and in-situ vane testing and placed about halfway up the slope from the small river at ground surface elevation + 54 m. Within the investigated maximum depth of 40 m (130 ft), the soils at both borehole locations consisted of a thin clay crust over a thick deposit of soft sensitive clay with a natural water content of about 70 % and a liquid limit of about 60. The undrained shear strength below the crust was about 20 KPa (400 psf) and increased slightly with depth. The sensitivity was high, about 40.

Jan 1, 1987

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By J. K. Mitchell

Soil improvement is examined within the context of the characteristics of different soil types, the types of ground improvement techniques that can be used to improve them, and the level of improvements that might be achieved. Several case histories are described to show how the particular soil and foundation characteristics influence the choice and success of different ground improvement techniques. Although the basic methods for soil improvement have been known for many centuries, there have been significant recent advances in the technology for their use. Time effects following the densification of cohesionless soils may lead to significant improvements in strength and stiffness. Unanticipated chemical reactions may follow stabilization using admixtures when soils for which there has been little prior experience are encountered. In some cases foundations that combine features of both ground improvement and deep foundation systems may provide good performance at reasonable cost.

Jan 1, 2010

By Thomas Kennedy, Michael Bennett

"History never repeats itself, but it often rhymes." The old aphorism reflects how the study of the past may, perhaps, be most widely valued when it can be used to improve current and future decision making. The education the authors received as geotechnical graduate students certainly impressed upon them the importance of recognizing that not all wisdom is necessarily new. Much of their graduate coursework involved reading technical papers that had introduced concepts of outstanding historical significance in the field, such as pore pressure coefficients, stress paths, and the stress history and nor- malized soil engineering model. These papers gave the authors both respect for and interest in the historical develop- ment of the field. After graduation, the authors furthered and deepened this interest by continuing to expand their knowledge of the profession through both experience in practice and the review of additional literature.

Jan 1, 2023

By Richard Schmidt, Lijun Deng, Mohamed Abdelaziz, Weidong Li

Helical piles are widely used as a foundation supporting a variety of different structures. Understanding the axial behaviour of helical piles is required to confirm the engineering design. Helical pile research is often conducted in the field, but this method can be prohibitively expensive in some cases. Geotechnical centrifuge modeling offers an alternative method for the helical pile research and practice. A series of axial load tests of helical piles installed into cohesive soils were conducted on the geotechnical centrifuge at the University of Alberta. The objective was to investigate the effects of inter-helix spacing and soil strength on the axial behaviour of helical piles. Four types of aluminum model helical piles including one single-helix pile and three double-helix piles with various inter-helix spacing ratios were tested. Both compressive and tensile loading tests were conducted. All model piles were instrumented with multiple strain gauge stations. The clay had an undrained shear strength of approximately 50 kPa and 120 kPa. The test results indicate that there is a transitional failure mode between the two widely recognized failure modes, i.e., individual plate bearing and cylindrical shearing. The shaft adhesion was significantly reduced by the helix. Axial capacities were comparable to the field test results.

By Junho Lee, Leopoldo Bello, Mohammad Khan

Multiline ring anchor (MRA) was developed as a cost-effective solution for securing floating offshore wind turbines (FOWTs) to the seabed. Since FOWTs are placed in arrays compared to conventional oilgas platforms, the availability of multiple mooring lines attached to a single anchor can make FOWTs economically competitive. Additionally, the MRA can provide a small and light-weight anchor with high resistance to mooring line loads due to its deep embedment depth. The combined benefits of fewer and smaller anchors allow substantial reductions in anchor material, transport, and installation costs. Such cost reductions are critical to reducing foundation costs for the wind turbine, which can comprise well over 25% of the capital costs for offshore wind power development. Since it substantially reduces the required number of anchor footprints, the multiline anchor concept also permits significant reductions in seabed site characterization costs. This study evaluates how potential advantages of the MRA can reduce the capital costs and provide a reliable cost analysis of the foundation component for offshore wind farms.

By Ting-Wei Wang, Yung-Wen Chen

Artificial ground freezing is commonly used globally during excavation of shield tunnels and for groundwater control. It is a special construction method for temporary ground improvement that involves introducing coolant into underground pipes to freeze water in the soil. The frozen soil is cemented together as a result to form a frozen wall, which provides high strength and low permeability. Once the thickness of the ice wall reaches design requirements, underground excavation can be conducted with the coolant removed afterward to return the soil to its original state. This technique is cost-effective in scenarios where complete groundwater cut-off and excavation support are required; where work is deep underground and faces difficult ground conditions and where access restrictions limit the use of other displacement-type ground improvement techniques. Due to the demand for shield tunnel construction for utilities in Taiwan, ground freezing has become an important soil stabilization method there. In this article, we will share two brine freezing case studies and an in situ liquid nitrogen experiment that was conducted to develop this technique.

Feb 1, 2022

By R. L. Wei

The disturbing influences of pile driving on the surrounding soil mass, including the induced vibration, pore pressure and displacement of soil, were observed during the construction of pile foundations. It is shown that the effects of pile driving in saturated soft clay are tremendous and ought to be concerned attentively.

Jan 1, 2010

By Jacob A. Jordan, Rachel M. Garrett, W. Robert Thompson III, James C. Pegues

"Environmental control structures for an existing fossil-fuel power generating plant near Pascagoula, Mississippi faced several design and construction challenges due to space limitations. Conceptual design calculations indicated drilled shaft foundations would likely be needed to accommodate the higher lateral and compressive loads expected under some structures. A maximum drilled shaft diameter of 60-in was preferred due to various space constraints. Smaller diameter drilled shafts were deemed acceptable under structures with more moderate loading conditions. Furthermore, augercast piles were considered where lateral loading was not a governing design criterion.A series of SPT borings and CPT soundings revealed a subsurface profile consisting of soft to firm clays to depths of about 25 feet, underlain by fine to coarse sands. The apparent relative density of the sands was loose just below the clay, with increasing density noted with an increase in depth.Analysis of conventional drilled shafts indicated needed capacities could not be achieved unless shaft lengths exceeded 100 feet. Post-grouted drilled shafts were therefore evaluated to decrease shaft lengths by taking advantage of increased base capacity. Analyses showed the higher predicted capacities needed for some structures could be achieved with this approach. Final design for the project incorporated 90-ft long, 60-in diameter post-grouted drilled shafts; 60-ft long, 48-in diameter post-grouted drilled shafts; and 60-ft long, 48-in diameter conventional shafts. Both post-grouted and conventional trial shafts were installed as part of the detailed design phase of the project. Each trial shaft included CSL integrity testing and Osterberg-cell bi-directional load testing. Load test results revealed that additional base capacity was, in fact, achieved through the post grouting process. The 60-in diameter post-grouted production shafts and the 48-in diameter conventional production shafts have been installed at the site, with the project that would utilize the 48-in diameter post-grouted shafts deferred at this time."

Jan 1, 2015