Search Documents

By Blair J. R

In the Bayer process, bauxite is leached with caustic soda, forming a solution of sodium aluminate, from which hydrated alumina is precipitated. The efficient operation of the continuous form of this process requires that the concentration of caustic soda be controlled. A computer simulation of the concentration of caustic soda has been conducted to provide information, regarding the dynamic behaviour of caustic concentration, which is not available from normal plant data. The basis of the simulation is a state- space model of an alumina refinery, linearized about the normal operating condition. The formulation of the model, with the relevant approximations and assumptions, is outlined. The simulation of the mudwash section of the. plant is described in detail. A continuous model of the mudwash, having time-varying coefficients, was driven using operating data from an alumina refinery. The modelled response showed reasonable agreement with the recorded plant response.

Jan 1, 1977

By Williams DJ, Battino S

The rapid crushing technique for the measurement of gas content of coal consists of accelerating the rate of gas desorption from coal by crushing. This technique allows the determination of gas content in the space of hours rather than days or weeks as required for the traditional slow desorption technique. The crushing technique is used particularly when gas content determinations are urgently required for mine safety purposes. The method is now routinely used in underground coal mines of NSW and to a lesser extent in QLD. Despite the rapidity and efficiency of this method, concerns have been raised upon the reliability of the method to deliver accurate results. Experience in Australia has shown that there is in fact some discrepancy in results between gas laboratories using the rapid crush technique. The development of rapid crushing techniques for seam gas content measurements in Australia and the main causes of variability in the gas content test results were investigated. The gas laboratories participating in the gas content testing were CSIRO Division of Coal and Energy, BHP Technical Services and GeoGas Pty. Ltd.

Jan 1, 1998

By R Balusu

This paper provides an overview of computational fluid dynamics (CFD) modelling capability developed by CSIRO with the aim of improving the knowledge of flow migration dynamics within longwall goaf areas. The CFD models can be used to study the ingress of oxygen into the goaf in different ventilation scenarios and goaf drainage arrangements. This approach not only helps the design of effective gas control strategies but also the management of spontaneous combustion risk in the goaf. Innovative goaf inertisation strategies have been developed and implemented during longwall sealing operations. Work is continuing to develop general guidelines of proactive goaf inertisation strategies to suppress the development of spontaneous heating behind active longwall faces.

Jan 1, 2005

By Richmond GD

The Hellyer concentrator of Aberfoyle Limited commenced production in 1989 processing a fine grained, massive sulphide ore containing Zn, Pb, Ag, Cu and Au as values. Four concentrates are produced - copper/silver, lead, zinc and bulk (Pb/Zn) - with overall payable recoveries (1991) of 80 per cent Zn, 55 per cent Pb, 50 per cent Ag, 30 per cent Cu and ten per cent Au. Metallurgical development work commenced immediately after plant commissioning, and continues. The flotation response and liberation analysis on a size basis highlighted reagent balance problems associated with tower mill regrinding of sphalerite, poor conditioning of flotation pulps, poor selectivity for fine galena, and insufficient liberation. These were the main causes of values lost to tailings, values reporting to the 'wrong' concentrates and of impurities in the concentrates. Modifications to tower mill regrind circuit operation, and the use of improved conditioning techniques have greatly improved concentrator performance, particularly in the finer (-5 micron) size fractions. Studies of concentrator and laboratory flotation by size and liberation analysis are the basis of diagnostic metallurgy. The techniques used to evaluate the improved concentrator performance are discussed.

Jan 1, 1993

IntroductionHistory of MineTopographyGeology of AreaGeneral DescriptionIgneous Rock TypesGranodioriteQuartz monzoniteApliteGranite porphyryMetasomatic ActionAlteration of monzonite/Alteration of apliteGeology of Ore BodyNature of OreZones of MetasomatismAssociated Fracture PlanesDistribution of Copper MineralisationNature of Copper VeinsQuartz-chalcopyrite veinsQuartz-calcite-chalcopyrite veinsEuhedral quartz veins/Non-euhedral quartz veinsStructures Accompanying Ore BodyApliteIntersecting lines of metasomatised monzoniteMetasomatised aplite

Jan 1, 1949

By T Hausler

The pitfalls, pleasures and management issues associated with international and remote projects are diverse.However, no problem is insurmountable and if an engineering team chooses (by luck or good planning) to push through the difficulties, success can mean an extremely satisfying experience for individuals and a significant, positive result for an organisation.International projects are not for the faint hearted or inflexible. Working in foreign lands with people who may or may not speak English and who may not initially respect you can become mentally and physically tiring.Sometimes the challenges are not fully explained to individuals in advance. Individuals then often learn about the challenges ù and discover solutions ù on the job. While this initially puts great pressure on individuals, matters improve eventually, especially when the locals come to understand that you are on site to make a positive difference.This paper will discuss aspects of a recent international project including meeting international clientsÆ expectations, dealing with cultural differences, social reckoning, environmental issues, and personal challenges. Specifically, it will cover aspects of working within a Russian cultural setting and overcoming social barriers.The paper also presents coping strategies for long periods of time spent away from home in remote places with extremes in weather beyond the normal experience of most Australians. For example, dealing with the effects of the spring thaw and coping with temperature ranges of -45 to +45¦C.Lastly, and possibly most importantly, there will be a focus on the role of translators. They have the power to make an engineer everyoneÆs best friend or, on your behalf, to order cold chicken liver and heart salad for lunch. If an engineering team can establish a working relationship with translators, they can become an invaluable asset and both on and off site.CITATION:Hausler, T, 2013. Achieving success in large-scale, remote area metallurgical plant projects, in Proceedings MetPlant 2013 , pp 539-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

Severe development difficulties were experienced soon after in-seam mining commenced at Appin Colliery in'1962. Thirteen years later no significant pro- gress had been made in overcoming some aspects of this development problem. Some success had been achieved in destressing roadways both in development and pillar extraction. Longwall retreat mining had shown promise of being highly productive but at an extremely high cost in terms of development requirements both in number of roadways and intensity of support in those roadways. No real advance was made in the problem of driving the first heading of a group of headings under conditions of apparently high stress in directions other than the preferred mining directions, although failure of the roof in this heading did seem to give easier work in the subsequent headings driven particularly if they were driven on narrow centres.

Jan 1, 1976

By Chavant G, Begis D, Gunther J

To study the ventilation of a mine (improve on the existing situation, examine extension projects) the calculation program used must take into account all the resistance values in the branches of the network. These resistance values are generally determined by measurements, which are accurate to a greater or lesser extent. In order to arrive by calculation at the flowrates measured :n the mine at a given moment, the resistance values have tto be adjusted experimentally. This manual operation is lengthy and delicate.

Jan 1, 1988

By Hayashida O, Numata Y

Ultraviolet and infrared spectroscopic analyses and the extended lluckel molecular orbital method were applied to determine the electronic and binding states of 2-mercaptobenzothiazole and the adsorption system of 2-mercaptobenzothiazole on pyrite. 2-mercaptobenzothiazole exists rather in thione form than in thiol forru and the two adsorption peaks in solution were assigned to both 7t--?rt* transitions. 2-mercaptobenzothiazole chemically adsorbs on pyrite mainly due to forming the bond between iron (pyrite) and sulphur (2-mercaptobenzothiazole).

Jan 1, 1993

By Cutler JL

At the present stage of the Rundle oil shale project planning, with depressed world oil prices, early development of the resource is unlikely. However, this postponement is being used to carry out technical studies required to evaluate alternative rehabilitation strategies and establish a sound environmental planning basis. Major technical data from the following studies are reviewed: Resource: - mine planning; material characterisation; retorting; geology; Environmental: - meteorology; surface water management; laboratory and field leachates; revegetation; waste characterisation; hydraulic and chemical modelling; dust suppression; plant/water interactions; and impact evaluation. These studies have shown that topsoil replacement, seeding mixtures, fertilizer application rates, subsoil quality and handling, waste pile slope and most importantly soil water storage are key factors in successful rehabilitation.

Jan 1, 1987

Gravity concentration of tin at Renison Limited uses tables and spirals to treat the various coarser fractions produced from sulphide flotation tailing. An acceptable final tailing cannot be made from one pass over the tables and spirals and therefore the tailing from these separators is reground and combined with the sulphide flotation tailing as the feed to the classification section. The gravity section became increasingly overloaded in the years preceding 1976 due to efforts to maximize tin recovery to the gravity concentrate. In April, 1976, two 2DSV Reichert cone concentrators in series were installed to treat the table and spiral tail- ing stream, prior to regrind, to scavenge a small tonnage of hard, coarse low tin grade material for rejection to final tailing. Gravity section loadings were decreased markedly, allowing operator attention to be directed more to table performance than to spillage collection. An increase in mill throughput of approximately 15% was possible following the commissioning of the Reichert cones. The cones are currently operated to make the minimum tonnage of tailing consistent with reasonable- gravity section loadings.

Jan 1, 1978

By de Brodtkorb MK

Late Cenozoic ore deposits "Precious and base metal-rich" and " Sn-Ag-polymetallic"of Northern Puna are associated either with Middle Miocene dacitic volcanic-dome complexes or with Upper Miocene dacitic-andesitic volcanic centers. Ore mineralogies and their related volcanism are discussed. A strong link is observed between the Cenozoic Metallogenetic Province of Northern Puna and the Southern Bolivia Tin and Polymetallic provinces.

Jan 1, 1995

By Yu H, Wan B

40 percent of the coal reserves and 40 percent of the ouput of coal in China is of thick coal seams. The sub-level caving in Yangguan has evolved together with the hydraulic supports, to provide recovery rates today of 80 to 85 percent, waste ratios less than 10 percent and daily outputs exceeding 7,000 tonnes. Matching of rate of shearing bottom coal to caving of top coal is most important to achieve "simultaneous" operations. Spontaneous combustion in the goat, gas, including in the goal, and dust, are particular safety hazards which are combatted with various stringent measures.

Jan 1, 1991

By Barria J, Mencho J, Gonzalez GD

An extended Kalman Filter is used to build an on-line estimator of total ore, fine ore and water hold-ups in a SAG mill. In addition, an equivalent grinding rate from coarse to fine ore, as well as the discharge rates of solids (fines) and water are also estimated as part of the adaptation procedure of the model used for the Kalman Filter. The measurements used in the Kalman Filter estimator are the total mill weight provided by load cells, and inferred discharge flows of fines and water from flow and density measurements performed downstream. The net ore and water feed to the SAG mill are used as inputs to the estimator, and also the proportion of fine ore in the feed. As an example of how to introduce robustness in the estimation in the face of sensor bias errors, an estimation of the load cell bias error is introduced in the estimator, thus providing self calibration. The estimator presented in this paper has been tested by simulation using a detailed SAG mill mechanistic dynamic model comprising 27 size fractions well fitted to a pilot mill. The maximum error in the estimation of the operational variables - total and fine ore as well as the mill contents under different operating conditions - is about ten per cent.

Jan 1, 1993

By Reid T. W

This paper describes the results of investigations into the relationship between specific gravity and chemical composition in the Cockatoo Island orebody, In the early investigations the samples were classified into groups according to porosity. This resulted in high, medium and low porosity groups, the latter being further subdivided into ore and waste. Whole number tonnage factors were assigned to each group. In the later investigations the reciprocals of bulk specific gravity and true specific gravity were ex- pressed as linear combinations of iron, silica and alumina using stepwise regression. The efficiency of the models as predictors was tested by dividing the data into two sets; one of which was used to calculate the regression equation and the other to test the efficiency of the equation as

Jan 1, 1976

The story of the Penjom gold mine located near Kuala Lipis on the Malay Peninsular demonstrates the valuable role successful exploration companies can play in the development of the gold mining industry. Avocet Mining PLC ('Avocet') began exploration in the area on a limited budget in 1989, securing land tenure around the Penjom alluvial workings in July 1990. The lease granted, known as Block 7, formed part of a land package offered at the time by the Pahang State Government to develop the resources of the area. Until the late-1980s, the Kuala Lipis region, situated approximately 180 km north west of Kuala Lumpur, had restricted accessibility for security reasons precluding serious exploration or mining activity. The situation has changed dramatically in the 1990s, with several foreign explorers active in the Peninsular, targeting old alluvial and underground workings adjacent to the north-south trending Raub-Bentong Suture. Deeper drilling of these prospects has shown there is potential for both small- to medium-scale open pit mining and possibly underground operations, providing companies such as Avocet with an ideal mining investment opportunity.

Jan 1, 1997

Spatial data processing using geographic information systems produces qualitative results which are superior to those from other existing software tools. However, the answers to various quantitative questions in mining operations is often limited by the capacity of the GIS to process appropriate spatial data. The efficient operation of a large underground mine demands that an adequate GIS be put in place.

Jan 1, 1995

By Fitter JF

Drilling and blasting practices at Groote Eylandt are undergoing a period of rapid change. Practices over the last ten years are reviewed and some specific blasting problems currently being faced are described. A move from percussion to rotary drilling is outlined, together with the reasoning behind a proposed return to ANFO from watergel explosives. A brief outline of the various firing patterns used is given, together with a description of the drilling and blasting recording procedures currently in use. Current and planned developments in drilling and blasting at Groote Eylandt are also outlined, emphasizing the success of wide patterns, fired in line with long inter-row delays.

Jan 1, 1982

Australian coal mines have spent considerable capital on dragline improvements over the last two years. This has included ~$30 M on UDD conversions, >$20 M on new buckets, boom upgrades, electrical upgrades, etc. This is a natural part of the response of mining companies to technology and replacement programs. Capital expenditure is a normal part of the ongoing success of most companies. There is however, a tendency for some people to rely on the capital alone to provide the ongoing improvements in equipment productivity. Implementing new technology through capital expenditure is only part of the equation in continuous improvement. For 80 - 90 per cent of the year, the operator controls the productivity achieved by the dragline. Variation between operators is huge. The average standard deviation in productivity is 12 per cent and maintenance impact is over 40 per cent. Robbins 2003, states: Contrary to what we were taught in grade school, we werenÆt all created equal. Most of us are to the left of the median on some normally distributed ability curve. Further, he states: The issue is knowing how people differ in abilities and using that knowledge to increase the likelihood that an employee will perform his or her job well. There are two options for reducing variability between operators; improving operator ability and getting the machine to take over what the operator is doing (automation). Dragline automation will be discussed, however, this paper will focus more on the æhuman factorÆ and how to establish a dragline with minimum variability between operators.

Jan 1, 2005

By Giannini LM, Carras S

A fundamental problem in mine planning is that of determining the "optimum pit limit" of a mine. This optimum pit limit yields information which is considered essential in the evaluation of the economic potential of a mineral deposit, and in the formulation of long -, intermediate -, and short-range mine plans. Since the mid 1960's a number of mathematical techniques based on the "block model" have been proposed for solving this problem. When applied to large ore-bodies the implementation of these techniques, especially the more elaborate ones, poses considerable computational problems. In this paper we report on our work, done jointly with Systems Research Institute of Australia (SRIA), in devising strategies for overcoming these Problems.

Jan 1, 1986