Search Documents

By S. P. Rivers

The stainless steel industry re1ies on nitric-hydrofluoric acid (HNO,/HF) pickling solutions to remove surface contaminants and maintain the corrosion resistance of the steel. More stringent environmental guide1ines are expected to be placed on the disposal of these solutions which could significantly increase processing costs. The U.S. Bureau of Mines has been conducting research to develop a process for recycling depleted pickling solutions, thus reducing the quantity of by product acids generated. Research has shown that F- can be liberated from the predominant iron fluoride species (FeF,') by using oxalic acid in an electrodialysis cell. Ion selective membranes allow dissolved metals in the depleted solution to be replaced with hydronium ions by metathesis, thereby regenerating the HF. The regenerated HN03/HF is then retained in the pick1ing solution. This paper reports on the research effort at the U.S. Bureau of Mines Rolla Research Center to apply electrodialytic recycling to HN03/HF pickling solutions.

Jan 1, 1993

By Thomas M. Harris

To avoid the escalating cost of disposal of metals-containing wastewater and residues, new wastewater treatments will focus on the recovery of the metals. A combination of ion exchange and electrowinning can produce water suitable for discharge and relatively pure metals. The use of a chelating resin can enhance the selectivity of both the removal process and the elution of metals from the resin. A new, simple method of preparing a variety of chelating resins is being developed. The materials produced by this method exhibit interesting, as well as potentially useful, elution behavior. The performance of one test resin is described.

Jan 1, 1992

By Zhijing Zhang

The management of hazardous wastes is important in a society which is increasingly concerned with environmental issues. Incinerators such as the slagging rotary kiln are widely used in the treatment of hazardous wastes. However, in order to assure a smooth operation of the rotary kiln, the melt should have both a low melting point and high fluidity. In this study, the fluidity of various hazardous waste rotary kiln slags was measured in terms of length of flow using the crucible test technique. It was found that the slags have melting points ranging from 1372 to 1424°C while their fluidities varied from 61-102 mm. The effect of addition of oxides on the fluidity of a slag containing 47 wt% SiO2 was also investigated. For this slag, additions of SiO2 (up to 56 wt%), FeO and Na20 increased fluidity, whereas the addition of CaO and A1203 resulted in lower fluidity values.

Jan 1, 2002

By C. S. Griffith

Lithium Australia NL (ASX:LIT) and ANSTO Minerals have been working together since 2015 on the development of halide accelerated leaching for the extraction of lithium from lithium-bearing micas, spodumene and clays. This technology has been termed SiLeach® process. The driving force behind development of the SiLeach® process, initially, was to develop a hydrometallurgical process to extract lithium from micas and spodumene without the need for the energy intensive, high temperature processing conventionally applied to lithium extraction. This driving force remains today and continues to hold promise in realising the value of previously under-utilised lithium resources. A comprehensive understanding of the technology and its applicability to the processing of micas and spodumene currently exists, and the flowsheet has been rigorously piloted. Production of battery grade lithium carbonate has been demonstrate

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By J. M. Boxall

The electrolytic zinc plant at the Bartlesville division of Z.C.A. originally used lead anodes containing only 0.25% silver because only H.G. zinc and alloy was to be produced. In 1984, a small addition of strontium carbonate was made to control the surf ace morphology of the cathodes which reduced short circuits and increased current efficiency. Later a drastic reduction in colloid addition further reduced short circuits. Increased strontium additions allowed the production of some S.H.G. zinc. Increasing the silver content of the anodes reduced the lead in cathodes only slightly. More important, the anode scale that was not removed during anode cleaning, entered the electrolyte and contaminated the cathodes with lead. A piping system has been installed to purge the contaminated electrolyte directly back to the leaching section. This has allowed the plant to produce S.H.G. zinc consistently.

Jan 1, 1990

By S. P. Mathew

The ISASMELT Lead Process is a continuous two stage process for the production of crude lead from concentrate. It is based on the use of a top entry submerged Sirosmelt lance to produce turbulent baths in which high intensity smelting or reduction reactions can occur. The process involves oxidizing the concentrates in the first stage to produce a high lead slag. This slag is tapped continuously and transferred down a launder to a second furnace where it is reduced with coal. Crude lead and discard slag are tapped continuously from this furnace through a single taphole and separated in a conventional forehearth. Process and engineering design work for a commercial scale Lead ISASKELT plant designed to produce 60000 tpa crude lead has been completed. This plant is planned to be operational in 1991.

Jan 1, 1990

By Raymond M. Coveney

Bedded sulfide ores in Cambrian Chinese black shales typically contains at least 2% Ni, 4.5% Mo, 1% As and 0.2% Se. Thin laminae and replaced on colites from the ore contain intimate mixtures of fine-grained Ni-rich sulfides and jordisite complicating ore treatment. The ores contain abundant jordisite, vaesite, nickelian pyrite, and barite and lesser amounts of sphalerite, gersdorffite, millerite, tennantite, fluorite, chalcopyrite, and HgSe (probably tiemannite). At present only ores that are sufficiently rich (>4.5% Mo) for direct roasting are mined and treated to produce, ammonium molybdate. The ores contain Pt, Pd, and Au in amounts totaling up to -2.5 ppm, but these are not recovered.

Jan 1, 1993

By Guo Xueyi

The morphological characteristics of the nickel particles electrodeposited from chloride dominant aqueous solution was investigated. The effects of the electrolyte constituents, the parameters for the electro-deposition on the morphology of the nickel particles were addressed. It is evidenced that not only the particle size but also the morphology of the deposited nickel particles strongly depend on the electrolyte constituents and technical operation conditions. The electro-crystallization mechanism of the metallic nickel particles deposited at high current density was elucidated. The ultra-fine nickel particles with flake, nodular or dendrite shape may be produced by controlling the duration for electro-deposition.

Jan 1, 2003

By Qingchun Yu, Baoqiang Xu, Yongnian Dai, Bin Yang, Fulong Zhu

"In this paper, the mechanism of the carbothermic reduction-chlorination process to extract aluminum from alumina in vacuum was investigated. The carbon monoxide (CO) content of the gas, phases of the reduction slag, surface morphology of the reduction slag and the product aluminum were measured by means of gas chromatography (GC), XRD, and SEM. The experimental results indicated that the content of CO in the gas decreased, but Al4C3 increased with time at 1773K during the carbothermic reduction process of alumina. AlCl(g) and graphite (C) were produced by the reaction between Al4C3 and AlCh(g) at 1773K, and then aluminum beads generated after the decomposition of AlCl(g). It implied the mechanism of alumina carbothermic reduction-chlorination process in vacuum involves three steps as follows: the carbothermic reduction of A}z03 to produce Al4C3, the chlorination of Al4C3 by AlCh(g) to produce AlCl(g), and the decomposition of AlCl(g) to produce Al(l).IntroductionAluminum is the basic raw material for many industries [1], and it is used extensively because of various excellent properties such as light weight, good malleability, high strength, excellent thermal conduction, high corrosion resistance and so on [2]. Industrial production of aluminum currently includes refining alumina and electrolytic aluminum processes. However, its development has been effected by some factors such as high energy consumption and heavy environmental burdens [3]. In the past several decades, there had been numerous attempts to produce aluminum by new methods. Extracting aluminum from alumina or bauxite directly by carbothermic reduction-chlorination process had been studied [ 4-6]. Although the alumina carbothermic reduction process [7~9] had been studied, the mechanism of the carbothermic reduction-chlorination process had not been systematically elucidated.In order to investigate the mechanism of the carbothermic reduction-chlorination process in vacuum, GC, XRD and SEM techniques will be used to determine the CO content and to characterize the surface morphology and composition of the slags at various temperatures."

Jan 1, 2011

By David M. Davidson

Seven intrusive phases have been mapped to date in the 1 b.y. Red Bluff Granite Complex (RBGC) near El Paso, Texas. This batholith is 20 km2 in area and intrudes older supracrustal units as well as a trachyte ignimbrite cap. Two early microgranite sills are spatially separated 6 km from a porphyritic, three-phase "ring complex" by a tin-bearing, biotite granite which cores the RBGC. These units are intruded, in turn, by a riebeckite granite which locally exhibits lineated and pegmatitic textures as well as exceptionally high light REE and Zr values (800 ppm La; 3,000 ppm Zr). The riebeckite granite is exposed in three separate occurrences within the Franklin Mountains. REE values in the RBGC are depleted in HREE and show distinct negative Eu anomalies. Typical La/Yb ratios are 5:1-2:1 with Eu values ranging from 10-80 ppm. The mineral source of the high REE values in the riebeckite granite has not yet been specifically identified, but is believed to be zircon.

Jan 1, 1988

HW Process Technologies, Inc. (HWPT) has developed a patented membrane-based ion fractionation system, which specifically separates copper from gold and silver species in a cyanide matrix. This Engineered Membrane Separation (EMS?) system was pilot demonstrated on the 82,000 liters of pregnant leach solution&apos; (PLS) generated from tailings, via thin layer leaching, at a mine site in Durango State, Mexico. The EMS? recovered ~90% of the gold-silver cyano-complex to a 90% volume permeate (based upon an EMS? feed stream of 100% volume) while rejecting -90% of the copper cyano-complex to a \0% (by volume) concentrate. The EMS? technology combines pore-size specific electro-statically charged membranes with engineered materials of construction and application-specific operational design that reject multi-valent, ionically charged species to the concentrate and transmit mono-valent species through the membrane to the permeate. The 850 ppm Cu PLS contained approximately 0.8 gil free NaCN with, the copper cyano-omplex principally in the CU(CN)3 and CU(CN)4 forms. The gold grade of the PLS was -2 ppm Au. The ~LS calcium concentration at -700 ppm Ca was reduced to ISO ppm.Ca (± 50 ppm) by sodium cycle ion exchange pre-treatrnent prior to EMS? processing.

Jan 1, 1998

By Li Qian

Mechanisms of bio-dephosphorization from iron ore was investigated in this Paper. The results show that there are two bio-dephosphorization ways from iron ore, the one is that Acidithiobacillus ferrooxidans directly derive phosphorus from the ore, the other is phosphorus is able to be leached acid produced during metabolizing of Acidithiobacillus ferrooxidans, and the latter is more important than the other. Adding suitable pyrite can enhance the bio- dephosphorization process through providing nourishment and producing acid directly due to S 3oxidized or indirectly due to Fe3 as oxidant. The potential varies in the range of 0.434~0.498V and pH is in the range of 2.5 ~ 1.25 during bio-leaching process. It can be founded that, according 2+to the E-pH graph of Fe-H2O system, Fe wouldn?t be oxidized under sterile system in this potential and pH ranges. It can be obviously concluded that the Acidithiobacillus ferrooxidans are 2+able to reduce the potential for the oxidization of Fe and make the oxidization occur in the above pH and potential zone, so the bio-leaching process can proceed. the investigation of E-pH graph of P-H2O system show that H3PO4 can exist steadily.

Jan 1, 2009

By Mikiya Tanaka, Mikio Kobayashi, Mansour A. S. A1Ghamdi, Kenji Tatsumi, Yukinori Saiki, Hirotaka Senba

"In order to recover nickel ion in a spent electroless nickel - phosphorus alloy plating bath and, at the same time, to remove impurities such as iron and zinc, the applicability of solvent extraction with LlX84I as the extractant has been investigated using actual spent solution. Although the extraction efficiency of nickel from the spent solution is considerably lower than that from the nickel sulfate-nitrate solution, nickel in the spent solution is selectively extracted with high efficiency at the pH of 6 - 7. The extracted nickel is effectively stripped by sulfuric acid at a pH of less .than· 3. On the basis of these results, a· flowsheet for recovering nickel from the spent solution is proposed Chemical equilibrium calculations of the spent solution has shown that the complex formations of nickel with anions such as lactate and phosphonate ions become predominant in the pH range between 2 and 6. This results in the depression of nickel extraction efficiency from the spent solution as compared with that from the .nickel sulfate-nitrate solution. By combining these aqueous equilibrium calculations with the· extraction model considering the extraction stoichiometry and the aggregation of the extractant in the organic phase, the extraction behavior of nickel is quantitatively predicted.IntroductionElectroless plating is indispensable for the recent advanced industries such as the electronic and mechanical industries. Electroless plating baths are repeatedly used by supplying the metal salts; however, the accumulation of the counter anions of the metal ions, the components formed by the oxidation of the reducing reagents in the plating baths, and the metal ions as impurities dissolved from the surface of the objective materials degrades the· quality of the plating. Thus, the baths are finally treated by a precipitation method to form a large amount of metal sludge, which is disposed in dumping sites. Therefore, from the standpoints of environmental protection and resource preservation, it is highly desired to establish a recycling process of the plating baths with minimum emission. Solvent extraction seems to be one of the 'suitable methods to recover metals from the spent electroless plating baths, because the concentration of the metal ion in the baths is relatively high, which is advantageous to solvent extraction as compared with the ion-exchange and adsorption methods. Some studies about the application of solvent extraction have already been carried out using simulated spe11t electroless plating baths [1-3]."

Jan 1, 2000

A study was undertaken to remove the Se from waste solutions using a raw form of the biomass called Iota Chips derived from the seaweed, Eucheuma spinosum. Removal of Se from solutions was investigated as a function of time, pH, conc. of Se in solution (0.1 to 100 ppm) and lota Chips to liquid ratios of 10-2 to 10-5. For solutions containing initial conc. of 0.1 ppm Se, with the addition of Iota Chips at a solid to liquid ratio of 10-3, the Se conc. decreased to 0.03 ppm in about 3 hours. Iota Chips absorption capacity to the Se and its application to the treatment of the metallurgical processing effluents are discussed.

Jan 1, 1992

By Chen Song

Cobalt basic carbonate particles were precipitated from 1.0mol cobalt nitrate or cobalt sulfate solution with ammonia carbonate. By controlling the zeta-potential of the particles and the ionic strength of the solution, the uniform particles with ellipsoid or rod shapes were obtained. During the precipitation process, the interface tension was diminished to the minimum and therefore the Ostwald ripening and secondary nucleation were both inhibited. The morphology and the size control by zeta-potential seem to be the result of thermodynamics rather than classical crystalline kinetics. The particle sizes were in the range of 0.4-0.6, 0.3-0.4 micrometer. After thermolysis, the spinel-type C0304 particles were produced. The morphologies of C0304 particles were similar to that of their precursors.

Jan 1, 2003

By C. S. Simons

This paper presents a review of the extractive processes used in the production of nickel, with emphasis on developments since the beginning of the Second World War. Attention is given to the factors, many outside the nickel industry itself, which determined the direction of process research and strongly influenced the ultimate commitments to industrialize the resulting developments. An example of such a factor is the sudden surge in demand, far exceeding the then available nickel production capacity, that was caused by the advent of World War II; the result was the first serious consideration ever given to low- grade laterites as a viable source of primary nickel. Other factors discussed include such items as process development in the extraction of other metals - particularly copper; the availability of increasingly sophisticated materials of const- ruction; the advent of the "environmentalist" and related political developments; the massive escalation in the price of energy - particularly oil. The paper concludes with an attempt to forecast the nature of the most effective nickel process of the future, based on extrapolation from the economic and political situation that exists today.

Jan 1, 1988

By Motoyasu Sato

Highly pure pig irons were produced in a multimode microwave reactor from powdered iron ores with carbon as a reducing agent in the nitrogen atmosphere. The grains in compacted powder absorb microwave energy selectively. Microwave-matter interaction creates thermal non-equilibrium state microscopically and enhances chemical reactions and the phase mixing at the grain boundaries very rapidly. The visible light spectroscopic techniques was used to monitor the progress of the reactions. Up to 650°C, the heated powders radiate the continuous spectrum of blackbody emission. The small non-equilibrium hot spots rise, move and finally burst in to brighter light emitting from all over the surface at 650°C. CN molecules and Fe (I) atoms were identified in the recorded spectrum. These bursts are similar to the ?ignition propagation? normally observed in chemical reactions. The line spectra originated from CO molecules have not been detected yet. The solid-solid reaction could be expected between the iron oxides and carbon to produce CO2 directly. A loss in the sample weight was accelerated during the excess-emission. These are the clear evidence that microwaves cause thermally non-equilibrium state and accelerate reduction process. The reduction of iron ore is completed at 1380°C and relatively very pure pig iron was produced. It should be noted that the impurity level of Mg, S, Si, P and Ti is only 5-10% of what is found in the pig irons produced by modern conventional blast furnaces in the steel industries. The necessary amount of carbon needed was 1/2 compared to conventional blast furnace to produce the unit weight of steel, if we applied renewable energy or nuclear power for the microwave excitations.

Jan 1, 2006

By Marco Zurco, Claudia M. Mendez, Alicia E. Ares, Carlos E. Schvezov, Carlos M. Rodriguez

"Zinc-Tin alloys were solidified in horizontal form and the obtained results were analyzed. During solidification the distribution of temperatures were measured by using thermocouples located strategically along the length of the samples. From the measured temperatures the following parameters were derived; the local temperature gradient, the cooling rate and the velocities of the liquid and solids fronts. Comparing the structure of the samples and the values of these parameters it was found that the temperature gradient reaches minimum values of as low as - 0.6 °C/cm, and velocities of the fronts of around 0.1 cm/s. In addition, the grain size was measured along the samples. The results are presented and discussed in the frame of the results previously obtained for other alloys.IntroductionGenerally solidification leads to two types of grain morphologies: columnar and equiaxed. The origin of each one has been the subject of numerous theoretical and experimental researches in the field of metallurgy for many years [1-7]. The columnar-to-equiaxed transition, CET, is considered as an object of high technological relevance with respect to the directional solidification of metallic alloys. This structure transition may be sharp or gradual and it has been reported to be dependent on thermal conditions associated with the casting process, including melt convection, heat transfer coefficients at the metal-mold interface, growth rates, thermal gradients, cooling rates, transport of solute, alloy composition, melt superheat, mold temperature, mold design, casting size, casting geometry, and the concentration of nucleating particles. As a consequence, it is critical for industrial applications to understand the physical mechanisms which control this transition during solidification. Many studies highlight the importance of the relative growth of the equiaxed and columnar grains and develop expressions or numerical procedures to describe a criterion for the CET. A number of experimental investigations reported in the literature suggest that the CET occurs when GL in the melt reaches a minimum critical value [5-7]."

Jan 1, 2012

By Cong Wang, Siyang Long, Pengcheng Zhang, Haibin Zuo

This paper introduced the research progress of microwave treatment on coal. The mechanics of microwave treatment mainly include thermal effects and non-thermal effects. Thermal effects, which lead to cracks and changes of pore structure, attribute to the selective heating of microwave. Non-thermal effects involve the removal of oxygen functional groups, improvement of coal rank and decomposition of minerals. Therefore, microwave treatment of coal has a lot of potential applications, mainly including drying, desulfurization, improvement of grindability, enhancement of coal-water slurry property and change the combustion and gasification properties.

Jan 1, 2016