Search Documents

By Timothy C. Siegel, Paul J. Axtell

The Missouri Department of Transportation (MoDOT) recently replaced the Hurricane Deck Bridge that carries Highway 5 traffic across the Osage Arm of the Lake of the Ozarks in Camden County, Missouri. The former bridge was constructed in the 1920's and was supported on pneumatic caissons bearing on dolostone bedrock. The replacement structure is founded on drilled shafts socketed into the bedrock. During the design phase of this bid-build project, a baseline design was developed and Alternative Technical Concepts (ATC's) were allowed from approved contractors. Those ATC's were confidential and not shared between teams. Either the baseline design or the approved ATC design could be bid by the respective contractors. The baseline design included re-use of the 90-year old caisson foundations. Accordingly, an extensive evaluation of the caissons and underlying bedrock were conducted by coring, laboratory testing, acoustic tele-viewer (ATV), and cross-hole sonic logging (CSL) methods. The results of the investigation indicated the caissons were in excellent condition and suitable for re-use. However, a more cost-effective ATC was submitted, awarded, and constructed that did not re-use the existing caisson foundations but rather reduced the span lengths, increased the number of piers in the water, and supported those piers on drilled shafts. Interestingly, the difference in low bid price between the awarded ATC and the baseline design was less than one percent of the construction cost. This paper describes the multiple foundation designs that were necessary for this interesting project. The various foundation evaluations include the existing pneumatic caissons, large-diameter open-ended pipe piles to support the baseline design, and the design of rock-socketed drilled shafts that were successfully constructed in 2012.

Jan 1, 2017

By Paul Suver

The closed loop standing column well (CLSCW) system uses a closed circuit of water to develop the same thermal heat exchange characteristics that are achieved from traditional open circuit standing column well that uses the ground water directly. Pipe pile and pipe anchor foundations can be used as CLSCW components for ground source heat exchange. New data gathering and analysis techniques and equipment installed in the heat pumps allow any mechanical engineer to design the system without specialty engineering equipment and certifications.

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By Josef K. Alter

Long-term performance and behavior of post-tensioned ground anchors subjected to axial cyclic loading constitutes an important aspect of the stability, reliability and overall performance of wind turbine deep foundations. Axial cyclic loading of post-tensioned (PT) ground anchors in soils has not been thoroughly investigated as evidenced by the research conducted for this topic. This paper evaluates research test data, available literature, and industry expert opinion on the current status and problems of deep foundation post-tensioned ground anchor (PTGA) technology, as applicable to the wind energy industry. It also introduces a proposed design solution that addresses the problems of construction cost and long-term performance of wind turbine deep foundations in soils subjected to dynamic cyclic axial loading. Deep foundations using ground anchors for wind turbines have only recently gained attention as a possible viable alternative to the mass spread footings currently in use. One of the primary problems with general acceptance of current PTGA designs is the need for long-term anchor maintenance. The research that was conducted for this study indicates that current literature only partially addresses the many factors influencing load capacity and pullout performance of ground anchors. The lack of information indicates the deep foundation industry has fallen behind in designing and implementing new technology to improve safety and performance, ensure sustainability, reduce costs, and address environmental responsibility. This paper describes the significance of this problem as it applies to the wind energy market, and proposes a new technology solution. The research, expert opinion, and analysis presented by the author is used to support the premise that ground anchor construction cost and long-term maintenance can be reduced with PTGA systems using the Con-Tech Systems (CTS) patent-pending Groutable Void Form (GVF) technology.

Jan 1, 2010

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Pierre Gouvin

"This paper discusses real time monitoring of utility vaults during the reconstruction of the Elliot Bay Seawall in Seattle. The project, undertaken because deterioration of the old wall posed increasing risks to property and lives, impacts businesses, ferry terminals, a rail line, and electrical utilities that distribute power to much of the downtown area. The project, which has been fast tracked to minimize risk and commercial impacts, involves multiple contractors with heavy machinery working in an area one mile long and only a few hundred feet wide. This presented challenges to monitoring of the utilities, as will be discussed in the paper.INTRODUCTIONThe Elliot Bay Seawall (EBSW) was built in over a period of 18 years, starting in 1916. It consisted of a vertical concrete wall placed on a timber pilings and timber relieving platform. The seawall also retained fill that served as the foundation for a road known as the Alaskan Way. The seawall has performed well over the years, but now cracks in the concrete have allowed loss of fill, and the timber piles and support structures have been weakened by marine boring insects.The project to replace the seawall was undertaken because deterioration of the old wall posed increasing risks to property and lives. Because the project impacts businesses, tourism, ferry terminals, and a rail line, it was given a compressed timeline - 36 months from start to finish. In addition, construction activities have been staged carefully to minimize disruption of Salmon and other wildlife living in Puget Sound. In fact, will incorporate several habitat improvements to promote sea life, such as a nature-imitating textures in the surface of the wall and a glass deck structure that allows sunlight to reach the water. (Fig. 1) shows a schematic of the planned new wall.The sheet piling, concrete piles, jet grouting, drilled shafts, ground freezing, and demolition activities are all taking place in the narrow corridor that holds the subsurface ducts and vaults protecting Seattle’s electrical power distribution. If the network of duct bank and vaults were to experience differential settlement during work here, then most of downtown Seattle would be in the dark. Thus it was important to provide real-time displacement monitoring of these utility structures."

Jan 1, 2017

By Jon E. Bischoff

Construction of a secondary clarifier on the banks of Rainy River, Northern Minnesota, required the driving of H-piles 14HP102 to a sloping, very strong bedrock through thick deposits of soft and medium stiff soils. Pile toe protection, APF Hardbite HP 77750, was specified to prevent damage to the pile toe and to enable the pile toe to bite into the bedrock surface. The toe protection worked well for bedrock sloping less than 2H:1V. However, where the bedrock was steeper, the piles experienced damage and failed to reach bearing. In most cases, the also the replacement pile failed. Pile Driving Analyzer measurements showed that on encountering the bedrock, the pile toe reflection, which at first was sound, deteriorated indicating pile toe damage. Extraction for visual inspection showed that the failed piles were bent and had deformed pile shoes. In areas of steeply sloping bedrock and for replacement piles, an alternative shoe, the Scanpile Herkules rock shoe, was employed. This pile shoe proved to be able to secure the pile toe into the rock and to eliminate the problem. The costs of the Herkules rock shoe considering price, shipping, and attaching, were about equal with the Hardbite shoe.

Jan 1, 1993

By Frank Rausche

The more widespread use of Augered Cast-in-Place (ACIP) Piles has generated increased demand for improved quality control measures. These deep foundation elements are often relatively long and slender and their structural quality depends on the experience of the installers, the adequacy of their drilling and pumping equipment, and of course, the properties of the soil. Since the concrete of ACIP piles is pumped under pressure into the borehole, the piles may achieve a very high unit shaft resistance if conditions are favorable and the piles are well constructed. Three types of methods can help assure that the piles are properly executed. During construction, monitoring the volume of concrete pumped and the pressure applied helps avoid structural defects. After installation, and once the concrete has hardened, the Pulse Echo Method allows for a check of the structural integrity of the shaft. Finally, a load test, performed some time after installation, yields a check of both bearing capacity and structural integrity of an individual pile. Because of their expense and associated construction delays, static load tests are normally done for only a few piles. However, at large construction sites, it may be necessary to perform many load tests either as a planned construction control activity or as a means of spot checking or verifying suspect piles. For smaller sites, however, static load testing may be prohibitively expensive. In such situations, dynamic load testing, originally developed for driven piles, has frequently been employed for drilled shafts and ACIP piles. In the latter case special consideration must be given to the ACIP pile slenderness and their often relatively low concrete design strength, which may not tolerate high dynamic loading stresses even though their unit resistance along the shaft is relatively high. Lately, the dynamic load test has become more feasible with the availability of loading systems that are custom tailored to this particular pile type. These systems produce a low velocity, low stress and high energy impact. Recent developments have also made the instrumentation process simpler: force measurements are now made on the ram rather than on the pile for increased reliability and simplicity. This presentation describes the requirements for successful dynamic load testing of auger cast piles and summarizes results from several projects where the new loading system and newly developed instrumentation was employed. A few cases are presented correlating static load test results with dynamic predictions, calculated by CAPWAP®.

Jan 1, 2001

By I. K. Ozaydin

Analysis of piles groups loaded with large bending moments and both vertical and batter piles can be best performed by matrix analysis. In this paper, a case history about a tall marine control tower is presented. The soil conditions at the site and the results of the computer analysis of the piled foundation are summarized. It is shown that the pile loads are indeed less than the allowable load for a single pile. Pile head loads and moments are used in the analysis of the raft foundation.

Jan 1, 2010

By Christian L. Escalera

Over seven years ago, on October 29, 2012, Superstorm Sandy pummeled the Northeast of the United States inflicting heavy damage on New York City Transit’s (NYCT) system. Since then, NYCT has been methodically rehabilitating and hardening its assets to upgrade service and prevent future impacts caused by similar devasting storm surges. Part of these resiliency efforts, NYCT’s 207th St Yard Project is one of many projects that make up the Sandy Repair and Flood Mitigation Program. The work to be performed on the 207th Street Project includes building a perimeter Floodwall along the Harlem River, extending up 215th Street and 9th Avenue with the intent of having the ability to withstand a 500 Year Storm flooding event. The original 1,535 lineal feet of the marine side floodwall design consisted of 937 each W40x235 H-Piles continuously welded to PS 27.5 flat sheet to form an interlocked and composite steel seawall that would protect the NYCT 207th Yard from a storm surge of the Harlem River. However, after the Contract was awarded and a Notice to Proceed was issued, Walsh Construction Company II (WCCII) partnered with Mueser Rutledge Consulting Engineers (MRCE) to propose a redesign of the marine wall section as a Value Engineering Change Proposal (VECP). This VEP redesign is comprised of 279 each 54in Diameter Steel Pipe Piles that are interconnected with continuously welded PZ 35 sheet piles interlocks. The intent of the VEP was to provide a cost savings that could be shared by both parties as well as alleviate some constructability and alignment control concerns that WCCII had expressed to NYCT. The VEP allowed WCCII to substantially lower the total cost which was shared between NYCT and WCCII.

By V. Tang

In this paper, Chinese economic situation are estimated and prospective developments predicted to assist those US firms who have been trying to do business in China, or are considering to pursue the China market.

Jan 1, 2010

By Armin W. Stuedlein, Seth C. Reddy

In this study, factors affecting the reliability of augered cast-in-place (ACIP) piles under axial compression at the serviceability limit state are addressed using a simple probabilistic hyperbolic model and a database of load tests on ACIP piles in cohesion less soils. The aleatory and model uncertainty in a selected load-displacement model is statistically characterized, and is used to simulate representative random samples from the bivariate random vector of model parameters. A first-order reliability method (FORM) was used to determine the effect of sample size on the stability and uncertainty of the reliability index. Sample sizes greater than about 40 provided relatively consistent estimates of the reliability index; however, its uncertainty continued to decrease with increasing sample sizes. Additionally, the effect of slenderness ratio on the reliability of the serviceability limit state design was characterized and found to exhibit a significant effect on the probability of exceeding a specified displacement.

Jan 1, 2013

By Abid Adekunte

Traditionally, designers and contractors provide additional external supports to retaining walls through the use of tie-back anchors or braces. Both approaches are known to have their shortcomings; braces limit working space within excavation areas, while tie-backs are seldom used in built-up areas where intrusion into adjacent property of non-cooperative owners has to be avoided or in situations where sensitive structures exist behind the wall. This paper focuses on the design, construction and monitoring of deep excavation support systems on two separate projects located in different ground conditions in the Republic of Ireland. On both projects, conventional ground anchorage and propping were inapplicable. This led to the development and application of two different novel solutions on both projects. Methods of wall performance monitoring on both sites also differ. Wall monitoring results show these innovative methods to be safe and effective. Advantages of the novel solutions over traditional approaches are highlighted.

Jan 1, 2010

By Meeok Kim, Thornton Tomasetti, Seth Knihtila, Michael Oakland, Shawn Leary

The transformation of Seattle's historic KeyArena into the state-of-the-art Climate Pledge Arena, home to the NHL's Seattle Kraken, was no small feat. The $930-million renovation and expansion required the near-total demolition of the old structure and construction of an 800,000 sqf (74,000 m2), below grade venue while keeping its landmarked façade and roof intact. To do that, the project team had to come up with solutions for excavating 680,000 cu yd (520,000 m3) of soil to make way for the new 17,000-seat arena while working around the massive temporary shoring supporting the 44 million lb (20 million kg) roof all in time for the NHL's 2021-22 season.

Sep 1, 2023

By Pirooz Barar

The new Stanley Hall building will house the center for bio-engineering and technology research for the UC Berkeley campus. The structure is located at the northeast part of campus, adjacent to Donner Lab, on the west side of Galey Road, approximately 600 ft. from the Hayward Fault. The building site has a complex geological formation. To the east there are clayey soil shale formations, and to the west there is greywake shattered sandstone. The water table is at 10 ft. below grade. The structure will consist of 6 levels below grade and 8 levels above grade, which calls for an 83 ft. deep excavation on the northeast side. There is an approximately 35 ft. grade differential between the east and west sides of the building. Because of this severe grade differential, as well as high water tables, the lateral forces on the building due to uneven earth pressures would have been 2 times the magnitude of the seismic forces. To mitigate the lateral earth pressures, a permanent Soil Nailed Wall, integrated with the structural system of the building was designed. PB&A, Inc.?s in-house design program ?Winslope? was utilized to design the system and the data obtained from a rigorous monitoring program, were used to calibrate several computer runs using Plaxis program.

Jan 1, 2004

By Jim Bruce

This paper presents details of a slope stabilization scheme built in late 2003 at a 16m-high railway embankment in southern Ontario, Canada. The owner, faced with continuing maintenance and safety issues arising from numerous nuisance slides, and residential neighbors in close proximity to the slope, sought new proposals to replace a previous recommendation to cut down all trees and undertake a deep soil nailing scheme. A non-reticulated micropile array with surface cap beam was proposed and built on the south side of the embankment with no tree removal required. A detailed FLAC analysis was completed, using multiple iterations to arrive at the eventual, optimized micropile depth and spacing. Analysis predicted an 18% increase in the factor of safety. Short term inclinometer monitoring and performance evaluations in the months since construction so far corroborate the prediction.

Jan 1, 2004

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

By Alexander Blatt, Franz-Werner Gerressen

Diaphragm walls are known as underground structural elements commonly used as retention systems for excavation pits and shafts and permanent foundation walls or elements. One can anticipate that global urbanization and increasing demands on environmental considerations will need to be accommodated in underground space in the future. These trends show an increasing requirement for diaphragm walling in even more complex conditions, especially in inner-city applications with limited space. Complex conditions in terms of space limitations, especially for inner city job sites, require specifically adapted solutions for slurry, spoil, reinforcement and concrete handling and the related logistics to ensure smooth production. Furthermore, one focus will be given to the QA/QC topics of the production process. Real time installation control, data transfer and reporting systems become more and more important. Therefore, the paper will describe the construction method and the sequence of activities required for the construction of diaphragm wall systems. It will describe also the main equipment that will be needed to execute these works under various conditions. In addition to the general description of the system and the required equipment, the paper will show some site examples for infrastructure projects with their specific solutions when working under space restrictions.

Nov 1, 2022

By Mohamed A. Mansour, Ahmed M. Soliman, M. H. El-Naggar

"Grouted helical piles allow significant increase in pile capacity with low additional cost over that of conventional helical piles. They can be particularly advantageous in sites where installation disturbance can reduce or even eliminate the pile shaft resistance. For helical piles with slender shafts, a grout column offers increased buckling resistance under compression loading, and may reduce the potential settlement required to mobilize the bearing component of their plates. This paper investigates the performance of grouted helical piles installed in loose sand. Grouted helical piles were constructed and tested in a controlled laboratory environment. Helical piles with hollow pipe shaft and single helix were grouted during installation. The grout was injected into the soil under high pressure through two nozzles placed above the piles helices. The load test results showed significant improvement in the performance and load carrying capacity of the helical pile due to the formation of a cylindrical grout column along the entire shaft leading to a higher shaft resistance contribution to the total pile capacity. The results suggest that grouted helical piles with slender hollow shaft could be used to support large structural loads. INTRODUCTIONHelical piles are widely used as a deep foundation system for different engineering applications. They represent an attractive foundation option because of their cost effectiveness, ease of installation even in limited access areas, low levels of noise and vibrations, and their ability to be installed through ground water without casing. In addition, they allow immediate loading upon installation. Helical piles are installed into the ground by applying a mechanical torque to the pile head. The installation torque monitoring provides a kind of quality control during the construction of helical piles. It could be used in predicting the ultimate pile capacity using several capacity-torque correlations (Livneh and Elnaggar 2008; and Hoyt and Clemence 1989).However, helical piles installation can cause soil disturbance within the annular zone affected by the pile helices. This disturbance can introduce fissures within the pile cylindrical failure surface (Vesic 1971; Mooney el al. 1985; and Zhang 1999). Thus, the shear strength of the soil decreases along the affected zone. Bagheri and El Naggar (2013) evaluated the installation effects of helical piles in sand. They reported that as the helical blade proceeds into the ground, sand within the cylindrical path circumscribed by the helices experiences torsional and vertical shearing accompanied by sand displacement and stress changes. This process is more pronounced in the case of multi-helices and large diameter anchors. Bagheri and El Naggar (2016) evaluated the installation effects of helical piles in structured clay. They indicated that the behavior of the helical pile and its capacity are significantly affected by the degree of soil de-structuring induced by the penetration of the pile shaft and helices. In addition to the installation disturbance, helical piles have other drawbacks including; high potential settlement required to fully mobilize the bearing component of their plates, low buckling resistance of their slender shafts, and the incomplete rigidity of the coupling joints along the pile shaft that allow some lateral movement under compression loading (Vickars and Clemence 2000)."

Jan 1, 2016

By Eric J. Pederson

The down hole hammer is widely used in specialty geotechnical construction. The common uses include tie-back anchor installation, micropile installation, and general soil/bedrock drilling operations. Veit used these techniques to develop a cost effective way of installing the foundation system for University of Minnesota Football Stadium. The soils present at the site of the stadium contained layers of concentrated cobbles and boulders. The geotechnical engineer recommended a driven pile system, and the base bid outlined in the project documents consisted of an H-Pile using a 14x73 pile section. Veit submitted an innovative alternate consisting of using a rotary percussion system to install a 12? O.D. pile. This paper will show that this pile type and installation method was the correct choice for the project. The design criteria for the compression, uplift, and lateral capacities and deflections were met, while eliminating pile damage. The method resulted in a significant cost savings to the University and maintained the project schedule.

Jan 1, 2008