Search Documents

By L. T. Raevskaia

We discuss the stability problem of a piston of the reversible axial-piston pneumatic motor called DAR-14M. We performed the full analysis of stress and deformation characteristics of the piston near a resonant frequency with the help of FEM ANSYS. We estimated the own frequency of the piston analytically for the given motor, this estimate was confirmed numerically in the model analysis FEM ANSYS. It was also shown in harmonic analysis that loaded piston end behaves very different in comparison to the unloaded end. As expected, maximum deformation was found in the area of the holes of the bearing shaft, indicating an optimization necessary in that region of the motor.

Aug 1, 2013

By J. W. Matousek

Since the late 1800s, copper-nickel ores have been mined and smelted in the Sudbury area. The Canadian Copper Company, the Copper Cliff ancestor of Inco Limited, commenced operations with a blast furnace smelter in 1888. Coal-fired reverberatory furnaces were added in 1911 and multihearth roasters in 1914. The blast and reverberatory furnaces smelted, respectively, coppernickel ores and ore fines until 1930, when a milling process and plant began operating to concentrate and separate the minerals of these two metals. Two reasons for this delay were: (1) the availability of high grade ores suitable for direct smelting; and (2) the difficulties in making the copper-nickel separation. The Mond Nickel Company, however, practiced flotation at its Coniston Smelter site from 1914 to 1930. A bulk concentrate containing six per cent copper and five per cent nickel was recovered from ore of 1.6 per cent each of copper and nickel. Gravity (table) and magnetic concentrates were also produced. Inco Limited (then The International Nickel Company) began laboratory-scale flotation tests on its ores in 1918. This work led, ultimately (in 1930), to the construction of the 7500 tonne-per-day Copper Cliff Mill, designed to recover separate copper and nickel concentrates. Its capacity was expanded to 11000 tpd in 1936, to 18 000 in 1940, and to 27 000 in 1942. Since 1971 it has operated to process only the bulk flotation products from other mills to yield individual nickel and copper concentrates.

Jan 1, 1999

By N. Giguère

Until recently, the heat treatment of pressure die cast parts has always been considered unpractical because the solution heat treatment resulted in unacceptable blistered parts. This was due to the presence of massive porosity associated with the die casting process where the inflow of metal inside the mold cavity is extremely turbulent. With the steady improvement of foundry practices and the generalization of vacuum die casting, porosity defects have been reduced to the point that a partial solutionizing heat treatment can be applied without any damage to the casting. However the solutionizing temperature must be lower than that applied to macroporosity free castings and for much shorter time. The object of the present study was to determine the optimum solutionizing temperature that can be applied to aluminum 383 die cast brackets along with the optimal temperature and time of aging resulting in the highest improvement in mechanical properties (both strength and ductility). This was done by testing strength and deformation on the casting itself using a specially designed jig; the crushing force to deformation curve was analyzed so as to quantify the improvement in both strength and ductility gained with the partial precipitation hardening heat treatment.

Jan 1, 2011

By E. Ettles

This paper features some of the spectacular new advances in the fields of fluorescent penetrant inspection and magnetic particle concentration. Casting fractures in the various stages -before the repair, during the repair and in the completed repair -using the cold process method will be discussed. This cold method of repair eliminates problems of pre-heating and cooling and the stress factors that are involved in any heat repair.

Jan 1, 1971

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By T. Kawai

Japan Oil, Gas and Metals National Corporation (JOGMEC) has started an exploration program for Seafloor Massive Sulfides (SMS) in the EEZ of Japan, and launched an investigation program for mining, processing and environmental impact on SMS development. With regard to the mining aspect, the mining system consists of three units: a mining unit on the sea floor, an ore lift-up unit to surface, and a mining support vessel unit which has an ore unloading system that unloads onto a shuttle ship. Regarding the mining unit, JOGMEC and certain Japanese mining and machinery companies developed two types of state of the art mining testing tools. Excavation tests on the actual SMS site in the Okinawa Trough, south-west of Japan, were conducted in 2012. In these tests, the functions of the testing tools, such as cutting ore, moving on the seafloor and climbing up slopes having steeper than a 25 degree gradient, were confirmed. The physical characteristics of the ore, which are key parameters for establishing a mining system, are yet to be fully understood as the exploration program has been undertaken simultaneously. Hence, those examinations have been carried out by ground cutting experiments, analysis of drilling core data, and the like. This paper describes the outline of a proposed mining system, mining testing tools and results of the on-site mining testing.

Aug 1, 2013

By John (Jack) D. Young, Frank M. Wheeler

Metallurgical plants are typically large, complex facilities. Their design is a multidisciplinary activity with a wide range of inputs, based on: the business case; metallurgical and process requirements; and the main processing equipment selection. Many constraints limit what can be achieved. Appropriate phasing of the design and development, and clear go/no-go decision criteria, are critical to successful implementation of a plant design project. Risk management concepts are used as a framework for successful project development, working from the business case, through project development, to implementation and startup, paying constant attention to technology, safe design, and sustainability. 1.1 INTRODUCTION The subject of “Metallurgical Plant Design” is the design of metallurgical plant facilities in the broadest sense. Plant design represents the culmination of many multidisciplinary activities: knowledge of process metallurgy is applied to design facilities to manufacture useful, economical, metal-based products. In the field of metallurgy, plant design is often overlooked, and its unique requirements are commonly not well understood, let alone appreciated. This book is a contribution to remedying this situation. The focus is the specifics of the metals industries, because an extensive literature already exists on the general topic of plant design.

Jan 1, 2015

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By M. K. Senicie

IN July, 1937, Asbestos Corporation, Limited, installed an automatic conveyor-belt scale at their King mine, Thetford Mines. The equipment was purchased 'on trial' and its performance has proved entirely satisfactory to the staff. The scale was manufactured by the Toledo Scale Company, of Toledo (Ohio) and Windsor (Ont.) and was installed by one of the Scale Company's engineers. The electrical recording equipment was installed by Keith Mercer, Reg'd, of Montreal, Canadian agents for the manufacturers, the Builders Iron Foundry, of Providence, Rhode Island. The recording equipment consists of a duplex weight-transmitter attached to the scale-head, a duplex totalizer with differential relays, a belt-speed compensator, a rate-of-delivery recorder, and a rate-of-delivery indicator. As it was desired to run the mill at maximum capacity, it was necessary to know the rate of feed at all times, so that any lessening of rate of feed or delays would be recorded and could be corrected. After having determined the rate of feed to the mill (100 per cent capacity), it was required to have weighing and recording instruments which would show: (1) The rate of feed per hour. (2) Any variations .in the load. (3) Any delays and the duration and time of the delays. Rate of tonnage recorders in the mill superintendent's office and at the point of feedi.ng were necessary, as was automatic control between the mill superintendent and the feed man. It was desired to have a permanent record of total tonnage fed per shift or day; weighing and recording mechanism had to have sensitivity to record all previously mentioned conditions. Mechanism had to be of rugged construction, and be so built that it would stay in good operating condition, with the minimum amount of adjustment and supervision.

Jan 1, 1938

By R. Heikkilä

As a part of a large research and development program in Finland, a system calibration for an UAV measurement method having practical experiments in a Jorvas Railway Yard design and construction project. The Railway yard construction are was measured using an UAV measurement device by Smartplanes (Smartone) and using some reference points measured by a GNSS device. The measured data was cleaned, combined and adjusted through Least Squares Optimization using the software developed by a Finnish company Pieneering Oy. As references, two different laser scans as well as total station surveys were used. For applicability evaluation, the accuracy of measurement, the reliability of measurement, and the economy of measurement were used. Based on the comparisons, the achieved precision of the UAV measurement was high, instead the accuracy of measurement was not sufficient in this case. The principle of this photogrammetric measurement includes a lot of redundant observations making it possible to achieve a high level of reliability. The economy in this Railway Yard Design project was not able to achieve.

Aug 1, 2013

By Min-Sung Kang

Excavation and earthmoving equipment mostly operate in accident-prone areas. These areas normally have rollover, confinement, and fall or may be considered harmful work areas due to demolitions and sewage removals. It is inevitable that excavation and earthmoving systems should be developed to secure the safety of operators through unmanned and remote control systems. Therefore, this research proposes a system that enables excavators to be unmanned and remote controlled without any renovation, remodeling, change, or transformation by applying attachable and separable mechanism and modules. Moreover, this research proposes the sensor module to evaluate the dynamic status without processing remodeling or transformation the existing hydraulic drive excavation system by adopting the easy attachable and separable mechanism. The study verifies this proposal based on observed possibility and feasibility through the experiments.

Aug 1, 2013

By I. Kylmakorpi

In non-ferrous metal smelting, when the concentrate entering the furnace contains high levels of moisture, energy requirement for heating and drying increases and large volumes of exhaust are produced. To solve this problem, rotary dryers and flash dryers using direct heating, and also steam dryers using indirect heating have all been used for drying concentrate. The focus of this paper is to present the development and current applications of the Kumera Rotary steam dryer. The advantages of this technology are numerous, including reduced heating requirements, environmental friendliness, operation reliability and minimum maintenance needs; making it a top choice for drying concentrate.

Jan 1, 2008

By M. Hamamoto, M. Furuta, S. Tanaka

The Tamano smelter and refinery has expanded its production from 228kt/y to 260kt/y since 2006. It was not a big jump, but efficient and economical improvements were executed. These were not only de-bottlenecking and modernization of the smelting plant, including the acid plant, but also additional processes were commissioned, e.g. slag cleaning furnace and steam dryer. On the other hand, a conversion to permanent cathode process in the #2 tank house made the biggest impact on production efficiency for the refinery plant. In order to overcome the drastic change of copper business, although each scale is not so big, continuous improvements are very important to survive. This paper mainly describes the recent improvements of the smelting plant.

Jan 1, 2007

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By K. Regl, J. Berneder

"AMAG investigated different aspects to improve the resistance against grain coarsening in aerospace alloys during recrystallization and was successful in finding several opportunities to minimize this effect. The studies show that one aspect to counteract grain coarsening is the chemical composition and subsequently all phases that are formed during homogenization. Starting with a fine grain (~ 50 µm) can lead to a final grain size of few mm. On the other hand with a coarse initial grain size (approximately 150 µm) and the right chemical composition the grain size can stay almost constant despite different deformation steps. Additional we investigated different sequences for the component production to eliminate the problem of grain coarsening as a coarse grain has a detrimental effect on product performance.INTRODUCTION In the aircraft industry, aluminium sheets are most commonly deformed in their soft state, followed by solution heat treatment and natural or artificial aging. If the preceding deformation is in a critical amount, during the recrystallization at solution heat treatment grain coarsening can occur. A subsequent deformation to this condition leads to an orange peel surface, which requires additional polishing. Next to this extra effort the coarse grain size produces a drop in the mechanical properties, often below specification limits. If there is no subsequent deformation, this effect is not visible and without destructive testing there is no possibility to detect the error. As mentioned before, this effect occurs during recrystallization, which is a process that is driven by the stored energy in the microstructure. The two most important aspects for an increase of the stored energy are the increase of the grain boundaries fraction (smaller grain size) and the increase of the dislocation density caused by deformation. The increase in dislocation density during the deformation arise from trapping of existing dislocations and from the generation of new dislocations. During recrystallization all grains are built completely new, so all dislocations are removed (Humphreys & Hatherly, 2004). There are three requirements for recrystallization:"

Jan 1, 2018

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

By W. R. Dodge

THE growth and development of the assay department of the Hollinger Consolidated Gold Mines, Limited, is a similar story to that of the mine itself. As the mine developed and enlarged, so also increased the demands upon this department, necessitating an increase of capacity for fire assaying and a widening of the scope of work to include chemical analysis, metallurgical tests, research, and screen analysis. The yearly total of determinations, taking an average for the past six years, is approximately 350,000. The major portion of this figure represents fire assaying for gold and silver, being approximately 950 fire assays per day. The assay department occupies the ground floor of the administration building and covers approximately 4,000 square feet of floor space. Ready access is had by motor truck and electric railway for the delivery of samples and the removal of crushed rock and rubbish. The combined weight of all sample rejects amounts to about 5,000 lb. per day, which is sent to the mill bins. There are six departments, each occupying a separate room-grinder room, fluxing room, furnace room, parting room, weighing room, and flux-mixing and storage room.

Jan 1, 1931

By T. Robson

"A multi-seam underground mining operation employing mechanized room-and-pillar methods provides 35 per cent of Smoky River's annual ROM coal production (2 million tonnes) from the Smoky River coal field. Surface mines provide the balance. Tectonic activity, which has resulted in deformed coal seams and a rugged relief to the area, has provided natural boundaries to discrete mining areas. Coal transportation to the central preparation plant incorporates a 3 km long underground conveying system. The company is committed to efficient resource recovery and a safe and healthy working environment. Introduction The Smoky River Coal operations (SRC) are centered in the Smoky River coal field located in west central Alberta, some 360 km west of Edmonton and 20 km from the Town of Grande Cache (Fig. 1). Combined mining operations produce 2 million tonnes per year run-of-mine coal from which 1.65 million tonnes of high quality, low volatile, coking coal are obtained. The underground mining operation, employing mechanized room-and-pillar methods, provides 35 per cent of SRC's annual ROM coal production (2 million tonnes). Surface mines provide the balance. Tectonic activity has resulted in deformed coal seams and a rugged relief in the area. This has provided natural boundaries to discrete mining areas. Background Exploration of the Smoky River coal field took place over four decades commencing in 1926. McIntyre Mines Limited (parent to Smoky River Coal Ltd.}, commenced development of the property in 1968 having secured a long-term contract for the delivery of coal to Japan. Production of underground coal at Smoky River commenced toward the end of 1969 and has been continuous on the property since that time. Originally, two underground mines were opened. Original planning envisaged the use of room-and-pillar techniques to develop blocks of coal for subsequent extraction by longwall retreat mining. Following initial development, two longwall units were established, the first in November 1970 in No. 5 Mine and the second in February 1971 in No. 2 Mine. Difficulties were experienced on both units, and production commitments could not be achieved. The longwalls were discontinued, and mechanized room-and-pillar was subsequently used for all underground mining."

Jan 1, 1985

By C. Caballero, M. Rosales, C. León, A. Valencia, R. Fuentes, A. Moyano

Slopping is the formation of waves in the converter due to the gas injection by tuyeres. Those waves produce a premature wearing of the refractory lining of the reactor due to its great amplitude. The affected zones are the tuyere line (outlet gas from tuyeres) and the front of this line. In the present work, a theoretical and experimental study is made to develop a theory that determines the variables involved in slopping, characterizing the more important parameters of operation in the phenomenon of slopping. In addition, this theory will allow for determination of new technological alternatives of the blast injection permitting to depress the slopping phenomenon.

Jan 1, 2007

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013