Search Documents

By Raymond V. Adolphson

The introduction of a new explosive component in 1955-56, called ANFO, featured much safer, effective blasting characteristics when compared to dynamite, accompanied by a notable reduction in cost. These savings mounted as borehole diameter or depth was increased with ANFO volume subsequently enlarged.

Jan 1, 1983

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By P. D. Katsabanish

Air decking applications are examined using numerical modelling and the AutodynTM code. The mechanism of damage is illustrated and discussed. Air decking is shown to provide advantages over stemming when powder factor is maintained. The current effort does not support reduction of the explosives column in favour of air decking. In a similar fashion, bottom hole air decking increases fracturing in the area of the air deck, compared to when the same volume is occupied by inert materials; however air decking does not appear to reduce the requirement for subdrilling. The apparent discrepancy between the numerical results and some field observations reported in the literature is discussed.

Jan 1, 2005

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By Richard W. Watson, Julius Roth

The Bureau of Mines has recently completed a contract study of the hazards associated with surface mining.! Part of this effort involved an analysis of surface mining accidents associated with blasting activities. For this purpose, 71 reports of accidents investigated by the Bureau of Mines or the Mining Enforcement and Safety Administration (MESA), covering the period from 1962 to 1976, were collected and analyzed. In addition, blasting accident frequencies for the period 1973-1976 were extracted from the central computer files maintained by the Health and Safety Analysis Center (HSAC) in Denver, Colorado. This paper presents a preview of the findings, which are treated in more detail in the final report.

Jan 1, 1978

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent.

Jan 1, 1998

By David R. Holberg

In the Kansas City metropolitan area, mineable Bethany Falls Limestone occurs 80 ft below river level under the 700 acre Park College Campus on the north bank of the Missouri River at Parkville. For 20 years prior to this project various firms passed over this opportunity to mine this property for construction aggregate because of uncertain costs, financial risk, and the difficulty of constructing an entry tunnel. This paper describes the drill and blast construction, rock bolting, and shotcrete lining of a 750 ft. long, 15% declining grade, truck tunnel through several Pennsylvanian limestones and shales.

Jan 1, 1997

By Jim Daly

The word “Enron” has taken on a totally different meaning since its leaders were caught juggling the books, President Clinton’s reputation was destroyed not by what he did but by how he tried to cover it up, Martha Stewart spent time in prison for not being honest. Our society is tolerant of mistakes we humans make but has become very critical about what we do following those mistakes. The blasting industry is in a similar position. We have all heard the stories of the tree stump that came down through someone’s roof, of the windows that were broken, of the casualties that occurred when a blast was not properly guarded. What was done following these incidents? In the mind of the public, not enough.

Jan 1, 2007

By Jaime Huidobro, Mervin Austin

The effect on an explosive column of the sharp transient stress waves generated during the earlier detonation of adjacent blastholes is of paramount importance to explosives users. Some explosives will sympathetically detonate under these stresses. Others may suffer a transient desensitization, arising from a temporary increase in the density of an explosive beyond certain limits and persisting until the explosive mass relaxes back to the original density. Some explosives are so adversely affected by these stresses that the product suffers immediate and permanent loss of sensitivity. These effects can be clearly seen while blasting in tough conditions such as burn cuts or wedge cuts and in materials, such as coals, that propagate shock waves well.

Jan 1, 1992

By John C. Didlinger

How do you measure the highwall? Why do you even need to know the highwall measurement? Why is it important? The importance of this measurement is to help keep a level floor and to help control vibration. Nevertheless, since most of us are not mountain climbers, there must be a safe and easy way to make an accurate highwall measurement. So with these factors in mind, how do you make your measurement?

Jan 1, 1997

By Isaac E. "Chip" Harris

Any contractor who agrees to supply materials or to perform services for a sum, is well aware of the importance of proper pre-bid information. Being able to properly plan costs and methods results in profits that allow the contractor to prosper. The paper discusses procedures used in estimating pre-bid cost; in particular, drilling and blasting cost for highways, dams and general construction projects. It breaks cost down into five categories and relates them to a total estimate used in bidding and budgeting a construction project.

Jan 1, 1975

By John P. Ashby

Production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the amount of damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts.

Jan 1, 1980

By Douglas R. Burns

Complying with SARA-Title III and the Emergency Planning and Community Right-To-Know Act as a Non-Manufacturing Facility. As of August 23, 1988 non-manufacturing facilities storing end using chemicals which require MSDS (Materia1 Safety Data Sheets) must fi1e with SERC (State Emergency Response Commission), the LEPC (Loca1 Emergency Planning Commission), and the loca1 Fire Department a list or copies of all MSDS sheets with the Tier I and Tier II forms completed.

Jan 1, 1989

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Ali Kahriman

This paper presents the results of ground vibration and air blast measurements from tunnel blasting activities during the construction of the Beylerbeyi-Kucuksu waste water tunnel under a residential area in Istanbul, Turkey. Within the scope of the study, the blasting pattern of the tunnel was engineered using Tunnel2000 design software and field studies and measurements for evaluating the productivity and safety of shots were realized for 136 rounds. During the study, the advance of the tunnel, face condition, ground vibration, air blast and neighbours’ complains and comments after every round were observed and the tunnel pattern was improved. Finally, an empirical relation for this tunnel route was developed between scaled distance and maximum amount of explosives, to continue activities in a safe and productive manner.

Jan 1, 2006

By Richard J. Mainiero, Harry C. Verakis, John J. Mulhern

There are application in coal mines where it would be advantageous from a safety stand point to fire unconfined shots. However, the firing of mud caps (adobes) or other unconfined explosive charges in underground coal mines is not permitted because of the explosion hazards associated with methane gas and coal dust. Present safety regulations in Title 30, Code of Federal Regulations prohibit such Practices. Recently, MSHA proposed revised coal mine regulations for the approval and use of sheathed explosives for Public comment.

Jan 1, 1987

By Ruilin Yang

Techniques for the study of blast vibrations, such as monitoring, analysis, and modeling are often misused between near field and far field blast vibrations. This paper discusses the differences between near-field and far-field blast vibrations in terms of these techniques. A typical example of a near-field blast vibration problem is a blast vibration in the crest of a new highwall behind a cast blast. In such a case, the blast can be a couple of hundred feet long and the distance from the blast holes to a monitoring station may only be 100 feet or less. In this situation, the size or spatial geometry of the blast is not negligible compared to the distance from the blast to the vibration monitoring point. On the other hand, a typical example of a far-field blast vibration problem can be a quarry blast with a nearby residence house. In this case, the distance from the blast to the house may be several thousand feet. The size of the blast is less than a couple hundred feet long and negligible compared to the distance from the blast to the vibration monitoring point.

Jan 1, 2007

By Kristen R. Bingham

"Today, more than ever, drilling and blasting contractors are challenged to manage the ever-changing risks associated with blasting operations. New neighborhoods are encroaching upon mine sites and blasting projects are confronted with increasing scrutiny by permit issuing authorities and nearby residents disgruntled by new construction. The act of transporting explosives material to and from thejobsite is far from easy and trouble-free. At the same time, the pressure to stay in compliance with the growing number of government regulations continues to mount. While new tools and technology are appearing in the workplace to address some of these challenges, losses still occur. Can the datagenerated by this technology help drilling and blasting contractors make better decisions? While basic risk management principles are still applicable, do new tools and technology assist in the effort to prevent losses? What are the downsides? In this age of new technology, is face-to-face interaction still necessary? While technology is certainly a useful component in the drilling and blasting world, can it be helpful in defending claims?"

Jan 1, 2017

By Armin Iravani, Changping Yi, Matthias Wimmer, Daniel Johansson, Santiago Gómez, Håkan Schunnesson

Sublevel caving (SLC) is a mass mining method based upon the utilization of gravity flow of blasted ore and caved waste rock. Drilling and blasting are the initial and the major impact on primary fragmentation and later material flow characteristics. The heterogeneity of rock mass has a great impact on materials’ mechanical properties and plays a significant role in rock fragmentation by blasting. In this work, a numerical model for sublevel caving based on 3D Voronoi tessellations was developed to section rock mass into arbitrarily shaped regions for modelling the heterogeneous rock mass. A coupled finite element and discrete element method was employed to investigate both the fragmentation due to blasting and the gravity flow of ore in a heterogeneous orebody. In the coupled model, the caved waste rock was modelled with loose discrete particles while the orebody to be blasted was simulated with bonded particles. The detonation of explosives was described with a particle blast method and a finite element model was used to model the remaining orebody. The results indicated that the fragmentation at the upper part of the ring is coarse while it is fine at the lower part of the ring. The heterogeneity of rock mass induced some boulders after blasting.

Feb 6, 2023

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000