Search Documents

By Zhucheng Huang, Ronghai ZHONG, Tao Jiang, Jun ZOU

The method of reduction roasting and magnetic separation of low-grade, micro- fine disseminated refractory iron ore following granulation with coal produced unexpected success. Pellets of iron ore with diameter between 3 and 8mm were granulated with coal, bentonite and water. The raw pellets and reduction products were analyzed by scanning electron microscopy and x-ray diffraction. Results show uniformly distributed coal powders inside the pellets improved the kinetics of the reduction process and accelerated the reduction rate. Reduction time was higher at temperatures below 890℃, which resulted in the formation of substantial amounts of fayalite. When temperature was increased, micro- fine hematite was then quickly reduced to iron metal and the amount of fayalite decreased sharply. When pellets were reduced at 950℃ for 25min, reduction products with 56.73% metallization rate were obtained. After grinding and magnetic separation, a concentrate with 72.18% Fetot was obtained.

Jan 1, 2015

By Shengqin Zhang, Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery, Amr Abdelghany

A novel ironmaking process is under development at the University of Utah aimed at producing iron directly from iron oxide concentrate in a flash reactor. This process will reduce hazardous emissions and save energy. The kinetics of magnetite reduction with hydrogen was previously investigated in our laboratory in the temperature range 1150 to 1400 oC at large temperature increments (~100 oC increments). Due to the significant melting that occurs above 1350 oC, the reduction kinetics was measured and analyzed in two distinct temperature ranges of 1150 to 1350 oC and 1350 to 1600 oC (~50 oC increments). Experiments were performed using magnetite concentrate particles of different sizes under various hydrogen partial pressures and residence times. Reduction degrees of more than 90 % were achieved in a few seconds at temperatures as low as 1250 ºC. Different rate expressions were needed to obtain reliable agreement with experimental data.

Jan 1, 2016

By Yuzhe Zhang, Xiaodi Huang, Xinli Wang, Bowen Li, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng

The recycling of waste tires has been a big environmental problem. About 280 million waste tires are produced annually in the United States and more than 2 billion tires are stockpiled, which cause fire hazards and health issues. Tire rubbers are insoluble elastic high polymer materials. They are not biodegradable and may take hundreds of years to decompose in the natural environment. Microwave irradiation can be a thermal processing method for the decomposition of tire rubbers. In this study, the microwave absorption properties of waste tire at various temperatures are characterized to determine the conditions favorable for the microwave heating of waste tires.

Jan 1, 2015

By Enrique Roy Dionisio Calderon

O presente trabalho mostra a concepção de um modelo que permite gerar uma superfície de mínimo consumo de redutor (carbono) em Altos-Fornos. No seu desenvolvimento foram consideradas as condições de equilíbrio das reações de redução, os balanços de massa e de energia e parâmetros operacionais. Sua aplicação à redução em Altos Fornos é exemplificada para situações reais, baseada em banco de dados operacionais de uma usina siderúrgica. Foi possível, a partir de planos de corte nestas superfícies, gerar diagramas binários do tipo CR-RD (Consumo de Redutor-Fração de Redução Direta), com possibilidade de serem gerados “on-line” no processo. Dentre os resultados obtidos, destaca-se a identificação de inviabilidades termodinâmicas importantes do forno. Dentre elas o modelo permitiu, através de seus “outputs” gráficos, prever e acompanhar o fenômeno de “gelada de forno”, conferindo desta forma maior segurança operacional ao processo.

Aug 17, 2017

By Gustavo Nucci Franco

A indústria do aço passa por seu pior período no Brasil e as empresas vêm buscando soluções para minimizar custos e garantir as operações com menos recursos. Ponto importante nessa busca de ganhos potenciais, a Logística vem, assim, merecendo uma atenção especial. Este trabalho apresenta esforços da AM Juiz de Fora, em parceria com a Franco Arbeit Engenharia, para reduzir o tempo de permanência de veículos em sua unidade e, com isso, evitar custos com o pagamento dos novos valores de permanência. Para isso, foram utilizadas modernas ferramentas de Simulação em Computador para que as soluções mais adequadas pudessem ser implementadas com sucesso.

Aug 17, 2017

By Ulysses Forastieri de Matos

A injeção de combustíveis auxiliares pelas ventaneiras dos altos-fornos vem se mostrando, nas últimas décadas, como uma técnica de redução do consumo de combustíveis e conseqüente redução de custo de produção de gusa. Uma das últimas técnicas de injeção de combustíveis auxiliares pelas ventaneiras, utilizada por algumas usinas siderúrgicas integradas a coque, no Brasil, nos últimos anos, é a injeção de carvão pulverizado e gás natural simultâneamente, aqui chamada de co-injeção. O presente trabalho apresenta os resultados obtidos na utilização desta modalidade de injeção em escala industrial.

Aug 1, 2018

By Raquel de Carvalho Reis

A fosfatização é um pré-tratamento superficial que tem como principais funções: a lubrificação, proteção contra corrosão e proteção contra abrasão. Os metais fosfatizantes mais comumente utilizados são o zinco, manganês e o ferro, sendo o zinco o mais aplicado nas indústrias siderúrgicas, automobilísticas e de linha branca. Atualmente, grande parte das pesquisas relacionadas aos processos de fosfatização é referente ao fosfato de zinco, sendo escasso o estudo sobre fosfato de manganês. O objetivo deste trabalho foi estudar a cinética de formação da camada de fosfato de manganês em aços baixo carbono, analisando a influência do substrato na formação da camada fosfatizada. As análises foram baseadas na obtenção das curvas de ganho de massa, sendo caracterizadas por microscopia eletrônica de varredura. Os resultados indicaram que para o substrato constituído essencialmente de martensita revenida, uma maior quantidade de carbonetos resultou em uma menor taxa de ganho de massa, pois estes funcionam como sítios ativos no processo de fosfatização, fazendo com que exista uma maior densidade de núcleos.

Aug 16, 2017

By Sueli Aguiar Barros

A água utilizada para refrigerar grandes equipamentos de produção, tais como Alto fornos, Fornos do Laminador de Tiras a Quente, Trocadores de Calor das Laminações de Tiras a Frio é originada de diversas torres de resfriamento da Usina, denominadas CBR´s (Casas de Bomba de Refrigeração). A água refrigerada necessita de tratamento químico para proteger os equipamentos de corrosão, deposição e crescimento microbiológico. Este tratamento químico usualmente na CSN é obtido por uma empresa contratada fornecedora de produtos químicos e serviços nestes sistemas. Dentre os serviços destacam-se as análises físico químicas, monitoramento automático das dosagens, avaliação diária dos tratamentos, etc. Recentemente, em Agosto de 2014 houve o início do novo contrato deste tratamento nas nossas CBR´s, mudando-se o fornecedor, os produtos e a equipe de atuação nestes sistemas. Este trabalho visa descrever como foi realizada esta mudança, as dificuldades enfrentadas inicialmente e os ganhos obtidos com esta alteração do tratamento. Destacamos os ganhos no monitoramento em certos sistemas que anteriormente não era realizado, como nos Staves do Alto Forno 3 e os ganhos financeiros em relação ao tratamento.

Aug 17, 2017

By Christoph Aichinger

The optimization and improvement of a modern integral iron and steel works gets more and more difficult as each individual plant is already operated at its best efficiency and at the lowest operational expenditures. However very often the individual plants are considered as stand-alone units and there are losses and inconsistencies on interfaces and take over points, which could be avoided and by that improving the overall performance of the iron and steel works as a holistic unit. Primetals Technologies looked into this subject extensively in the recent years and is now ready to offer new tools and services in order to assist operators to find further potential for improvement in processes, which seem to be fully developed at first sight.

Aug 17, 2017

By Wanderson Endlich, Tarley Rezende Secchin, Ana Clara Bernabe, Jennifer Oliva Coronel, Danielle Duarte Bernardi

A ArcelorMittal Tubarão (AMT) possui desde o início de operação os recursos hídricos como uma das questões centrais na estratégia de sustentabilidade e estabilidade operacional para sua produção. A gestão hídrica na AMT, dentre outras ações, garante que 96,5% de toda a água captada na usina venha do mar. Além disso, possui investimento contínuo em reusos internos, busca de fontes alternativas de água e combate ao desperdício e vazamentos. A condução dessa gestão hídrica, contribuiu de forma significativa para atravessarmos em 2015, a pior seca que o estado do Estado do Espírito Santo atravessou nos últimos 40 anos. Todos esses esforços resultaram na redução expressiva do volume de água doce utilizado na AMT, reduzindo o consumo específico de 4,2 m³/t em 2014, para 2,5 m³/t em 2018. Como resultado de um plano robusto de gestão hídrica, um projeto arrojado e inovador, pioneiro no Brasil e primeiro do grupo no mundo será realizado na empresa, a planta de dessalinização de água do mar. Com investimentos da ordem de R$ 50 milhões, a unidade começará a ser construída em 2019, com prazo de conclusão em dois anos. Produzirá até 500 m³/h de água industrial para o sistema de água da usina, proporcionando uma importante fonte alternativa ao consumo de água doce.

Aug 1, 2019

By E. S. Forbus

A process for producing reductive bleach in-situ in kaolin slurries has been developed. The bleach is formed by mixing an iron sponge powder (-325M) with slurry treated with SO2. The process has been successfully demonstrated in production, and applied to several grades. The color, brightness, and viscosity of the bleached product is equivalent to or better than that of product bleached with commercial sodium hydrosulfite . The tested products can be bleached at a cost, which is 38-54% of those associated with the use of commercial bleach.

Jan 1, 1993

By James J. Scott

In the fall of 1976 the author started test work with Friction Rock Stabilizers in uranium mines of the West, principally in the Ambrosia Lake and Churchrock districts of New Mexico. Tests were also conducted in other uranium mines in the Rocky Mountains area. These mines are plagues with problems in ground control due to the weak formations in which mineralization occurs, mudstones, siltstones, weak sand, etc. For this reason, it is extremely difficult to obtain good anchorage for long periods of time with conventional mechanical roof bolts. Resin bolts give good anchorage but are expensive and, because of hole erosion and difficulties in installation due to inadequate equipment for mixing the resin and placing the rebar, they are not widely used. Field testing was also carried out in trona, limestones and hard and soft shale formations. The mechanism of the Friction Rock Stabi1izer support is discussed and pull test data presented for various rock types.

Jan 1, 1977

By B Wentzinger

This paper presents the results of state parameter estimates in an active coal boiler ash storage facility using the most recent methods currently in use for cone penetrometer interpretation. State parameters estimates are also compared with the critical yield stress ratio approach, which is proposed as an additional liquefaction potential screening method. Recommendations are provided regarding additional in situ tests and laboratory tests that may be undertaken to improve the state parameter assessment and data produced for use in subsequent stability or liquefaction studies.

Jul 1, 2021

By D Reid, A Fourie, J Ayala

This paper discusses cone penetration test correlations for loose gold tailings that were developed within a critical state soil mechanics framework. The development of a new calibration chamber for cone penetration testing that consists of a modified triaxial cell is described. Some of the early development and commissioning issues that were encountered, as well as the solutions adopted are outlined, including the system to prepare the samples and to acquire high-quality data from the testing. Also, the triaxial laboratory testing required to achieve the critical state line is described, including some of the basic precautions considered necessary as good practice. Additionally, the system adopted for volume tracking of the calibration chamber sample is described, which is essential for ensuring a reliable state parameter comparison against the acquired cone penetration test data. Finally, some laboratory test data from the calibration chamber is plotted against the soil behaviour type charts currently available from various authors.

Jul 1, 2021

By Mahesh Hingorani

Integrity issues for bored cast-in-situ piles have raised the need for the use of non-destructive tests to verify pile integrity and detect possible anomalies in installed pile sections that could adversely affect their serviceability. Integrity inspections performed after installations are often the most reasonable alternative available to assess the shaft quality. The two most common methods are pulse-echo from a small hand held hammer at the pile top, and cross-hole ultrasonic transmissions along the shaft between parallel sonic pipes. While different in technique, each method has its advantages and limitations. This paper emphasizes more on the degree of accuracy of low-strain pile integrity test by comparing the results with cross-hole sonic logging. Reliable data collection and interpretation by an experienced test engineer will reveal the integrity of the pile. Cross-hole sonic logging and low-strain pile integrity testing were both specified as quality control measures for a metro rail project in India. Both cross-hole sonic logging and low-strain pile integrity testing indicated defects in several bored piles. Also minor imperfections recorded by cross-hole sonic logging were observed in low-strain results. The observations of the two test methods are presented and compared for a better understanding of the importance of low-strain test results for any project. INTRODUCTION Cast-in-situ concrete piles are often chosen as a deep foundation alternative where challenging soil conditions exist. Although quality control measures are almost always taken during the installation of the piles, it is often difficult or impossible to confirm the integrity of the pile at this stage, particularly in wet conditions. Because of the relatively high probability of bored piles having anomalies, quality assurance of each bored pile is essential for each project.

Jan 1, 2019

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

By Mark Kuchta

A new database application for long term production scheduling has been developed for LKAB's Kiruna mine. The scheduler uses a new block data structure whereby the monthly production data for three raw ore products are predetermined on a month-by-month basis for each production area that could be mined within the schedule time horizon. The production schedule is created by assigning the starting dates to the each production area subject to various mining operational constraints such that that the monthly deviations for the production targets are minimized. The system is well integrated into the mine's overall computerized mine planning system.

Jan 1, 2002

By Björn Lindquist

Boliden has developed a number of specialised technologies for smelter gas handling and effluent treatment. These technologies will be described. Special attention will be given to the high-pressure venturi, Editube wet electrostatic precipitator, mercury removal processes, and two-stage effluent treatment.

Jan 1, 2002

By Mike Smith, George Chung

"A 23 million dollar Flotation Plant has been commissioned at the Iron Ore Company of Canada in 1998. Nine OK-50 cells &re used to float silica in this 1,400 tomes per hour plant. The paper details project development, construction and operating results. This plant gives IOC the capability to produce not only high quality blast furnace pellets of varying silica, CaO and MgO levels, but also a high iron, DR grade pellet. The first activity was simply to sit down with the suppliers, Outokumpu, Wemco. GL&V and Svedala, to discuss applications and share experiences. We learnt what each supplier had to offer, what features would particularly suit this application, what options were offered, what were the materials of construction, how the equipment is maintained, which wear parts require replacement, etc., etc. We tried to learn as much about the equipment as the suppliers themselves knew. Then we tried to learn more: we contacted users and asked about any weak points, which options were worth incorporating and which items were not. We then discussed these points with the suppliers and established how potential problems might be overcome."

Jan 1, 1999