Search Documents

By Barry Olson

The Peñasquito deposit in Mexico is one of the largest grassroots precious metal discoveries to be developed in recent years. Goldcorp Inc. acquired the gold-silver-lead-zinc property with the acquisition of Glamis in 2006. The company has since committed US$1.5 billion to construct the mine, mill and associated facilities. The first of two 50-kt/d (55,000-stpd) mill and flotation lines is currently being commissioned while engineering and construction continues on the second line. A high-pressure grinding roll (HPGR) will ultimately take total throughput to 130 kt/d (142,000 stpd). The Peñasquito property is located in the northeast corner of Zacatecas state, Mexico. The elevation of the property averages 1,900 m (6,200 ft) above sea level and it is situated in a wide east-west valley. Except for one small outcrop (Peñasquito), the area is covered by up to 30 m (98 ft) of alluvium.

Jan 1, 2009

By Mohammed Sakr

A Two-Section Helical Pile (TSHP) is a steel pipe with two shaft sections of different diameters and with one or more helix plates near the bottom of each shaft section. TSHPs are used regularly in western Canada as foundation pockets for single and double circuit distribution power line poles. The results of a comprehensive lateral pile load test program and the field monitoring of TSHPs installed in organic soil (muskeg) over soft clay are presented in this paper. A total of nine full scale lateral load tests were carried out, including seven tests using TSHPs with different diameters and embedment depths, and two tests using one-section helical piles. The prime objective of the study was to evaluate the lateral resistance of TSHPs installed into very soft organic soil (muskeg) overlying soft clay soils, to compare their lateral resistance relative to one-section helical piles and to compare the measured and the estimated lateral resistances using p-y curves. In order to provide sufficient soil data for analysis, the subsurface soil stratification was evaluated using two different techniques including; Cone Penetration Tests (CPT) and Portable Soil Probe Tests (PSPT). The two testing techniques were also compared and evaluated. This paper summarizes subsurface soil conditions, pile configuration, helical pile installation procedure, testing setup and results.

Jan 1, 2009

By Sumantra Mandal

The hot deformed microstructure of the 15Cr-15Ni-2.2Mo-Ti modified austenitic stainless steel (commonly known as alloy D9) was investigated employing electron backscatter diffraction (EBSD). Hot compression tests were conducted in a Gleeble thermo-mechanical simulator at temperatures of 1173K-1373K (in steps of 100K) with a strain rate of 10 and 100 s-1 to different strains. Various kinds of deformation patterns were observed inside the deformed grains. These were inferred as the development of geometrically necessary boundaries or formation of parallel set of micro-bands. Recrystallized grains were partitioned from the deformed grains employing grain orientation spread approach. Extent of dynamic recrystallization (DRX) was found to be minimal at 1173K. DRX was predominantly found to happen at and above 1273K which increases with increase in strain. DRX nucleation and development mechanisms were discussed with respect to bulging of the parent grains and sub-grain rotation. Special emphasize is given on the role of annealing twins on DRX nucleation and subsequent expansion.

Jan 1, 2009

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

This paper sets out to consider a specific type of corrosion protection system, which is referred to as a Duplex Coating system. The dictionary describes a duplex system as consisting of two elements or a “twofold” composition. The duplex system described in this presentation is such a two-part corrosion protection coating, viz, hot dip galvanizing as the firm base or primer, followed by a top paint system designed to combat severe corrosive environmental conditions encountered in nature. In principle, the duplex system is a cost effective and balanced, designed coating that is suited to the environmental conditions and service life requirements.

Jan 1, 2009

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By John Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has collected pillar and span data at 34 stone mines in 10 states to develop pillar and roof span design guidelines for underground stone mines. Pillar, floor and roof conditions each contribute significantly to the overall mine stability. The roof may be stable for a century, or it may appear to be stable but fail with little warning. Clearly, an assessment of the mine roof is critical to the safety of these operations. However, up until now, the assessment of the mine roof came primarily from exposures in roof falls or portal areas. This provides only limited information, and a more proactive approach is needed to assess changing mine conditions. A separate effort was undertaken to examine the roof structure with the use of a borescope. Numerous physical and geologic roof structures were observed with a stratascope/borehole video camera. The objective of this work was to develop a technique of assigning numerical values to features seen within the mine roof and apply those values to formulate a roof stability evaluation. Such features as changes in color, grain size, and general lithologies are readily observed. Minor structures in the rock, fossils and fractures are also readily identified. Each feature may have a variable and site-specific impact on roof quality. A number of mines were visited and a series of holes were borescoped in each mine. The features identified in the roof were classified and potential for roof damage related to each feature was assessed. A process is presented that relates the structures and their locations to provide a numerical value, or roof quality index that can be used to assess roof stability.

Jan 1, 2009

By G. Lipsett, S. Dessureault

Information technology (IT) initiatives in the past have tended to be sold on their ability to maximize resource output and return on capital by allowing assets to be used more effectively and efficiently. Many IT projects fail, not delivering return on their investment. This is known in the IT industry as the “productivity paradox,” where increasing investments in IT do not result in comparable increases in productivity. Experiences and studies of most business sectors reveal that this paradox is rooted in the false assumption that more IT spending automatically results in financial benefit, whereas the benefits are in how effectively IT is used. Most business sectors have accepted that re-engineering of processes is required to gain the full benefits promised of IT. A mining operation has organizational processes similar to most business sectors, but unique operational processes. The lessons of changing business practice in more common business processes, such as inventory control and customer-supplier relationships, can be adequately transposed into a mine setting. The unique operational processes in mines, in turn, require unique redesign efforts. Several enabling information technology opportunities have recently become available, such as more integrated mine production management systems and tactical manager training simulators. This paper reviews some of the latest IT products and outlines the processes and kinds of change that will be required in order to benefit from these new investment options.

Jan 1, 2009

By Sergey Shabala

Green leaf tissues convert solar energy into the energy of chemical bonds of sugar molecules during the process of photosynthesis. The efficiency of this conversion can be much higher than efficiency of any of the currently known silicon-based solar panels. Importantly, vast amounts of CO2 are assimilated during this process. The efficiency of photosynthesis is critically dependent on the availability of a large number of nutrients, among which metal cations such as K, Ca, Mg, Cu, Zn, Fe, Mn, and Ni play a key role. In this paper I summarize basic requirements and major functions for each of these essential nutrients in plant photosynthesis, both at the whole-plant and molecular level. I will talk about how these requirements may be affected by the global climate trends and discuss the prospects of creating artificial photosynthetic “bioreactors” for efficient energy conversion and CO2 assimilation.

Jan 1, 2009

By Hector Carreon

This paper presents experimental data for the magnetic field produced by thermoelectric currents around uncracked hard-alpha inclusions in a Ti?6Al?4V specimen under external thermal excitation for different nitrogen content ranging from 1.6% to 5.9%. According to our preliminary results, the magnetic flux density measurements were found to be rather sensitive to changes in nitrogen content with the exception of the intrinsic material background magnetic signal that affected deeply the detectability of inclusions and imperfections in non-contacting thermoelectric measurements. Hopefully, these preliminary results can help identify a non-destructive test method that can detect material inclusions with a level of nitrogen that could be detrimental to Ti?6Al?4V alloy components.

Jan 1, 2009

By Chuanyu Feng

In this paper, a load-based micro-indentation technique suitable for field applications was developed. This technique bears the same theoretical background as traditional load-depth sensing indentation, and does not need any direct measurement of indentation depth or contact area. The removal of this requirement will reduce much of the cost associated with traditional instrumented indentation. To demonstrate the feasibility, a portable indentation system suitable for online material characterization was developed. Design issues of the portable unit were discussed and preliminary results using the portable unit were also presented.

Jan 1, 2009

By P. N. Anyalebechi

A comparative study of the mechanical properties of automotive steering knuckles produced by three different shape-casting related processes has been conducted. It involved the characterization of the tensile and fatigue properties of aluminum alloy A356 knuckles produced by the vacuum/pressure riserless casting (VRC/PRC), pressure counter pressure casting (PCPC), and the hybrid Cobapress (a casting-forging) processes, in accordance with the appropriate ASTM standards. Surprisingly, the knuckles produced by the hybrid Cobapress process exhibited the lowest strength. For example, the average 0.2% yield strength of the Cobapress knuckles was 31 MPa and 40 MPa less than that of the VRC/PRC and PCPC knuckles, respectively. However, between stresses of 150-200 MPa, the fatigue lives of the VRC/PRC, PCPC, and Cobapress knuckles were comparable. But above 200 MPa, the Cobapress knuckles exhibited the lowest fatigue life. The observed differences in the mechanical properties are attributed to the inherently different microstructures of the different knuckles.

Jan 1, 2009

By Shadia J. Ikhmayies

Polycrystalline CdTe thin films were prepared by vacuum evaporation on glass substrates. The I-V plots which were linear were used to find the resistivity. A value of 2.10×106 .cm was obtained. The transmittance was measured in the wavelength range 400-1100 nm. The bandgap energy was found to be 1.48 eV. X-ray diffraction pattern shows that the material deposits in the zinc blend structure with one strong reflection from the C(111) plane. The scanning electron microscope image shows a uniform surface with a small density of large (mµ1£) grains scattered on the surface.

Jan 1, 2009

Rio Tinto Iron Ore (RTIO) manages eleven mines in the Pilbara region, Western Australia. Three of these mines have previously or are currently mining black shale that contains varying amounts of pyrite. Several new deposits currently being evaluated and existing mines that may progress below water table in the future, will also encounter this waste material. The black shale presents not just an acid rock drainage risk but also a spontaneous combustion risk. This paper presents the black shale management strategy and provides an overview of the relevant activities undertaken by RTIO. The strategy can be divided into two components which firstly involve defining the risk and secondly involve managing the risk. The mineral waste management plan is used to identify specific mineral waste hazards by:geochemical characterisation of waste material,undertaking mine site specific risk assessments,characterising the receiving environment,identifying sulfidic boundaries in geological and mining models,quantifying the amount of sulfidic material in medium and long-term mine plans, anddesigning and sequencing black shale waste dumps. Once a mine exposes black shale the Spontaneous Combustion and Acid Rock Drainage management plan is used and the major activities are: regular site meetings with a representative from every group that works with black shale;compliance with safe working procedures for site specific and detailed activities;regular training;the use of specific explosives to prevent premature detonation;ongoing geochemical characterisation;acid water management, monitoring and analysis;regular internal and external auditing of procedures and practices; andclosure planning assessments and preparations (ie cover trials, geochemical void modelling, geochemical waste dump modelling). The success of this holistic strategy is evident by the awareness of personnel within the business, thorough understanding of the geochemistry and by undertaking proactive management of black shale during mining. The strategy and management plans adopted by Rio Tinto Iron Ore have activities that other mine sites with potentially acid forming material may like to consider implementing.

Jan 1, 2009

By P A. Tilyard

There have been enormous changes in mineral processing in the past four decades. For example grinding mill power has increased by an order of magnitude, regrinding is done to -10 microns and flotation machines are 100 times bigger. Operating staff have unprecedented opportunities for online monitoring and performance control of mineral processing plants. Sophisticated instruments can provide a plethora of data characterising the mineralogy and surfaces of particles. Digital computers allow complex calculations on huge amounts of data including modelling and simulation of machine and plant performance. However, all these changes have not necessarily lead to better metallurgical results. An analogy can be drawn with the thoroughbred racing industry in Australia. Significant advances in scientific knowledge in animal genetics, physiology, biomechanics and nutrition applied to the business have resulted in only a two per cent reduction in winning times for the Melbourne Cup and Caulfield Cup since the 1920s. A critical look at some mineral processing metrics suggests similar failures to improve performance despite putting in more resources. In fact certain parameters such as operating times and plant start-up performance are considered to have remained static or even deteriorated. There has been an emphasis on 'process' at the expense of 'outcomes'. The industry's strength has been in finding technical (or 'hardware') solutions while its weakness has been at the people end of the business in maximising and consolidating the gains from the technologies. Some trends in plant design over these years have exacerbated the apparent deskilling of operating and technical staff. Despite unparalleled options for communications, some staff are embarrassingly uninformed about technical developments in their fields. The 'boom and bust' cycles of the industry, together with trends in tertiary education and the effects of fly-in, fly-out (FIFO) operations, raise serious questions about the sustainability of human capital in the mineral processing sector. This paper by two experienced mineral processing engineers, with contributions from other senior practitioners, reviews these trends. While there may be an element of 'the older we are, the better we were', it is an attempt to identify the issues and propose solutions.

Jan 1, 2009

Many young mining engineers do not consider consulting as a possible job, believing that many years of working on-site is required to achieve practical experience, develop expertise and acquire industry contacts. However, mining consultancies employ engineers with varying levels of experience, including part-time university students, graduates and engineers who are relatively new to the industry. This paper outlines the role of a young engineer in a large mining consultancy and the benefits to both the consultancy and the client of having a mix of consultants with a diverse range of experience. From the authorÆs perspective, the work experience, lifestyle and rewards of mine consulting are compared to site based work, including a discussion on whether consulting is able to offer the professional development that a young engineer needs.

Jan 1, 2009

Since the days of Adam Smith and Milton Friedman the discussion of corporate citizenship and sustainability has been flooded with multiple contradictions, with proponents of sustainability saying that it is a crucial cog in the business strategy, while those against, maintain that æthe business of business is businessÆ and therefore sustainability issues are just add-ons. Sustainability arises from a deeply held vision by corporate leaders that businesses can and should play a role beyond just making money. Businesses should embrace the understanding that everything that a company does has an impact both internally and externally (communities, employees and customers), and the natural environment. This paper highlights the approach that led to a view that there is a contradiction between profitability, sustainability and community development, and we provide a further argument to the contrary. This argument is based on a comprehensive literature review of over three decades by various scholars linking corporate social performance and corporate financial performance. Driefontein Gold MineÆs approach is that of linking the community development, natural environmental and employee well-being initiatives and projects to the mineÆs business strategy. The paper further highlights the coordination and implementation mechanism of sustainability at the mine where the accountability lies with the head of the mine operations. A two pronged approach is employed where there is an internal dialogue on sustainability between the various departments coordinated by the sustainable development department and an external tri-sector partnership with local government, interested and affected parties and the mine. These approaches are closely linked to the contributions towards the mineÆs financial bottom line.

Jan 1, 2009

People in economically developed societies demonstrate inherent human care for Earth and want to stop pollution. Yet efforts to clean Earth seem bogged in confusion from wildly contradictory and alarmist predictions of æclimate crisisÆ. Supposed experts openly disagree yet weÆre told thereÆs universal agreement humans are causing æthe end of life as we know itÆ. The turmoil combines with peopleÆs feelings of fear, guilt, anger, hopelessness and even resignation and apathy to trigger æclimate alarmÆ. The paper enables people to rediscover clarity, hope and support for Earth by understanding how climate alarm and confusion were created and how they actually increase pollution. Many people seem to think global warming is as serious as pollution and worry that questioning alarm will enable pollution. Yet theyÆre different. We need be even more concerned about climate alarm because history shows repeatedly that when buried by ignorance and panic real problems grow overwhelming. Environmental credibility is endangered by confused politicians and sensationalist media. When weÆre willing to re-evaluate what weÆve been told we replace fear and confusion with facts and freedom to identify opportunities. Combining this with practical understanding of human behaviour and leadership enables opportunities to be identified and action taken. The paper shows how confident, informed leadership leads and supports higher productivity and effective care for the natural environment.

Jan 1, 2009

By J OÆDriscoll, R Butler, L Winter

The iron ore mining district of Labrador West and adjacent Quebec is Canada's largest iron ore producer with almost 50 years of production. The area is currently experiencing a period of renewed activity not seen in decades that includes new mine development, mine expansion and exploration for new iron ore resources. All of the past and present production and exploration programs in the district are centred on the Lower Proterozoic Superior-type iron formations of the Knob Lake Group, located within the Grenville tectonic province of the Canadian Shield. The Knob Lake Group is a continental margin sedimentary sequence which was deformed and subjected to greenschist to upper amphibolite facies metamorphism during the Grenville orogeny. Regional deformation and metamorphism plays a key role in making the iron formation of the Knob Lake Group economic. The distribution of orebodies in the district is controlled by superimposed F1/F2 synclines which causes thickening of the iron formation through repetition. Ore mineralogy consists of specular haematite, magnetite and locally martite with quartz as the major gangue mineral. Regional metamorphism has caused an increase in grain size of the ore minerals making it more amenable to concentrating and pelletising. Altius has been active in Labrador West since 2003 and is now the second largest licence holder in the district with several iron ore exploration projects. The Kamistiatusset project is located in the heart of the region's transportation, power and mining infrastructure. The property has seen limited previous exploration, but covers several significant iron ore prospects. Work by Altius includes a helicopter-borne magnetic survey, ground magnetic and gravity surveys, geological mapping, sampling and 6000 m of diamond core drilling all of which confirm both a favourable geologic setting and ore mineralogy.

Jan 1, 2009

In view of the increasing environmental regulations that have been promulgated all over the world in the last 30 years, non-ferrous smelters and refineries have learnt and adapted to treat effectively metals'-containing process waste streams that need to be bled from the plant. However, anions such as sulfates, chlorides and fluorides-presently not a major problem ?are coming under increasing scrutiny and need to be addressed in the near future. The current paper reviews options for waste water treatment with reference to: a) types of waste streams processed b) process chemistry c) discharge options d) recovery and reuse of water and e) solids disposal. Methods to obtain zero liquid discharge ?a possible solution to eliminate discharge of above anions and residual heavy metals- are discussed with case studies. The long term goal of any non-ferrous smelter plant should be to have a zero liquid discharge philosophy-an approach that would become an epitome of water reuse and conservation.

Jan 1, 2009