Search Documents

By Md. Nafiul Haque, Murad Y. Abu-Farsakh, Chris Nickel

"This paper presents the results from a pile load testing program for a bridge construction project in Louisiana. The testing includes two 54-inch open-ended spun cast concrete cylinder piles (OECP), one 30-inch open-ended steel pile (OESP), and two (30-inch and 16-inch) square prestressed concrete (PSC) piles driven at two locations with very similar soil conditions. All the test piles were instrumented with vibrating wire strain gauges to measure the load distribution along the length of the test piles and the skin friction and the end bearing were derived from strain gauge measurements. High strain dynamic load tests (HSDLT) were performed on all test piles at different times after pile installations to quantify the amount of setup with time. Static load tests were also performed on the PSC and open-ended steel piles. Due to expected large pile capacities, the statnamic test method was used on the two open-ended cylinder piles. The pile capacities of these piles were evaluated using various CPT methods (such as Schmertmann, De Ruiter and Beringen, LCPC, COFS methods). The result showed that all the methods can estimate the skin friction with good accuracy; but not the end-bearing capacity. Setup was observed for all the piles, which was mainly attributed to increase in skin frictions. The setup rate parameters “A” [The “A” parameter is defined as the rate of increase of pile capacity ratio (Rt/Rto) per log cycle of elapsed time] were back-calculated for all the test piles and the values were between 0.31 and 0.41.INTRODUCTIONDue to greater efficiency (capacity to weight ratio) of the pipe piles, open-ended piles are a viable option to solid piles. However, the behavior of open-ended piles is more complicated compared to the close-ended piles owing to possible formation of “soil plug” inside the open-ended pile. Many researchers have analyzed the behavior of both types of piles for different purposes; however, very few studies in the literature offer the side-by-side comparison of the close-ended and open-ended piles."

Jan 1, 2017

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

By Gerald H. Luttrell, Mohammad Rezaee, Roe-Hoan Yoon, Rick Q. Honaker, Aaron Noble, Abhijit Bhagavatula, Michael J. Kiser

A field study was undertaken to experimentally measure the concentrations of rare earth elements (REEs) contained in the process streams generated by a group of 20 coal preparation plants located in the eastern USA. For each site, representative samples of clean coal product, coarse refuse, and fine refuse were collected. Each sample was then partitioned into preselected size and density classes by wet screening/sieving and float-sink testing. The resultant products were dried and subjected to laboratory analyses to determine ash contents and rare earth element concentrations including Yttrium and Scandium. A detailed analysis of the database generated by this exercise showed that coal-based products from these preparation plants contained significant quantities of rare earth elements. In particular, the coarse refuse streams currently discarded by the 20 plants examined were found to contain a sufficient tonnage of REEs to satisfy the current domestic demand for these important elements. The data also showed a strong positive correlation between ash content and REE concentration, which suggested that the primary association of REEs in eastern USA bituminous coal sources is likely within fractions containing inorganic impurities. This association was well described using a simple power equation relating ash content and REE concentration. The ratio of heavy-to-light rare earth elements was discovered to be significantly higher in organically rich fractions of clean coal, suggesting that mineral impurities intimately associated with carbonaceous matter have elevated concentrations of heavy rare earth elements. A similar trend was observed for a grouping of rare earth elements (Y, Nd, Eu, Tb, and Dy) that are likely subject to near-term supply shortages. Finally, the database showed that a linear correlation existed between La for many REEs of interest, although there were several notable exceptions for some high-value REEs (Lu, Pr, and Tb).

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By Xun Luo, Yi Duan

A field trial of by distributed optical fiber sensing (DOFS) technique was conducted at a longwall coal mine in Australia. This investigation was designed to assess the applicability of DOFS for microseismic monitoring in mining. The experiments used commercially available optic fiber cables, geophones and associated data acquisition instruments – a fiber interrogator and a seismic recorder. The fiber cable was deployed in a 300m deep hole and in trenches of approximately 3.5 km long on the ground surface around and across the longwall panel being mined. The results obtained from the experiments have shown that DOFS is able to acquire microseismic data with quality that is comparable to geophones. It has been proven that DOFS can achieve higher spatial resolution for seismicity sensing and higher accuracy for locating events than a geophone network. These characteristics are particularly useful for using DOFS to monitor ground vibrations associated with ground caving processes and rock fracturing events induced by mining and civil engineering. It was also found that far more additional seismic events were recorded by the fibers than by the geophones. Automated data discrimination and processing methods must be developed in order to utilize DOFS for real-time applications.

Apr 26, 2022

By B Reid

"Since the commencement of mining operations at the Cowal Gold Operations (CGO) in 2005, reverse circulation (RC) drilling has been the preferred method for grade control (GC) sample collection. This method was selected because it allowed:for multibench drilling (20 m hole depths for two benches of mining) to aid mine planning increased data density for comparison against the wide spaced ore reserve model angled drill holes to intersect perpendicular to the strike and dip of the shallow dipping mineralisation ability to take two metre sample intervals to enhance the understanding of the mineralisation’s short-scale variability and provide the ability to flitch mine.From June 2008 to December 2013, RC GC was performed using a UDR rotary cone splitter. The field duplicate data over the period displayed strong precision, with a correlation coefficient of 0.94 and an average relative per cent difference (RPD) of 21 per cent for gold. Up to 66.1 per cent of field duplicate data greater than 0.1 g/t fell within ±20 per cent RPD. This is within limits of industry best practice. The Mine to Mill reconciliations over the same period showed the estimated GC grade was 7.7 per cent lower than the calculated head grade (CHG).In December 2013, the Progradex sampling system (PGX) was introduced at CGO due to its advertised ability to capture 100 per cent of the drill cuttings for the complete sample interval, inclusive of fines. Analysis of field duplicate data indicates that since the introduction of the PGX, the sample precision has drifted. From January 2014 to February 2016, the correlation coefficient was 0.92 and up to 51.2 per cent of field duplicate data, greater than 0.1 g/t fell within the ±20 per cent RPD. Over the same 26 month period, the Mine to Mill reconciliation improved to one per cent lower than the CHG. Granulometric analysis of the RC samples collected from the PGX indicated the fines material(<212 µm) averaged up to 22 per cent of the samples mass and following assay determination, the fines material represented a weighted average of 31 per cent of the total gold content within the sample.This paper highlights the:importance of the complete capture of all drill cuttings during an RC drill programinfluence of fines material on the sample quality and accuracyimpact sampling of the fines material has on the Mine to Mill reconciliation performancechallenges experienced in commissioning a PGX system.Citation:Reid, B, 2016. A Fine Looking Sample - the Importance of Fines in Grade Control Sampling to Mine to Mill Reconciliation, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 28–38 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Thomas Barczak

Roof support systems are designed for roof control to prevent unplanned falls. It sounds logical and has been the conventional thinking in support design since supports were first installed. In order to determine which support system should be used or which would be the most effective, the degree of control provided by the support system must be known. This question embodies the concept of a ground response curve, which is a measure of support control by assessment of the convergence in the mine entry as a function of the support capacity. In this National Institute for Occupational Safety and Health (NIOSH) study to optimize standing roof support design, ground response curves were developed for longwall tailgate conditions from numerical models of Pittsburgh Coal Seam geology. The models were calibrated against tailgate convergence measurements that were made in two Pittsburgh Coal Seam mines as the depth of cover varied during the panel extraction. Ground response curves were developed for four loading conditions: (1) development, (2) side abutment, (3) front abutment near the longwall face, and (4) full extraction inby the face. In general, the tailgate convergence and required support capacity increase through each of these loading stages. It was concluded that prior to failure of the rock mass, the support system regardless of its capacity has relatively little impact on tailgate convergence. Recognizing that the support cannot prevent much of the (pre-failure) convergence that is occurring is an important part of support design. Supports that exhibit high loading stiffness but cannot sustain that loading through a displacement compatible with the ground response curve will not provide adequate roof control because they can fail prematurely. The required capacity depends on the loading plus yielding characteristics of the support and the amount of rock failure that has occurred. The loading plus yielding character establishes where the support loading intersects the ground response curve. Design criterion for support capacity based on the identifying the onset of strain-soften rock response leading to ?damaged roof? is proposed as a foundation for assessing support design requirements. The capacity without accounting for the loading and yielding character of one support should not be used to assess the capacity requirement of an alternative support design, particularly when the loading and yielding characteristics are significantly different. A sensitivity study was made to evaluate the impact of mining height and overburden depth. As expected, the results show that convergence increases with increase in mining height and increase in overburden depth. Some specific support examples are also analyzed. Although this is a first step and the two-dimensional numerical models have limitations, these initial studies provide valuable insight into the control provided by the roof support system and will ultimately lead to optimizing support design based on specific mine site conditions.

Jan 1, 2008

By Russell Frith

A review of published literature reveals case histories whereby the entire periphery of a coal pillar has “burst” out as a single event during first workings, the associated energy and material release causing significant damage to adjacent roadways and any equipment/infrastructure located within said roadways. Such events are distinct from coal burst events during first workings such as that at the Austar Mine in 2014, or those linked to overburden bumps related to either horizontal stress-driven slip along major faults and/or thick, massive strata units in the overburden or floor of the coal seam.

By Stephen Mansfield

Analysing how accurately a blast design is implemented is one of the cornerstones of a successful operation, and critical for mine optimisation. This paper presents a concept that involves the collection and analysis of data for the five stages through which a blast transitions, from budget through to implementation.

Feb 1, 2020

Operating CIP/CIL gold recovery plants in the arid regions of Western Australia face unique challenges due to water and ore quality issues. The presence of cations of Mg, Fe and Cu metals in water supplies and leached sulphide ores can have considerable effect on plant consumption of lime and cyanide, due to pH buffering and complexation effects. Reagent costs are critical to many of these operations. In this paper, computational modelling is used to analyse a number of process options to mitigate such issues. This requires careful consideration of the chemistry of the process system, and the ability to predict accurately the response of speciation and precipitation reactions to changing process conditions. The Mg-Fe-Cu-CN-H20 system is specifically modelled in this application. The Gibbs Free Energy Minimisation thermodynamic framework has been selected to model equilibrium phenomena. Furthermore, this approach has been extended to the process flowsheet level, incorporating multiple unit operations and recycle streams in a steady-state mass balance model. The Gibbs equilibrium composition module of HSC Chemistry software has been successfully integrated into the commercial flowsheeting package SysCAD. Consideration of the Gibbs Energy Minimisation capabilities of other flowsheeting packages has also been given. This approach has been successful in simulating the aqueous process chemistry typical of such plants. It has resulted in a predictive capability where equilibrium states respond appropriately to process changes. Potential cost savings may be identified by examining alternative process conditions to minimise overall reagent consumption.This methodology may be extended to other hydrometallurgical plants where issues of solution ideality, temperature and other equilibrium processes are sufficiently understood.

Jan 1, 2005

By S Corbel, P J. T Donchak, W Gorczyk

The Hodgkinson Province numerical modelling project aims to develop an improved understanding of the physical conditions that lead to the localisation of goldbearing fluids within known systems and apply this understanding to the prediction of potential new sites of gold mineralisation. The project follows a series of stages from identifying the key parameters required to construct and test simulations through to reverse engineering of known deposits and ultimately applying the conditions identified in the preliminary stages to predictive simulations. Results of the modelling demonstrate strong geometric controls of the localisation of fluids during mineralisation. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By James P. Kimball

AMONG the curious results of the recent advance of prices in the iron trade of the United States, one of them at least is to be regarded as of great importance. I allude to the utilization of mill cinder as a cheap and almost costless substitute for high-priced iron ores in many blast furnaces, situated within easy reach of such raw material. It has been, with but few exceptions, the practice in this country, based upon tradition rather than upon authority or European precedents, to waste this material on 'account of its high proportion of silicic and phosphoric acids, although known to contain more iron than most ores, and although also known to be sometimes applied to the blast furnace in greater or less quantities without serious detriment to the iron for specific purposes. While in use to a limited extent in the Hocking Valley and Hanging Rock iron regions of Ohio for several years, its use in Western Pennsylvania has only become general of late, under the exigencies of high prices and a short supply of ore. Especially has mill cinder largely entered into the stock of furnaces attached to rolling mills in and about Pittsburgh. Under such circumstances the cinder pig has been paddled on the premises, and the malleable iron produced has been unexpectedly good. Cautiously as at first mill cinder has been applied, it is evident that the temptation to use it freely is a strong one whenever the commercial rates for high-class ores are out of proportion to the general conditions of the iron trade, as sometimes happens in this country, especially as the free use of it is apparently justified by the quality of the iron produced from this cheap and abundant material. Indeed the consumption of cinder pig has., not been wholly confined to mills using up the production of furnaces belonging to the same plant. One furnace at least on the Ohio, at Covington, for several' months has been making foundry pig from "all cinder." The iron has gone into the general trade. It is probable that malleable iron of good quality can he made from the poorest cinder pig, but with what degree of economy will

Jan 1, 1881

By K, J. MAUNDERS

This paper briefly describes a computerised model of the South African electricity system which has been developed jointly by the Atomic Energy Board and the Electricity Supply Commission. The results of an analysis of this system have been subjected to a fairly extensive sensitivity analysis which reveals that up to the year 1990 between 680 and 700 million tons of coal will be required for electric power generation, together with between 7 000 and 10 000 tons of uranium. This result is fairly insensitive to data variations, but the prediction of a cumulative requirement up to the year 2000, of between 1 300 and 1 800 million tons of coal and 25 000 to 70 000 tons of uranium, proves to be very data-sensitive.

Jan 1, 2014

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

"Mining used to be a business primarily focused on the technical aspects of getting valuable ore out of the ground and extracting the minerals efficiently. Without denying the importance of these skills, a narrow focus on technical issues is no longer enough to guarantee success when it comes to exploiting rare earth element (REE) deposits. Molycorp failed to enter the global REE market in a successful manner, while none of the many REE exploration projects has turned into an active mine so far and none is expected to commence operations in the near future. Accordingly, the world of REE is far more complex compared to other commodities. This paper looks into the REE industry to identify the factors that can connect potential U.S. REE mines to the market. The ability to break free from past thinking and become future-focused is a key driver. Mining of REE is pointless without a corresponding value-adding chain, while developing a value chain without first establishing an uninterruptible source of REE is also senseless. The mining sector must be based on the REE value chain and vice versa, along with the establishment of a market channel for the REE products that come out of the mine. INTRODUCTION It has been seven years since rare earth elements became the subjects of front-page headlines. It was when the controversial Chinese export policy for these critical commodities was epitomised in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al, 2016c; Mancheri, 2015). The world was dismayed, especially in REE-importing countries, such as the United States that was and is still totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand and the Chinese sovereignty of the REE-market on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016). The prices of REE, however, dropped rapidly and at the moment of writing this paper are in 6-year lows, at the level of the price average before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REE-market entrants (Barakos et al, 2016b; Rollat et al, 2016). Production cutbacks and industry consolidation in China impel REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 1, 2018

By Jens Gutzmer, Helmut Mischo, George Barakos

"It has been nearly eight years since rare-earth elements (REE) became the subject of frontpage headlines. It was when the controversial Chinese export policy for these critical commodities was epitomized in a maritime border dispute with Japan in September 2010 that resulted in the big REE crisis and price spike of 2011 (Barakos et al., 2016c; Mancheri, 2015).The world was dismayed, especially in REE-importing countries such as the United States that was, and still is, totally dependent on Chinese production and exports (Barakos et al, 2016c; Kennedy, 2015). The short-lived alarm initiated a treasure hunt by way of exploration for REE deposits all over the world. The continuously growing demand on the one hand, and the Chinese sovereignty of the REEmarket on the other, led the rest of the world to explore their own REE resources. In just a few years, more than 400 projects were initiated to explore REE deposits outside of China (ERECON, 2015; Goodenough, 2016).The prices of REE, however, dropped rapidly in late 2017 and were in six-year lows, before the 2011 crisis (Barakos, 2017). The viability of even major established producers is being challenged, not to mention the development prospects of potential REEmarket entrants (Barakos et al., 2016b; Rollat et al., 2016). Production cutbacks and industry consolidation in China have impelled REE market experts to forecast that prices have already reached their lowest point and have nowhere to go but up (Adamas, 2015; Roskill 2015). Yet, expectations for increased REE prices are limited and drastic changes are unlikely to happen in the near future, as there is still excess supply in the overall REE market (Barakos, 2017). Nevertheless, the low prices of rare earths are not the only reason that potential producers are struggling to enter the global REE market. Among other parameters, the separation process of the individual elements seems to be the most important factor, as it is technically challenging and expensive to build and to operate."

Jan 8, 2018

By S Saydam

Professional engineers need to be able to apply university learning to practice. In particular, they have to take responsibility for interactions between technical systems and the complex social environments in which they operate. The most effective way of building this competency is through active experiential learning. We have been developing an advanced educational integrated simulation system to provide mining engineering students with an interactive and immersive learning experience that is not otherwise possible. This will give students an authentic experience in working with industry software packages, while also contextualising the learning in terms of the broader and longer-term impact of technical decisions. We have been piloting the system, in undergraduate courses in order to establish its effectiveness in building systems thinking competencies for mining engineering. For postgraduate students and professionals, the same tools and methods can support studies of more challenging and complex scenarios where mining engineers have to place their decisions within complex global industry contexts.

Nov 22, 2011

By J A. M Luz, A T. Bernardes

HukkiÆs law is an empirical law, which does not take into account several events of energy loss during the fragmentation processes. Since experimental results are very difficult to obtain, for a large range of fragment sizes, the verification of the law is very difficult. The relation between fractures and fragmentation processes with fractal geometry was proposed some decades ago. Empirical laws known in this context show basic features of fractal geometry, mainly self-affinity and power law behaviour. Thus, in this work a model was developed to simulate the fragmentation process and to check the relation between energy consumption and fragment sizes. The model is represented on a regular lattice. Links can represent pathways for fracture processes. The events of fragmentation have energy given by a probability distribution function. In the model there is no mass loss. Propagation of fractures occurs as self-avoiding random walks on the regular lattice.

Sep 26, 2011

By M. J. Gagnon

The agglomeration of particulate materials is used in many mineral processes to enhance the settling of the fine particles, Depending upon many physical and chemical parameters, the aggregates demonstrate specific density-size distributions, In this study, a fractal model of the agglomeration process is introduced, Based on reliable experimental data and on physical calculation, the model presented helps to envisage the initial formation of the micro-flocs, and to interpret the subsequent interactions between the aggregates in terms of either coagulation or flocculation, Data from different sources, materials and different agglomeration processes are analysed and compared in the light of the proposed model.

Jan 1, 2005

By Jeremy Maurer, Duah Philip, Awuah-Offei Kwame, Donya Otarod

Land use impact assessment for mining is time- consuming and expensive. Because of mining’s impact on biodiversity, land use assessment methods that evaluate biodiversity are important for mining land use impact assessments. Remote sensing, in particular satellite multispectral sensing platforms such as Sentinel‑2 and the Landsat mission series, have been used to assess and quantify biodiversity through proxy variables such as NDVI (Peña-Lara et al., 2022). The objective of this paper is to present results of a comparative study of land use and biodiversity based on multispectral satellite observations and production data from copper and cobalt mining in the Democratic Republic of Congo. We quantify the relationship between different spectral bands and vegetative indices and the production data provided by the mining companies and measure correlations. The results suggest that remote sensing could be a cost- effective means of assessing biodiversity impacts of mining.

Feb 1, 2025