Search Documents

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By Don Novotny, Dana Spencer

In this workshop our intent is quite simple; that is that we will introduce a relatively new technology that may have applications in blasting applications. This technology is the laser initiation of explosives. This workshop course is not intended to suggest ways in which specific blasting problems can be resolved. That is the purview of experts within each of your fields.

Jan 1, 1994

By D S. Preece

The aim of the present work is to investigate the effects of shooting multiple explosive charges, in the same borehole, on the amplitude and frequency content of the generated seismic wave. The work also investigates the effect of the coupling medium used in the borehole on the quality of the generated seismic wave. The delay period between the shots is on the order of months and up to a year. The investigation utilizes a numerical modeling approach which is capable of modeling the detonation of explosives as well as shock and stress wave propagation in solids.

Jan 1, 2012

By David Allen Jones

A depleted county gravel pit was rehabilitated by contracting an artist to convert it into sculpture, rather than using traditional reclamation methods. The sculptor's ideas were generally implemented as designed, but problems arose because of a faulty survey and severe weather. Public reaction was critical. A design symposium was presented by retaining six artists to prepare designs for varied sites. A public forum was offered and video-documented for broadcast. A new art-reclamation project grew out of this project.

Jan 1, 1981

By Brandon Axelrod

This paper follows a student’s interest in explosives which began at an early age after watching a television program highlighting explosives engineering. The use of explosives in those programs led to curiosity about how one gets involved in the industry. These programs enticed the author to further investigate the explosives industry leading him to an explosives camp for high school students. After attending the camp, this passion further developed into postsecondary education.

Jan 1, 2015

By N Clarke, R Dineen, W Jones

The Mt Lyell copper mine in western Tasmania has discharged acid drainage (AD) into the Queen and King Rivers and Macquarie Harbour for over a century. Presently, dissolved copper loads of about 1000 tonnes per annum and dissolved aluminium loads of >2000 tonnes per annum are contained in the AD, which is derived from underground workings (~60 per cent) and historic waste rock dumps (~40 per cent). Flows vary from about 100 L/s during dry periods, to >400 L/s during the wet winter. The site is presently operated by Copper Mines of Tasmania (CMT) who are not responsible for the acid drainage generated from the mine site. Although western Tasmania is famous for its mining history, tourism and aquaculture have emerged as the new industries on the West Coast, with a major tourism railway (the Abt) recently opened along the banks of the Queen and King Rivers. The emergence of these industries in a æclean greenÆ Tasmania has resulted in a strong community and government push to remediate the acid drainage. Remediation investigations and efforts at Mt Lyell were initiated by the Department of Primary Industries, Water and Environment (DPIWE), previously known as DELM, in 1995, and have included the quantification of environmental impacts arising from the AD, and the investigation and costing of potential remediation options. A primary focus of the work has been to identify cost-neutral options which recover metals from the AD in a saleable form to help defray on going treatment costs. This paper summarises these activities in generally a chronological order, highlighting findings of the program that are potentially applicable to other acid drainage sites.

Jan 1, 2003

By J Temos

This paper outlines a number of immediate practical approaches to continuous improvement in environmental management in the minerals industry. It puts these into context with longer time-frame step-change approaches whose gestation may take a decade. Examples of improvements and approaches are drawn from WMC operations.

Jan 1, 2002

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By Ren G. Dong, John Z. Wu, Daniel E. Welcome, Kristine Krajnak

Although the exact mechanisms underlying vibration white finger (VWF) are not clear, it has been speculated that VWF is associated with variations of the blood flow patterns due to the physical damage and/or degeneration in neural and vascular tissue caused by vibration loading [1]. Excessive dynamic deformation of the soft tissues in the fingertip under vibration loading is believed to induce multiple occupation-related hand/finger disorders. However, the in vivo distributions of the dynamic stress/strain of the tissues in the fingertip under vibration conditions have not been studied because they cannot be measured experimentally to date. The goal of this study is to analyze, theoretically, the location and frequency-dependent dynamic deformation of the soft tissue in the fingertip during vibration exposures. [ ] Methods The fingertip considered in the model is the distal phalanx, the portion from the distal end of the fingertip to the distal interphalangeal (DIP) joint articulation (Fig. 1). The external shape of the fingertip was determined using a smooth mathematical surface fitting to the observed fingertip shapes. The fingertip surface was then scaled to the dimensions of a typical male index finger: length 25 mm, width 20 mm, and height 18 mm. The fingertip was approximated to be symmetric, such that only a half of the fingertip was considered in the FE modeling. The fingertip was assumed to be composed of outer and inner skin layers, subcutaneous tissue, bone, and nail. The soft tissues (inner skin layer and subcutaneous tissues) were assumed to be nonlinearly elastic and viscoelastic, while the bone, nail, and outer skin layer were considered as linearly elastic. The simulations were conducted using a displacement-controlled protocol in two stages. First, the fingertip was statically pre-compressed. The contact plate was first displaced towards the finger to achieve a predetermined value of tissue deformation (i.e., 0.5, 1.0, 1.5, and 2.0 mm). Second, the steady-state dynamics responses of the fingertip were analyzed using a linear perturbation procedure. The fingertip was subjected to a continuous harmonic excitation (magnitude 0.5 mm) from the contact interface. The dynamic analysis was performed in a frequency domain ranging from 16 to 2000 Hz. The frequency-dependent distributions of the vibration magnitude and dynamic strain magnitudes in the soft tissues are investigated. Results Typical simulation results for the frequency-dependent distributions of the vibration magnitude in the soft tissues are shown in Fig. 2 (figures show the results with a pre-compression of 2.0 mm). The vibration magnitude at the contact surface is 0.5 mm (specified) for all frequencies, while the vibration magnitudes in the soft tissues are location- and frequency-dependent. It is clear that the fingertip has a major resonance around 125 Hz, at which the vibration magnitudes in the soft tissues are over four times greater than that of the contact plate (0.5 mm). It is interesting to observe that, at this resonant frequency (125 Hz), the soft tissues at the tip has the maximal vibration magnitude while the regions near the contact

Jan 6, 2006

The authors describe two stratiform intrusions within a two miles thick ophiolite belt, one of the many ophiolite (serpentine) belts of the eugeosynclinal sequences of the Kalgoorlie System (metamorphic age c.2700 million years). Unusually good evidence of gravitational differentiation involving cumulates for an Alpine type peridotite-gabbro intrusion has been obtained, in spite of modifications of the original igneous rocks imposed by regional metamorphism. Unmetamorphosed relics of cumulate rocks are a surprising feature of this occurIfence.'fhe differentiation process reflected in the layered sequences is compared to that of the Stillwater Intrusion, Montana. Phase, cryptic and rhythmic layering are recognized. The economic significance of this study lies not only in the possibility of nickel mineralization in this ophiolite belt, but also in that much detailed information on the nature of these belts, which is difficult to obtain in the case of the more altered and sheared rocks of the belts carrying gold and nickel ore deposits nearby, is gathered from the Yilmia occurrences.

Jan 1, 1969

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By Bagley A. S

The accuracy and precision of rutile analyses are discussed. Comparison is made between the wet chemical and X-ray fluorescence spectrographic methods of. estimating Ti02 in commercial rutile. Various allotropes of 'I'i02 are identified by diffractometry and a comparative analysis of the coloured varieties of rutile is given. For X-ray fiuorescence . analysis, specimen preparation is critical and sample grinding and pressures. for pellet making are discussed in detail.Cellulose bonded and backed pellets are shown to be subject to relaxation with increasing age.INTRODUCTIONTo date much of the analytical work on commercial samples has been done by wet chemical methods.This led to various discrepancies in results, which are of particular importance when certificates must be issued for overseas shipments. The present work reviews the nature of rutile and compares the results of Ti02 estimation by wet chemical methods and those obtained by X-ray fluorescence spectrographic analysis.In the rutile industry the results from different analysts and even those from the same analyst are not always consistent. To the analytical chemist this should not be surprising.Fairbairn (1951) showed the results obtained from 34 different analysts on a specially prepared sample of granitic rock. It is of some interest to note that the Ti02 content as determined by the 34 analysts using unspecified methods ranged from 0-17 per cent to 0·30 per cent. Fairbairn (1953) found that1. replicate analyses from the same analyst give a high order of precision,2. analyses by different analysts using the same procedures give reasonable precision, and...

Jan 1, 1965

By Seong-Taek Yun, Chil-Sup So, Seung-Jun Youm

The greisen-bordered quartz veins are spatially, temporally and genetically associated with a late Cretaceous granite intruding an early Palaeozoic, limestone-rich formation. Paragenetic data indicate three stages of hydrothermal mineralisation, the first typically in or within 500 m of the granite stock and showing vertical zoning between deeper Mo and higher W, the other two more abundant in the upper and outer parts of the mineralised area. Fluid inclusion and stable isotope data indicate that hydrothermal veins formed over a temperature range of 120-395 degrees C from low-salinity fluids. Early wolframite and molybdenite deposition in stage I occurred at temperatures of 300-395 degrees C from magma-derived, low-salinity, CO2-rich fluid, mainly as a result of fluid boiling and associated CO2 effervescence. Progressively larger volumes of local meteoric water entering the system led to the successive deposition of scheelite in stage I vugs, stage II base-metal sulphides and stage III fluorite-carbonates. Remobilisation of W and its later deposition of scheelite in the outer and shallower portions of the system occurred at 215-275 degrees C and stage II and III mineralisation from lower-temperature fluids that became progressively lighter in stable isotopes. It is concluded that the influx of meteoric water increased with distance from the cooling pluton

Jun 18, 1905

By R. Patel, D. R. Taylor, P. M. Varley

In-situ measurements of ground stress were made from surface boreholes, using overcoring and hydrofracturing techniques, to obtain data for the detailed design of the underground works at Pergau. Unexpectedly low stresses were measured and appeared to correlate with apparent hydrofracturing observed during permeability testing. The low values of the minor principal stress had a major impact on design, particularly of the lining for the pressure tunnel and shaft. Additional hydrofracture tests were made underground during construction of the low- and high-pressure headrace tunnels and the pressure shaft, to define the vertical reduction in the minor principal stress with overburden. These data were then used to locate and design the steel and reinforced concrete linings

Jun 19, 1905

In the geologically prospective nations which rim the Pacific Ocean, mineral deposits offer great potential to create wealth for social and economic development. The paper first examines the geological and economic attributes of potential mineral wealth based on current outlook assessment of all significant base metal deposits discovered to 1988 in two Pacific Rim nations - Australia and Canada . The variability of mineral wealth among the economic deposits evaluated and the major contribution of the few world-class discoveries to total mineral wealth are highlighted. Then, the essential but too often neglected linkage between the makeup of potential wealth and its actual realization is analysed. The impact of taxation and the role of exploration are crucial in this regard. Finally, the ingredients of exploration success, prerequisites for realizing the mineral wealth of nations, are examined.

Jan 1, 1995

By R. G. Kidel, S. C. Doming

The project has shown that it is feasible for a junior company to reopen a narrow vein-style gold mine and successfully take it into production. An intimate understanding of the mineralisation and a flexible approach to mining are crucial, as are stringent cost control and efforts to keep overheads low. The project has confirmed the geological complexity of the Main Lodes, which consist of highly sheared quartz-sulphide infill in strongly sericitised granodiorite. The existence of discrete high-grade zones within the Hangingwall Lodes has also been confirmed. Broad low-grade zones continue to be recognised and require the local application of bulk longhole mining methods. The initial mine plan called for predominantly longhole stoping, but adverse ground conditions have meant that a switch to air-leg mining has produced higher run-of-mine grades. The excess capacity at the processing plant can best be used by batch processing, with its reduced maintenance requirements

Jun 21, 1905

By Tristan Worsey, Nathan Rouse

The Florida legislature allocated funding for the Florida State Fire Marshal (FSFM) to review the applicability of the United States Bureau of Mines (USBM) Report of Investigations (RI) 8507 blast vibration limits with respect to Florida and its soils. The study also discusses whether the current blasting vibration limits set by statute are still appropriate, including a review of measured vibration amplitudes and frequencies, structure responses, and theoretical analyses of material strength and strains

Jan 1, 2019

By R. B. Krog

The use of belt air as an intake source at longwall operations has greatly changed over the past decades. The practical considerations for the use of belt air are controlled by a variety of factors including airflow quantity and velocity, coal methane content, methane desorption rates, coal mining rate, belt length, stopping leakage, and the number of gateroad entries. At longwall operations, the advantages and disadvantages of belt air are different for gateroad development and longwall panel extraction. During gateroad development, the use of belt air to ventilate the working section will reduce the leakage from the intake to the belt compared to the belt air being ventilated outby the working sections because of lower pressure differentials. A greater quantity of airflow will reach the last open crosscut with belt on intake than outby, given the same amount of pressure and airflow available at the mouth of the section. This paper will investigate the current ventilation practices regarding the use of belt air during gateroad development and longwall panel extraction. Operating considerations regarding air quantities and pressures to deliver the required airflow will be investigated using ventilation network modeling.

Jan 1, 2009

By P. J. Bhonde, R. D. Angal

Conventionally low carbon ferromanganese is manufactured globally by refining high carbon ferromanganese in liquid state. This process is an expensive and lengthy technique. Hence, the present work was undertaken with the objective of understanding the feasibility and kinetics of the solid state refining of ferromanganese. The process involved transformation of carbon rich carbides viz. Mn3C2, Mn7C3 into metal rich carbide i.e. Mn15C4, Mn23C6 by subjecting the alloy powder to a flowing stream of carbon dioxide. Effect of the process governing parameters such as time, temperature, particle size, pressure on the extent of decarburization was studied. Without any loss of manganese in the form of fumes or slag, it was observed that, there was substantial reduction, viz. 65 per cent in the total carbon content, by this technique. Subsequently, the process was investigated to find out the mechanism of carbon removal. Depending upon the temperature and the particle size, it was found that the rate controlling mechanism changes from chemical reaction control to product layer (ash) diffusion control. The activation energy for each of the aforesaid mechanism was computed. The values thus obtained substantiated the aforesaid mechanisms.

Jan 1, 2004

By GA Harrison

The introduction of Extra Low Profile (XLP) mechanised equipment within Anglo Platinum is aligned with the overall New Mining Technologies strategy to focus on continuing modernization of our mining operations to achieve injury free sustainable production and cost effective mining technologies. The method allows for the introduction of a suite of XLP and Low Profile (LP) equipment in a narrow reef (1,2m) mining environment. For the first time it is now possible to achieve total trackless mechanisation at these stoping widths and XLP Breast mining has the potential to add more value when benchmarked with conventional mining and other mechanised methods. Various types of XLP equipment were tested at different sites within Anglo Platinum and this paper describes the XLP equipment evolution to-date. It concludes with recommendations on our future strategy regarding implementation and roll out of the XLP technology within Anglo Platinum.

Jan 1, 2008