Search Documents

By J. L. Jambor

Sulfide-rich tailings accumulated in a 4l-hectare impoundment at the Waite Amulet minesite near Noranda, Quebec, have undergone partial oxidation and destruction of the principal sulfides (pyrite and pyrrhotite) in the vadose zone. Mineralogical studies and whole-rock chemical analyses of 18 samples from 3 boreholes along a cross-section of the tailings pile indicate that the principal chemical manifestations of the alteration are a pronounced depletion in sulfide-sulfur, and an enrichment in total Fe as Fe203' Other elements such as Al, Mn, Mg, Ca, Na, and K in the solids show erratic or inconsistent variations, but a trend to Si enrichment in the oxidation zone is clear. The trend is interpreted to be a relative enrichment whereby the proportion of the stable silicate minerals has increased as a consequence of the consumption of pyrite and pyrrhotite in the oxide zone.

Jan 1, 1989

By Che Xin, Liu Tianlong, Bi Hongyun, Chen Lijia

"High-cycle fatigue experiments were conducted at 800°C in laboratory air for three ferrite stainless steels including 15CrNbTi, 15CrMoNbTi and 18CrNbTi, where the stress ratio of 0.l was adopted. The experimental results show that at 800°C, the fatigue limit of the 15CrMoNbTi steel is the highest, the fatigue limit of the 15CrNbTi steel is slightly lower than that of the 15CrMoNbTi steel, and the fatigue limit of the 18CrNbTi steel is the lowest. At the same maximum stress, the 15CrMoNbTi steel has longer fatigue lives than the 15CrNbTi steel in the low stress area, while the 18CrNbTi steel has the shortest fatigue life. In addition, the observations on the fracture surfaces of fatigue specimens reveal that the fatigue cracks initiate transgranularly at the free surface of the specimens and propagate in a transgranular mode.IntroductionIn modem automotive industry, the manufacturers have paid great efforts to clean exhaust gas and to improve fuel economy. It is thought an effective way to increase the temperature of combustion chamber in automotive engine. And thus, the manifold closed to the engine in automotive exhaust system can suffer high temperature up to approximately 1000°C. Because of their relatively low thermal expansion coefficient, high yield strength at elevated temperature and good fatigue resistance, ferrite stainless steels, especially added with alloying elements such as Mo, Nb and Ti, are increasingly used for automotive exhaust systems [1-3]. In fact, exhaust manifold operated under high frequency vibration and exposed to high temperature exhausting gas also requires good fatigue resistance at elevated temperature. Some studies on the high temperature fatigue characteristics of stainless steel have been documented. It has beeen found that the fatigue limit of four ferrite stainless steels including 409L, 436L, 429EM and 444 (18Cr- 2Mo) reduces significantly with increasing temperature [4, 5]. In the research concerning the effect of a-phase embrittlement on fatigue behavior in a high-chromium ferrite stainless steel, it is noted that the precipitation of brittle a-phase will reduce the crack initiation and growth resistances and result in a decrease in fatigue limit [6]. In this investigation, the high-cycle fatigue behavior of three ferrite stainless steels including 18CrNbTi, 15CrNbTi and 15CrMoNbTi at 800°C have been studied to address the mechanical aspect of high-cycle fatigue behavior for ferrite stainless steels and to provide the theoretical reference for the safe design of automotive exhaust system."

Jan 1, 2013

By C. Pichler, A. Ressler, D. Gregurek, A. Spanring

In order to improve the refractory lining life at one of the RHI key customer test procedures were developed within a two years collaboration project. In the first year of cooperation detailed refractory corrosion work in the rotary kiln with Ca-ferritic slag was performed. The main results of the second year of cooperation, reported in this article, involve a detailed testing work with nickel matte and pre-selected refractory brands which was performed in TBRC. A first part of this work was a complete chemical and mineralogical characterization as well as FactSage calculations carried out on provided matte samples. According to these results testing in the TBRC was realized at different process temperatures with several magnesia-chromite bricks. Based on the mineralogical investigation a high chemothermal load caused by sulfidic matte resulted in a deep reaching infiltration of the brick microstructure and partly corrosion of main brick components.

Jan 1, 2015

By J. E. Dutrizac

A mineralogical study of a weak acid leach residue from the Clarksville zinc plant of Savage Zinc Inc. was carried out. The study focused on Pb and Cd as these elements most significantly impact on the environmentally acceptable disposal of the residue. The residue consists of major amounts of bassanite, zinc ferrite and various Zn-Pb-Fe-Cd silicate species. Also present are lesser quantities of PbSO4, sphalerite, Fe2O3 quartz, Mn-Pb-Fe oxides, SrS04, (Pb,Sr)SO4 iron gel-silica gel, jarosite and Ti oxide. The principal Cd carriers are the zinc ferrite, which contains up to 9.00% Cd and likely accounts for -45% of the total Cd content of the residue, and the various silicate species which contain up to 6.97% Cd and account for about 45 % of the total Cd. The sphalerite is a minor Cd carrier containing an average of 0.35 % Cd and accounting for -5 % of the total Cd; the other carriers contribute only trace amounts to the total Cd content. The major Pb carriers are PbS04, Pb-bearing silicates and Mn-Pb-Fe oxides. Minor proportions of the total 1.09% Pb content of the residue are carried by SrS04 and (pb,Sr)S04' Trace Ph carriers include the iron gel-silica gel, Fe-Zn-AI oxide and bassanite. The residue after the toxicity characteristic leaching procedure (TCLP) is mineralogically very similar to the initial weak acid leach residue; the amounts of calcium sulphate are approximately the same in the two products. The principal Cd and Pb carriers are also the same as those noted in the initial residue, except that some dissolution and reprecipitation of Pb-Sr sulphate takes place. That the residue fails the TCLP test is likely a consequence of the superficial dissolution of Pb and Cd from species such as PbS04 or Zn-Pb-Fe-Cd silicate.

Jan 1, 1995

By Richard Hollis

The Mount Isa copper smelter was expanded in 1998 to a capacity of over 250000 t/y anode copper. This tonnage will be produced from a single stream consisting of an Isasmelt smelting furnace, and four Peirce-Smith converters - one of which was installed as part of the expansion project. During the course of the expansion project Mount Isa Mines Limited (MIM) signed an agreement with WMC Fertilizers Ltd (WMCF) to supply sulphur containing smelter gases over the fence to a new sulphuric acid plant to be built by WMCF. This will result in a further increase in copper production by reducing the time when smelting is curtailed by Air Quality Control restrictions. As well as the need to modify the primary gas system to connect to the acid plant, the hoods and crossover ducts and their support structures on the original three converters required replacement, and secondary ventilation was also needed to improve converter aisle hygiene. Each of these areas was addressed by the project. Preliminary ideas for carrying out the modifications were found to have a serious impact on converter aisle operations, and would have led to a production loss of over 50000 tonnes of copper. Following benchmarking in other copper smelters, a suitable construction plan was developed and carried out to minimise this loss. This paper describes the methodology and construction plan adopted.

Jan 1, 1999

By P. K. N. Raghavan

This paper identifies potential technologies for Carbon dioxide abatement from the mining and metal industry with special reference to the Aluminium industry. Mine reclamation could contribute to this effort to successfully reach the greenhouse gas (GHG) emissions reduction commitments for a nation. An overview of GHG production by the mining and metal industry together with a review of principles used to set the context in which specific options for GHG reduction are described. Options for GHG reduction in the mining and metal industry include reforestation, Addition of soil amendments or neutralizing agents, CO2 capture and storage, initiatives towards energy reduction, waste heat recovery and alternative energy use. An analysis and quantification of the potential GHG reduction of potential carbon sinks and sequestration options for the mining and metal industry are provided. Cost estimates for different options are provided. The paper also identifies sources that could fund research regarding GHG reduction options. The paper concludes with recommendations.

Jan 1, 2011

By Kimio Itagaki, Makoto Ohtsuka, Kouki Chiba, Minoru Matsumoto

"The properties of Ni-Mn-Ga films such as chemical composition, crystal structure, microstructure and transformation temperature were investigated with respect to sputtering conditions in the present study. The Ni-Mn-Ga films were deposited on a polyvinyl alcohol substrate with a radio-frequency magnetron sputtering apparatus using the NisoMn2sGa2s and Nis2Mn:«1Ga24 targets. After separating from the substrates, the films were annealed at the temperature between 873 and 1273 K for 3.6 ks. The chemical composition of the films depended on the radiofrequency generating power, however, there was no dependence on the heat treatment temperature. Each deposited film had a columnar grain structure. After heat treatment, the width of columnar grains widened and then became indistinct with increasing heat treatment temperature. The Heusler type cubic crystal structure of the fi4n with heat treatment at 1073 K changed to the tetragonal one through the martensitic structural transformation during cooling. The martensitic structural transformation temperature increased with increasing nickel content of films, while the Curie temperature decreased. The film obtained at 200 W using the Nis2Mn24Ga24 target after heat treatment at 1073 K showed one-way shape memory effect through the reverse martensitic structural transformation during heating.IntroductionThe ternary intermetallic compound NiiMnGa has a Heusler-type crystal structure and is an intelligent material, which has a shape memory effect and a ferromagnetic property. The martensitic structural transformation occurs within the ferromagnetic temperature region. The cubic crystal structure of L21 at high temperature changes to a tetragonal one through the martehsitic structural transformation during cooling. The films of this compound can be applied for an actuator of micro-machines."

Jan 1, 2000

By Christine Wenzl, Andreas Filzwieser, Stefan Konetschnik

"The METTOP-BRX-Technology is a novel manifold electrolyte inlet, which allows improved productivity and production in new and existing tankhouses by achieving higher current efficiency and cathode quality, as well as using current densities higher than 400 A/m2. Two installation examples are shown: Montanwerke Brixlegg AG, Brixlegg, Austria (upgrade of existing tankhouse) and Xiangguang Copper, Yanggu, China (new tank house). Montanwerke Brixlegg AG has been using the METTOP-BRX-Technology since 2005, and converted half of the whole tankhouse to METTOP-BRX in 2011 in order to use a current density of more than 400 A/m2. Xiangguang Copper started up their second tankhouse in May 2011. This tankhouse was constructed in the same way as the existing tankhouse, but was designed for 292,000 t/a cathode copper (existing tankhouse: 200,000 t/a) by using the METTOP-BRX-Technology. This production increase is a consequence of a much higher current density, namely 410 A/m2, compared to 280 A/m2 in the old tankhouse.IntroductionCopper electrorefining has been practised for more than hundred years, the last big change being the implementation of stainless steel cathodes in the 1980s [1], In 2005, the METTOP-BRXTechnology was first introduced. This technology was developed jointly by METTOP and Montanwerke Brixlegg, Austria, and allows improvements in productivity and production in new and existing tankhouses in an economic way. The METTOP-BRX-Technology is a novel manifold inlet that allows improved tankhouse productivity by increasing current density and/or current efficiency while maintaining or improving cathode quality [2]."

Jan 1, 2012

By Wade L. Karlsen

"Revision surgery to replace joints in the human body requires materials that are strong, long-lasting, and biocompatible. Metallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an on-going effort to economically improve their performance. Alloying with inert nitrogen can enhance the mechanical properties of the alloy, enhance its corrosion resistance, and elevate the temperature at which the metallic implants can be thermally treated, without increasing the threat to the human body. The current work has produced a high-nitrogen Co-Cr-Mo alloy through HIP consolidation of metal powders that have undergone nitriding in a mechanically fluidized bed. The already fine microstructure of the powders combined with the increased nitrogen content resulted in significant property gains in the consolidated materials.IntroductionMetallic implants made of cobalt-chromium-molybdenum alloys are already popular because of their proven corrosion and wear resistance properties, but there is an ongoing effort to improve their performance. Research on a Stellite 21 cobalt-chromiummolybdenum alloy has shown that nitrogen alloying can be desirable from several standpoints [l]. Firstly, it has indicated that nitrogen can enhance the mechanical properties of the alloy, which could allow more demanding implant designs. The same work also demonstrated that nitrogen can elevate the temperature at which the metallic implants can be thermally treated, which is desirable in situations in which surface textures are to be sintered to the implant to enhance its fixation properties. Finally, that research work discovered that, not only does nitrogen not harm the corrosion resistance of the cobalt-chromium-molybdenum alloys, but it may in fact enhance it. Combining this with the fact that small amounts of nitrogen are not considered a threat to the human body, makes nitrogen alloying an attractive alternative for enhancing the properties of Co-Cr-Mo."

Jan 1, 2000

By Yuanbo Zhang, Yongbin Yang, Guanghui Li, Zhengwei Yu, Yufeng Guo, Tao Jiang, Xiaohui Fan, Youming Hu

"Composite agglomeration process (CAP), as an innovative method for preparing blast furnace burden, was developed and has been put into operation in China. CAP is different from traditional agglomeration processes of iron-bearing materials involving sintering and pelletizing. Compared to the traditional agglomeration processes, CAP is characterized by several strengths such as permission of diverse iron-bearing materials in production, obvious improvement of permeability in the feed bed, decreasing the fuel consumption and remarkably increasing the productivity of sintering machine. Furthermore, the use of the composite agglomerates prepared with CAP is capable of obviating the negative effects caused by the differences in quality of sinter and pellets on the operation of blast furnaces. This paper mainly presents an overview of the principle and applications of CAP.Development Background and Principle of CAPhe traditional agglomeration processes including sintering and pelletizing have been the two predominant methods for preparing ironmaking burden from iron-bearing materials. Sintering is a way for agglomeration by heating the coarser fine ores (general granularity 0~10mm). The mechanical strength of irregular porous sinter is obtained by the solidification of molten phase at high temperature process. It has been shown that the production of high basicity sinter (R=1.8~2.2) is characterized by low energy consumption and high efficiency compared to low basicity sintering. Meantime, the finished high basicity sinter is characterized by good mechanical strength and metallurgical performance. Pelletizing is another way for agglomeration by firing wet green pellets, which are balled from the fine grained iron ores or concentrates. Based on the differences of chemical compositions, the finished pellets can be divided into acidic oxidized pellets, fluxed pellets, magnesium-bearing pellets, and so on. The acidic oxidized pellets are the dominant products of modern pelletizing."

Jan 1, 2012

By Caisa Samuelsson, Taishi Matsushita, Hannes Holmgren, Sina Mostaghel

"Rönnskär Smelter of Boliden Mineral AB, Sweden, is a large end-processor of secondary raw materials and waste, including electronic scrap. Electronic scrap may introduce various impurities to the smelter's flow-sheet, among which alumina is a common and significant one. This article summarizes the results of an ongoing research at Luleä University of Technology, Sweden, to study the influences of alumina on different properties of slag from the zinc fuming process at Rönnskär smelter. A combination of different experimental techniques and thermodynamic calculations have been used to investigate properties such as density, surface tension, effective thermal diffusivity, viscosity, and melting/leaching behaviors. Results show that the addition of alumina to this slag increases the degree of polymerization of the melt, and physical properties vary correspondingly. Mineralogy of the semi-rapidly solidified samples is also changed due to alumina addition. A correlation between mineralogy and leaching behavior can be observed.IntroductionBoliden's Rönnskär Smelter is a base- and precious-metals producer located in north of Sweden. Its main products are copper, zinc clinker, lead, gold, and silver. Sulphuric acid, liquid sulphuric dioxide and iron sand (granulated slag) are some of its main by-products. In order to optimize the overall outcome of the process, different refining units are integrated in the smelter's flow-sheet (Figure 1). Copper concentrates and fluxing materials (mainly silica sand) are charged to the process. The produced matte is sent to the converter and the generated slag is charged to the fuming furnace, where it is treated by reducing gases to produce zinc clinker. The converter's slag is charged to the electric furnace, while the fumed slag is tapped into the settling furnace for further cleaning, where matte, slag and speiss (residual metals) are separated. The matte from the settling furnace is also sent to the converters; its speiss is sold to external customers; and its slag is water granulated and sold as construction material, which is known as iron sand."

Jan 1, 2012

By U. Lauwers

The influence of different waste materials in sinter blends on the quality and mineralogical composition of a sinter is described. As a result of partial preservation of the original textures of waste materials in the final product the degree of assimilation of the original material in the sinter product can be ascertained. Recycling of waste materials such as dolo char , arc-furnace slag, scrap fmes, mill scale and BOF-mud via the sintering process a saving on costs of raw materials such as flux and fuels, and a reduction on pollution can be achieved. A comparison of a typical sinter with a sinter produced through the utilization of waste materials showed a distinct correlation between certain types of waste material and some metallurgical properties. Dolochar in a sinter blend acts as part of the fuel and flux that are normally added to a sinter mix. Generally dolochar improves the quality of the sinter and decreases the consumption of coke. Other waste materials adversely influence the quality of the sinter. The glass and calcium ferrite content of a sinter when dolochar is used in the blend is similar to that of a sinter produced with only coke as a fuel in the sinter mix. The glass content is lower and the calcium ferrite content is higher, in a sinter produced from dolo char in the blend compared to a sinter produced with additions of other waste materials. Changes in the mineralogical composition are related directly to the metallurgical properties of the sinter product.

Jan 1, 1991

By Shun Myung Shin, Kang Jeong, Kyoungkeun Yoo, Jin Koo, Dong Hyo Yang, Soo Sohn

"The optimum discharging condition to dismantle the batteries without explosion was investigated to recycle the lithium primary batteries, which could be exploded by heating too much or crushing. The 3 waste lithium primary battery cells were discharged with 500 cm3 of 0.5 kmol·m-3 sulfuric acid. Fe concentration and pH increased rapidly after 3 days at 35? and after 1 day at 50?. Chromium concentration increased by 4 days at 35? and 2 day at 50?and then decreased, and nickel concentration was very low. Because Li concentration increased gradually, Li became dissolved after the dissolution of cover material. When the discharged batteries were shredded, the batteries discharged at 50°C were not exploded and those discharged during 3 days at 35°C were exploded. This result shows that the waste batteries could be stabilized within 1 day at 50°C and 4 days at 35°C. Introduction Lithium has some advantages for battery e.g. it is the lightest metals and also has the highest electrochemical potential at 3.04V[1]. For over thirty years lithium primary batteries became famous for their performance in various applications such as IT, medical, and military[2,3]. They gained a reputation for their long shelf life, constant voltage, wide operating temperature range, and low self-discharge characteristics[3-5]. World primary lithium battery market was expected to grow from $820.6 million in 2003 to $1,1355.3 million in 2010 (http://www.frost.com, Frost & Sullivan)[2-4]. The lithium primary batteries have very various sizes and components. Lithium batteries are made with lithium metal as anode active material and non-aqueous solvent as electrolyte. As cathode active material, various kinds of materials were used such as manganese dioxide (nominal voltage, 3.5V), thionyl chloride (3.6V), and carbon monofluoride (3.0V). In Korea, 50 % of the spent lithium primary batteries must be recycled because spent lithium primary batteries have been listed in EPR (Extended Producer Responsibility) of the enforcement degree of the act on the promotion of saving and recycling of resources. However, the batteries have been landfilled since there is no economic method to recycle the batteries in Korea[2,3]. When the batteries were heated too much, charged, pierced, over discharged, or short-circuited, the batteries explode because lithium reacts violently with water or air and because contents such as lithium, electrolyte, and sulfur become flammable by high temperature[4]. Therefore, it is so difficult to recycle safely the spent lithium primary batteries."

Jan 1, 2008

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By Milton Blander

A review of concepts and theories for predicting thermodynamic solution properties of multi- component high temperature liquid solutions is reviewed. During the last 50 years the ability to predict :such properties for molten salts, silicates and metals based on the generally known properties of the lower order (often binary) systems has been developed and shown to provide predictions which are quite useful in science and technology. There are many gaps in our understanding of these high temperature solutions, especially for metals, and considerably more work is needed.

Jan 1, 1996

By Kumar Ganesan

Elevated mercury levels are expected in aged gold mine tailings due to residual mercury from the amalgamation process, The fate of mercury in tailings is not well understood, Its potential health risk depends mainly on the degree to which mercury is mobile in soil. Mercury is re-moved from soil by evaporation, plant uptake, microbial activities, leaching, and other physico-chemical processes. In this research the amount of mercury lost by evaporation was evaluated. Several aged gold mine tailings in Montana were sampled for total mercury and its flux into the atmosphere. Mercury levels in tailings were higher than the general background levels in most sites. The mercury levels in some cases were as high as 10,000 ug/g. The field measurements using flux chambers indicated a wide range of mercury flux from aged gold mine tailings. The mercury flux ranged from 0-11,000 ng/m2/hr. The mercury loss by evaporation helps rid the soil of mercury but the mercury vapor then will participate in the atmospheric mercury cycle, The low solubility of elemental mercury in water helps to minimize mercury leaching from tailings, however, conversion of elemental mercury to more soluble forms by bio-geo-chemical processes can enhance its mobility posing increased health risk.

Jan 1, 2003

By T. T. Chen

Gold in the Twin Creeks ore is primarily associated with arsenian pyrite. During pressure oxidation, the sulphides are solubilized, but part of the dissolved iron reprecipitates as jarosite and as an iron sulphate-arsenate-phosphate phase. The pressure oxidation products are subjected to cyanide leaching. The cyanide leach residues consist of quartz, gypsum, bassanite, anhydrite, small amounts of jarosite, an iron-sulphate-arsenate-phosphate phase, as well as trace amounts of orthoclase, rutile, pyrite, hematite and monazite; all these particles are dispersed in a fine grained matrix of illite-muscovite. The autoclave leach residues contain a small amount of carbonaceous matter. Many gold grains are detected on the surfaces of the carbon particles, and these gold particles are not leached during cyanidation. The gold particles are typically 0.1-0.2/Lm in size and commonly are embedded in the carbon surface or are coated with a K-AI-Si-S-O phase on the surface of the carbon. The gold grains are consistently associated with elevated CI contents (50-300 ppm Cl). The poor gold cyanide leach recoveries, which initially occurred in the Twin Creek developmental circuit under certain operating conditions, are attributed to the presence of chloride in the feed. This results in the formation of soluble gold chlorocomplexes in the autolcave and the subsequent sequestering of the gold on the surfaces of the carbon particles.

Jan 1, 2000

By S. S. Ryu, J. C. Kim, H. Lee, Y. D. Kim, I. H. Moon

"Recently, W-Cu alloy becomes one of the very important candidate materials for heat sink and packaging in the field of microelectronics due to its good thermal properties. The metal injection molding of W-Cu powder can satisfy the requirement for mass production of complex shaped parts in microelectronic devices. In the present study, the application of MIM process to the nanostructured W-Cu powder prepared by mechanical alloying was investigated. The multi-component binder system of 45PW+ l 5BW+ 30PE+ I OSA was proven to be suitable one for the MIM of the W-Cu composite powders by adopting the debinding cycles of multi-stage in N2 and H2 atmospheres. Other process conditions for the MIM of the nanostructured W-Cu composite powder were also studied. The MIM debinding part of W-30wt.%Cu was sintered to the relative density of more than 96% by sintering at 1200 °C for !hour in H2 atmosphere. Such an improvement of sinterability was attributed to the intrinsic homogenous and fine mixing state of W-Cu phases in nanostructured W-Cu composite powders, and also partly to the effect of the activated sintering by the presence of impurity introduced during the extensive milling.IntroductionW-Cu alloys have been widely used for heavy duty electrical contacts and arcing resistance electrode(1-2). Recently there has been a growing interest in this W-Cu alloy because of its superior thermal managing properties and its high micro wave absorption capacity(3). Such W-Cu alloy parts are conventionally fabricated either by the Cu infiltration sintering technique or by hot pressing of W-Cu powder mixtures. However, these conventional PM techniques are hardly applicable for mass production of small size parts with a complicated shape such as the parts required for microelectronic devices. The metal injection molding(MIM) technique is potentially applicable for the mass production of small and complicatedly shaped parts compared with other PIM forming techniques."

Jan 1, 1998

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013