Search Documents

By Rudolph P. Frizzi

Structures supported on ACIP and DD piles perform successfully when quality control is maintained from the initial site subsurface investigation through pile design, bidding, and construction. The four stages of ACIP / DD pile construction are: preparation, augering the pile, grout / concrete placement, and reinforcement installation. During all four stages, careful observations and communication between the contractor and the owner's engineering inspection personnel are vital to successful pile completion. Automated monitoring equipment (AME) exists to supplement, but not replace, the field personnel's observations during the pile augering and grouting operations. Full-scale field load testing is done to verify the pile's geotechnical and structural design, and the contractor's pile installation means and methods, using several procedures including: conventional top loading, high-strain dynamic, rapid axial compression (i.e. Fundex PLT and Statnamic), and Osterberg Cell. Non-destructive sonic testing is performed to investigate the below-grade sectional properties of the completed pile; such methods include: low-strain impulse testing, and single-hole and cross-hole sonic logging. Post-construction observations are necessary to verify pile location and top properties prior to overlying cap construction.

Jan 1, 2005

By J. G. La Fonta

The rapid development of real-time monitoring technology for the construction of large underground structures in urban areas can be attributed to: the zero-risk objective, the need for transparency between all parties involved and the control of real cost within the budget. Real-time monitoring can be an integral part of the construction contract (for example when compensation grouting is required) or independent, in particular when measurements of existing structures and buildings bordering the project are to be taken before construction starts. Three examples of extensive field instrumentation schemes are described: a large road tunnel in the Moscow suburbs, a new metro line in Amsterdam and major redevelopment works at a busy Central London rail interchange.

Jan 1, 2006

By Manuel M. Reyes, Thuraisamy Thavaraj, Alex Sy

"The new east span of the San Francisco-Oakland Bridge features a single tower self-anchored suspension (SAS) bridge. During construction of the SAS bridge, a temporary bridge was used to support the box girders until erection of suspension cables was completed. The transfer of deck load from the temporary bridge to the suspension cables was achieved in November 2012 and the SAS bridge has become the largest of its kind in the world. The new bridge will be in service in Fall 2013.Large diameter driven steel pipe piles were used for the temporary bridge foundations at Towers D, F and G located in San Francisco Bay. At Tower D, the large diameter steel pipe piles were driven through thin overburden into bedrock using a large Menck MHU500T hammer with a rated energy of 550 kJ. As there was no precedence in driving open-ended pipe piles into the Franciscan Formation bedrock, challenges were faced with uncertainties in drivability, driving stresses, pile embedment in bedrock and pile capacity. These uncertainties were addressed by incorporating additional measures into the pile design, and by the use of dynamic pile monitoring during initial driving and re-strike. Pile relaxation was observed during pile installation.At Towers F and G, setup effect was a key issue for the piles driven into the deep soft marine sediments. Drivability analyses were conducted to predict pile run, driving stresses, selection of hammer and refusal criteria. The piles were dynamically monitored during driving to estimate pile capacities. Due to the set-up effect in the Bay Mud, the piles gained up to 3.3 times the initial capacity during the re-strike and were in excess of the design capacity.This paper presents details of the design, construction, testing and performance of the driven pipe piles at temporary Towers D, F and G. Settlement data of the temporary tower foundations while in service confirmed the satisfactory performance of the pile foundations.INTRODUCTIONThe new east span of the San Francisco-Oakland Bay Bridge features a single tower self-anchored suspension (SAS) bridge, the largest of its kind in the world. The new east span replaces the existing double-deck steel bridge built in the mid-thirties. A span of the existing bridge had collapsed during the 1989 Loma Prieta earthquake but was repaired. Construction of the new east span commenced in 2008 and is expected to be completed for the Labour Day opening in 2013. Figure 1 shows a schematic (looking north) of the new bridge with its 160 m high main tower T1 in the middle, and Piers W2 and E2 at the west and east ends, respectively. The west and east spans of the SAS bridge are 180 m and 385 m, respectively.During construction of the SAS bridge, a temporary bridge, complete with towers and trusses, was used to support the box girders of the new permanent bridge until the loads from the box girders were transferred through suspension cables to the permanent bridge. The transfer of deck load from the temporary bridge to the main cable was completed in November 2012."

Jan 1, 2015

By Walid El Kamash, Sadik Oztoprak

"Soft soil presents a challenge against multistory buildings in some cities of Egypt such as Port Said due to the consolidation settlement. Deep mixed (DM) columns are used to improve the soft foundation soil in order to reduce the total and differential settlements. Latest research revealed that this improvement technique also increases the rate of mechanical consolidation due to column yielding caused by stress concentration from the soft soil. In this study, extended poly-styrene (EPS) Geofoam is used to replace the soft soil over DM columns in order to control the stress concentration and settlement. To understand the effect of EPS geofoam on the degree of consolidation, stress concentration and settlement, a parametric study was carried out through a mechanically and hydraulically-coupled numerical method. A unit cell model is used, in which the soil was considered linear elastic; DM column and EPS Geofoam are elasticplastic materials. Results reveal that EPS geofoam is helpful for reducing the settlements and accelerating the consolidation. Increasing the length of the column of the deep mixed foundation with EPS geofoam has a significant effect on accelerating the consolidation.INTRODUCTIONExpanded polystyrene (EPS) geofoam is a lightweight polymeric material which is made by expansion of raw plastic beads. The expansion of the EPS beads are spherical-shaped particles containing closed hollow cells. EPS which plays an important role as an innovative lightweight construction material is now well recognized due to its low density in addition to high compressive and rupture strength. Inglis (1996) reported the first use of EPS geofoam as a seismic buffer to reduce potential seismic loads against a nonyielding basement wall. Gaskin (2000) and Bathurst et al. (2007) carried out reduced-scale shaking table test on a rigid retaining wall protected by EPS geofoam. The test data showed that the peak lateral loads acting on compressible model walls were reduced below values measured for nominally identical structure but with no compressible inclusion. Abdelrahman and El Kamash (2014) investigated the behavior of EPS Geofoam beneath raft foundation on soft soil of Port Said. They showed the ability of EPS to control vertical displacements. The investigation of the behavior of EPS geofoam with DM column has not attracted more attention of previous researchers. In this paper, the behavior of replacing the soft soil by EPS geofoam was examined in the presence of DM column."

Jan 1, 2015

By Abhijit Saha

"The stone columns improve the performance of foundations on soft and loose soil due to the ability of composite ground to sustain increased structural loads under reduced settlements. The interaction between the two basic elements: the ambient subsoil and installed column, present a complexity of behaviour, both in terms of applied stresses and resulting strains. Moreover, as the same is provided in-group in a regular array beneath foundations, the performance of an individual column is likely to be influenced by the presence of neighbouring columns. The present paper addresses this very issue. Analysis of reported field hydro-test data of large diameter oil storage tanks in soft ground in reference to some existing theories led to the development of the stone-column ‘group efficiency factor’. In order that such factor is of general use, it was felt necessary to examine the applicability of the factor to different sizes of groups under varied subsoil conditions. With this in view, some model test results reported in literature of single and group of columns have been analysed and in the process an explicit relationship regarding the stone-column ‘groupeffect’ could be established.INTRODUCTIONThe field application of the stone column technology has gained momentum than the intricate design methodology due to its simplicity in installation and intuitive performance. The ground improvement is due to the complex interaction within the ‘unit-cell’ comprised of the installed column in ambient ground under sustained vertical stress; in association with the interdependence of problem geometry and material properties of the two different soils-one 'native' and the other 'back-filled'. The beneficial effects are increased load capacity, reduction in total and differential settlements, minimization of post construction settlements effected by accelerating consolidation, reduced risk of soil liquefaction, aiding in improvement of slope stability of embankments and natural slopes and effecting changes in the dynamic response. The ‘unit-cell’ concept of a tributary soil cylinder encapsulating an installed column with some reasonable assumptions and boundary conditions (Aboshi et al, 1979; Balaam & Booker, 1981; Van Impe & De Beer, 1983; Priebe, 1976; Saha & De, 1994; Saha; 2005, 2006, 2007, 2011, Saha & Das; 2007) deals with the load-settlement behaviour of the composite system. The present investigation is based on published field data from literature & validated with experimental study reported in literature. The study addresses the effect of group interaction of stone columns beneath a large area loading on ground settlement. The hydrotest load-settlement data of 12 large diameter oil storage tanks founded on stone column reinforced soil at Haldia1 and Kandla2 refinery sites in India; reported by Som (1997), has been analysed to quantify the group efficiency. The results as obtained are compared with experimental study on 2, 3 and 4 stone column groups at different spacing-diameter ratios in soft clay3 reported by Rao et al (1997) to validate the above analysis. A unique relationship between the column spacing and group efficiency has been obtained."

Jan 1, 2015

By Ben M. Lewis, Yogesh Prashar

"The East Bay Municipal Utility District (EBMUD) is a major water utility service providing water to over 1.3 million people in the eastern San Francisco Bay Area. EBMUD manages 28 dams at 5 terminal and 23 open-cut reservoirs within a 331-square-mile customer service area. As part of a 2012 update on EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, EBMUD has decided to replace Central Reservoir, a 152.8 milliongallon open cut reservoir, with optimally sized tanks. This paper presents the results of an analytical comparison of various foundation reinforcement solutions for the proposed tanks including: Cement Deep Soil Mixed (CDSM) columns, vibro stone columns, rammed aggregate piers, and lightweight cellular concrete fill. The computational program GeoMat (www.ensoftinc.com) was used to perform simplified soil structure interaction analyses. Settlement estimates were developed for each alternative with the proposed loading and compared to an allowable differential settlement criterion established at 0.3-inches over a 50 foot length. The authors wish to present the importance of considering mat and soil interaction along with various settlement mitigation methods considered for this challenging project.INTRODUCTIONProject BackgroundCentral Reservoir is an operational open-cut reservoir located north of the intersection of 25th Avenue and East 29th Street in Oakland, California. The reservoir is bound by 23rd Avenue to the west, Sheffield Avenue to the east and Interstate Highway 580 to the north. Originally, the Central Reservoir site was a drainage swale incising into weathered bedrock formed from Pleistocene alluvial deposits. The reservoir was first constructed in 1910 by excavating a basin below grade and constructing an embankment dam on the south and cutting/filling the bedrock and alluvial deposits from the drainage swale. The main dam at the Central Reservoir site is also a DSOD (Department of Safety of Dams) jurisdictional dam and as such is regularly monitored by the EBMUD Materials Engineering Section and the California DSOD.In a 2012 update to EBMUD’s Infrastructure Rehabilitation Plan for Distribution Reservoirs, Central Reservoir was identified as a critical facility that has reached the end of its useful life and must be replaced due to: a failing panel craft lining which contains polychlorinated biphenyls in the interior coating, a roof that does not meet the current seismic code, and reduced operating levels due to potential leakage in the upper portions of the panel craft lining. Furthermore, Central Reservoir is about three times larger than required and is located at a lower elevation than other regional reservoirs in the pressure zone resulting in increased labor-intensive operational challenges and water quality operations.This project presents some challenging geotechnical demands – the site is founded on weakly consolidated Holocene Alluvium overlying weathered bedrock, the proposed structural loads are large, and the new Central Reservoir is to be placed on a pad at an elevation of 182 feet, required placement of up to 30 feet of fill over the current basin. Additionally, the project aims for a long-term foundation solution that will outlive the new replacement tanks and accommodate future site upgrades. In order to meet this goal, the differential settlement criterion for the tanks was ¼ inch over 50 feet length. Lastly, the project also aims to address EBMUD’s increasing trench spoil stockpiles by recycling discarded trench spoils as fill for the proposed tank pad."

Jan 1, 2016

By Steven R. Ahlfield, Ali Ghandeharioon

A wastewater treatment plant commissioned in 1978 is undergoing a major expansion. Planning various phases of the 8-hectare expansion at this site requires an understanding of the site response during and after construction, and the potential impact on adjacent properties and infrastructure. The expansion project requires nominally 5 m of site grading fill for flood protection. The site is underlain by loose to compact fine sand over firm to very stiff clay stratum that extends to great depths. Ground improvement is required to mitigate the liquefaction hazard in the fine sand stratum, and preloading is proposed to reduce post- construction settlements in the deep clay. Site development and foundation systems for the plant expansion project were evaluated by conducting settlement analyses which accounted for the historic and future site loading and 3-D modeling of soil layers with interpolation between borehole and cone penetration test (CPT) locations. The numerical model was calibrated to match short-term and long-term settlements measured at the plant site. The analyses were carried out to assess the effects of past loading, proposed preload and surcharge heights, lateral extents and durations as well as vibro-replacement ground improvement on post-construction settlements. Two design options were considered for the preload footprint across the site and foundation system for proposed facilities. It is shown that limiting the preload extent and founding some of the proposed structures on deep friction piles reduce the predicted settlements of adjacent infrastructure and result in reasonable performance for the proposed facilities. INTRODUCTION A wastewater treatment plant commissioned in 1978 will be replaced with a new plant on an undeveloped portion of the site to provide wastewater treatment for an expanded service area. The existing facilities must remain in operation until completion of the new plant. The site grade will be raised nominally 5 m for flood protection. The large areal extent of the site grading fill and plant structures will cause stress changes extending to great depths in the underlying soils and result in settlement of the existing and new structures. Historic settlement of the existing facilities has been tolerable for plant operations, but no settlement performance data was recorded during site development and post-construction from 1978 to 2007. Development of the 8-hectare expansion at this site is planned in three phases to reduce the overall construction schedule. Planning for each phase requires evaluating the effects of various site development activities from start to completion of expansion and during the design life (i.e. post-construction period), and the potential impact on existing wastewater treatment facilities and adjacent properties and infrastructure including an adjacent viaduct structure. Figure 1 presents the site plan and three distinct site development phases considered for the plant expansion.

Jan 1, 2019

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By Vijaya Bhushan Rao, Jason Redgers

A mixed-use development comprising of multistoried residential towers, retail and associated infrastructure covering an area of 500,000 m2 is under construction in Dubai. The subsoil conditions consist of calcareous sands with high carbonate and shell content with hard and competent strata encountered at varying depths. To achieve the design requirements of soil stiffness, friction angle, limit differential and total settlements and mitigate the liquefaction due to a seismic event then ground improvement were deemed necessary. In order to provide the most time and cost efficient solution numerous techniques were applied to meet the requirements for all depths such as Vibrocompaction, VC (depth >8m), Dynamic Compaction, DC (depth < 8m)] and Rapid Impact Compaction, RIC (depth <4m). The specified ground improvement requirements were translated into a target Cone Penetration Test, CPT line that served as the defacto performance requirements for the project. Suitable correction factors were applied to the CPT results to account for the high carbonate content following the works of Al-Homoud and Wehr 2006, Belotti and Jamiolkowski , 1991 and Vesic, 1965. Furthermore, the alpha factor, α, used to obtain stiffness from CPT results was applied following A.C. Meigh 1987 and Massarsch & Fellenius, 2005 where high over consolidation ratios (OCR) could be demonstrated.

Sep 8, 2021

By John L. Walkinshaw

It is obviously not possible in the time given me today to review in great detail all the research of the past 20 years that the (FHWA) has sponsored or participated in. In this presentation I will highlight some of the principal programs that I am familiar with. This handout lists practically all the reports prepared for the FHWA involving deep foundations and some related work involving the same structural elements (piles, shafts, ground anchors).

Jan 1, 1993

By Matthew Janes

The RC Harris Filtration Plant, which treats the majority of the fresh water for over 2.5 million Torontonians, is a Canadian Architectural Heritage site demonstrating a classic example of Art Deco Architecture. The facility is undergoing an expansion to install an underground sludge treatment capability. Perched atop a bluff on the North shore of Lake Ontario the structure enjoys a commanding presence on the Lake Ontario shoreline. A series of underground tanks were proposed for the hillside below the structure, which when covered would preserve the building?s architectural presence. However, the plan required two, stepped excavations 12 m and 10m deep into compact, wet sands over stiff clays and clayey silts. Concerns regarding the original structure influenced designers to set the lateral deflection limit for the front footing of the existing structure at 4 mm, (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Analysis indicated installation effects and overall elastic movement of the soil mass beneath the building would result in movements of 7 to 9 mm at the structure. Through extensive FLAC analysis and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept. Based upon the analysis the design-build team negotiated a new deflection criteria dictating a maximum of 2.0 mm of movement across the critical expansion joint between the Filter Building front footing and the tank slab beyond. The contractor invested in additional pre tender soils investigation to support the refined design process. The FLAC analyses indicated the Filter Building movements would be elastic and distributed up to 50 m back beneath the front footing of the structure. An extensive precision monitoring program proved construction related movements of 6 to 10 mm horizontal at the front footing. Extensometers placed at two locations over the critical interior tank expansion joint showed no measurable movements. The overall monitoring program, including inclinometers, tilt meters, tie back extensometers (smart cables) and tie back load cells indicated a good match between recorded movements and loads and those predicted by FLAC Analysis.

Jan 1, 2006

By Andrew Middleton, Mick Stadter, Chris Crowe, David Chong

"The Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line in the south east suburbs of Melbourne. The works involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil was removed. The project has presented significant geotechnical challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. These challenges included temporary and permanent wall stability, foundations, earthworks and dewatering. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community and meet the project timeline.INTRODUCTIONThe Level Crossing Removal Project – Package 1 is part of the Victorian Governments commitment to remove 50 of the most dangerous and congested level crossings across Melbourne. This involved removing three crossings on the Frankston Line where it crosses North Road in Ormond, McKinnon Road in McKinnon and Centre Road in Bentleigh.The project involved replacing approximately 2.5km of at grade track with three rail cuttings up to 8 m deep at each of the bridges that replace the level crossings. The cuttings will accommodate three lines of rail tracks with the cuttings up to 25 m wide. The cuttings are retained by piled retaining walls and during the main construction occupation approximately 250,000 cubic metres of soil has been removed.The project presented significant challenges due to the location in residential suburbs and tight rail corridor and rail occupation timeframe. As a result, careful design and innovative construction techniques have been necessary to limit impacts on the community. The geotechnical challenges generally fell into one of three areas, earthworks, structures and groundwater. The primary earthworks challenge for the project was moving the 250,000 cubic metres of soil in a 10 day window, however, from a geotechnical viewpoint, obtaining a stable subgrade on which to operate the necessary construction plant in a short time frame with constrained site access and time to import materials was the key. Whilst closely watching the performance of the dewatering system, a range of contingency plans were developed to cope with any difficulties."

Jan 1, 1900

By Wojciech Szczepiński, Dominik Gächter

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Oct 1, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Chu E. Ho, Paul Napoli

A new waterfront park was developed on Long Island in close proximity to the East River and Newtown Creek. The existing ground consisted of fill over soft organic clay, medium dense silty sand, glacial till and schist bedrock. The ground was initially raised to preload the underlying soft soils to stabilize the ground in preparation for site development. The ground was subsequently cut down to temporary grades for installation of foundation piles for the overlook structures and construction of reinforced concrete cantilever retaining walls forming pathways located adjacent to the water bodies. The retaining walls were located in two rows at different elevations along the sides of a steep embankment. Where the pathways converge, some of the walls were too close to each other, and were redesigned as a combined U-wall with a common base slab. The individual retaining walls were designed for adequate bearing, sliding and overturning resistance. Ground anchors were installed to enhance global stability of the retaining walls. This paper presents the design considerations for the retaining walls for various loading conditions, and evaluation of the trial and proof tests for the anchors. INTRODUCTION The New York City Master Plan included the transformation of an approximately 30-acre parcel of land in Long Island City, Queens, New York from a former manufacturing zone into a residential, commercial and recreational zone for middle-income community. The site was located at Hunters Point South along the eastern shoreline of the East River and Newtown Creek (Figure 1). The development included low to high- rise residential buildings, a public school, and retail structures. Open spaces were provided along the East River and Newtown Creek waterfronts in the form of a continuous park providing for recreational and community-related activities. Waterfront structures included small park buildings, walkways and viewing platforms. The shoreline was surrounded by revetments as part of the flood mitigation strategy. The project involved extensive site re-grading and several retaining walls were constructed. The earthwork volume amounted to approximately 47,000 cubic yard of imported fill and 93,000 cubic yard of cut. The exposed height of the retaining walls ranged from 3 to 15 feet. This paper focuses on the design and construction of the retaining walls for the project.

Jan 1, 2019

By A. Daugiala, D. Coleman

In 2014 the New York State Department of Transportation (NYSDOT) awarded a Design-Build contract to the joint venture team consisting of Skanska which is the managing partner; Kiewit Corporation and Ecco III (SKE) and HNTB as the lead design firm. The design build team employed methods to provide schedule savings and commercial benefits to the owner NYSDOT. This paper presents the design approach and construction methods used to accelerate drilled shaft installation supporting the main span foundation for the cable stayed bridge. The drilled foundation contractor Underpinning and Foundation Skanska, a division of Skanska was responsible for assisting with design, budgeting and construction of the drilled shaft foundation construction. As part of the Request for Proposal (RFP) bid process, Alternate Technical Concepts (ATC) was encouraged by the NYSDOT. The JV team proposed an ATC which involved a scaled production shaft testing method to simulate the ultimate load level, commonly referred to as the “Chicago Method” was used in the rock socket employing the Osterberg Cell (O-Cell) testing procedures. To the authors knowledge this was the first NYSDOT project where this approach was utilized on a Demonstration/Production installation to validate construction procedures and load bearing capacities. Construction procedures, challenges and solutions are discussed in detail. Upon completion of successful drilled shaft construction, concrete integrity is verified using two methods – Cross Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP). A comparison from the contractor’s perspective is provided. Finally the drilled shaft rock socket is tested to ultimate end bearing values while rock socket side shear stresses are not exceeding the service level loading. Lateral load test was also a RFP requirement; the test arrangement and performance are discussed in detail as well. The Kosciuszko Bridge location poised unique geotechnical challenges on many levels shifting towards an extreme boundary of parameters encountered in New York City Area for drilled shaft construction. The JV team and specialty drilled shaft contractor actively participating in the shaft design and construction practice coordination and working with NYSDOT yielded a successful foundation solution which provided cost and schedule savings to the project.

Jan 1, 2016

By Jeffrey M. Taylor, Arturo Ressi di Cervia

"Construction of the drilled shafts for the Brightman Street Bridge Replacement Project were not only challenging due to working over the water but were also challenged by changed soil conditions, concurrent work being performed by an adjacent contractor on the same project, environmental restrictions and severe winter conditions. A total of 36 x 8 foot (2.44m) diameter drilled shafts with 7.5 foot (2.31m) rock sockets were installed for the East and West bascule piers. This project also included Osterberg Cell load testing on two production drilled shafts at both the East and West bascule piers. The results from the load test program were used to fine tune the design of the drilled shaft rock sockets. From a constructability standpoint the reverse circulation drilling method with a pile top drill rig proved to be an excellent choice for drilling the overburden and rock sockets of the large diameter deep drilled shafts. INTRODUCTIONThe replacement Brightman Street Bridge spans the Taunton River between Fall River and Somerset in Massachusetts.The new crossing is located approximately 1500 feet (450m) upstream from the existing Brightman Street Bridge, which was built in 1908. The new mainline bridge includes nine spans totaling 1725 feet (525m). A bascule type moveable span will be located in the middle of the Taunton River and provide a 200 foot (61m) open channel centered about the 400 foot (122m) navigational channel. The bascule span, which has a span length of 409 feet (124.7m), will be a trunnion-type four leaf structure with a solid deck. A site plan is shown in Figure 1 Contract 3, which includes construction of the foundations for the East and West bascule piers, was bid on December 19, 2000 and was awarded to Modern Continental Construction Company (MCC) on January 24, 2001. MCC in turn awarded the subcontract for the installation of the drilled shafts to TREVIICOS Corporation, which started mobilizing in June of 2001.The scope of work for the drilled shafts of Contract 3 consisted in installing 18 drilled shafts in three rows on each side of the river to support the bascule piers located in the middle of the Taunton River.The foundation plan for the bascule span is shown in Figure 2."

Jan 1, 2004

By Amr Sallam, Ahmad Mohamed, Mohamed Alrowaimi

Renewable energy, in the form of wind and solar, has emerged as main source of energy in the modern society. The wind industry has substantially grown over the last two decades to become a key player in providing energy to public. Wind turbines are getting larger, taller, and more efficient every year. The foundation is a major component of the wind turbine system. The wind turbine foundation must provide short and long-term stability for the overall turbine to allow continuous and safe turbine operation for energy production. The turbine serviceability and stability requirements must be geotechnically and structurally satisfied. In North America, major foundation types currently utilized in the wind industry include gravity spread foundation, mono pier foundation, and pile foundation. In this case study, a Post Tensioned Pile Cap (PTPC) foundation was used to support a 3.15-3.4 Megawatt turbine with 125M Rotor supported on 87.5M-hub-height tower. Soil anchors in the form of Auger-Pressure-Grouted-Displacement (APGD) piles and Continuous Flight Auger (CFA) piles were utilized. Four distinct subsoil conditions were identified, and for which four pile designs were adapted. Due to the occasional encounter of stronger soils at 50 to 55 feet (15.2 to 16.7 m), shorter pile design was preferred. To satisfy the design uplift load, pile post grouting were utilized to increase the shaft capacity of the piles. In this paper, the pre-production pile load test program will be described. The pile load test procedure, analysis, and results will be presented. A discussion will be provided, which led to the selection of the optimum pile design to support the high tension loads taking into consideration pile length limitations.

By David Pierce

The Port of Seattle, one of the largest on the west coast of North America, made a strong statement regarding their support for reusing existing structures when a decision was made to rehabilitate Pier 69, on Seattle&apos;s downtown waterfront, for their new headquarters. Because of its age and location, the pier provided an unusual challenge to the Port and its consultants. The Port hired Peratrovich, Nottingham, and Drage Inc. to design the seismic strengthening of the pier itself. To remedy the lack of seismic resistance in the 70-year-old pier, PN&D designed a new steel-pipe-pile supported concrete apron next to it. The structure relied on a development by PN&D, the "spin-fin pile", to achieve the tension capacities required of the batter piles. The construction of this apron was completed in October of 1991. Another team of consultants performed the superstructure renovation design, which is now under construction.

Jan 1, 1992

By Schmitz Stefan, Stephan Jee-Sun

"Due to the reunion of Western and Eastern Germany in the late 80’s, a multitude of infrastructure projects had to be executed. A good portion of these projects required improvement of the motorway system. In the southern region of Leipzig, in the eastern part of Germany, it was required to connect two existing motorways. Parts of the new motorway pass old strip mining areas. These strip mining areas consist of up to 70m thick backfill material. Especially the upper 20m are very inhomogeneous soil material with a very low bearing capacity. In order to increase the bearing capacity, to decrease the differential settlements and to homogenize the soil parameters, soil improvement using sand-gravel columns was required. Bauer Spezialtiefbau GmbH executed the installation of approx. 711,000 linear meters of columns with a length from 5 m to 25 m. For the project, 11 rigs with frame leads up to 40m were used to install the 43,000 columns with a diameter of 0.8m in 27 weeks.1. INTRODUCTION1.1 Site LocationThe construction site is located in the south-eastern part of Germany, in the south west of the city Leipzig.The area to be treated had a size of approx. 500,000 m² to allow the construction of dam/embankments and a highway bridge.1.2 Required WorkIn addition to the general earthworks and the installation of geogrids and fibre mats, a total amount of more than 710,000 linm of Gravel-Sand Columns with different lengths due to the given soil conditions had to be installed:•nos. 4,206 Columns length 5m ? 21,030 linm•nos. 4,581 Columns length 10m ? 45,810 linm•nos. 10,820 Columns length 15m ? 162,300 linm•nos. 19,634 Columns length 20m ? 392,680 linm•nos. 3,574 Columns length 25m ? 89,350 linmFor the installation of the columns Gravel-Sand with the grain size of 0/32mm was used. The total amount of Material was 580,000mt"

Jan 1, 2015