Search Documents

By Arthur Brant

STEEPROCK LAKE (Figure 1) lies about two miles north of Atikokan, a village approximately one hundred and forty miles west of Fort William and one hundred miles east of Fort Frances on the Canadian National railway. The possible presence of hematite beneath the waters of Middle arm was inferred by early geological investigators (1890-1903) from the dense hematite float found on the southerly shores of this portion of the lake (1). A dip-needle survey of Middle arm, undertaken in the winter of 1930-31 by J. G. Cross, indicated two areas of high magnetic attraction which Mr. Cross thought might be due to magnetic iron oxides associated with possible hematite bodies. Bedrock could not be reached by the ineffectual hand-drilling so courageously attempted, and further work was abandoned. It was not until 1937 that Mr. Jos. Errington, of Toronto, convinced of the possibilities, determined to support Mr. Cross to the extent of several thousand feet of drilling. During the winter of 1937-38, holes Nos. 1, 3, 4, 5, and 13 were put down (see Figure 1). The first four of these holes demonstrated that the areas of magnetic attraction outlined by the dip-needle survey east of the Narrows and southwest of Elbow point were due to ash rock (2). As a result, Mr. Cross decided to investigate the bordering areas of low magnetic attraction and selected a location near the high ferruginous lime (3) point in the northeast of Middle arm. Dense, hard hematite beneath approximately 350 feet of water and clay was struck in the first hole, and, before the end of the winter's drilling, hematite had been encountered in holes Nos. 6 to 13 along a straight line 700 feet in length (see Figure 1). In the meantime, the Steerola ( 4) Exploration Company had been formed to continue development and already, in the spring of 1938, W. D. Neeland, the Company geologist, had come to the conclusion that the most probable location for possible hematite was at the ash-lime contact. Accordingly, during the summer, drilling was continued off-shore in holes Nos. 15, 25, and 27 (see Figure 2) toward possible hematite bodies inferred by Mr. Neeland.

Jan 1, 1940

By M. Bustin, A. Hosseinian, G. Preisig

Hydraulic fracturing and hydraulic shearing techniques are essential for the development of unconventional oil & gas and geothermal resources. Such techniques will also play a key role in the development of CO2 sequestration, and management of high stresses encountered with deep mining. However, the optimal design of hydraulic injections is often limited by continuum treatments of the rock mass without consideration of the influence of the natural fractures present. These may interact with the hydraulic fracture to promote offsets or arrest, or may cause the natural fractures to undergo shear and dilation. Given the limited access to the rock afforded by deep boreholes common to oil & gas and geothermal projects, advanced numerical modeling is critical for understanding key mechanisms and interactions. In this work, we first present a coupled hydromechanical distinct-element model focusing on the propagation of a hydraulic fracture. Normal and shear displacements arising from the generated hydraulic fractures are subsequently integrated into a fracture flow model for detailed analysis of specific flow behaviour and fracture permeability. For this, a scanned 3-D profile of a natural fracture is used to correlate surface roughness to dilation as a function of shearing. Fracture flow is computed at different time steps corresponding to different fracture propagation states and geometries. Modeling results indicate that the opening of a tensile hydraulic fracture is accompanied by millimetre-scale shear displacements associated with slip and wedging between adjacent blocks. This may leads to a mismatch between the upper and lower walls of the fracture if asperities are irregular and strong enough. However, fluid-induced tensile fractures have low Joint Roughness Coefficients (JRC), and associated millimetre-scale shear displacements are too small to ensure a significant offset of asperities that prevent a fully-elastic closure when the hydraulic fracture is depressurized. Injection of proppant is thus critical to keeping hydraulic fracture apertures open. Future work is planned that will see the models calibrated against field data including microseismic event locations, magnitudes and source mechanisms, tiltmeter deformations, stress change, and pore pressures.

Jan 1, 2015

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By M. Turek

Cost management in the conditions of increasing competition and unforeseen market turbulence constitutes one of the key areas of the enterprise?s activity. In the last two years the demand for hard coal on the domestic and global market of non-renewable resources has increased significantly. Polish hard coal mining industry, as an industry in the stage of decline, received a chance for rejuvenation. However, one of the most significant conditions of seizing this opportunity is the rationalization of mining costs and improvement of production effectiveness. Due to the significance of this issue, the main objective of the paper is to identify the possibilities of improving the production effectiveness in the hard coal mining industry. In order to meet such an objective, in the first part of the paper we measured effectiveness in the Polish hard coal mines in years 2006- 2011. The research encompassed three out of five mining enterprises operating in the country. Then based on the received results, guidelines concerning the improvement of effectiveness of production were created, taking into consideration infrastructural, technical, economic and organizational determinants. Furthermore, opportunities and threats for improving the production effectiveness, stemming from the external conditions have also been indicated.

Aug 1, 2013

By M. Mai Manga, M. Renaud, A. Faucher, C. Bazin

ABSTRACT Grinding circuits are operated in the presence of disturbances resulting from ore changes and equipment malfunctions, such as hydrocyclone overloading, worn or partly plugged apexes, surging, and internal liner detachment that may cause a loss of classification performance. Metal recovery losses in downstream leaching or flotation circuits justify the development of methods for rapid detection of hydrocyclone malfunction. Two methods are presented in this paper. The first method uses measurements from sensors available in a grinding circuit and the second uses vibration sensors installed on the individual hydrocyclones of a nest.

Jan 1, 2011

By I. Yutronic

Compañía Minera Doña Inés de Collahuasi's (CMDIC) Concentrator Plant is located at 4300 meters above sea level, approximately 2000 kms north from Santiago, Chile. The concentrator has three grinding lines. Each one, Lines 1 and 2, have one SAG mill at the primary grinding stage followed by a secondary grinding and classification stage consisting of one ball mill, two hydrocyclone batteries and a sump with two pumps. Line 3 has one SAG mill (Gearless Mill Drive), followed by a secondary grinding and classification consisting two ball mills, four hydrocyclone batteries and a sump with four pumps. Average throughput for these three lines is 150 Ktons per day. Peak values of 180 ktons per day have been achieved. Since late 2008 and throughout 2009 and 2010, Operations and Automation areas developed an optimization program for the grinding process, considering the implementation of Model Predictive Controllers (MPC) for the three SAG mills, and later, extending MPC to the secondary grinding and classification stages. The implementation of a MPC solution was based on stability considerations (high variability of the SAG process, high interaction between sump level control and classification efficiency, etc), requirements for an automated and consistent operation, the need to maximize throughput under timevarying scenarios and, in the long term, optimization of grinding process considering Specific Energy Consumption, among other parameters. MPC solutions had proven control robustness and strong optimizing capabilities in terms of helping in discovering new operational points and so achieving all of the aforementioned goals. On the first stage of the program, MPC implementation considered identification of dynamical process control models based mainly on historical data, in order to know the impact of a group of Manipulated Variables over Controlled Variables. Also, the impact of measured Disturbance Variables was modeled in order to take into account the high impact and interaction of these variables over the processes. At the end of this stage, 4 controllers were successfully operating for the 3 SAG mills and the secondary grinding and classification process. In response to challenges made by the working group, the second stage of the development of control applications in the grinding process required to achieve a design and implementation of a solution capable of governing the milling process, in addition to stabilization and optimization of both processes (SAG milling and secondary grinding), to integrate from a point of view of process control and automation. Therefore, in the second stage, MPC performance was continuously monitored and optimized through advanced tuning, inclusion of more process models (with proper step tests), redefinition of specific optimization criteria and adjustment to new process needs. Finally, successful MPC implementation at Collahuasi has proved that fast development and deployment of process control solutions is possible and allows immediate process stability, higher throughput, specific energy consumption reduction, and successful product size control, among many others.

Jan 1, 2012

By D. F. Malan

"This document highlights some of the topical problems associated with the design and support of deep tabular excavations in hard rock. The displacement discontinuity boundary element method has been used for at least five decades to analyse stress and displacement distributions around narrow width excavations with complex plan outlines. The assumption is made in most cases that the rock mass surrounding the excavation is perfectly elastic. Although this approach works well to minimise stress concentrations in practice, it has limitations as important parameters, such as the effect of mining rate, cannot be investigated. Recently, a limit equilibrium model has been studied as a means to enhance standard layout design exercises by including an interactive on-reef damage model. This approach can include explicit energy release dissipation computations. A second problem faced by engineers in the mining industry is the evaluation of pillar and remnant stress. The paper highlights two aspects namely the effect of element size in displacement discontinuity modeling on pillar stress and the difficulty to estimate the effect of total closure on the regeneration of stress in old mining areas. Regarding the support of the tabular excavations, current efforts are focussed on providing improved aerial coverage using hangingwall bolting and temporary nets. An unresolved issue is the installation of permanent mesh in low stoping width areas. INTRODUCTIONSince 1886, more than 50 000 tons of gold has been mined in the Witwatersrand Basin of South Africa (Hartnady, 2009). The nearby platinum mines also saw significant growth in recent years and more than 80% of the world’s platinum group metal reserves are contained in the Bushveld Complex of South Africa (Nell, 2004). Apart from the economic aspects, the mines served as an outstanding rock engineering “laboratory” for many decades owing to the deep, tabular nature of the excavations. The period from 1960 to 1980 was especially lucrative in terms of research and world-renowned researchers investigated the support and rockburst problems (e.g. see Cook et al., 1966; Salamon, 1968; Bienawski, 1973; Wagner, 1984). Many of the rock-related problems nevertheless persist up to the present day and this paper explores some of these problems and recent progress. The production of gold declined substantially in recent years (Hartnady, 2009) and well-directed rock engineering research can play a meaningful role to slow this trend. The objective of the document is to highlight critical areas requiring additional research and not to discuss the topics in detail. The reader is referred to the many references for additional information. The paper only focuses on three areas namely numerical modelling, pillar stress estimation and aerial support. Although these are diverse topics, it is included in one paper to illustrate the many unsolved and practical problems associated with deep tabular excavations."

Jan 1, 2015

By Mario Bergeron

L'exploration géologique pour les EOP (EOP: platine, palladium, iridium, osmium, ruthénium, rhodium) requiert avant tout des méthodes appropriees à la mesure de ces élémenIs. L'approche analytique choisie doit tenir compte de plusieurs facteurs, les plus importants étant: le type de materiel analysé, sa representativite, la sensibitite de la methode et les cotits reliés à son utilisation. Dans cette optique, plusieurs démarches ana/ytiquessont possibles, toutes requérant une étape de préconcentration. L 'une des plus adéquate consiste à effectuer une préconcentration par fusion plombeuse suivie d'une analyse par émission au plasma, cette procédure permettant de mesurer Ie platine, la palladium et Ie rhodium à des couts compétitifs (15 $/échantillon). Advenant 10 presence de teneurs appréciables de l'un ou plusieurs de ces éléments, une préconcentration par fusion au sulfure de nickel suivie d 'une analyse par activation neutronique assure alors la mesure de tous les EGP ainsi que celie de l’or (90 $/échantillon). Il est important de noter que Ie nickel, ades teneurs superieures à 4%, interfère au cours de l'étape de préconcentration par fusion plombeuse, ce qui se traduit pas sous-dosage des concentrations en platine, effectivement presentes dans l'échantillon. Ainsi, les géologues à la recherche d'EPG dans des environnements géologiques riches en nickel devraient s'assurer que l'analyse utilise, au cours de l'étape de préconcentration, une fusion au sulfure de nickel.

Jan 1, 1990

By B. R. Rakishev

When transferring from the railway transport to the combined automobile-conveyor transport by stripping works at coal mines, it was proposed to form at the working zone a concentration horizon for reloading part of the stripping volumes at the railway transport. The procedure is adduced for substantiating parameters of bloc-panels, depending on the step of transferring of reloading points in interrelation with the intensity of the working zone?s development with observing the balanced movement of parts of the stripping zone relative to the temporary concentration level.

Aug 1, 2013

By D. Ling, Santos. R. M., T. Van Gerven, M. Guo

The valorization of alkaline waste materials from thermal processes utilizing intensified mineral carbonation routes is investigated. The principal advantages of this approach are the chemical stability and storage safety of mineral carbonates, the opportunities for process integration presented by the technology, and the potential for conversion of low-value materials into useful products. Treatment and disposal of steel slags are a costly burden on steel plants. Sustainable solutions for Argon Oxygen Decarbonisation (AOD) and Continuous Casting (CC) stainless steel slags and Basic Oxygen Furnace (BOF) steel slag are desired. An integrated on-site mineral carbonation approach is envisaged as a favourable solution.

Jan 1, 2011

By D. A. Le, T. S. Nguyen

"In Canada and other countries, several types of rock formations are being considered for the geological disposal of radioactive wastes. In order to better understand the ability of these rocks to contain and isolate the wastes, the Canadian Nuclear Safety Commission collaborates with different international research organizations and has access to experimental data from Underground Research Laboratories (URLs) in the world. Such an URL is situated in Opalinus Clay, at Mont Terri, Switzerland. An experiment, consisting of the excavation of a tunnel followed by water and gas injections in a test section of the tunnel, was performed at the URL. The authors have developed a mathematical model, based on the poromechanics theoretical framework, to simulate those phases of the experiment. The constitutive relationship for the stress-strain behaviour of Opalinus Clay takes into account its inherent anisotropy due to bedding. The model was able to capture the main features of the experiment such as the prediction of the shape and extent of the excavation damage zone and its influence on water and gas migration.INTRODUCTIONIn Canada and many other countries, several types of rock formations such as crystalline rocks and sedimentary argillaceous rocks, are being studied for the disposal of used nuclear fuel from nuclear power plants. Geological disposal relies on multiple natural and engineered barriers for the long-term containment and isolation of the wastes. The host rock is a major natural barrier and is the subject of extensive research. The Canadian Nuclear Safety Commission (CNSC), Canada’s nuclear regulator, will be responsible for the licensing of future deep geological repositories. In order to evaluate the safety of deep geological repositories, CNSC staff keep abreast of scientific developments by collaborating with national and international partners on experimental and theoretical research on the long term performance of those engineered and natural barriers. Through that collaboration, the CNSC has access to data resulting from experiments performed at different Underground Research Laboratories (URLs)."

Jan 1, 2015

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By Mengsu Hu, Yuan Wang, Jonny Rutqvist

Material interfaces and typical boundary conditions are boundaries influencing the existence, uniqueness and stability of numerical solutions of water flow in heterogeneous media. The Numerical Manifold Method (NMM) with a two-cover-meshing system is an ideal method to handle boundaries, considering its flexibility with no need to adjust mathematical nodes onto boundaries, the meshing efficiency, and its integration precision. In this study, we derive and compare two new approaches for boundary constraints, i.e., a discontinuous approach with Lagrange multiplier and a continuous approach with jump function in the frame of NMM. In the discontinuous Lagrange multiplier method (LMM), Dirichlet boundaries or the material interfaces are regarded as discontinuities which are linked by Lagrange multipliers. In the continuous Jump function method (JFM), the material interfaces are regarded as inner interfaces, where the refraction law is realized by constructing jump terms with discontinuity of hydraulic gradient in its normal direction. Both the continuous and discontinuous approaches make full use of the aforementioned advantages of NMM and are established based on a clear physical meaning of water flow by our energy-work seepage model. The newly derived boundary-constraint approaches were coded into an NMM water flow model and tested for precision and efficiency on different simulation examples. We first tested both LMM and JFM for an idealized heterogeneous model, comparing the numerical results with analytical solutions. Then we tested both approaches with a heterogeneous model and compared the results of hydraulic head and specific discharge. We proved that both approaches are very suitable for material boundaries considering the accurate realization of the boundary constraints and the flexibility with no need for mesh-conforming.

Jan 1, 2015

By Mark Kennedy, Allan MacRae, Cameron Hams

New technology projects, particularly those involving first-of-a-kind metallurgical facilities, have a poor track record of achieving their overall financial targets, as they incorporate technological risks in addition to normal project risks. Traditional project management tools focus on risk from concept development through implementation, but typically fail to address the additional risks associated with a new technology project including slow start-up, slow ramp-up, and failure to achieve design performance (quality or throughput). These additional risks affect future cash flows produced by the project and hence its value, typically measured as net present value (NPV) or internal rate of return (IRR). Common accounting practice is to reduce the present value of future cash flows by applying a chosen discount rate, often reflecting the corporation's cost of capital. This discount rate does not contain an allowance for technological risk, which is often underestimated or misunderstood by both the financial and engineering project managers. This paper will focus on the topic of project risk and new technology, and how these play a role in the probability of achieving the predicted future cash flows. By properly addressing technological risk in the form of risk-weighted returns, marginal projects can be prevented from proceeding, while sound projects can be given the additional time and resources required to achieve the optimal level of front-end-loading (the level which returns the maximum risk-weighted net present value). A simple set of mathematical tools should enable engineers and financial professionals to establish a common level of understanding, thereby leading to a more accurate assessment whether a new technology project is ready to pass through its next level of approvals.

Jan 1, 2011

By Carrasco .. P. J. A., R. Parada, I. Saavedra, F. Parada, R. Parra, E. Balladares

In most of the smelters, the management of flue dust has a double objective: the control of minor elements in the anodes and the management of volatiles compounds that can cause contamination due to fugitive gas emissions. This is a special concern when high content of Va elements (As, Sb & Bi) are present in concentrates. We present the results of the experimental study to prove the principle of a novel process that recovers, via volatilization, the As, Sb and Bi in the flue dust as gaseous sulfides, due to a previous sulfidization. In the case of as control any further classical treatment for its stabilization is possible from the gas. The clean calcine can be returned to the smelter avoiding any concentration of these minor elements in the circuit. This process is now tested at pilot scale and shows better indices on carbon footprint than the classical hydrometallurgical process for flue dust.

Jan 1, 2011

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

By G. Marchand, R. H. Hay, E. C. Pearson

"AbstractA polishing .technique is described together with two anodic etching methods for aluminum and its alloys. Some of the optical and structural characteristics of the film formed by •these etching methods are discussed and it is shown to what degree these properties of the film are related to the crystallographic orientation of the metallic substrate. Applications to the study of recrystallization and twinning phenomena and to the study of plastic deformation, banding, and texture estimation are discussed. Micrographs are shown .to illustrate the manner in which the technique is particularly well suited to the study of such phenomena.IntroductionThe physical metallurgist is constantly faced with the problem of polishing and etching of metallic sections. Mechanical polishing is tedious, time consuming, and not applicable whenever a surface entirely free from plastic deformation is required. Etchants are generally required to reveal the grain structure in order to determine its size, shape, and regularity, or to bring up constituents. In the case of aluminum, the .most common etchant to reveal grains is a mixture of three acids: HC1, HN03, and HF. This etchant is fairly satisfactory on certain alloys and for certain metallurgical conditions but in general fails to give a good definition of the grain on castings, on highly alloyed products, and whenever the grain is smaller than 100 microns in diameter. Besides size and shape, a grain, or crystal, has an orientation and may be endowed with several types of imperfections."

Jan 1, 1952

By G. W. H. Norman

"During the past few years emphasis has been placed on the importance of major faults, fault zones, and associated structures in localizing ore deposition. This interest has developed partly through experience in mining camps in other parts of the world, and partly by the discovery of such structures associated with ore deposits in the Abitibi region, northwestern Quebec. The recognition of these structures has been brought about chiefly by detailed mapping that has been gradually extended along most of the southern gold belt of Quebec and across adjacent parts of Ontario. In the Chibougamau region of northern Abitibi, progress has been made in mapping major faults by using aeroplane photographs with a scale of about 1,000 feet to 1 inch for field mapping. These studies have shown that many large faults occur in the Abitibi region; also that there is a relationship, direct or indirect, between faults and mineral deposition. The faults are, however, of more than one type and age, and this should be clearly appreciated in any planned programme for prospecting this great region adequately.Geology of the Abitibi RegionGeneral GeologyFaults of more than one age and type occur in the Abitibi region. In order to appreciate some of the age relationships of the faults, a brief summary of the historical aspects and major structural features of the geology (fig. 1) is necessary. These historical aspects may be briefly summarized in chronological order as follows:(1) Accumulation of Archæan lavas and associated pyroclastic rocks, either alternating with, or essentially followed by, deposition of sedimentary rocks, and interrupted at least once by local and perhaps regional folding and erosion."

Jan 1, 1954