Search Documents

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By Kershaw M. G, Maughan R. C A

A process for eliminating nickel from electrolytic zinc plant solutions by precipita- tion with dimethylglyoxime (DMG) was developed to enable the Electrolytic Zinc Company of Australasia Limited (EZ) to treat nickel-bearing zinc dust precipitates. These precipitates are leached to recover their Cd and Zn content. The final Zn bearing solutions contain relatively high Ni concentra- tions (20-100 mg/1) and are treated with DMG and then neutralized to pH 4.6-4.8. The pre- cipitate is filtered off and the solution returned to circuit. DMG consumption is about 200% of theo- retical requirement, and Ni removal is 80% complete overall.

Jan 1, 1977

By James D

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Ltd has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the west coast of the -South Island, New Zealand.The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilizing spiral, wet magnet, high tension and plate electrostatic separators have been G47designed to produce ilmenite from the ore. Studies to utilize the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By Corbett GJ

Comparisons between individual SW Pacific Rim gold deposits have facilit-ated proposal of a new classification of porphyry-related mesothermal gold deposit types. Carbonate base-metal gold systems form at relatively high crustal levels, peripheral to porphyry intrusions. There is a spatial assoc-iation with major structures which focus fluids from degassing porphyries at depth. Milled matrix intrusive breccias and extrusive maar volcano/ diatreme breccias form as a result of pre-mineralisation phreatomagmatic eruptions. These focus degassing magmatic fluids by the provision of fracture ground preparation, typically within competent host rocks, adjacent to the breccia bodies. Local dilational structures control the form of individual deposits which may contain bonanza gold grades at sites of fluid quenching and/or repeated mineral deposition.Early quartz veining and porphyry-related alteration is common and later gold mineralisation typically occurs in association with carbonate veining and Fe and base metal sulphides as Zn > Pb > Cu. The progressive cooling by mixing of the upwelling mineralised magmatic fluid with descending bicarbonate waters, produces characteristic zonations in carbonate compositions. These vary with distance from the porphyry source, from Ca through Mg, Mn and distal Fe types. Gold mineralisation is preferentially distributed within the Mn/Mg carbon-ates.

Jan 1, 1994

This paper describes an ongoing study into the management systems developed by mining operations in Papua New Guinea to address particular public health issues in the workforce (primarily communicable and lifestyle diseases). The first stage of the study involves the analysis of the site health and safety management system documentation of three major mining operations in Papua New Guinea, producing a descriptive summary of each system. In the second stage of the study these summary descriptions are evaluated using a maturity model constructed through a detailed review of literature. Experience with the evaluation process is then used to refine the maturity model. The analysis performed in the study is used to develop a process for creating a maturity model for mine site health risk management based on a theoretical risk management framework, and refining it through empirical evaluations of the actual systems in place on site. Companies can use maturity models as a guide to organisational improvement, which in the context of the study will assist the operations in developing their systems for the management of health both in their workforce and in local communities.

Jan 1, 2007

Maintaining and improving the economics of open pit mining in the future requires understanding of the characteristics of open pit mining that are different to other mining or business activities, designing mines in the first place to be less susceptible to changes in these important characteristics, and adopting strategies which yield reliable returns despite unforeseen change. Planning and production personnel require guidelines and performance standards that are based on sound economics not solely on production criteria. The guidelines adopted for long-term implementation must assume a declining price for mineral products along with declining real costs, with research efforts directed at development of both evolutionary and revolutionary ideas aimed at implementation. Decision-making must focus on risk and probability criteria rather than just simple return-on-investment criteria, and the approach for management of personnel must support the higher level of communication essential for fast decision-making in the new environment of continual change.

Jan 1, 1992

The Regional Development Council has initiated a project that aims to find better ways for further investment by extractive industry companies in sustainable regional and community futures. It will be undertaken through collaborative actions that bring together the resources of private and public sector stakeholders in regional Western Australia.   The broad objectives of the project are to: describe and analyse the current situation with respect to the impediments to regional communities being more self sustaining, assess the effectiveness of the current and possible future levels of investment by extractive industry companies in the sustainable development of communities in regional Western Australia, identify and demonstrate collaborative ways in which extractive industry companies in Australia and other countries can play an enhanced role in sustainable regional and community sustainability through strategic engagement and investment; and confirm the effectiveness of the collaborative measures in delivering sustainable outcomes for regional communities by way of attracting and retaining populations and enterprises in Australia and similar environments.

Jun 1, 2010

This paper reviews factors involved in the feasibility stage of underground mine project development. Emphasis is placed on the need to first select the best method of extraction and make the most accurate assessment of the expected output even with the uncertainties which may exist in structural interpretation, ground stress, geotechnical factors, and industrial conditions. The subsequent engineering planning should be undertaken from the point of view of the face requirements and is subject to constraints imposed by the method of work and nature of the deposit and, in the case of access, to surface constraints and services.

Jan 1, 1983

By Phillips D. N, Herbert H. K, Fletcher A. C, Lewis R. K

Quartzite is a common feedstock used for the production of silicon by reduction at high temperatures in a submerged electric arc furnace. Silica fume, formed as a by-product in this process, contains crystalline silica in the respirable fraction. The crystalline silica in the fume represents entrained quartz derived from unreacted quartzite raw material within the furnace. A knowledge of the fragmentation of quartzite feedstock, in response to thermal disaggregation in the furnace, is important in feedstock selection to help minimise (a) the amount of crystalline silica in fume, critical from an occupational health and safety perspective, and (b) impurity levels necessary to achieve the highest possible purity of product silicon. In this study, a series of quartzites has been assessed in terms of the above requirements and correlations drawn between mineralogical and chemical characteristics. Alkaline solubility correlates with grain-size and level of stored strain in the quartz matrix. Grain-size affects the surface area available for attack while stored strain enhances the chemical reactivity of the strained matrix as well as profoundly influencing the disaggregation and microfracturing characteristics of strained grains and, hence, available surface area for chemical reaction.

Jan 1, 1995

The Japanese Government promulgated the æLaw Concerning Special Measures Against DioxinsÆ on 16 July 1999 and it was enforced on 15 January 2000. This is a unique law specialised to protect the environment by the control of dioxin emissions from waste incinerators and several industrial processes. In this law, a few metallurgical processes other than waste incinerators are designated as æspecified facilitiesÆ emitting certain dioxins. Thus, emission standards for dioxins to the air were set for electric arc furnaces (EAF) for steelmaking, iron ore sintering, zinc recovery from EAF dust and aluminum recycle processes. In this paper, the inventory of dioxin emissions for Japan and the recent research and development to reduce emissions from those processes are introduced. Further, some details on the formation mechanism of dioxins and future subjects for effective control of their emissions are discussed.

Jan 1, 2002

UNLIKE coal mines, in which some form of artificial ventilation is rendered necessary by gases given off by the material mined and is also enforced by the mining laws of all countries, metalliferous mines have almost entirely relied on natural ventilation, viz., that due to the difference in temperature between the outside atmosphere and the mine air. In small mines natural ventilation has proved sufficient, but as mining proceeds at a greater depth, and where large ore bodies arebeing attacked the writer is of opinion that some means of artificial ventilation will be rendered necessary if only from an economic standpoint.The Broken Hill Proprietary Mine was one of the first metal mines to introduce a scheme of artificial ventilation on a large scale. In order to render the working conditions of the semi-friable stopes of Block 12 and the lower levels of Block 11 morecomfortable for the men at work in these places, in 1903 it was decided to install a fan to thoroughly ventilate these stopes. The fan chosen was a Capell double-inlet fan beltdriven from a steam engine: this engine was later on replacedby an electric motor. The fan was put in commission at the latter end of 1904; its principal dimensions are as follows: Length 6 ft. 6 in., diam. 7 ft., diam. of inlet 4 ft. 7i in. The fan is reversible, though this is a rather misleading term, asthe direction in which the fan blades revolve is not reversed...

Jan 1, 1921

By Edwards A. B

This paper presents the results of an examination of four samples representative of the low-lead matte, high-lead matte, lead speiss and antimony speiss, respectively, produced during smelting operations at Port Pirie Smelters. The investigation was undertaken at the request of the Broken Hill Associated Smelters Pty. Ltd., as part of the research programme of the Mineragraphic Section of the Council for Scientific and Industrial Research.Analyses of the specimens are as follows:-

Jan 1, 1949

Coal water mixture (CWM) is a mix of finely ground coal with water and a small amount of chemicals. It is a new way of transporting and handling coal. CWM can be transported, stored and burned like fuel oil in steam generating boilers. It also has some environmental advantages over both oil and bulk coal. A group comprising Ube Industries Limited, Nissho Iwai Corporation (both from Japan) and Coal & Allied Industries Limited has been working in Japan and Australia since 1987 on a joint feasibility study into the production, transport and marketing of CWM from Australia to Japan. The group has been studying the development of a large-scale CWM plant on Kooragang Island at the mouth of the Hunter River at Newcastle, NSW. The project concepts and engineering plans for the CWM plant are well advanced and other studies related to the project are continuing.

Jan 1, 1995

By Nowell SB, Cottrill DA

Host-rock - wallrock major and trace element geochemistry associated with epithermal gold mineralisation in the Hauraki Goldfield of New Zealand is poorly documented, even though rock geochemistry is a recognised tool in exploration. Such responses assist in recognition of the regional scale imprint of fossil hydrothermal activity, and indicate targets for detailed evaluation within these alteration zones.Recent investigation of gold deposits in the Waihi (Gladstone), Golden Cross (Empire), Thames (Waiotahi) and Coromandel (Tokatea) areas indicate enrichments of Au, As and Sb in the andesitic wallrocks hosting mineralisation. Of the other elements examined, Si, K and Rb are enriched, and Na, Ca, and Sr are depleted at all deposits. These trends are best developed in the vicinity of veining. In deposits with clay alteration dominating (Waiotahi and Tokatea) there is also depletion of Mg, Mn, Zn and Cu. Ba and Cr are variably enriched or depleted within different styles of alteration. Base-metal enrichment in the wallrocks is not a feature of Hauraki deposits.

Jan 1, 1990

Patterns of successful metallic mineral discoveries in Australia are analysed for the last three decades. A trend towards more discoveries of poorly expressed and blind ore- bodies is evident and can be expected to continue. Discoveries using traditional and conceptual geological techniques have proportionally declined but are expected to continue at a significant level for a decade or so. Improvements in the quality and numbers of geological exploration models and in the quality of available basic geoscience data have aided successful discovery in recent years. Although some orebodies for the Year 2001 have already been found maintenance of a strong mineral inventory demands that more and better geological models are applied. Empirical models need to be improved by critical multi- disciplinary integrated studies of mineral occurrence at all scales. New models can and will be developed by various means. If application of these models is made with all the innovation, initiative and unorthodoxy that can be mustered then new discoveries will result. Greater attention to the surface expression of orebodies will also lead to new discoveries. Review and follow-up of old data in the light of new concepts will provide yet another discovery route.

Jan 1, 1981

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

By O&apos, Malley G. B

The properties of bearing metals are of considerable interest to mine engineers, since continuous running of mine and mill machinery is of vital importance. Of the several available types of bearing metal, the low melting point lead or tin base alloys are most generally used in mining plant because of the ease of replacement and the possibility of remelting scrap metal from old bearings. The most valuable property of these "white metals," however, is the plasticity which gives a self-aligning character to the bearings, enablingthem to adjust themselves to inequalities which may exist at the time of fitting, or which may develop during running. The object of the present paper is to explain in general terms the physical structures of white bearing metals, and to point out that constitution rather than composition determines the physical properties of these alloys. The same, indeed, is true of most engineering alloys. In steels, for example, a change in the structure may affect the properties to a far greater extent than a change of chemical composition.Structural changes in steels are produced chiefly by heat treatment. In the case of bearing metals no good purpose is served by heat treatment; the microstructure is determined by the conditions of casting, and striking differences in constitution (and therefore in properties) are encountered in an...

Jan 1, 1932

By George G

The Circum-Pacific Map Project is a cooperative international effort to prepare and publish geological, geophysical and mineral resource maps of the Pacific Basin and adjacent land areas. Earth scientists representing 180 organizations from more than 40 Pacific Rim countries are participating in the work. The project is directed by a committee established 14 years ago as an activity of the non-profit Circuin-Pacific Council for Energy and Mineral Resources. Technical and cartographic support is provided by the U.S. Geological Survey. The Circum-Pacific Map Project is organized under five regional panels of experts on the geology and resources of the four quadrants of the Pacific and Antarctica. A series of five 1:10,000,000-scale regional maps and a 1:17,000,000-scale map of the entire Project area, the Pacific Basin Sheet, provide the cartographic base. Forty-eight individual sheets are planned and thirty have been published in eight different series, including base maps, geography, plate tectonics, geology, energy resources, mineral resources, tectonics and geodynamics. Additional special single-sheet thematic maps on the Pacific Basin base have been published and are planned for a total of more than 50 individual sheets.

Jan 1, 1987

By Miovski P, Hooft P. V

In the majority of recently commissioned gold mines granular activated carbon is used to adsorb gold from alkaline cyanide pulps or solutions. At the same time the carbon also adsorbs many other inorganic and organic species, most of which lower the activity of the carbon. Removal of these foulants is necessary before the carbon is reactivated and recycled. Standard practice for re- storing carbon activity involves high temperature treatment in a kiln - an apparently straightforward unit operation which is not always satisfactorily carried out. This paper presents the results of some fundamental work carried out on the thermal reactivation of carbon in a laboratory rotating pot kiln. The effects of temperature and steam addition on carbon activity were examined and compared with the activity of carbons obtained from a number of commercial kilns. Carbon was also reactivated using a small-scale Rintoul Furnace in which carbon was resistively heated by the direct passage of an alternating electric current. It was established that both elevated temperatures and the addition of steam to hot carbon generally enhanced its activity although peat-based extruded carbons responded a little differently to coconut shell types. Other measurements made included the weight loss and the hardness of carbons as a function of reactivation conditions.

Jan 1, 1987

By Nash B. G W

In June 1976 a 600'tonne/day manganese ore sinter machine, with on-strand cooling, was commissioned at the plant of Tasmanian Electro Metallurgical Company Pty. Ltd. at Bell Bay, Tasmania. This machine was installed in order to utilize manganese lump ore screenings generated in the preparation of raw materials prior to charging to the electric smelting furnaces at Bell Bay. Since commissioning, trial sintering of a number of different grades of manganese ore fines from Groote Eylandt Mining Company Pty. Ltd, has been conducted and suitable sinter has been produced from these different grades. The sinter produced is used as part of the furnace burden in both ferro manganese production and silico manganese production. The inclusion of sinter as part of the charge in the production of ferro manganese has considerably improved furnace operating conditions and performance.

Jan 1, 1977