Search Documents

By J. C. Yingling

[New stochastic process models are developed to calculate the probability of various fill levels in section feeders as a function of vehicle interarrival times, payloads and feeder-discharge rates. These models may be utilized to establish the minimum feeder-discharge rate necessary to prevent a feeder, with a particular surge storage capacity, from constraining the section's production rate. In addition, it is shown how the output from these models may also be utilized to calculate the probability of various flow rates at junctions in the conveyor haulage network, enabling one to size gathering belts. The model provides a basis for optimizing, (in economic terms) capacity specifications for feeders and conveyor belts in the materials-handling system by considering tradeoffs in the size of the two types of units.]

Jan 1, 1997

By Christian Divis

[ ]

Jan 1, 2002

By R. N. Hambright

Gaseous and particulate exhaust emissions are characterized for a 1200 Bhp two-stroke cycle diesel, a 1000 Bhp four-stroke cycle pre-combustion chamber diesel, and a 900 Blip four-stroke cycle, direct injection diesel using steady-state modal testing and a versatile exhaust dilution-collection system. In addition, a 1.50 Bhp four-stroke cycle, pre-combustion chamber, turbocharged diesel was characterized for use in experimental water injection evaluations. Water injection downstream of the turbocharger compressor and upstream of the turbocharger exhaust turbine are evaluated for their particulate removal effectiveness on the small turbocharged diesel engine. The water droplets are inertially separated using cyclone separators designed for minimum pressure drop and outsize, lip to 50 percent of the total particulate mass generated was removed using a combination of both inlet and exhaust water injection techniques.

Jan 1, 1981

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 150 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey (USGS) canvass of producers. Domestic production in 2005 was estimated to be 24.8 Mt (27.3 million st) valued at $176 million. This was based on a preliminary survey of the common clay and shale industry. The leading producer states, in decreasing order by tonnage, were North Carolina, Texas, Alabama, Georgia and Ohio.

Jan 1, 2006

By Xu Lin Sheng

During the mining course, when the roof above coal seams is constituted by thick and hard sandstone (conglomerate), sudden roof movements often take place with great force and de¬struction which is the biggest danger to the safety and production. Such sever movements of the roof in mining directly relate to the rock mechanical properties which are the main fac¬tors that influences the regularity of hard roof movement and its destruction form. A significient work and important technical way for applying rock mechanics into mining en¬gineering is studying the rock mechanics of the hard roof and altering some of the rock me¬chanic parameters which induce the improvement of the rock properties in order to efficiently control the movement of the hard roof.

Jan 1, 1989

By Roy S. Nutter

The automation of coal mining must occur in a manner that is economically beneficial to the industry and that enhances the safety of the underground and surface workplaces. The work at WVU over the last five years in applying expert systems and neural network controlled autonomous robotics provides the mining industry with tools that when properly applied should clearly lead to mine-wide management and operational improvements and should also contribute to a higher awareness of safety issues by all work crews. This work includes the development of MMSS (Mine Management Support System) and the detailed development of autonomous robotics utilizing neural networks for mining systems.

Jan 1, 1993

In mining industries, materials loading and handling costs represent a significant component of the total (capital and operation) costs. A variety of methods have been applied in surface mine equipment selection in order to select the suitable loading and haulage system with the lowest total cost. The optimal size and number of equipment calculation are very important task for mining engineering because loading and haulage equipment are major proportion of open pit mining cost. Capital and operating cost are considered in objective function with respect to interest rate, insurance and tax in non-linear form. Shovel and truck annual productivity constraint, fleet matching constraint and number of truck per shovel constraint are incorporated in this optimisation problem with continuous variables. This formulation will yield total cost minimisation per hour and good accuracy compared to previous methods.

Dec 6, 2010

In preparing a paper such as this it was thought that the Newstan Colliery Company Ltd., being comparatively new, would need some introduction to mining people in general.The Newstan Company was formed by the Joint Coal Board in December, 1948 during a period of acute coal shortages. The Company took over the holdings of what were known as the Olstan and Northumberland Collieries, situated at Fassifern, alongside Lake Macquarie and adjacent to the Great Northern Railway, within easy rail access of Sydney and Newcastle, as shown on the locality plan (Fig. 1).The Company was developed in order to produce steaming coal for the power house trade and has continued its activities in the steaming coal trade since its inception. The Olstan and Northumberland collieries were together producing some 300 tons per day when the Company was formed, and it was from this foundation that the colliery was built. The planned development of the Company has been along the lines of producing coal by modern, highly mechanised methods, together with the preparation of theproduct for the consumer, to the highest degree possible consistent with up to date methods.In the comparatively short time of 5t years the mine has developed from a small hand-won coal unit to a high capacity modern mine, one of Australia's largest producers, with an output capacity as high as 3,000 tons per shift.

Jan 1, 1954

By Philip A. Dirige

This paper presents the variability of responses of paste backfill specimens that have been prepared with varying binding agent and binder combinations, when subjected to uniaxial compressive strength testing. A testing program conducted for an underground operating mine to produce cost efficient paste fill recipes using four different binding agents, in various ratios and combinations, is presented to illustrate the responses. These binding agents are Normal Portland Cement Type-10 (NPC T-10), oxidation or sulphide attack resistant binder (Binder A), replacement binder B (Binder B), and replacement binder C (Binder C). The paste fill recipes were prepared at 2, 3.5 and 5% binder content at varying binder combinations, at fixed size and tested in a Material Testing System (MTS) under constant strain rate conditions following cure times of 7, 14, 28, 56, 90, 112, 180 and 240 days. The results of tests suggested that the strength data clearly shows a trend of increasing strength with increasing binder content but not necessarily cure time. It is noted that all the blends achieved dramatic increases in strength up to 28 days of cure and then either increased or decreased moderately beyond 28 days curing, depending on the binder content and binder combination. The moderate decrease is apparent for the 2% paste fill blends and in some binder combinations of the 3.5 and 5% blends, which indicated lackluster performance beyond 28 days curing. This lackluster strength performance indicated that the binder content and combination may not be sufficient for the paste fill to achieve complete hydration and acquire adequate strength performance beyond 28 days. This study indicated that economic paste fill recipes can be designed with confidence using affordable alternative binders. However, it is noted that these alternate binders cannot be used as stand alone binders but should be used in combination with NPC to facilitate hydration of the paste fill.

May 1, 2006

By Fernando Generoso Neiva Ferreira

O aumento crescente dos requisitos de segurança a serem atingidos pela indústria automotiva vem cada vez mais exigindo a utilização de aços com maior conteúdo tecnológico, que é o caso do aço bifásico (“dual-phase”), que são caracterizados por uma microestrutura ferrítico-martensítica. Neste trabalho, estudaram-se, em escala laboratorial, os efeitos das temperaturas de encharque intercríticas (750, 800 e 850°C) e distintas taxas obtidas por dois diferentes meios de resfriamento (ar e ar forçado) na obtenção de microestrutura bifásica a partir de dois aços laminados a frio “full-hard” (produzidos industrialmente), com micro-adições de Nb e Mo e diferentes teores de C e Mn. Utilizando ensaios mecânicos de tração, microscopia óptica (MO) e eletrônica de varredura (MEV), observaram-se as influências da temperatura de encharque e da taxa de resfriamento sobre as microestruturas resultantes e as influências da presença de ferrita encruada, dos carbonetos não dissolvidos e da morfologia da segunda fase sobre as propriedades mecânicas das amostras estudadas.

Aug 16, 2017

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By M Shaffer, D C. Grant, D J. Goudie, P Sylvester, C Voisey

Scanning electron microscope–Mineral Liberation Analyser SEM-MLA can be used to discriminate between hematite/magnetite in iron ores, but achieving backscattered electron (BSE) segmentation between the two minerals is difficult for particles =75 µm using typical preparation and analysis methods for the MLA based on a tungsten filament SEM (Quanta 400) with 25 kV high voltage. Preparing iron ore sample mounts using a slow-speed polishing method, and conducting the experiment on a field emission gun SEM-MLA (Quanta 650) with the high voltage (HV) setting lowered to 15 kV reduces instrument noise and results in very clean BSE images and segmentation. This method requires new X-ray standards to be acquired for each mineral identity at 15 kV because of major changes in the spectra at lower kV. However, once these X-rays are added to the mineral reference list, effective segmentation can be achieved and a proper analysis obtained.CITATION:Grant, D C, Goudie, D J, Voisey, C, Shaffer, M and Sylvester, P, 2017. Discriminating hematite/magnetite via scanning electron microscope–mineral liberation analyser in the - mesh size fraction of iron ores, in Proceedings Iron Ore 2017, pp 541–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T. M. Tharp

Attempts to analyze the stability of slopes, foundations and underground openings in discontinuously jointed rock have generally assumed full joint continuity or ignored the role of stress concentration at the tips of discontinuous joints. The most common approach in rock slopes is to consider a failure plane consisting of coplanar, but discontinuous joints separated by intact rock. The intact rock is assumed to fail in shear as a MohrCoulomb material and to contribute a strength component proportional to the fraction of the failure plane that is intact rock (Jennings, 1970). An alternative approach by Stimpson (1978) applies Lajtai's (1969) theory for shear strength of discontinuously jointed rock masses to slopes. Lajtai allows tensile failure in the intact rock of a composite surface. This theory yields lower shear strength than that of Jennings (1970) except in the presence of high normal compression, however it also fails to account for the stress concentration at the tip of a discontinuous joint. For a given slope geometry, stresses increase with slope height, but in both of these models rock mass strength is independent of size. A fracture mechanics analysis shows that particularly for small slopes, rock mass strength decreases with size.A continuous stepped failure surface produced by propagation of preexisting joints may develop at lower shear stress than pre¬dicted by the Jennings (1970) or Lajtai (1969) models. This fracture mechanics model applied to slopes in competent rock is more realistic in its assumed failure mechanism, and for large slopes more conservative than the Jennings (1970) or Lajtai models (1969).

Jan 1, 1984

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in this chapter is what is ordinarily termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

Any hypothesis for the origin of the Otago gold-quartz lodes must account for the following observations. 1. Southeast of Glenorchy, where the schists hosting the lodes are comparatively unaffected by Neogene Alpine Fault deformation, the dominant strike of the vein systems is NW-SE, parallel to the axis of greatest post-metamorphic uplift in the Otago Schist belt (Paterson, 1986). 2. The lodes are fault-hosted, with some developed along steep, low-displacement normal faults (eg Barewood, Bendigo, Nenthorn), implying NE-SW extension, and some developed along low-angle thrusts (eg Macraes) implying, in apparent contradiction, NE-SW contraction (Teagle et al, 1990). 3. The mineralising fluid was of metamorphic origin (McKeag and Craw, 1989), but while some of the lodes developed in a mesothermal environment at considerable depth (eg ~10 km for Macraes), others appear to have formed at very shallow depth (eg <1 km for Nenthorn) (Craw and Norris, 1988). 4. The timing of the mineralisation is generally poorly constrained but postdates the main Rangitata schist metamorphism. It probably initiated during early Cretaceous exhumation and unroofing of the schist belt (140 - 120 Ma?) and may have continued well into the Tertiary (Craw, 1989). Estimates for the relative ages of the different lodes are largely speculative but, based on pressure estimates from fluid inclusion studies, Macraes likely represents the deepest and oldest lode system while Nenthorn (just 12 km to the southwest) is perhaps the shallowest and youngest (Craw and Norris, 1988).

Jan 1, 1992

By Murali M. Gadde

Perimeter mining is a special form of very productive partial extraction method practiced at some mines in the United States. In the Illinois Basin mines where all major coal seams have weak underclay in the immediate floor, experience shows that any long-term ground control issues will arise due to floor failures rather than instability of the coal pillar itself. While there is a significant amount of work done on floor stability associated with regular pillars, no work has been done so far on the stability of perimeter pillars. This paper reports the results of a comprehensive study that was conducted for the first time on floor stability during perimeter mining in the Illinois Basin mines. A special plate template, which mimicked a common perimeter pillar configuration was created to conduct in-situ bearing capacity tests at five mines in three states of the Basin. Additionally, because of the complex shape of pillars created in perimeter mining that defies any closed-form solution, floor bearing capacity was studied using three-dimensional nonlinear numerical modeling. Based on these in-situ and numerical studies, some guidelines are provided for perimeter pillar stability analysis.

Jan 1, 2009

By M. Slatter

The need for anti-corrosion coatings has existed for many years in the ground support industry, but the application requirements have made coating selection limited. Varying groundwater and chemical conditions continually challenge long term coating performance. Traditionally the industry coating preference has been hot-dip galvanizing due to its performance characteristics in highly corrosive environments and low cost nature. However, the galvanized coating has application limitations. This paper highlights some of these limitations and provides selection criteria for a new organic coating developed for one such difficult application, DSI?s Omega BoltPTM Pwhich is an expandable ground support. [ ]

Jan 1, 2009

By L. J. Cabri, J. M. D. Wilson, R Lastra

An image analysis program can search for gold minerals in polished sections by scanning about 100 x 100 back-scattered electron images at a magnification of x400, allowing gold grains as small as 1 micrometre in diameter to be detected. Typically, a c.15 h overnight search of a product smaller than 45 micrometres will scan c.1 500 000 particles, providing data that are not easily obtained through manual operation of an optical microscope. The program locates grains of the correct brightness, acquires gold X-rays from them by wavelength-dispersive spectrometry, filters the data to remove artefacts and record the images and stage locations for subsequent retrieval. At the end of the run, the program allows the operator to verify and identify the grains found. Industrial studies at Canmet have included determining the nature of gold in cyanidation tailings, checking the mineralogy and size of gold grains in samples from an Indonesian Cu-Au concentrator and locating and measuring gold liberation and grain sizes in an ore

Jun 21, 1905

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By C. B. Manula

This report is volume 5 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Subsidence subsystem of the Master Design Simulator. This subsystem uses the finite element method to simulate ground movement caused by an advancing mining face in an underground coal mine. The model is structured around the concept that the ground mass is a layered media of different thicknesses and material properties. Gob areas are considered to be unfilled with broken rock at the beginning of mining. After mining starts, the gob areas are filled with broken material which provides resistance to the lowering of the overlying strata. The model is tied to the Geology and Reserves subsystem, but it can also operate as a free standing routine. A case study is presented illustrating the application of the model. A detailed user's manual, including a program listing, is included in the appendices.

Jan 1, 1974