Search Documents

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

Performance of Outotec FloatForce« Flotation Mechanism - A Study in Both Computational Fluid Dynamics and Industrial Scale Measurement

Sep 13, 2010

By Harold W. Lipper

BUREAU OF MINES helium plants produced a. record-breaking 477 million cubic feet of this essential element in 1959. The supply of helium was less than the demand before operations were resumed at the Navajo plant in July and begun Sit a. new plant at Keyes, Okla., in August. Helium was in abundant supply after August, and the informal allocation system which had been in use intermittently since 1955 was discontinued Delivery of 26 new tank cars in August and September increased the total in the tank-car pool to 163. Defense and space agencies and the Atomic Energy Commission continued to use more helium in their operations and research.

Jan 1, 1960

By Braden Lusk, Tristan Worsey, Nathan Rouse, Kyle Hall

Loading explosives up hole has challenges that are typically not seen in down hole explosive loading. Most explosives applications are not up hole. Lack of experience and technology can cause significant problems when loading explosives up hole. When results aren’t achieved, the blame is commonly put on the design when the true problems are unknown. Not knowing the cause of the problem causes drill and blast designs to be over engineered and very costly with little success. Being able to know and record key data is crucial to actually solving the problem. This paper goes over blast instrumentation that can be used to trouble shoot drill and blast problems in up hole explosives loading in underground mines. The tools and procedures used to trouble shoot include velocity of detonation recorder, borehole tracking, seismographs, and borehole camera. Each item will be discussed in detail with a case study to show the usefulness of the instrumentation. The operation discussed in the case study had issues pulling raises and had hang ups in the stope shots. These problems caused production slowdowns and costly remediation blasting that was not very successful. The case study is an underground gold mine that used modified sub-level caving with backfill as the mining method.

Jan 1, 2018

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By C. H. Lee, K. Adham, D. Lemieux, J. P. Mai, A. M. S. Hussein, S. Francey

Copper concentrates contain an increasing amount of arsenic, as the older sources of cleaner ores are depleted. At the same time, the market-determined price penalties on arsenic rich concentrates are rising due to limited arsenic treatment capacity at smelters and increasingly stringent environmental emissions limits, necessitating arsenic removal from the copper concentrates. Heating the concentrate to about 700°C can remove significant amounts of arsenic (as elemental and/or sulfide); however, it is important to achieve that removal economically and with due consideration to post-roasting arsenic (toxic waste) treatment. A comparison is made among different roasting options (kilns, multi-hearths and fluid beds) to qualify their potential application to arsenic roasting of copper concentrates. Both direct and indirect methods of heating as well as inert, air and oxygen atmosphere options are considered. Technology comparisons are made with respect to the roaster’s operation, its off-gas treatment and arsenic stabilization. INTRODUCTION In the last twenty years, the arsenic content in globally produced copper concentrates have risen steadily due to the depletion of cleaner ores and the increase in complex concentrate production. Smelter contracts typically limit arsenic to less than 0.5wt%, with a penalty paid per unit of additional arsenic and other contaminants such as antimony. While penalties can vary, they can be on the order of $70/dry metric tonne of concentrate per 1% of arsenic. Strategies used by miners to avoid the price penalties have been to blend clean and complex concentrates, and to remove arsenic from complex concentrates to achieve smelter limits. Arsenic can be removed from copper concentrates by the heat-induced decomposition of the predominant enargite mineral (Cu3AsS4) at ~700°C. Roasting at such elevated temperature is a commercially proven option, but still suffers from process, cost and environmental challenges. After roasting, the released arsenic sulfide fumes can be separated from most of the entrained concentrate dust in cyclones. Then, the As2S3 laden off-gas can be oxidized to generate a still volatile oxide (As2O3), which can be further separated from the residual concentrate dust in a hot electrostatic separator. Next, the off-gas can be cooled with air or water, to either deposit the arsenic oxide in a dry or dissolved state. Dissolved arsenic acid can be oxidized to As(V) and reacted with iron to yield a stabilized ferrihydrite precipitate or scorodite that can be safely disposed. In the case of dry arsenic trioxide, it can be mixed with reactants (e.g. iron) and fluxes before thermal stabilization in a glass matrix, thus eliminating the need for costly oxidation.

Jan 1, 2019

The Manto Verde mine is found in the coastal ranges of the Atacama desert, 1000 km north of Santiago, Chile . The deposit is a fault-breccia specularite-oxide copper mineralisation hosted by the Jurassic andesites of La Negra Formation. It is located in a tensional fault that joins twoparallel arms of the Atacama Fault. The mine is in feasibility study: reserves are of the order of 60 Mt at 0.9 wt per cent soluble copper; mining will be undertaken at a rate of 11 000 tpd utilising an open pit and the ore will be heap-leached with acidified sea water, with copper recovery and by SX/EW.

Jan 1, 1992

By A A. Ndiaye, A Galli

In a companion paper on current hedging practices in the mining industry (Armstrong et al, 2009) we showed that contrary to popular belief, mining groups are still using financial derivatives to hedge against foreign exchange risk and interest rate risk, and more recently against adverse changes in energy prices, notably the oil price. This paper presents a case study on a hypothetical gold mine to illustrate the impact that hedging policies could have on its profitability by reducing the downside risk due to adverse changes in the exchange rate and increases in fuel prices. The characteristics of the hypothetical mine have been set to reproduce those of a real gold deposit, the Kisladag mine that is currently being exploited by open pit methods in Turkey. This mine was selected because its feasibility study was available to the public. Geostatistical simulations are used to reproduce the inherent uncertainty on the recoverable reserves û stochastic simulations are used to generate the variability of the other three key sources of uncertainty: the gold price, the cost of energy and the exchange rate. A simple strategy based on straightforward vanilla options (puts and calls) was developed for hedging the last two risks, on the assumption that the company sells its production at the prevailing spot price.

Jan 1, 2009

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By Bauduin C. Besix

The Eurocode 7 "Geotechnical Design" is based on "Limit State Design", tackling the uncertainties as much as possible at their source through: - selection of characteristic values of variables (loads, soil properties, pile resistance,...); - partial factors applied on the characteristic values; - model factors to account explicitly for uncertainties of the calculation rule if necessary. Eurocode 7 will propose three "design approaches". The selection of one of them will be by National Determination. For pile design, the approaches are: - approach 1 is a "material factoring approach" at load side and a "resistance factoring approach" at resistance side. The structural and geotechnical design are checked for both of two separate sets of partial factors. - approach 2 is a "load and resistance factoring approach" and is in several aspects close to a deterministic approach. The design is checked for one set of partial factors. - approach 3 is a material factoring approach, at load as well as at resistance side. The design is checked for one set of factors. The aim of this paper is to introduce to the design of pile foundations based on pile load tests and on ground test results (semi-empirical and analytical methods) in the frame-work of the three design approaches. Detailed attention is devoted to: - the selection of the characteristic value of the pile resistance, accounting for spatial variability and stiffness of the structure; - the reliability of the prediction of the pile resistance using analytical or semi-empirical methods which may be accounted for through a "model factor". The results of a large test campaign on screw piles in OC Clay and a calculation example illustrate the proposed procedure when calculation rules using CPT results are used.

Jan 1, 2002

By Perry D. Teitelbaum

In two earlier studies the Federal Bureau of Mines undertook to explore comprehensively the dimensions of the Nation's energy balance. The first of these studies, published in 1950 as Bureau of Mines Information Circular 7582, by Harold J, Barnett, was primarily concerned with projections of future domestic energy requirements and supplies, because these related to projected growth in major fuel-consuming sectors of the economy, changing rates of energy-use efficiency, and interfuel substitution patterns. But, to provide the essential background for these projections, it was first necessary to assemble and examine in some detail the quantitative information on the size and shape of the current United States fuel economy. Among other things, Barnett's path-breaking study indicated the need to consider energy as an entity, particularly for public and private policy makers, industry and commodity analysts, economists, and others concerned with long range questions of domestic and international energy supply and demand. The study also spotlighted a gap in the fabric of current economic intelligence; no comprehensive collation and reconcilation in any single report of available published statistical information covering the origin -a disposition of all energy materials existed. In response to this latter need, the Bureau of Mines prepared the second of the two studies referred t3 above. This was published in 1951 as Report of Investigations 4805, by W, H, Lyon and D, S. Colby, and it consisted of statistical information on the production and use of each of the various fuels and electric energy in the United States for 1929, 1939, and 1947; all were presented in tabular form and on a uniform basis. The three years selected were chosen largely on the basis of data availability.

Jan 1, 1961

By Djavid Mohammad

Over the next several years, the storage capacity of the Metropolitan Water Reclamation District of Greater Chicago?s Tunnel and Reservoir Plan will be increased by 14.8 billion gallons through the addition of two large off-line reservoirs: the McCook and Thornton Reservoirs. The Thornton Reservoir will be constructed at the terminus of Calumet TARP System. The constructed TARP system will be connected to the Thornton Reservoir via connecting tunnels and gates systems. The connecting tunnels will comprise of: an upgradient transition tunnel, steel lined bifurcated tunnel for conveyance and control of flow, downdradient transition tunnel, and energy diffuser at tunnel portal. A large, approximately 250-foot-long, 69-foot-wide, and 40-foot-high, rock cavern will be excavated at an average depth of 320 feet to house the bifurcated tunnel system and associated six large control gates, each 12.5-ft by 28-ft wheel gate. Presented in this article are discussions about the TARP system, the Connecting Tunnels and gates Project, regional rock conditions, evaluation of reservoir?s wall stability for evaluation of tunnel penetration, and design challenges facing during design of the: rock cavern hosting the bifurcated tunnel system and gates and associated tunnels and shaft.

Jan 1, 2008

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

The granulites and related "dry" igneous rocks tend to be passed over during exploration for metals. Preliminary data show that high trace concentrations of eu, Ni, and other metals of economic interest are commonin orthopyroxene and some of the other granulite minerals. During retrograde metamorphism of granulites, pyroxenes are converted to amphiboles or phyllosilicates, and significant quantities of metals are released andbecome available for incorporation into new mineral phases, or may be transported elsewhere. S-rich scapolite is the normal scapolite of granulites. Its retrogression to secondary plagioclase provides much S which scavengesCu and Ni, from pyroxenes undergoing retrogression, thus producing ore-fluids. A full analysis of a scapolite with 5·10 per cent SOg is given.Beryl is unstable in granulites but the rare Be mineral taaffeite (Al4Mg(Be, FeII)Os) with 5·50 per cent BeO occurs in central Australia as a pale green tabular mineral easily confused for chloritoid in hand-specimen.Metamorphic differentiation and mobilization of primary ore concentrations are major factors controlling their post-granulite attitude and grade.Zones of retrograde metamorphism are commonly found cutting or engirdling granulite terranes. As the "volatiles" for the new hydrous minerals of many of these zones are of deep-seated origin and may be juvenile, sulphide mineralization in them may also be of mantle origin. However, it is likely that much of the metal content could be scavenged from the granulites as they are down-graded by juvenile volatiles. Major Bouguer gravity anomalies delineate some granulite terranes (e.g. Fraser Block, Western Australia), and are related to deep-seated geosutures and mantle disturbances.Many granulite terranes are linear belts and appear to be welded to older cratonic blocks.

Jan 1, 1969

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997

By F. D. Everett

This report summarizes the results of a nationwide investigation completed in 1964 to determine the nonferrous base metal ore reserves and potential sources of ore and to evaluate criteria for their ultimate exploitation. Engineers of the Bureau of Mines contacted mining company officials, reviewed reports and Government records, and where necessary made personal appraisals in arriving at the results. The estimates are presented by metals in ores in geographic regions and include some of the problems affecting the reserves and potential sources. The recoverable metal in the measured ore category and in the total ore reserves was estimated as follows: [ ] At the 1963 rate of domestic mine production these total reserves would be adequate to provide copper for 62 years, lead for 121 years, and zinc for 42 years. Data also are given for gold, silver, and other coproducts. Reserve estimates greatly exceed those of previous investigations; some prior estimates of copper reserves are included for comparison (table 23). Projections of requirements for base metals indicated the United States will need approximately 45 percent more copper in 1970 and 110 percent more by 1980 than was consumed in 1960; similar projections for lead indicate increases of 20 percent by 1970 and 45 percent by 1980; zinc projections are 40 percent more by 1970 and 90 percent by 1980. Much of the production of gold and silver is a coproduct of base metals recovery and the projected need for the precious metals exceeds all the United States can produce. Some problems of the industry are mentioned. A graphic evaluation of the economic availability of the reserve and potential sources is shown.

Jan 1, 1967

By O. Celep, T. Uslu, Savas

This study investigates the enrichment of a low-grade colemanite concentrate (-3 mm) using a Knelson centrifugal gravity concentrator. Due to its low boron content, the concentrate is unsaleable and has to be stored under appropriate conditions to avoid potential environmental problems. The low-grade colemanite concentrate was comminuted to size fractions of-1 mm, -0.5 mm, and -0.15 mm before treatment in the Knelson Concentrator. The effects of particle size, fluidizing water velocity, and bowl speed on the enrichment process were examined. The B2O3content of the concentrate was increased from 33.96% to a maximum of 45.52%. B2O3recovery increased with increasing bowl speed and particle size, and decreased with increasing fluidizing water velocity. The enrichment process also rejected arsenic and iron to some extent, with a maximum reduction of arsenic from 1360 g/t to 765 g/t and iron from 0.88% to0.33%.

Jan 1, 2015