Search Documents

By Zhi-gang Que, Sheng-li Wu, Guo-liang Zhang, Bo Su, Chao-gang Hou

NOx released during fuel combustion is one of the major air pollutants, such as acid rain and photochemical smog. At present, still not have an economical and effective method of inhibiting NOx emission for sintering flue gas. Therefore, controlling conditions of fuel combustions to enhance the reduction of NOx is important for decreased the emission. In this study, microsintering furnace has been performed to investigate the effects of NOx emission from char-N during coke breeze combustion. The results show that the emission concentration of NOx decreased with increasing temperature when it is sinter bed temperature higher than 1000℃. The lower emission concentration of NOx was obtained when the concentration of oxygen was decreased. And the maximum concentration of NOx will be reduced with the enhanced of heating rate. If heating preservation time was prolonged, it would promote to NOx reduction with reduction substances resulted in lower NOx emissions in the combustion of coke breezes.

Jan 1, 2015

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By Takuya Shinagawa

After vitrification of the residues from a municipal solid waste incinerator, the vitrified products can be used as a construction material, and the dust can be used as raw materials for the non- ferrous industry. The NKK electric-resistance furnace is operated under a reducing atmosphere, and heavy metals such as zinc and lead in the ash vaporize to form dust. Also, dust from the NKK electric-resistance ash melting furnace is composed of water insoluble zinc and lead components and water soluble NaCl and KCI. This is why, The concentration of zinc and lead in the dust after washing is sufficiently high for the dust to be used as a raw material for the zinc and lead industry. NKK developed a heavy metal recovery process in which zinc and lead in the dust are reclaimed as a raw material for smelting by making the best use of the characteristics of the dust.

Jan 1, 2002

By S. G. Kumar

Experimental studies on high carbon steelmaking through LD Converter - Vacuum Arc Degassing - Bottom Pouring route to produce low oxygen steels were carried out. The results indicated that it is possible to produce steel with a total oxygen content of less than 15 ppm. Thermodynamic and mass balance calculations are made on low-carbon steels that are treated by a complex deoxidation practice based on primary deoxidation of aluminum, manganese and silicon additions; followed by secondary deoxidation of vacuum degassing with simultaneous additions of aluminum. The results showed that primary deoxidation is mainly due to aluminum and the effect of carbon under reduced pressures on deoxidation of molten steel that is already killed by aluminum is negligible. The effect of process parameters on total oxygen content of steel, like carbon content, slag composition and inert gas purging, are discussed.

Jan 1, 1994

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By Xiaodi Huang, Matthew Andriese, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"The thermal decomposition and regeneration behaviors of wüstite were investigated by in situ high temperature X-ray diffraction (HT-XRD) under non-isothermal condition at heating rate of 4 K min-1 in vacuum ranging from 294 K to 973 K. Wüstite on heating decomposes to magnetite and iron up to 823 K, above which it exhibits marked tendency to regenerate. Investigation of thermal stability of the reaction system shows that the decomposition proceeds under kinetic reaction control while the regeneration is under thermodynamic control. Kinetics study based on the Coats-Redfern integral approximation method indicates that the decomposition reaction follows a Komatsu-Uemura model-based diffusion-controlled kinetics with activation energy of 32.860 kJ mol-1. The thermodynamics analysis of regeneration reaction demonstrates that wüstite regenerates at lower temperature than stoichiometric ferrous oxide.IntroductionOwing to its importance in preparing various magnetic ceramic/metal nanocompostites or nanocrystals with high values of coercivity for the application as recording media, wüstite (non-stoichiometric ferrous oxide) has been attracting the attention of scientists over a long period [1-6]. The thermal behavior of wüstite was investigated by several researchers and phase transformations due to thermal decomposition and regeneration of wüstite during the heating in a specific temperature range was observed [7-9]. In spite of wüstite being found to dissociate to magnetite and iron at temperatures lower than 848 K and then regenerates at higher temperature, a clear understanding of the reaction mechanisms is clearly lacking [9]."

Jan 1, 2012

By Charles Zimmerman

The Genesis gold mine, owned and operated by Newmont Gold Co., is located in section 31, T36N, R50E within Eureka County, Nevada along the Carlin Trend of sediment-hosted disseminated gold deposits. Mining commenced in 1986 with present mineable and stockpiled reserves listed at 17,711,000 tons of ore averaging 0.073 opt Au, totalling 1.292 million ounces of gold. Ore is primarily hosted within Devonian calcareous siltstones that have been subjected to intensive argillization and silicification episodes. Additional mineralogic and geochemical features of the Genesis ores include enrichment in iron-oxides, kaolinite, arsenic and antimony; the ore zone is relatively depleted in carbonates and sulfides as a result of supergene and hypogene oxidation. Two major structural zones enhanced the permeability of the siltstones and served as the main hydrothermal conduits within the deposit. Prior to the main ore stage, the host rocks were subjected to metasomatic effects caused by emplacement of the Juro-Cretaceous Goldstrike granodiorite pluton and associated dikes and sills. Micron-size gold occurs in clays, micro-crystalline quartz, and in arsenical complexes. Non-oxidized carbonaceous and sulfidic ores and silica-locked ores result in variable preg-robbing and refractory responses during cyanide recovery. Selective mining and milling has resulted in the successful treatment of the Genesis orebody.

Jan 1, 1988

By C. L. Lin

Transformation of linear grade distribution to volumetric grade distribution has been used to estimate the actual mineral liberation during wet, batch, ball mill grinding of a copper ore. The degree of liberation based on the multicomponent-multisize grinding liberation model using volumetric grade is lower than the apparent degree of liberation estimated from using King's linear intercept model.

Jan 1, 1987

By Qing-Yun Huang, Xiao-Yi Zeng, Bing Xie, Hong-Yi Li, Jia-Rong Yan

"In order to utilize vanadium resource in vanadium-titanium magnetite ore efficiently, vanadium distribution ratio between hot metal and slag should be improved during BF process, meanwhile the precipitating of Ti(C,N) in slag must be minimized. Effects of temperature, Ti02 content in the slag and basicity on vanadium distribution between slag and hot metal were investigated by experiment and thermodynamic calculation. The results indicated that high temperature, low Ti02 content and high binary basicity of slag were beneficial to increase the vanadium distribution ratio. The effects of temperature and Ti02 content in slag on vanadium distribution were stronger than that of slag basicity.IntroductionVanadium is an important element that is widely used in industrial fields. Most of vanadium resource is hosted in vanadium bearing titanomagnetite [l]. Vanadium bearing titanomagnetite is thus one of the domainate raw materials to produce the vanadium products. In other words, the comprehensive utilization of vanadium bearing titanomagnetite is beneficial for vanadium resource utilization. Vanadium bearing titanomagnetite sources are abundant in Pan Xi of China [4]."

Jan 1, 2013

By Fathi Habashi

In the past five years Cuba has been attempting to more than double its nickel production by constructing two new ammonia leaching plants. No metals are yet produced on commercial scale but a variety of oxides and sulfides. This report updates the Cuban nickel industry as a result of two visits : one at the invitation of the Cuban Ministry of Basic Industries in 1987 and the other as a consultant to the United Nations for the Cuban Laterite Project in 1989.

Jan 1, 1993

By Susanne Pignolet-Brandom

Fourteen samples of crushed Duluth Complex rock were characterized by the QEM?SEM automated scanning electron microscope image analysis system to evaluate the application of the system to mining waste rock characterization. The system can reliably distinguish the iron sulfides, the copper-iron sulfides and the nickel-iron sulfides. Calcite was distinguished from all other minerals except fluorite. The volumetric abundances were verified by comparing elemental abundances calculated using the QEM"SEM volumetric percentages and appropriate mineral compositions with elemental abundances determined by standard laboratory procedure. The pH and sulfate concentrations of rinse water from laboratory leach experiments correlated well with the mineralogical data.

Jan 1, 1989

By Jian Li, Guo Chen, Bingguo Liu, Hongying Xia, Jinhui Peng, Libo Zhang

"Decomposition of ammonium tetramolybdate to prepare Mo03 using silicon carbide crucible in microwave fields was investigated. The results were analyzed Using TG-DTG and X-ray diffraction. Meanwhile, the effects of heating rat, material thickness, socking time, socking temperature on the structure of preparing Mo03 were studied. TG-DTG curves show that the decomposition process of ammonium tetramolybdate is only one stage, in the temperature range 300-350°C, whose begin to decompose when temperature increases beyond 300°C. The molybdenum trioxide was prepared by thermal decomposition. The quality ofMo03 was not affected under the heating rat is 12°C/min. It was beneficial for decomposition ratio with the lower material thickness, longer soaking time, and higher soaking temperature. XRD curves showed that it is viable method for preparation of Mo03 by decomposition from ammonium tetramolybdate in microwave fields.IntroductionMolybdenum is widely used in national defense, aviation, industrial and agricultural production as rare refractory metal. Molybdenum trioxide is vital raw materials for the process of preparation of molybdenum. The traditional production technology of molybdenum oxide is that ammonium tetramolybdate is calcined in rotary kiln or 4-tube furnace [J,2J. But the longer production time, the higher production cost, the lower furnace thermal efficiency, and bigger the energy consumption, especially the powder is easy to leak, the working environment is poor by using rotary kiln [ 3 l _ The particle of molybdenum oxide is non-uniform by using 4-tube furnace because of the uneven temperature of every tube and the poor exhaust of boat bottom [4l _ However microwave heating is quick and uniformity, it is a meaningful research that the microwave is used in the process of calcining ammonium tetramolybdate."

Jan 1, 2013

By P. T. Velu, R. G. Reddy

"The use of emf measurements to derive classical thermochemical data has been in use for many years. The reaction associated with electrochemical process is harnessed in a galvanic cell and energy involved measured in terms of electromotive force. The property requirements of sensor electrodes used differ for various aqueous, molten salt and solid electrolyte systems. The electrodes for molten salt electrolytes need special care for construction. This paper describes the studies carried out using an Ag/ AgCI reference electrode. This electrode was used to measure the solubility of compounds in molten salt electrolytes. The results obtained using this electrode are in excellent agreement with the values from chemical analysis method.I. IntroductionThe technique of obtaining a metal from its oxides by electrolysis is more than a century old process now. In these processes, it has been well established that for halide electrolytes, only the dissolved oxides are available for the dissociation at the electrode to release the metal during electrolysis. Therefore, the solubility of metallic oxides in the molten salt electrolytes is an important parameter which determines the economical and technical viability of these processes. The widely used molten salts systems in halides are fluorides and chlorides. The fluoride electrolyte system is used in our present study.The viability of obtaining aluminum alloys by in-situ electrochemical processing has been outlined in our earlier publications[1-8]. Studies on the solubility of various alloying element compounds is a part of our ongoing research efforts for the direct production of Al-Li alloys. As mentioned above, the solubility of lithium oxide and lithium carbonate compounds in molten fluoride electrolyte system have studied using EMF technique. The change in potential of the molten electrolyte was measured by a working electrode against the reference electrode with the addition of lithium compound."

Jan 1, 1997

By F. K. Letowski

Leaching in froth is a particular case of a three phase (liquid-solid-gaseous) process which combines flotation with leaching by using a reactive gaseous reagent as a flotation carrier and a leaching solution as the reactive liquid medium to fonn the foam (froth) in' which the solid particles are suspended. Some physico-chemical and engineering aspects of leaching in froth are discussed and illustrated by its application for cleaning the mineral graphite. Leaching of the graphite concentrate containing 4L4% of the elemental carbon and 3.16% of the sulphidic 'sulphur was canied out in the froth fonned by: (a) a concentrated chloride solution, with a small addition of nitric acid, in the foam state; (b) a mixture of gaseous O2, NO., and H20 encapsulated in the foam; and (c) notable particles of graphite suspended in the foam. The laboratory experiments werecanied out in a "flotation column"-type reactor ala temperature from 80 to !08°C and under total pressure of 100 to 200kPa. In the 3-stage leaching-flotation process, the non-flotable fraction of particles was separated three times from the notable fraction. The concentration of carbon and elemental sulphur in the final flotable fraction was 96% C and 0.38% S respectively. The expected advantages and possible application in hydrometallurgy are suggested.

Jan 1, 1995

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By Richard S. Dennis

Acid recovery employs ion exchange (I-X) resin as separation media for inorganic acids from dissolved metallic salts by physical adsorption and without the use of chemicals. This technology has been used for years on spent etching and plating liquors to recover acid for reuse in the bath and to reduce waste acid neutralization costs. It is also used for electrolyte treatment to facilitate valuable metal recovery via acidity reduction. TETRA's ccrxr'" I-X contactor has been used successfully for acid separation from its metallic salt counterpart in a simple, continuous operating mode using strong base anion resins. Efficient separation is enhanced by acid reconcentration to nearly its original strength or as high as 14-20%. Continuous treatment also recovers heat to the tankhouse or bath and improves metal quality due to consistent acid quality. Conventional fixed bed ion exchange (I-X) systems are impractical for acid recovery because of complex control design and large resin inventories needed to process very low liquid-to-resin treatment ratios associated with strong acid concentrations.

Jan 1, 1996

By Y. Fautrelle, F. Felten, O. Metais, Y. Du Terrail

"We deal with the prediction of electromagnetically-driven turbulent flows by means of a Large-Eddy- Simulation method (LES). The model is applied in the case of a liquid metal pool submitted to a polyphase linear electromagnetic stirrer. We investigate two cases: (i) the frequency of the magnetic field is equal to 50 Hz; in that case the effects of the pulsating part of the Lorentz forces may be neglected; (ii) the frequency of the magnetic field is low (f= 1 Hz), then the oscillating part of the electromagnetic forces is taken into account. The LES predictions agree well with the mean velocity measurements, as does the standard k-a model. However, as for the turbulent kinetic energy predictions, there is a large discrepancy between the two models. When the oscillating part of the Lorentz forces is taken into account, the computations show that the fluid flow is sensitive to the unsteady part of the forces. We find that the mean velocity is not affected by the fluctuating component of the force. As for the turbulence parameters, the presence of the pulsating part leads to a significant reduction of the turbulent kinetic energy, whilst the turbulence length scale decreases.IntroductionElectromagnetic stirring is commonly used in various metallurgical processes. In continuous casting for example, it may improve the structure of the solidified metal products. Fluid flows generated by electromagnetic stirrers have been extensively investigated (1 ). As for numerical predictions, many works have been published on the subject. In most of the previous works, onepoint closure models have been used. The most used model is the well-known k-i:: model. Those models yield fairly good results as for the mean velocity prediction. However, it has two main drawbacks:(i) the turbulence is not predicted accurately,(ii) it is not well fitted for unstationary flows as well as transitional turbulent motions, where theReynolds number is moderate."

Jan 1, 1999

By Cui Wang, Bing Dai, Haibin Zuo, Jianliang Zhang

The damage mechanism of ductile cast iron cooling stave applied to No.4 blast furnace of Guofeng steel was analyzed through damage investigation in details, the damage causes: hightemperature gas flow erosion, wear of burden, high-temperature ablation, carburizing damage, improper operation on blast furnace, etc. were given out both in macroscopic and microscopic views. It can be obtained from metallographic diagrams that the diameter of graphite nodules increases, the number per unit area reduces, and roundness declines, successively, from cold to hot surface, which are not conducive to stave longevity. In summary, the material for staves manufacture should be better in comprehensive mechanical properties to prolong the service life, thus making blast furnace long campaign.

Jan 1, 2015

By Chao Zhang, Kexin Jiao, Yi Qian, Jianliang Zhang

Now low-grade iron ore were widely used. However, one prominent problem is that the content of trace elements is higher than that in high quality iron ore. For the requirement of the content of Mn, Cr, Ni, Cu, and Ti in hot-rolled steel sheet and strip, the upper limits of these elements in sinter will be studied in this paper. Using the activity model of aggregation of electronic phased slag composition, the distribution ratio of each element in converter is analyzed and the content of each element in hot metal is calculated. Furthermore, through the thermodynamics method, the distribution ratio of each element in BF is analyzed and the content of each element in raw material is calculated. The upper limits of Mn, Cr, Ni, Cu, and Ti in sinter can be determined by calculating, the values are as follows: Mn 0.767%; Cr 0.552%; Ni 0.055%; Cu 0.159%; Ti 0.108%.

Jan 1, 2015

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016