Search Documents

By Francis B. Gularte

The Dalles Dam is located 192 miles upstream from the Columbia River?s mouth. As part of an effort to increase survival rates for young salmon migrating downstream to the Pacific Ocean, a river spillwall was constructed to guide the young salmon into the thalway and out of the reach of predators. The spillwall consisted of 43 large precast concrete cells constructed onsite. The 120-ton cells are positioned on the bedrock riverbed to form the 830-foot-long spillwall. Large capacity post-tensioned strand anchors extend through ducts in the precast units, anchoring the wall to the basalt. One hundred seventy-eight tie-down anchors consisting of 30, 32, or 40 strands were installed and post-tensioned to secure the cells. The logistic and technical challenges presented by positioning, installing, and stressing the precast cells in the tailrace of a large dam required a high level of cooperation and planning between the owner, general contractor, subcontractors, and suppliers in order to finish the project within the allotted in-water work windows to minimize impacts on seasonal salmon migration.

Jan 1, 2010

By Miguel E. Ruiz, America L. Fernandez, Miguel A. Pandon

"Post-grouted drilled shafts (PGS) are a deep foundation system in which grout is injected at high pressure throughout the tip after the drilled shaft has been installed. Pressure grouting of drilled shaft tips can significantly increase the ultimate capacity and stiffness of drilled shafts. Conventionally constructed drilled shafts usually require higher axial deformation to develop the available side friction and the tip resistance simultaneously. They also tend to have higher tip compressibility and reduced end bearing capacity due to disturbance at the bottom of excavation during drilled shaft construction. PGS foundations have been found to be a cost-effective solution to compensate for this capacity reduction and/or compressibility increase. PGS construction procedure counterbalances tip compressibility and end-bearing capacity reduction. The tip grouting also has a pre-stressing effect over the shaft side friction since the drilled shaft tends to move upwards during the pressure grouting of the tip. After grouting, a bulb tends to form at the pile tip pre-compressing any disturbed material and, in certain cases, increasing the tip area, thus increasing shaft tip capacity.PGS load-settlement predictions using a load transfer approach are presented in this paper and compared with corresponding load test data. The paper also presents the main findings of load transfer analyses that were carried out to investigate the potential different factors that may be contributing to the observed improved performance of PGS over conventional drilled shafts. Results show that the two main factors, that may have a significant contribution on the overall performance of the foundation by increasing its ultimate capacity at any given level of settlement, are the stress-reversal of the skin friction and the formation of a grout bulb at the tip. The grout bulb tip contributes primarily through the increased tip area and to a lesser extent through increased stiffness and strength of the soil in the vicinity of the pile tip."

Jan 1, 2005

By A. Ghorbani

The analysis of Combined Pile Raft Foundation (CPRF) is very complex due to involved interactions among components of CPRF system. Many researchers made efforts to develop sufficient methods including three dimensional finite element methods to compute these interactions. Since there are some restrictions and complexity in previous methods, in present study a new approach based on three dimensional finite difference methods is implemented to overcome some of these restrictions. The total and differential settlements of a centrifuge case study are computed using different numerical methods to show the performance of present numerical approach.

Jan 1, 2007

"This model specification includes sample text shown in normal font with commentary in italics. The commentary is intended to highlight project-specific items the specification writer should consider during development of the specification. In some sections, typical values are presented to indicate common practice, and these values may be changed to reflect project-specific requirements. The commentary should be removed before using the specification for a project. 1. SCOPE The work consists of designing, furnishing, installing, and testing helical piles used to support foundation loads (compression, tension and lateral), and any ancillary materials (e.g., load transfer devices, etc.) according to the project plans provided and these specifications. Unless otherwise noted, the installing contractor shall provide all labor, tools, equipment and materials necessary to install the required piles. The parties referred to in this specification are as follows: • The Owner is the property owner. • The Owner’s representative is the individual or firm hired by the Owner to design and oversee the overall project. • The pile designer is the individual or firm generally hired by the installing contractor to design the helical piles. • Installing contractor installs and tests (if necessary) the helical piles, and possibly tasks associated with the project. It is important to clearly define the roles and responsibilities of every party on each project to promote good communication and reduce potential for contractual misunderstandings. Different types of contractual vehicles (design-build, value engineering, etc.) require different roles and responsibilities for the various parties, which should be considered in specification development. The Owner will provide suitable access to the construction site for the installing contractor’s personnel and equipment. Unless specifically noted otherwise in the contract documents, the Owner will remove and replace any structures, utilities, pavements, landscaping or other surficial improvements in the work area as necessary to facilitate the work. The Owner will be responsible for overall construction oversight to minimize potential for developing unsafe conditions. The work may include post-construction monitoring of pile performance if required by the Owner or the pile designer to confirm performance of the piles subsequent to their installation. The work may also include installation of additional piles if the initial installation does not meet specified capacity or performance requirements. Responsibility for providing subsurface investigation shall be addressed in the bid documents. The Owner is responsible for providing to the installing contractor all available subsurface soils, rock and groundwater information and geotechnical testing data."

Jan 1, 2015

By Ørjan Nerland, Torgeir Haugen, Astri Eggen, Kjell Karlsrud

"Ground improvement by the deep dry mixing (DDM) method is used in Norway since the late 1970's. A brief review is given of the Norwegian guideline for ground improvement with DDM issued in 2012, but focus is on practical examples and experiences related to improving the stability of excavations and natural slopes in soft clays. Two examples deal with experiences from 10 to 18 m deep excavations in soft and partly highly sensitive clays, where DDM panels and block stabilization were used to both give sufficient stability against bottom heave and to limit lateral wall displacements. A third case deals with improving the stability of a natural slope in quick clay by installing DDM panels near the crest of the slope. To limit disturbance and excess pore pressures generated during the DDM works, vertical drains were installed in advance in between the DDM panels. This ensured that the excess pore pressures generated by the DDM works (up to 150 kPA) dissipated quickly, which was instrumental to avoid triggering a landslide during the stabilizing works.INTRODUCTIONThe lime column (LC) method developed in Sweden and Japan in the mid 1970's (e.g. Broms and Boman, 1977). Since then, there have been significant developments in Scandinavia and around the world in terms of rigs, mixing machinery and tools, and type of binders used. The method, presently named the ""Dry Deep Mixing"" (DDM) method in contrast to the wet deep mixing methods (WDM) that also have developed significantly over the past decades, e.g. Kitazume and Terashi (2013). The first application of the DDM method in Norway was in the late 1970's to improve the stability of an excavation in quick-clay, then using only lime as binder. Most DDM applications in Norway have also thereafter been to improve the stability of cuts, supported excavations or natural slopes in soft clays. The Norwegian Geotechnical Society (2012) issued in 2012 “Guidelines for design of ground improvement with DDM methods"". The following highlights design issues dealt with. The paper focuses however, on some practical cases where DDM has been used to improve stability of deep excavations and a natural slope in soft and partly highly sensitive clays."

Jan 1, 2015

By Richard Berry

The spacing of grout injections is typically about 2 to 2 V½ meters if the purpose of the grouting is densification of the in-situ soils. Hole spacing will vary with the in-situ soil properties and the grout injection rate; faster rates requiring closer hole spacing.

Feb 10, 2003

By Kyle L. Murrell

Along the southeast United States coast, clayey silt and silty clay marine formations may cause pile installation and integrity problems. More specifically, excess pore pressures which develop in these soils during driving can cause high displacement piles to rebound or ?bounce?. Bounce is defined as a large (¾-in. to more than 1-in.) downward pile displacement during the hammer blow with little to no net displacement at the end of the blow. Pile bounce can generate damaging tension stresses and result in inefficient pile installation. A case history is presented where pile bounce was observed during the installation of 20-in. square ?high displacement? prestressed concrete piles which support a new ferry terminal in coastal North Carolina. High-strain dynamic pile testing was performed during test pile installation to evaluate driving stresses, pile capacities, and hammer performance. During and after installation of numerous production piles, circumferential cracking was observed on some of the piles. Additional high-strain dynamic pile testing was performed on two piles installed with a hammer having a heavier ram than the initial hammer. The new driving system generated lower tension stresses and installed the 20-in. piles more efficiently. Low-strain integrity testing was performed on the piles to qualitatively assess the cracks and locate any unidentified cracks. The low-strain testing was performed on piles installed at least a week prior to testing and on piles installed immediately prior to testing. When low-strain testing was performed immediately after pile installation before dissipation of excess pore pressures, pile integrity could be evaluated to depths of at least 12 pile diameters deeper than when performed weeks after installation.

Jan 1, 2008

By C. Guney Olgun, Charles Elks, Sherif L. Abdelaziz, James R. Martin, Christopher Fox, Pier Luigi Iovino, Fatih Catalbas, Pierre Gouvin

"Energy piles are a new innovative renewable energy technology to access and exploit the relative constant temperature of the ground for efficient heating and cooling of buildings. Examples of energy piles include drilled shafts, continuous flight auger (CFA) piles, driven piles, and micropiles. A field test setup was installed at the Virginia Tech Geotechnical Research Facility to study energy piles. The field test consists of a total of five micropiles 25 cm (10 inches) in diameter, four of which were equipped with circulation loops. The test piles extend to a depth of 30.5 meters (100 feet) and are heavily instrumented with strain gauges and temperature sensors. Several observation boreholes were formed around the test piles to monitor ground temperatures. Thermal conductivity tests and field load testing were performed to investigate the behavior of Energy Piles. This paper presents results of the thermal conductivity tests and thermo-mechanical field load test performed as part of this field investigation.IntroductionThere is a developing trend around the world to explore alternative energy sources. The main driving forces are growing global energy demand, depleting natural resources and the adverse effects of greenhouse gas emissions from fossil fuel consumption. Geothermal energy is one of the promising renewable sources that can be utilized to offset such trends. However the use of geothermal energy has been limited mainly to certain hot spot areas where it is used either for district heating and/or electricity generation. Ground temperatures below a depth of about 6 meters (20 feet) remain stable compared to outside air temperatures, typically lying between 8-23°C (46-73°F) at most U.S. regions. The constant temperature and heat storage capacity of near surface soils in any region represent a tremendous potential of stored energy that can be used for heating and cooling of structures."

Jan 1, 2017

By Michael Cianchetti, Nadir Ansari, Matthew Janes

"PROJECT DESCRIPTIONThe R C Harris Filtration Plant underwent an expansion to install an underground sludge treatment capability consisting of a series of underground tanks within stepped excavations 12m (39 ft) and 10m (33 ft) deep into compact, wet sands over stiff clays and clayey silts.Concerns regarding the original structure influenced designers to set the lateral deflection limit for the proximal front footing at 4mm (1/6 in), (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Through extensive Fast Lagrangian Analysis on Continua (FLAC) and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept and met deflection concerns.GEOTECHNIQUEThe hillside site drops 14.5m (47.6 ft) over a distance of 53m (174 ft) between the existing Filter Building on the north and the Services Building on the south. The soils adjacent to the Filter Building consist of 6m (20 ft) of sandy fills, to the footing elevation, over compact sands and layered dense sands and silts to a depth of 10m (33 ft) below existing footing. Beneath the silts lies a 10m (33 ft) thick stiff clayey silt, 2m (6.6 ft) of sandy silt till (containing cobbles and boulders) and an artesian gravelly sand at a total depth of 30m (98.5 ft).The tender information was deemed inadequate to accurately determine soil parameters for a finite element analysis. As a result, the design-build team performed pre-tender Cone Penetrometer Testing (CPT), including dynamic analysis. The CPT data indicated stratigraphy consistent with the conventional bore hole exploration (SPT results) however, the CPT data provided consistently superior soil strengths. The CPT data indicated the sands and silts were dense to very dense throughout their full thickness. The clayey silts below the sands were found to have shear strengths in the 100 to 200 kPa (14.5 to 29 psi) range with an Over-Consolidation Ratio (OCR) ratio of 1.5 to 2. The dynamic analysis, while low strain, indicated very competent behavior with Young’s Modulus values in the 200 to 350 MPa (29,000 psi to 51,000 psi) range. The CPT derived shear moduli and OCR values were vital in determining the soil engineering parameters used for the FLAC analyses."

Jan 1, 2007

By Rouzbeh Afsharhasani, Moses Karakouzian, Brandon Kluzniak

"The Vegas High Roller is the centerpiece of a new development parcel adjacent to the Las Vegas Strip. At a height of 550 feet, the High Roller is currently the tallest observation wheel in the world. The design team conducted a geotechnical site investigation to characterize the alluvial soils and cemented layers encountered and to provide foundation design recommendations for the observation wheel, boarding platform, and temporary structures needed to erect the wheel structure. This paper presents a case history of the geotechnical design process, including development of a ground model and design parameters, high-strain dynamic axial load tests, and settlement monitoring during construction. Results indicated that design parameters were conservatively assumed and that the majority of the axial load was transferred to a near surface caliche layer, thereby resulting in insignificant settlement of the foundation system.IntroductionThe engineering of the Vegas High Roller is similar in concept to that of the London Eye and the Singapore Flyer. The wheel has 28 cabins, each with a capacity of 40 persons. The top point of the structure is 550 ft above ground level at the site.A geotechnical site investigation program was undertaken and subsequent analyses were performed to provide foundation recommendations for the observation wheel legs, boarding platform columns, and temporary structures directly associated with construction of the observation wheel."

Jan 1, 2017

By Naoyuki Hanawa, Takeo Asanuma, Tatsuo Nagatsu, Sachihiko Tokunaga, Daisuke Nakagawa, Yoshiyuki Morikawa, Kazuhiko Ueno

"In the cement deep mixing (CDM) method, one approach to joint construction is creating a surface-contact joint. In this study, an unconsolidated-undrained triaxial compression test was performed on cement-treated soil specimens with joints artificially created by successive pouring. The effects of the presence or absence of such successive pouring joints on the strength of the specimens were then examined. The results showed that the compressive strength of the specimen decreased by approximately 0%–30% with a successive pouring joint.INTRODUCTIONIn the block type and wall type improvement patterns of the CDM(Cement Deep Mixing Method) application, an integrated body of soil-cement columns is constructed by partially overlapping individual treated soil columns. The overlapping operation should be implemented before the hardening of soils by cement progresses and thus, this operation is routinely performed in construction sites usually within 24 hours or within 48 hours at a maximum. However, when the operation is forced to be interrupted on account of a typhoon or any other adverse weather conditions, it is impossible to carry out the overlapping operation within the above time limitations. In such a case, it is necessary to improve the integrity between the treated soil columns solidified first and the treated soil columns to be constructed later.One of the methods that can be adopted is to prior agitate the target area by mixing blades “without cement”, integrating the preceding treated soil columns and the subsequently treated soil columns at construction joints. This method has been adopted so far in numerous sites because no additional materials or equipment are necessary. However, its effectiveness has scarcely been evaluated quantitatively in conventional studies.In the circumstances, the authors investigated in the present research the effect of the presence or absence of construction joints on the specimen strength by performing unconsolidated-undrained triaxial compression tests using specimens of cement treated soil artificially provided with surface-abutting construction joints.Therefore, this study examined the effects of the presence or absence of artificially created successive pouring joints on the strength of cement-treated soil specimens through an unconsolidated-undrained triaxial compression test."

Jan 1, 2015

By Dileej M. Dewaikar, Poonam A. Patil

"In this paper, the ultimate lateral resistance of a long, flexible, unrestrained vertical pile in a cohesive soil is computed under static loading condition using py curves. A simple and improved method for the construction of hyperbolic p-y curves for a cohesive soil is proposed for static loading conditions. An iterative analysis is employed with secant modulus approach, using a matrix method known as moment area method developed by Sawant and Dewaikar. The loadground line displacement relationship is obtained for different load eccentricities using p-y curves developed by Matlock, Georgiadis et al. and the proposed hyperbolic p-y curves for different eccentricity ratios. These values are compared with the values computed from model test performed by Rao et al. and with the limit equilibrium solution given by Broms. The comparison shows that, the results obtained using hyperbolic p-y curves shows a better agreement with the model test data with the maximum difference within 15% using other methods; whereas Broms' limit equilibrium solution shows some agreement with the results based on Matlock's p-y curves.INTRODUCTIONPile foundations are used for jacket type offshore structures, which are subjected to large magnitudes of lateral loads due to lake or ocean waves, winds and ice forces. The failure of a pile-soil system is catastrophic and excessive deflection of the pile creates operational difficulties. In the view of this, bending moment in the pile is required to be predicted in a rationar manner. The p-y concept developed by Reese and Matlock (1956) is popularly being used to estimate the pile top deflection and bending moments.The ultimate lateral load which causes collapse of a pile-soil system is generally estimated using Broms' (1964) method, which is based on limit equilibrium considerations. The p-y curves are basically nonlinear in nature and include ultimate pressure at the depth where they are generated. Therefore, if the lateral deflection of pile top against different magnitudes of lateral load is obtained, it should be possible to obtain the ultimate lateral load from this load-deflection relationship."

Jan 1, 2005

By Dennis Nottingham

Increased interest in seismic soil liquefaction and preventative soil stabilization sets the stage for improved deep compaction methods using pile driving techniques. In 1971 L.B. Foster Company personnel patented a method of deep compaction using a vibratory pile hammer and pile probe. The technique had some success, but did not produce consistent results and thus found its way to obscurity. Other patents attempted to modify the technique by various probe modifications, but again without measurable improvement from a practical point of view. Solutions to economical deep compaction up to 100-foot depths particularly in saturated granular soils would have a great impact on the construction industry and new bulkhead structures being developed, thus PND was prompted into related research and development. The advent of higher horsepower vibratory hammers, coupled with PND engineers' experiments, observations and measurements, led to an "H" pile probe design which has produced measured soil density improvements up to 250% using SPT "N60" values as a measure. Case histories of two projects involving extensive SPT soil sampling comparative measurements will be discussed along with findings that led to the compaction success. Applications to numerous modern "Open Cell" bulkhead projects will be presented and discussed.

Jan 1, 2004

By Shigenori Horikawa, Nobutaka Tanaka, Toshiro Hara, Kengo Yamamoto

"The CDM-LODIC method(Low Displacement and Control method), a modified the CDM(Cement Deep Mixing) method, reduces the ground displacement through the removal of in-situ soil equivalent to the amount of slurry injection using the continuous auger flight attached on the shaft above the conventional the CDM mixing tool. The reduction of ground displacement minimizes the impact on adjacent buildings and other infrastructures. Since the development of the CDM-LODIC in 1985, this method has been used for more than 900 projects with total volume of improved soils exceeding 5.3 million yd3 (7 million m3). The ground displacement that could be caused by deep soil mixing is controlled by balancing the volume of discharged soil and the volume of slurry injected for soil mixing. This paper presents the ground improvement work for the Sanriku Coast Expressway Project using the CDM-LODIC method to 1) control the ground displacement during ground improvement to minimize the impact to existing buildings and facilities and 2) utilize low height CDM-LODIC equipment to avoid potential damage to critical facilities in the vicinity of ground improvement area and avoid interference on the normal operation of the Ishinomaki Red Cross Hospital.INTRODUCTIONSanriku Coast Expressway is a reconstructed highway, which is part of an early restoration program to recover from the Eastern Japan Earthquake of March 11, 2011. This highway extends 223 mile (359 km) and connects the Pacific Coast regions of three prefecture of North Eastern Japan as shown in Figure 1. Along a section between Yamoto - Ishinomaki road, the highway was expanded from two lanes to four lanes to mitigate traffic congestion for the adjacent city center and hospital and to serve as an efficient transportation route for emergency or disaster relief needs as shown in Figure 2. Deep mixing ground improvement with an area replacement ratio of 50% was designed to provide settlement control under the new fill embankment of the expanded highway as shown in Figure 3. The original CDM treatment layout using 5.2ft (1.6 m) diameter columns is shown in Figure 4."

Jan 1, 2015

By Hitoshi Ogura, Koichi Kobayashi, Sadao Yabuuchi

"In Japan, most pile foundations using pre-cast concrete piles are installed by the bored pre-cast piling method, wherein pre-cast piles are installed in holes that have been excavated beforehand and filled with cement milk (term used for cement water slurry in Japan). The bored pre-cast piling method with enlarged base, in which the portion near the toe is enlarged during boring operation, is widely used because of the cost benefits and the increased vertical bearing capacity that this method offers.The EX MEGATOP method, further developed as an improved bored pre-cast piling method with enlarged base, is reported here. The features of this method are: (1) High vertical bearing capacity; (2) High degree of freedom in design; (3) Excellent workability; and (4) Friendly to the environment. In particular, high vertical bearing capacity can be obtained using nodular piles and by enlarging the area at the pile toe and shaft. This method can gave a vertical bearing capacity coefficient at the toe of a=430, more than twice the corresponding value of a = 200 of a conventional bored pre-cast pile. Moreover, the shaft resistance can be several times larger than that of a conventional bored pre-cast pile. This report gives an overview of the EX MEGATOP method, evaluation of vertical bearing capacity, and examples of application of the method.1.lntroductionMost pile foundations in Japan are installed by the bored pre-cast piling method, that is, in holes that have been excavated beforehand and filled with cement water slurry, referred to as 'cement milk'. The ""bored pre-cast piling method with enlarged base"" is frequently used. In this method an enlarged excavation is used near the pile toe to increase the vertical bearing capacity.The EX MEGATOP method is a variation of the bored pre-cast piling method. Its features include the use of nodular piles and a long, enlarged excavation. The vertical bearing capacity of the EX MEGATOP method is described in this report."

Jan 1, 2005

By Kyle Murphy, John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closedloop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermomechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermomechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

Jan 1, 2017

By John S. McCartney

This paper focuses on the seasonal thermo-mechanical response of two energy foundations installed at the new Denver Housing Authority Senior Living Facility in Denver, Colorado. The two drilled shaft foundations, which have diameters of 36 inches and depths of 45 ft and are end bearing in the Denver shale formation, include a closed-loop series of polyethylene tubes through which fluid is circulated to exchange heat with the surrounding ground. The tubes within the foundations are coupled together with the conventional ground source heat pump system for the building and were installed to evaluate the heat exchange response of the foundations as well as any thermo-mechanical soil-structure interaction effects. A series of vibrating wire strain gages and thermistors were installed at different depths in the foundation to record the thermo-mechanical strain and temperature at different depths. Also, pipe-plug thermocouples are used to measure the inlet and outlet temperature of the heat exchanger fluid entering each of the foundations, which is necessary to evaluate the total heat exchange for the foundations and the efficiency of the heat pump. This paper will describe the energy foundation construction processes, the strain distribution and ambient temperature profiles during building construction and the seasonal strain and temperature distributions during heating and cooling of the building. The data indicates that typical heat exchange associated with heating and cooling operations leads to strains which are within acceptable limits, and that the foundations can provide a clear option for absorbing the base heating and cooling load for the building.

By Glen M. Bellew, James F. Mehnert

"The Kansas City District-United States Army Corps of Engineers has completed the design modification of a pile supported floodwall located along the Missouri River in Kansas City, Kansas. This deep foundation supported floodwall protects over 2 billion dollars in infrastructure, is approximately 17 ft (5.2 m) tall and is 1,446 ft (440.7 m) long. Design modifications included the addition of a row of drilled shafts and the addition of relief wells. Typically, deep foundation design is controlled by total stress analysis and undrained soil strength. Neither controlled design at this site, where effective stress and drained strength controlled. During high river stages, artesian pressures develop, leading to a reduction in both effective stress and pile capacity. Deep foundation analysis software available to the designer does not allow these effective stress conditions to be directly entered, so a unique way was developed to account for them. A load test was performed to verify the design. During load testing, the supporting ground was unsaturated and had effective stress conditions different from those that controlled the design. A load test evaluation process involving unsaturated soil mechanics was developed and performed. This paper will share both the effective stress design process used and the load test interpretation process performed.INTRODUCTIONThe Fairfax-BPU Floodwall is part of the Fairfax-Jersey Creek Flood Protection Unit in Kansas City, Kansas. The floodwall was built in the 1940s and currently provides Missouri River flood protection for over 2 billion dollars of infrastructure in the Fairfax Industrial Area. The floodwall averages 17 ft (5.2 m) in height, is 1,446 ft (440.7 m) in length and is divided into 35 separate monoliths. The originally constructed foundation support for each of these monoliths typically consisted of three rows of seven tapered steel monotube piles, each roughly 20 ft (6.1 m) in length. All monontube piles are tipped in sand, well above bedrock."

Jan 1, 2016

By Todd W. Armstrong, Michael D. Reader

"INTRODUCTIONThe Playa Vista Development is the largest urban infill development in the history of the United States. Overall, it encompasses about 1100 acres in the City of Los Angeles and is situated north of Los Angeles International Airport near the Pacific Ocean. The development taking place on the project consists primarily of high-density residential condominiums with 1 to 2 levels of subterranean parking . The geotechnical conditions are typified by high groundwater, soft clays, and liquefaction, in addition to environmental issues such as methane.Due to a combination of the geotechnical factors and noise restrictions, both driven and drilled piles were not feasible once the initial phase of the project was occupied. As a result, the project developer undertook a testing program that consisted of the installation and load testing of 9 piles in order to obtain City of Los Angeles acceptance of a pile installation system that met the site constraints. The testing program was divided between two separate contractors operating on sites set on opposite sides on the street (Figure 1 ). Contractors working in Test Areas A & B employed the ""dry dip"" and ""wet dip"" methods of auger pressure grouted displacement (APGD) pile installation, respectively.This paper summarizes the extraordinary program undertaken to install, document, test, and examine auger pressure grouted displacement piles at this site. The program ultimately resulted in City acceptance of auger pressure grouted displacement piles, a historically difficult challenge given the City's resistance of acceptance of ""new"" technologies.A summary of elements included in the test program are: (1) quality control; (2) load testing; (3) long-term testing; (4) non-destructive testing; and (5) pile exhumation."

Jan 1, 2005

By Eric Rehwoldt, Walt Rabe, Jesús Gómez, Tim Myers

"An expansion plan for Washington Dulles International Airport is currently underway to prepare for growth at this northern Virginia facility in the future. While Dulles currently serves more than 20 million passengers a year, when the Master Plan for the Airport is fulfilled, it will be capable of handling approximately 55 million passengers a year. The current Capital Construction Program underway at Dulles will take the Airport one step closer to its full potential.As planned, work includes a new Airport Traffic Control Tower, expansion to existing concourses, a fourth runway, additional parking, and other improvements. One of the most interesting features of this project is the construction of a two-track passenger train system (Automated People Mover, or APM) linking the main terminal and concourses, which will largely replace the Mobile Lounge transportation system, thus greatly reducing surface traffic. Construction of the APM system involves deep excavations along the tunnels and at the transfer stations. This poses special challenges because the settlement-sensitive terminal, original Airport Traffic Control Tower, and concourse buildings, as well as other facilities, exist near the proposed below-ground stations. The site is also underlain by a tight grid of underground utilities that include jet fuel, gas and central communication lines, in addition to more mundane electric, sewer and water mains.One of the most interesting features of this project was the extensive and skillful utilization of micropiles for support of existing structures adjacent to the excavations. Without the use of micropiles, the cost and difficulty of the excavations would likely have been much more. Several important lessons were learned about the use of micropiles, which advance that technology.Throughout the project site, bedrock was generally encountered at 25-ft depths or more. The rock consists of micaceous and highly calcareous siltstone rock. This rock is typical of the sedimentary component of the Culpeper Basin, a Triassic Age geologic feature extending from south central Virginia to western Maryland. The siltstone beds dip gently to the west at about 10 to 20 degrees. Joint planes typically dip 60 degrees to vertical. The rock underlies a sequence of fill materials and residual soils of varying thickness."

Jan 1, 2009